Just did this on my 2017 Challenger RT. Worked perfectly. 2 things: Lowes now sells these toggle bolts for $4 instead of $2 and change you mentioned in the video. The plate goes slightly below the lower lip of the bumper, so any speed breaker or anything that hits the plate will most likely damage the grill. I might go some other route for this reason, but the video was extremely helpful and easy to follow.
This video was super helpful. I used the same principle to install my front plate on my Mercedes C250. Saved me about $150 plus labor quoted by the dealer. This was also much simpler than using the zip tie methods I watched in other videos. Worked great. I'm now legal in California. Thank you!
I just did mounted my original license plate bracket upside down on the front right center of the front of the car on my new 2021 Dodge Challenger. It worked perfectly! It's looks spectacular! It looks better than any aftermarket bracket that I could have purchased. I would gladly buy you a case of beer. You saved me a lot of money. Thanks!
Just did my 2015 Durango. In order not to put pressure on the grill when tightening the bolt, I measured the distance between the grill and the plate and cut Two plastic spacers. Positioned the spacer between the plate and the grill and was able to tighten the bolts with no pressure on the grill. It looks great. Thanks for the tip.
OMG! I am thrilled I found this video. I just got a brand new Challenger and did not want to drill holes in the bumper. This is the perfect solution! Thanks!
This is a brilliant idea. If you want to attach a front license plate without drilling holes, this method is far better than using hook and loop or double-sided tape, either of which could come off in the heat or be easily stolen. Thank you so much!
Thank you!!! Just used this for a 2018 Jeep Compass...they delivered it without installing the front plate mount (left it in the plastic on the back seat)....took a little finagling since you can’t put your hand behind the grill, but I held the “toggle” portion still with one screwdriver while turning the screw with another one.
Thank you, friend. Went to Lowe's tonite, got the toggle bolts and strapped our license plate on our 2019 Cherokee. Don't know why Chrysler decided to do, Do It Yourself license plate frame installation.
You’re a genius. It worked on my 2023 Challenger. The only thing is that the grill ports are so small that you have to use pliers (I used a Leatherman) to maneuver and hold the toggles on the inside - a low power drill is highly recommended for the tightening.
Very helpful video. I just learned what toggle bolts are. I'm going to try this on my '12 Charger. Hopefully it will work. I was just pulled over and given a warning no front plate.
Great idea, but what happens the first time you drive up a driveway or a speed bump that catches that and rips it out? Since it hangs lower than the already low clearance.
I just did this for my 2015 Dodge Journey. I couldn’t find 1/4 by 6in bolts, so I used 1/4 by 3in. I basically rigged the holes to fit the bolts. But, job accomplished! Thank you so much for this video because I refused to drill holes in my bumper!
My GMC TERRAIN does not have it either. I just noticed. I am going to go to Autozone and get plate holder and the toggles you show here. In TEXASS i have to have a front and back but i am waiting for my new plates to show up.. BRILLIANT idea!! OMG thanks!!! Kudos..Kudos
Did something similar on my daughters new Camaro she purchased last year but used Plastic Cable Ties instead. Worked out very well. At lease they won't rust but I told her to keep a eye on them over the years she owns the car because they do go bad and become brittle over time and break.
I have a new Challenger and will consider this as a good alternative for relocation of the plate holder with a few mods to the retention method. Thanks for the idea.
Great idea man! I have the stock plate holder and also didn't want to drill. I learned about toggle bolts recently when doing some DIY home repairs. Great thinking!
Glad I was patient enough to find this video, I was determined not to drill into my Limited edition Superbee I just got. Thanks for the info, hope it will work on mine as well as yours and it still looks OK. I will let you'll know after I'm done, but it's gotta be better then the Holy bumper blunder Dodge passed to us!!!
Thanks for this video, this option is very inexpensive too. Maybe the only reason Dodge did it this way was because it would obstruct airflow. Minimally though, but probably an engineer would want every little for proper air flow. under and through the grill. The Show-and-Go is like $55, pay a little more for the ability to stow it.. Thanks again!
Looks like the best option for now although the bracket hangs a fuzz below the splitter. Being the first thing to make contact, I wonder what will happen when the front bottoms out and the bracket gets jammed up into the bottom of the bumper...just a thought.
