Being an enthusiast and not a professional in the paint world, I absolutely love the more economical equipment videos… the pros may not agree but I like the videos that show a professional result with an affordable tool!
I got 50 litre compressor, has 14cfm. Should I use slg5(9.8 cfm) or f160(7.7cfm) because video says flg5 is more suitable for home use even though has high cfm requirements
@ysr789 the cfm rating on the ANI guns is misleading. They rate them at lower PSI, but they don't atomize all until you crank the pressure up. The FLG5 keeps composure from 18-29, but can handle up to 35 without blowing out the fan pattern. It's also pretty efficient on paint use. The ANI isn't
Bought an FLG5 in the U.K. on the strength of this video. I’m a hobbyist but like to make a decent job. Did a base and clear red side skirt this morning to try it, really even spray pattern and the clear went on like glass 👌
I did a home crash repair and spray job and am happy with the result. Thanks Gunny for the time you put into the channel, without it, I probably wouldn't have tried. The one lesson I hadn't learnt was how far to pull down and clean my gun (Ani150). I was taking the pot, Air cap, needle, spring and knob out to clean separately and then reassemble, flush and test spray gun cleaner. But I didn't realise that the air nozzle itself needs to be spanner'd out to clean the chamber behind it as well. The supplied instructions were an exploded diagram and parts list and most utube's show just the "hand screw out" items being cleaned. Its a detail that might have been obvious to everyone else, but I missed it.
@@sean7193 what are you spraying? Base, clear, or single stage? I’ve used both for all 3 and for me, the F160 works fine for single stage and base, the FLG5 works fine for clear and base. The F160 seems to need a bit more pressure than the FLG5, but I’ve heard it both ways. The ANI guns are also a bit easier for me to clean, but I’m just strange in how I clean my guns.
@@aurktman1106 thanks for getting back. I plan on spraying base and clear with it (got the 1.3) . From what I hear you can reduce the material, and narrow the fan slightly if you want to reduce the pressure required by the f160. I'm.sure with a little playing around I'll get it to work for my scenario....also do you k ow of you can spary epoxy sealer with it or should I get a dedicated primer gun for that? Like a 1.8?
@@sean7193 depends on the epoxy primer. The epoxy I use needs the smaller tip. I use the 1.3 or I use the big pot on my ANI R150 to spray epoxy. It has the 1.0 tip.
Hey gunny here’s a video idea LPH400 vs supernova. Lph400 always made think it was the working mans supernova and the supernova was like a pimped out rockstar version of the lph400 but I only have an lph400 so I’ve never been able to compare them. Anyways I would love to see your professional opinion. Spray on bro
Oh and to the original comment i had both lph400 and supernova the lph400 is way better i traded my supernova in on another lph400 in just a few weeks.
I have gone from diy on my own cars to "semi-pro/minor league" taking on projects for others. I love making something old look nice again. In addition to books and just getting out and painting stuff, I watch hours of paint video in the evening when i'm done working. So thanks for all the videos and motivation
Also have a FLG5 recommended by gunny, more than good enough for my skill, painted my 180sx & came out pretty sick could not be happier with my purchase 🙂👍
Another great video 👍 i have all 3 of them, flg5 1.8 for primer work, AZ3 1.3 for basic base jobs and ANI R160q 1.0 for small stuff all good guns for the price but cant beat the higher end guns
Another video idea: show us how a good clear sprays vs a cheap one and show us how they each spray through say a budget gun vs a pro gun. redo video idea for primer, base, sealer. It would be cool to know what you look for in a quality product. Also straight up safety tips episode or series. Honestly with all the chemicals that come with this job/hobby I’m sure you’ve came up with some genius ideas on keeping yourself safe that would benefit us newbooties. Keep up the good work
Great comparison video I think you summed them up very objectively. I’ve been contemplating buying the ANI F160 in a 1.9 to replace my AZ3 as a primer gun, I’m just really disappointed in the AZ 3 which sucks because I do generally like Iwata’s
I bought the ani r150 based on your reviews and I loved it. After 2.5 years It needed a rebuild as the tiny white o ring behind the nozzle keeps moving. If ani simply offered support [maybe videos on how to do this] they could make a viable product even with their current quality.
Look at the Spray guns direct website. They probably sell the seals in a 5 pack for cheap. Parts are listed in the section with the gun you look up. And I've seen Gunny show this seal in one of his videos,too.
Hello from Canada! I own the FLG5 gun and need to change out the Seals in it. I do have a kit to fix it. Would you be willing to do a Seal replacement Video???? It would be greatly appreciated.
