Eventually, I made a reasonable choice. But it was a build that I personally really liked. What's special and good about it is that this DIY electric board is the only one in the world and built for me only. If any of the subscribers are planning a DIY, I hope you will find some useful information during the build process. 결국 합리적인 선택을 했습니다. 하지만 개인적으로 너무 마음에드는 빌드였습니다. 확실히 특별하고 좋았던점은 이 DIY 전동보드가 세상에 하나뿐인 나만의 보드라는 점입니다. 구독자분들중 DIY를 계획하고 계신다면 빌드과정에서 유용한 정보가 있기를 바랍니다.
Cool looking board. By the way for 10S you really need to be using a higher kv motor (220-260kv) or run 12S. Low kv and low voltage is a bad combo. Also motor amps should be much higher, maybe 80A for those motors, then just restrict battery amps to maintain cooling and battery discharge current if needed ;)
Max motor must be set as specs of the motor. Battery current as the continue battery discharge (so in this case with 2 parallel connected batteries --> 60 Amps (2*30amp))
@@mayeurkim this is not true. The motor current is rated by continuous battery current not phase amps. You can set phase amps as high as you want basically. I'm running 165 phase amps on 12S with 6485 motors and its awesome
@@liam_evangelista it is pretty simple the max power of your board is defined by the discharge current of your battery and voltage. So in this case around 2700watt (60a*44.4v). The motors can have higher discharge but cannot have more power then 2700watt. For example if your motors are together 150amps, then till 18v (2700w/150a) they can have full discharge current but that lowers to 60amp at their highest speed/voltage.
@@mayeurkim that is true, however max motor amps can be set as high as you like as long as the vesc can handle it, for example 200A, but if you set 60 battery amps then the current coming from the battery will never exceed 60A, but the board will feel very punchy at low speeds. Motor amps is always higher because the controller uses pulse width modulation to reduce the effective voltage to the motor, so at low speeds even though the motor current might reach 100A, the voltage could be only 50% of battery voltage so for example: 100 motor amps @ 50% duty (say 21V) is 100A x 21V = 2100W then divide that by the actual battery voltage 42V gives you 50 amps on the battery side. I hope this makes sense. I have a lot of experience with this
@@liam_evangelista I have build also a lot of boards. I never exceed the motor Amps that are given by the manufacturer. I think when those motors are struggling and they go over their current limits, there is chance the coils could be burned. They will definitely get pretty hot when amp settings are set higher.
⚡ *The sequel that beats the original movie!* ⚡ Those cute little white baby motors 🤩 I still use 10S boards, no plans to get a 12S one yet 😂 It's like a cute little mini monster, a chihuahua, looks way smaller than 39" length cos of the beautiful design. I would love to ride a DIY like that 👌🏼 This is one of my favourites from all your builds!!
I loved the look of the failed version so I'm glam you remade it! A more portable version in the same style would be great (cuz this one is a T H I C K boy), love your builds!
That may prove a bit tricky. Smaller trucks could risk wheelbite, might have to add riser pads or cut into the nose/tail to compensate. As for the deck itself, shortest popsicle deck I could find is 29 inches. You could, again, cut the nose and tail down but then you'll lose some of that low profile you get from the concave. Point is: it's possible, but there are compromises involved
@@guitarwi3rdo thanks! But i was thinking of a configuration of the same kinda lenght, but less wide, ive never really done much e skating so I don’t know the compromises that come with it. Im pretty curious abt the reason that the trucks are so wide
Please, if you have time, make offroad like a Trampa, but there are front and rear lights so it can be used at night, thankyou. Greetings from Indonesia 🇮🇩
he has built some all terrain boards before. but I do like the idea of integrated lights. if Kami sees this, trying to build your own lighting into the next DIY would be a very cool touch.
No, you can't. This is because the BMS is separately installed in each battery pack. If there is only one charger, you should charge the other one after charging one.