Thank You. Just what I was looking for. Can't wait to go to the hardware store and pick up those quarter inch by 6 inch toggle bolts. Just picked up a 2016 Challenger SRT 392 and the dealer was gonna drill the plate on. I said hell no... Ill find another way. Thank God for youtube!!! Thanks again for the info.
Slightly scraped my splitter on a funky driveway again yesterday. If this plate location was installed, it would for sure have been jammed into the bottom of the bumper and/or cracked the plate frame. My 392 is striped and looking closer, the holes are already drilled under the stripe so I think I'll just do a bumper install and be done with it. If I ever want to relocate the plate, I'll just re-stripe that small bumper area and make the holes go away again.
Wish I had seen this video before I drilled holes in the bumper of my 2015 Dodge Durango. Now that I have, I'm going to have the bumper holes filled,painted, and mount my plate like yours.
My grill is different than yours but I made it work.(2016 R/T) thanks again for posting. I used some strong Locktite on the threads to keep it from loosening up.
Please explain to me how, now after using the two top holes for your relocation, how are you supposed to screw in the top two holes on your license plate?
Threw me off too. I thought he was going to attach the plate with the toggles; until I checked back at 00:17, you can see the 2 small holes toward the inside to attach the plate. There are only 2 because the plate slides up into the bracket flange.
i like it.. except that i scrape my charger scat back bumper all the time. this thing hangs down 1/2" - 3/4" lower than that, so it will scrape even worse?
I had zip ties on mine, but it still looked shitty! I drive around with no plate and have been lucky of avoiding tickets. When I park in public all l do is hook it with S hooks to avoid the ticket fairies.
good vid my cousin's going to be happy now , he has the same car he didn't want to to drill into to his bumper either unless we get a retractable license plate, will see,tnx forthe vid
I am going to try this on my Brand New Murano :) The plate now sits slant , so will get this and invert it and then see how it goes. helpful video , thanks
Thanks!! I just bought a 2019 R/T Plus and when I realized that if I was going to attach the front plate I’d have to drill into my brand new car my heart broke a little.
I tried but didn’t really like it. Then I found a product specifically made for this issue and LOVE IT. it looks so good on the car. It’s been a year but I’ll see if I can find a link to the particular one I got
Great video---I just bought a used 2017 RAM Truck that didn't have the front plate holder mounted, and in Ohio we have to have the front plate. Going to try something like this---no way I am drilling into my bumper! Thanks
That's an interesting take on an alternative. Can't do the center location on a 2015 SRT 392 that is fully loaded. There is a sensor right in the center of that area that you are covering. I thought about going off to the side, however I am concerned that I will be blocking 'some' airflow to the radiator.
Just did this on my 2017 Challenger RT. Worked perfectly. 2 things: Lowes now sells these toggle bolts for $4 instead of $2 and change you mentioned in the video. The plate goes slightly below the lower lip of the bumper, so any speed breaker or anything that hits the plate will most likely damage the grill. I might go some other route for this reason, but the video was extremely helpful and easy to follow.
Damn this is helpful. Great idea. We live in Texas and I did not want to drill into the bumper. Thanks man.
This video was super helpful. I used the same principle to install my front plate on my Mercedes C250. Saved me about $150 plus labor quoted by the dealer. This was also much simpler than using the zip tie methods I watched in other videos. Worked great. I'm now legal in California. Thank you!
You Sir, are a genius...
We moved here in Texas from AL and where we came from we don't have front license plates. Am trying it now.
I just did mounted my original license plate bracket upside down on the front right center of the front of the car on my new 2021 Dodge Challenger. It worked perfectly! It's looks spectacular! It looks better than any aftermarket bracket that I could have purchased. I would gladly buy you a case of beer. You saved me a lot of money. Thanks!
Just did my 2015 Durango. In order not to put pressure on the grill when tightening the bolt, I measured the distance between the grill and the plate and cut Two plastic spacers. Positioned the spacer between the plate and the grill and was able to tighten the bolts with no pressure on the grill. It looks great. Thanks for the tip.
+Chum joe awesome man, glad it worked out for ya
I'm picking up a brand new 2017 R/T Plus Shaker tomorrow and am SO GLAD I saw this. You sir, won the internetz for today!