Devilbiss Gravity Spray Gun, 0.059In/1.5mm - FLG-CNG-115 vs Iwa-9276? This are my choices at the moment because I can't ship here the flg-5. I just need the gun for my welding projects(doors, furniture, gates, etc) business signs, and a few car parts
I have the gunsa 2.0 and flg5 1.4, diy occasional use, reliable, flg5 can be dialed down to paint small pieces and I’ve ran nearly everything through it. BOND out 🕵🏻♂️🍸0️⃣0️⃣7️⃣
Hey Gunny, MAN, YES I BOUGHT THAT ANI 170 SILVER AND LOVE It. I AM CONFUSED THOUGH ON SPEAY GUNS DIRECT WHICH 3M PPS ADAPTOR TO GET PLEASE ADVISE..forgive the caps just excited bro...next is the FLG5, THE PANELS I usually spray are motorcycle fairings that I build, mostly fiber glass requires painting or primer/ CARBON FIBER, USUALLY CLEAR ONLY AND MAYBE SOME GRAPHICS.. YOU REPLY WOULD BE AWESOME BRO.....THANKS A MILLION, I LOVE ANYTHING YOU DO... AS A MATTER OF FACT YOUR CHANNEL TAUGHT ME HOW TO SHOOT.....WISH I COULD SHOW YA SOME SOME OF THE WORK...!!
Gunny... you swear by DeVilbiss....Ryan Evans {Counts Customs} swears by Iwata! Who is the better painter? Ryan Evans... HANDS DOWN! But I love you too man!
I’d be interested to know your opinion on the Star S106 1.4mm. These guns are available from most of the big tool shops in Australia (Total tools, Sydney tools etc) for $190, being so readily available it’s more likely the type of gun a beginner/hobbiest would pick up.
Good review Gunny, I got both my FLG5 guns a year or so back after watching your vids on them and have to say they lay down primer, WOW and base just fine, these days they are just used for primer and WOW (sealer) as my GTI Pro is my base gun, after using the DV1S I've got myself a DV1 C1 clear gun which arrived today so looking forward to tying this out 😎👍 John UK.
Hey gunny, I watched your all videos, you doing very good job. I just want to ask you that, what psi should be set for basecoat solid paint (paint+hardner) where no clear need ? What distance should be from panel to gun ? How many turns of fuid ? Specially for devilbiss gti pro ? I would be very thankful if you would reply Thanks
@@TheGunmanChannel The only thing I've ever painted are 1 set of wheels. I used my FLG5 to primer first but then I realised I needed a highbuild to fill in the dips on my flaking chrome wheels so I bought the AZ3, I didn't want to use highbuild in my paint gun. But I did like the way the AZ3 sprayed the primer when I did a re prime after sanding through in some spots. The feel in hand and less weight is what I really like about the AZ3, I'm sure the FLG5 would have sprayed more like the AZ3 if it had a 1.8 tip. The guns are way overkill for me but I like your channel so I wanted something you would recommend. I also got roughly 2meters length of clear urethane hose I conect to my 20 meter main airline for better control and a water seperator between them. I remember one of your videos talking about waiting time between coats, and realised how important that was when doing my wheels.. So I sanded and repainted them to fix the runs :P
I’ve been trying to compare these for a couple days. I’m super glad you did this. Thanx from Los Angeles CA. USA. We should make a Gunman Krew btw🤘😎 spray guns and heavy metal 🎸 hah
My old boss use to come out of the office after the painters went home and always sprayed polly undercoat and left the gun and had a brand new $200 star instead of cleaning it out it went in the bin 😳 office people stick to your paper and pen
You're starting to confuse me, another video U did on cheap gun's U say the flg5 is the best & you use it alot. In this video U say the ani 160 is the best & the flg5 is good for at home
Gunny why do you use the pressure so high ?, I speak for the ani f160 just know the trick and you can lower the pressure a little bit and close the fan a little from half to one turn and close the material a little and can spray at 2 bar max 2.5 bar without problems also lowering the overspray because at that pressure it makes too much cloud for someone who uses it in the garage or do it yourself and does not have the right suction cannot work with these parameters
I will have four cars to paint over the next three years. Given paint and spray booth hire is expensive, is it worth trying to economize with an FLG5 or should spend the extra and just buy the Prolite with a TE20 and 1.3mm?
I LOVE my Prolites. Scaled back to a 1.2 fluid tip and a TE10 air cap for both base and clear. Nice even flat finishes. Have an FLG3 and FLG4 and much harder to get a good flat finish- the Prolite is a dream come true and worth the extra bucks which you save in sanding and buffing time!
Good evening friend, your videos are very good, I want to ask you a question, I am about to buy one of these two pistols, Devilbiss FLG5, or Anest Iwata AZ3HT2, both 1.8, I will use it for white primer,
Awesome video gunny, its great to hear the different views and benefits of each gun for different purposes, and doing entry level guns is awesome, this is probably the sweet spot for your viewers watching, can we have a mid range gun test soon, good, better best, would be awesome, thanks again from rAdelaide :-)
hey gunman a part of the video you said cheap callenger clear coat, i been spraying axalta challenger clear, what is your perspective on the clear? i realize the clear like to die back and shrink a lot have you had similar issue? gloss is okay but seem to shrink more than others
If that's the case I'm very surprised. I use the ani at 45psi so I guess I just assumed it would need more CFM. But I still wouldn't use the ANi at home because the excess pressure required makes a lot of overspray
Ola Atirador! Essa arma FLG DeVilbiss FLG5 FLG-G5 preferencialmente bico 1.4 não vende aqui no Brasil, como faria para adquirir uma arma dessa aí? Vc tem loja para venda? Sou seguidor do seu canal a muito tempo e admiro demais seu trabalho perfeito e muito obrigado pelas dicas de sempre....