Check this out~ ko.aliexpress.com/item/1005001275857939.html?spm=a2g0o.productlist.0.0.2e9365d9DSeJ8N&algo_pvid=6ef5d54e-3fd9-45cc-bb3d-3dd53584bcaa&algo_exp_id=6ef5d54e-3fd9-45cc-bb3d-3dd53584bcaa-0&pdp_ext_f=%7B%22sku_id%22%3A%2212000015555388921%22%7D&pdp_npi=2%40dis%21KRW%21%21237052.0%21%21%21%21%21%402101d8b516574792660121256ee219%2112000015555388921%21sea
Hye man, nice build. Thinking about building one for myself. I love seeing how responsive that truck. My question, did you use that riser pad on both truck?
@@KAMiJUINs thanks for the reply. I’m your new fan. I just recently get into this esk8 scene after getting my first board. I love the idea of customising my own board. I have old deck laying around which in good shape. Just stuck on deciding battery part. Which battery do you recommend for street board. Lipo or lithium ion?
Yeah, the battery's discharge(nearly 250A) rate was not enough, and the ESC had a total 200A max of output. The motors could each use a current of 160A, so both were poor choices
Eventually, I made a reasonable choice. But it was a build that I personally really liked. What's special and good about it is that this DIY electric board is the only one in the world and built for me only. If any of the subscribers are planning a DIY, I hope you will find some useful information during the build process.
결국 합리적인 선택을 했습니다. 하지만 개인적으로 너무 마음에드는 빌드였습니다. 확실히 특별하고 좋았던점은 이 DIY 전동보드가 세상에 하나뿐인 나만의 보드라는 점입니다. 구독자분들중 DIY를 계획하고 계신다면 빌드과정에서 유용한 정보가 있기를 바랍니다.
love your vids
Thank you so much~ :)
Another great DIY build, thanks for sharing!
i really love this build. have you plane to test it with offroad tire (6")? thanck you for this inspiration.
absolutely cracking build! the look of the board is just amazing
I wish to see another portable build with this style
Thank you for watching :) and someday~
One of the nicest boards I've seen
Thank you for watching :)
I know nothing about e-boards, but this was super interesting to watch!
Thank you for watching~ :)
Such an inspirational board, so creative🔥
Thank you for watching :)
Cool looking board. By the way for 10S you really need to be using a higher kv motor (220-260kv) or run 12S. Low kv and low voltage is a bad combo. Also motor amps should be much higher, maybe 80A for those motors, then just restrict battery amps to maintain cooling and battery discharge current if needed ;)
Max motor must be set as specs of the motor.
Battery current as the continue battery discharge (so in this case with 2 parallel connected batteries --> 60 Amps (2*30amp))
@@mayeurkim this is not true. The motor current is rated by continuous battery current not phase amps. You can set phase amps as high as you want basically. I'm running 165 phase amps on 12S with 6485 motors and its awesome
@@liam_evangelista it is pretty simple the max power of your board is defined by the discharge current of your battery and voltage. So in this case around 2700watt (60a*44.4v).
The motors can have higher discharge but cannot have more power then 2700watt. For example if your motors are together 150amps, then till 18v (2700w/150a) they can have full discharge current but that lowers to 60amp at their highest speed/voltage.
@@mayeurkim that is true, however max motor amps can be set as high as you like as long as the vesc can handle it, for example 200A, but if you set 60 battery amps then the current coming from the battery will never exceed 60A, but the board will feel very punchy at low speeds. Motor amps is always higher because the controller uses pulse width modulation to reduce the effective voltage to the motor, so at low speeds even though the motor current might reach 100A, the voltage could be only 50% of battery voltage so for example: 100 motor amps @ 50% duty (say 21V) is 100A x 21V = 2100W then divide that by the actual battery voltage 42V gives you 50 amps on the battery side.
I hope this makes sense. I have a lot of experience with this
@@liam_evangelista I have build also a lot of boards.
I never exceed the motor Amps that are given by the manufacturer. I think when those motors are struggling and they go over their current limits, there is chance the coils could be burned. They will definitely get pretty hot when amp settings are set higher.