OMG! I am thrilled I found this video. I just got a brand new Challenger and did not want to drill holes in the bumper. This is the perfect solution! Thanks!
Same here!👍
@@Donesan707 Me Too, brand new "19" RT. Crazy good idea !
This is a brilliant idea. If you want to attach a front license plate without drilling holes, this method is far better than using hook and loop or double-sided tape, either of which could come off in the heat or be easily stolen. Thank you so much!
Thank you!!! Just used this for a 2018 Jeep Compass...they delivered it without installing the front plate mount (left it in the plastic on the back seat)....took a little finagling since you can’t put your hand behind the grill, but I held the “toggle” portion still with one screwdriver while turning the screw with another one.
Thank you, friend. Went to Lowe's tonite, got the toggle bolts and strapped our license plate on our 2019 Cherokee. Don't know why Chrysler decided to do, Do It Yourself license plate frame installation.
You’re a genius. It worked on my 2023 Challenger. The only thing is that the grill ports are so small that you have to use pliers (I used a Leatherman) to maneuver and hold the toggles on the inside - a low power drill is highly recommended for the tightening.
Very helpful video. I just learned what toggle bolts are. I'm going to try this on my '12 Charger. Hopefully it will work. I was just pulled over and given a warning no front plate.
Great idea, but what happens the first time you drive up a driveway or a speed bump that catches that and rips it out? Since it hangs lower than the already low clearance.
I just did this for my 2015 Dodge Journey. I couldn’t find 1/4 by 6in bolts, so I used 1/4 by 3in. I basically rigged the holes to fit the bolts. But, job accomplished! Thank you so much for this video because I refused to drill holes in my bumper!
My GMC TERRAIN does not have it either. I just noticed. I am going to go to Autozone and get plate holder and the toggles you show here. In TEXASS i have to have a front and back but i am waiting for my new plates to show up.. BRILLIANT idea!! OMG thanks!!! Kudos..Kudos
i'm a lowrider for life and i am very creative ! thanks for your creativity good work thanx again !
Thanks for this vid! I recently purchased a 2019 Dodge Charger and I definitely do not want to drill holes in my bumper! This is awesome!
Did something similar on my daughters new Camaro she purchased last year but used Plastic Cable Ties instead. Worked out very well. At lease they won't rust but I told her to keep a eye on them over the years she owns the car because they do go bad and become brittle over time and break.
I have a new Challenger and will consider this as a good alternative for relocation of the plate holder with a few mods to the retention method. Thanks for the idea.
Great idea man! I have the stock plate holder and also didn't want to drill. I learned about toggle bolts recently when doing some DIY home repairs. Great thinking!
Glad I was patient enough to find this video, I was determined not to drill into my Limited edition Superbee I just got. Thanks for the info, hope it will work on mine as well as yours and it still looks OK. I will let you'll know after I'm done, but it's gotta be better then the Holy bumper blunder Dodge passed to us!!!
+clint mehling right on man, enjoy your superbee those are sweet rides!
Thanks for this video, this option is very inexpensive too. Maybe the only reason Dodge did it this way was because it would obstruct airflow. Minimally though, but probably an engineer would want every little for proper air flow. under and through the grill. The Show-and-Go is like $55, pay a little more for the ability to stow it.. Thanks again!
Toggle bolts. Such a simple idea. Great video man, huge thanks.
sure thing bud!
Bro this is extremely helpful. I am going to use your concept on my new Blazer. Thank you
Looks like the best option for now although the bracket hangs a fuzz below the splitter. Being the first thing to make contact, I wonder what will happen when the front bottoms out and the bracket gets jammed up into the bottom of the bumper...just a thought.
I hope in a minor bumper bump those toggle ends don't go through the AC condenser. Something to consider.
Dennis Weidenbach Negative Nanny
Have you ever poked a hole in the A/C condenser when installing a transmission cooler....because that's very disappointing when it happens.
Got to do this to mine today. Been riding around with my plate in the windshield for the last couple days
You are a hero my friend…
Thank You. Just what I was looking for. Can't wait to go to the hardware store and pick up those quarter inch by 6 inch toggle bolts. Just picked up a 2016 Challenger SRT 392 and the dealer was gonna drill the plate on. I said hell no... Ill find another way. Thank God for youtube!!! Thanks again for the info.
