is it necessary to change the volume/power buttons and wireless charging coil from the damaged housing onto the new housing if the new housing already comes with them on?
By default I always remove LiDAR as well as the board/battery/rear camera/screen before I do back glass. As for your particular issue I’m not sure how to fix LiDAR or your particular situation
@@repaironwheels It's the original screen but I forgot to put back the last metal bracket, so I opened the Phone again and the glue for the screen kinda messed up. Should I remove the glue and try to close it without?
@Osmo97 if the bezel is siting higher on one side or the other you might have a screw stuck to the adhesive or a magnet on the speaker or Taptic Engine Realistically the phone is already not waterproof anymore so removing some or most of the gasket isn’t going to hurt. But I doubt that’s the problem
Very detailed explanation thank you. i can give some advise as i using ipa that will dry out my finger skin and my hand look same. wash it with soap dont use any cream as ipa will suck into skin. vitamin a,b,d,e is great if you can get also for nails. i dont like using gloves i sometime using flux and all the chemicals that is carcinogen. and my skin also get those..
I was thinking about doing this but i do not trust myself with all these little screws and parts. Also no heat gun. Idk what’s wrong with my phone. All i get is high temp warning after i dropped it and bent the frame a little.
@@repaironwheels that would be great but another thing is I don’t get any 5g while that warning is up. Would that mean my 5g antenna is damaged due to the frame bending or is that just due to the temp warning not allowing anything besides emergency calls
5130 I was handling the flash flex/bracket. And the proximity sensor is located on the screen. Can you elaborate a bit more on that part, I’m genuinely curious. I know that apple makes several different models of 12 pro max (A2342, A2410, A2411, and A2412) and there are inevitably small differences between the us version and others
The glue that binds the glass/oled to the bezel weakens over tome. On more than one occasion I’ve seen people damage their display using an iSclack or equivalent. It all depends on the application. If you need to reuse the screen stay away from suction. If you dont, have at it
@@repaironwheels thank you so much. It’s always sometimes a shame to see how big companies uses suction devices for their methods knowing the risk there is behind it.
@@repaironwheels your welcome!! I have the 12 pro max and it was rather interesting to see the insides of it. Is the repairability of the phone difficult?
Thank you for sharing high-quality maintenance knowledge with everyone. Upvote for you!
Much appreciated!
is it necessary to change the volume/power buttons and wireless charging coil from the damaged housing onto the new housing if the new housing already comes with them on?
It’s not a paired part so no
@@repaironwheels Thank you!
Thank you! About to replace mine, i already fix front for a 11 pro max about a year ago, let’s see how this one goes!
Break a leg
Always love watching your videos, very informative. Keep putting up these great videos.Thanks.
Thank you
Is this easier than using heat to break back glass and repair?
Id say so. It’s even easier if you get a housing with small parts installed
Do you have a URL for the replacement MagSafe magnets if they are not already in the housing?
www.mobilesentrix.com/wireless-charging-magnet-for-iphone-12-iphone-12-pro-iphone-12-pro-max
Perfect, thank you
Great video, & yes the rear glass replacement is a huge pain! Just do the should Back housing !
Thank you
That is most in depth demonstration how to repair a phone. Thank you so much for the teardown.
Here to serve
@@repaironwheels I am in the same line of business so I know that's the best teardown video. Again thank you.
Lidar sensor not working after backglass replacement and photos not saving.
By default I always remove LiDAR as well as the board/battery/rear camera/screen before I do back glass. As for your particular issue I’m not sure how to fix LiDAR or your particular situation
Where can I buy the back glass?? USA
Gngbuy.com
What did I wrong, if the pentalobe screws won't fit back in?
Are you using the original screen, and is it seated properly
@@repaironwheels It's the original screen but I forgot to put back the last metal bracket, so I opened the Phone again and the glue for the screen kinda messed up. Should I remove the glue and try to close it without?
@Osmo97 if the bezel is siting higher on one side or the other you might have a screw stuck to the adhesive or a magnet on the speaker or Taptic Engine
Realistically the phone is already not waterproof anymore so removing some or most of the gasket isn’t going to hurt. But I doubt that’s the problem
Pretty informative. However, I did not see it turning on. Although I would test the phone first before sticking the battery and sealing the screen!
I agree. Testing the functionality of the device prior to sealing it up is great advice. Normally I do. Not sure why I didn’t
Where can I buy the new housing?
Are you in the US
Very detailed explanation thank you.
i can give some advise as i using ipa that will dry out my finger skin and my hand look same. wash it with soap dont use any cream as ipa will suck into skin. vitamin a,b,d,e is great if you can get also for nails. i dont like using gloves i sometime using flux and all the chemicals that is carcinogen. and my skin also get those..
Thank you for the tips. Part of it is having a habit biting my nails and cuticles but I’ve gotten way better about since this video
@@repaironwheels thanks for the reply.
Awesome video, thanks for sharing with us!!
Here to serve. Thank you for watching
can you leave a URL for the back housing?
Mobilesentrix
I was thinking about doing this but i do not trust myself with all these little screws and parts. Also no heat gun. Idk what’s wrong with my phone. All i get is high temp warning after i dropped it and bent the frame a little.
To my knowledge high temp comes from the battery board being damaged somehow. If you are in the US I can swap both for around 300
Spencer@mobileiphonerepairsd.com
7609634948
@@repaironwheels that would be great but another thing is I don’t get any 5g while that warning is up. Would that mean my 5g antenna is damaged due to the frame bending or is that just due to the temp warning not allowing anything besides emergency calls
Can you call me It would probably be a lot easier than messaging back and forth
50:43 Attention European version do not have the so called "proximity sensor" in the phone. I lost half an hour thinking I lost the part.
5130 I was handling the flash flex/bracket. And the proximity sensor is located on the screen. Can you elaborate a bit more on that part, I’m genuinely curious. I know that apple makes several different models of 12 pro max (A2342, A2410, A2411, and A2412) and there are inevitably small differences between the us version and others
You not a fan of suction cups on the screen to aid in creating a gap?
The glue that binds the glass/oled to the bezel weakens over tome. On more than one occasion I’ve seen people damage their display using an iSclack or equivalent. It all depends on the application. If you need to reuse the screen stay away from suction. If you dont, have at it
91% or stronger iso makes the process a whole lot easier
iPhone 13 Pro screen removal - no heat necessary
ua-cam.com/video/WuwxhvCqFqE/v-deo.html
@@repaironwheels thank you so much. It’s always sometimes a shame to see how big companies uses suction devices for their methods knowing the risk there is behind it.
@@repaironwheels also, i understand no heat was the challenge but heat would of definitely helped so much more in that same combination?
Awesome video
Thank you for the kind words
@@repaironwheels your welcome!! I have the 12 pro max and it was rather interesting to see the insides of it. Is the repairability of the phone difficult?
thats a lot of work...
It gets easier the more you do it
If you'd rather not I'd be happy to for you
your first try housang chang.😀
What makes you think that
Tháo màn nứt mẹ rồi.. tháo stupid quá 😂
Sure thing buddy
Do you have Instagram
Repaironwheelssd