⚡ *The sequel that beats the original movie!* ⚡
Those cute little white baby motors 🤩
I still use 10S boards, no plans to get a 12S one yet 😂
It's like a cute little mini monster, a chihuahua, looks way smaller than 39" length cos of the beautiful design.
I would love to ride a DIY like that 👌🏼
This is one of my favourites from all your builds!!
I love your comment~ Brother :)
You know I'm always grateful, right? HaHa~
@@KAMiJUINs I'm grateful for these amazin videos!
항상 많은 도움이 되는 영상 감사합니다.
이번 보드는 정말 멋집니다ㅋㅋ
하~ 도움 되셨다니 기쁩니다~ :) 항상시청해주셔서 감사합니다!!!
Wow! Amazing build. Awesome video and bangin' soundtrack! 10/10 👍🏻
Thank you so much~ :)
Shame those bigger motors didn't work, hopefully you find a pair that does. These pop deck esk8s you've built have inspired me to make some of my own
Thank you for watching ~
Wooooooooooow New creation❤️
Thank you for watching :)
Awesome build!
Thank you for watching :)
I loved the look of the failed version so I'm glam you remade it! A more portable version in the same style would be great (cuz this one is a T H I C K boy), love your builds!
That may prove a bit tricky. Smaller trucks could risk wheelbite, might have to add riser pads or cut into the nose/tail to compensate. As for the deck itself, shortest popsicle deck I could find is 29 inches. You could, again, cut the nose and tail down but then you'll lose some of that low profile you get from the concave.
Point is: it's possible, but there are compromises involved
@@guitarwi3rdo thanks! But i was thinking of a configuration of the same kinda lenght, but less wide, ive never really done much e skating so I don’t know the compromises that come with it. Im pretty curious abt the reason that the trucks are so wide
As I said, my favorite Esk8 Content creator 🙌🏼 You should be esk8 therapy 😆
Thank you so~~~much for saying that :) HaHa
Thank you for posting this video!
Thank you for watching too~ :)
It's good you can go back to rebuild boards. This is something I do happily
Thanks bro :)
I wonder, do you have some sort of design speciality? You have developed quite nice style for your builds. Keep going!
Thank you so much and thank you for watching too ~ :)
Please, if you have time, make offroad like a Trampa, but there are front and rear lights so it can be used at night, thankyou. Greetings from Indonesia 🇮🇩
he has built some all terrain boards before. but I do like the idea of integrated lights. if Kami sees this, trying to build your own lighting into the next DIY would be a very cool touch.
Amazing job and super informative KAMi JUINs!! loved it!
Thank you so much, brother~ :)
Good video bro Amazing !!!😊👍
Thank you so much, bro :)
이번 보드는 진짜 역대급이네요 ㄷㄷ
시중에 나온다면 구매하고싶어욬ㅋㅋㅋㅋㅋㅋㅋ
아 그렇게 봐주셨다니 감사합니다~ :)
디자인적인 센스도 너무 좋으시네요
저도 꼭 빌드 하나 해보고싶어서 영상 열심히 보고있습니다 ㅋㅋ
매번 힐링 영상 감사합니다 ㅎㅎ
네 시청 감사합니다~ :)
개인적으로 이거 파시고 살수있음 사고싶네요 뭔가 f1레이크카 느낌의 빌드인거 같아요 광폭 휠과 타이어 그리고 더블데크?라고 해야하나 나무판이 배터리 위 아래로 있으니 더 튼튼할꺼 같네요
그렇게 봐주셔서 감사합니다. DIY로 시도해보세요. 조금만 알아보신다면 그리 어렵지않게 만드실수 있을거에요 :)
I neeedddddd thoseee Wheels
Just try~ :) Thank you for watching
I love so much this board...!!!😍😍
I think i will build an e-skateboard...🤔 And the main reason is you....😄🙏
HAHA Thank you for watching ~:) Hope you doing well as you want~
nice build mate
Thank you so much, brother :)
lovely channel & kami 💗
Thank you so x 1000 much :)
Great Vid!