+qballer34 Glad it helped man, enjoy the car those 392's are badass
Slightly scraped my splitter on a funky driveway again yesterday. If this plate location was installed, it would for sure have been jammed into the bottom of the bumper and/or cracked the plate frame. My 392 is striped and looking closer, the holes are already drilled under the stripe so I think I'll just do a bumper install and be done with it. If I ever want to relocate the plate, I'll just re-stripe that small bumper area and make the holes go away again.
Fed Up sucks 4 u
You saved my pretty bumper! Thank you! Mopar should give you commission for such a great idea!
Glad I could help!
Wish I had seen this video before I drilled holes in the bumper of my 2015 Dodge Durango. Now that I have, I'm going to have the bumper holes filled,painted, and mount my plate like yours.
Hanksranger thanks for sharing this vid. Now I don't have to buy a flip up plate holder Great vid man.
thanks buddy, this is for sure cheaper!
+hanksranger Cheaper and still looks great. I'll do this mod when my plates come in.
My grill is different than yours but I made it work.(2016 R/T) thanks again for posting. I used some strong Locktite on the threads to keep it from loosening up.
Any alternatives to a horizontal grill? 😅
Fantastic hack for the Challenger. Just did this to my R/T.
I don't like how it looks in the middle... I installed mine on the far passenger side and it looks sick.
Peter Nabel installing it in the middle looks good
Do you have a pic?
@@AntLive29 no, it does not
That offset thing looks stupid .the middle is better
@@shevyjohn9308 to each his own
The best approach I ever seen, so smart!!!
Don’t like that’s it’s lower than the spoiler will hit something and brake grill plus it’s to low
This works for a 2022 Dodge Durango R/T as well. Thank you!
We got the same car! Great video
Just FYI . In TX you need to have the plate in the front and 12 inches from the ground..... just a heads up to TX folk
Nice going Bro! Thank you. I've been struggling to come to terms on drilling the holes. This is soooo much better.
Worked like a charm. Thanks
Wouldn't this disturb the air flow putting it over the grille?
Not really. There is a ton of airflow regardless
I'm doing this TODAY ⚠️ thank you for charing.
great idea, I've been look at alternatives since I moved from FL to CA where FL has one plate. awesomeness. and now CA has 2 womp lol
Great idea i just did this my mine. It looks pretty good
Would this work on an 18 since they changed the front grill size slightly, and do you scrape?
Please explain to me how, now after using the two top holes for your relocation, how are you supposed to screw in the top two holes on your license plate?
Threw me off too. I thought he was going to attach the plate with the toggles; until I checked back at 00:17, you can see the 2 small holes toward the inside to attach the plate. There are only 2 because the plate slides up into the bracket flange.
Cool. Solved my question on how now to drill into my 200.
Thanks, you're a boss! I'm planning to use a similar strategy on my Forte
i like it.. except that i scrape my charger scat back bumper all the time. this thing hangs down 1/2" - 3/4" lower than that, so it will scrape even worse?
yea unfortunatley it would
That looks good man. My dads dodge came with that but the chome bumpers already have the holes so I didn't have a problem luckily.
Great video! Huge help, thanks!
I had zip ties on mine, but it still looked shitty! I drive around with no plate and have been lucky of avoiding tickets. When I park in public all l do is hook it with S hooks to avoid the ticket fairies.
This is a great idea! I just did this for my car too.
Awesome video! Helped me out a lot thank you
good vid my cousin's going to be happy now , he has the same car he didn't want to to drill into to his bumper either unless we get a retractable license plate, will see,tnx forthe vid
Would it be a good idea to put the plate bracket in front of the radiator be as it is, or should it be more to the right or left of the bottom grill?
Dealership drilled into bumper. But now plates don’t match the holes to screw in
I am going to try this on my Brand New Murano :)
The plate now sits slant , so will get this and invert it and then see how it goes.
helpful video , thanks
Arun Post Yea this should work on other cars just as long as you can get the toggle bolts through. Glad it helped !
You the man hank ! Thank you
Thanks!! I just bought a 2019 R/T Plus and when I realized that if I was going to attach the front plate I’d have to drill into my brand new car my heart broke a little.
Did you do this?
I tried but didn’t really like it. Then I found a product specifically made for this issue and LOVE IT. it looks so good on the car. It’s been a year but I’ll see if I can find a link to the particular one I got
@@absolutetuber are you talking about the sto and sho? Hopefully not I seen those but they sit way to low for my liking.
No I thought those were hideous. This one sits exactly where the bolts in this video go
@@absolutetuber Cool if you could find it and link it I'd appreciate it
Wonder if this would work on early models...the grill is smaller then the model shown....neat ideal though....
I got some black plugs to put in the holes. Gonna get touch up paint for them
What happens when you have to take off the toggle bolts, is it possible to take them off?
Just undo the splash guard and put them back through 👍
Hank's Small Engine Repair alright! Thanks for the help, much appreciated!
I thought of this but mine has the adaptive cruise control sensor in the middle. So this method will block the sensor.
Helpful. Thanks for the video.
Yeah that is the first thing I noticed the spoiler is already way low. Damn....
Thank you! Very helpful
I decided to go the cheaper route with this. Hide-the-plate site is down for medical reasons of the owner. owell Thanks!!
I just bought a used challenger and it has this stupid thing on cuz it came from cali, i wanna take it off, how do i do it?
Where can I get the bracket? Mine didn't come with one in the trunk. Thanks In advance
rjsilva08 Dealership
Thx bro! Used this for my ride and it helped!
Great video---I just bought a used 2017 RAM Truck that didn't have the front plate holder mounted, and in Ohio we have to have the front plate. Going to try something like this---no way I am drilling into my bumper! Thanks
Thank you! I’m hoping this will work on my Mazda3.
Where can I find the bracket and toggle bolts? Thanks
Very helpful I’ve got to do pretty much the same for my 2017 equinox..
If the plastic harness scrapes the road won't it break the platic that you put the toggles in?
It’s only below the bumper about 1/2” if you’re scraping the road at stock height like that you have bigger issues
The 2015+ grill is different will this still work?
Are you able to remove this? Or is it a permanent solution. Only need my plates for a fix it ticket them going to take them off again.
It’s removable
Great idea, but Isn't the plate too low and you can hit something?
not really, I never had that issue
That's an interesting take on an alternative. Can't do the center location on a 2015 SRT 392 that is fully loaded. There is a sensor right in the center of that area that you are covering. I thought about going off to the side, however I am concerned that I will be blocking 'some' airflow to the radiator.
Where did you get the plastic bracket for the plate?
I’ve been scrolling through the comments trying to find the same answer!
got mine at amazon
I wonder if this will work on my charger🤔
great info bro
Do you need that exact bracket for the toggle bolts size or can you use a different bracket that's thinner
Honestly you can use whatever fits, I don't remember though exactly
@@hanksgarage_ ok thank you
Where did you get the Frame ?
Work with the charger 15+??
Would this specific bracket work on a 2017 Durango?
Not sure off hand sorry man
nice job , remember the 97-2003 camaros ? yeah those never had a good spot for the plate
Yea your right about that
What bolts did you use again. I want to do this on my 2013 SRT8
Does anybody know if it works for the Dodge Charger RT 2018 model?
Does this work with a 2018 scat pack? My grill looks different than yours.
Wonder if this will work on a 2014 Charger
as long as the bumper has those holes in it, it should fit, you may need to go with longer toggle bolts if anything but the process is the same.
hanksranger
Thanks
wheres the link to get the plate holder or is that what dodge supplies??
Ya it was in the trunk of the car
hanksranger How unfortunate are we that we live in a shitty 2 plate state?
hanksranger i purchased one , so dodge supplies one then , cause i just send it back!! save $20 bucks
Yeah but is not directly in the back your truck lift up the panel above the spare tire and It might be in there
I got that bumper mount at Pep Boys.
Where did you get the license plate holder?
it was in the back of the car when it was purchased
I was going to do this but I have that sensor thing. :( If I dont want my plate on the bumper I would have to offset it.
+Tamera Huckaba Im in the same boat. Can we offset it?
I’ll stick with it on the bumper cover, for it saves the front bumper.
where did you get the black mount? 0:30
Mine came with the car when I bought it. It was wrapped in plastic inside the trunk.