Thank you so much~
Beautiful build and craftsmanship, how innovative. Only thing I don’t get is why are you wearing a mask?
Thank you for watching ~ and I have rhinitis :(
Can you charge it with one charger only while the batteries discharge wires are connected in parallel?
No, you can't. This is because the BMS is separately installed in each battery pack. If there is only one charger, you should charge the other one after charging one.
@@KAMiJUINs thank you bro
where did you buy those massive 70120 motors???
Check this out~
ko.aliexpress.com/item/1005001275857939.html?spm=a2g0o.productlist.0.0.2e9365d9DSeJ8N&algo_pvid=6ef5d54e-3fd9-45cc-bb3d-3dd53584bcaa&algo_exp_id=6ef5d54e-3fd9-45cc-bb3d-3dd53584bcaa-0&pdp_ext_f=%7B%22sku_id%22%3A%2212000015555388921%22%7D&pdp_npi=2%40dis%21KRW%21%21237052.0%21%21%21%21%21%402101d8b516574792660121256ee219%2112000015555388921%21sea
Dope! How many boards have you built in total?
Hye man, nice build. Thinking about building one for myself. I love seeing how responsive that truck. My question, did you use that riser pad on both truck?
Thank you for watching :) Yeah, I use the riser pad both side
@@KAMiJUINs thanks for the reply. I’m your new fan. I just recently get into this esk8 scene after getting my first board. I love the idea of customising my own board. I have old deck laying around which in good shape. Just stuck on deciding battery part. Which battery do you recommend for street board. Lipo or lithium ion?
100% = Lithium ion
Nice build! What type of rubber sheet for the enclosure?
A rubber plate 5mm thick was used
fire vid
Thank you for watching :)
When board tern or stearing motor running same speed or difference speed.
Thwy have to turn at different speeds to turn. It's like how a cars differential works
Good job😄
Thank you brother~ :)
Your amazing man! Question, i have a gtr carbon and i want to change it a singLe kingpin trucks, what shouLd i buy? Thank you! Godspeed
Thanks and check this out ~
flipsky.net/collections/trucks/products/flipsky-16-3-cnc-new-upgrade-rkp-trucks-for-diy-electric-skateboard-longboard-esk8
Thank you so much!
good your last battery pack was to light needed way more amps than a rc battery can provide i also use 2, 30 amps in parallels
Yeah, the battery's discharge(nearly 250A) rate was not enough, and the ESC had a total 200A max of output.
The motors could each use a current of 160A, so both were poor choices
Is this the jacket with the armor inside of it? Can someone tell me the name?
lazyrolling.com/products/armored-hoodie-by-lazyrolling
check this out~
@@KAMiJUINs thank you! Love your content
Love that strip for a handle, where did you get it?
Thanks!
You can google it "poly webbing tape"
Thank you for watching~
love your channel
also first
Where do you get those 15 degree riser pads from?
www.sk8kings.com/khiro-angled-wedge-rail-riser-pair-2-pieces.html
check this out~
What are you gonna do with the rc motors?
It was judged that the sensorless motor was unstable :(
Thank you for watching
여전히 이런걸 어떻게 다 아시는건지 신기하고 궁금하다
필요한것이나 모르는것은 유튜브나 구글을 찾아보고있습니다.
시청감사합니다~
where can i get that red nylon loop?
Search "Poly Webbing Tape" on Amazon~
@@KAMiJUINs Thank you! Love the build!
Nice Build.What is the advantage of having double wheels?
Thank you for watching :) and the traction and grip are good and it looks much more special lol... But the battery runs out faster.
how can i buy it?
It's not for sell... Sorry~
think an encoder is needed to run this innrunners on vesc based setups
KR nice build
Thank you for watching ~
first
i disliked. you cant find pavement like that......... your riding on a racetrack
I dislike you..... I can't find a race track near around~ HaHa :)
Thank you for watching~