Have you ever had a gun grow on you, like when you 1st used it and you were like this gun is rubbish and then the more you use it its like you know what this gun isn't that bad😅😂
FlG 5 nice gun but no parts if it goes wrong. Mine needed a new Spreader valve. Contacted Devilbiss who confirmed no part available. Budget gun they said so basically throw away if it goes wrong. Very disappointed.
The presence of the three pistols is good. But you are very lazy and repeat the same things over and over again. Many words are unnecessary. Few and specific descriptions.
Being an enthusiast and not a professional in the paint world, I absolutely love the more economical equipment videos… the pros may not agree but I like the videos that show a professional result with an affordable tool!
I got 50 litre compressor, has 14cfm. Should I use slg5(9.8 cfm) or f160(7.7cfm) because video says flg5 is more suitable for home use even though has high cfm requirements
@ysr789 the cfm rating on the ANI guns is misleading. They rate them at lower PSI, but they don't atomize all until you crank the pressure up. The FLG5 keeps composure from 18-29, but can handle up to 35 without blowing out the fan pattern. It's also pretty efficient on paint use. The ANI isn't
Bought an FLG5 in the U.K. on the strength of this video. I’m a hobbyist but like to make a decent job. Did a base and clear red side skirt this morning to try it, really even spray pattern and the clear went on like glass 👌
I did a home crash repair and spray job and am happy with the result. Thanks Gunny for the time you put into the channel, without it, I probably wouldn't have tried. The one lesson I hadn't learnt was how far to pull down and clean my gun (Ani150). I was taking the pot, Air cap, needle, spring and knob out to clean separately and then reassemble, flush and test spray gun cleaner. But I didn't realise that the air nozzle itself needs to be spanner'd out to clean the chamber behind it as well. The supplied instructions were an exploded diagram and parts list and most utube's show just the "hand screw out" items being cleaned. Its a detail that might have been obvious to everyone else, but I missed it.
Just ordered FLG 5. Thanks for all your hard work and great information.
Great gun, I love it.
Does it only have the 1,4mm nozzle?
@@jones_1996 there is 1,3 and 1,8 also.
m.facebook.com/story.php?story_fbid=479528773414950&id=105117464189418
@@SLYDIT great job!
I have the F160, R150, and FLG5 all on your recommendation and I must say I’m absolutely satisfied!
I just got the f160, but now sounds like the flg5 is also good to have...which one do you prefer? should I just stick with the f160? thanks :)
@@sean7193 what are you spraying? Base, clear, or single stage? I’ve used both for all 3 and for me, the F160 works fine for single stage and base, the FLG5 works fine for clear and base. The F160 seems to need a bit more pressure than the FLG5, but I’ve heard it both ways. The ANI guns are also a bit easier for me to clean, but I’m just strange in how I clean my guns.
@@aurktman1106 thanks for getting back. I plan on spraying base and clear with it (got the 1.3) . From what I hear you can reduce the material, and narrow the fan slightly if you want to reduce the pressure required by the f160. I'm.sure with a little playing around I'll get it to work for my scenario....also do you k ow of you can spary epoxy sealer with it or should I get a dedicated primer gun for that? Like a 1.8?
@@sean7193 depends on the epoxy primer. The epoxy I use needs the smaller tip. I use the 1.3 or I use the big pot on my ANI R150 to spray epoxy. It has the 1.0 tip.
@@aurktman1106 gotcha. I was told to maybe use a different cheaper spray gun as the epoxy is hard on the tip.
Hey gunny here’s a video idea LPH400 vs supernova. Lph400 always made think it was the working mans supernova and the supernova was like a pimped out rockstar version of the lph400 but I only have an lph400 so I’ve never been able to compare them. Anyways I would love to see your professional opinion. Spray on bro
You will never find a better gun than the LPH 400... Period!
@@ronaldpeterson1538 until you spray a new wet on wet base system you will never find a better gun.. there i fixed it for you.
Oh and to the original comment i had both lph400 and supernova the lph400 is way better i traded my supernova in on another lph400 in just a few weeks.
I have gone from diy on my own cars to "semi-pro/minor league" taking on projects for others. I love making something old look nice again. In addition to books and just getting out and painting stuff, I watch hours of paint video in the evening when i'm done working. So thanks for all the videos and motivation
recommend Iwata's raven will be there Yes, spray lacquer, small work, KATANA-13C
A3z
W101
Which one is the most suitable
I have sprayed my car in acrylic with my FLG5, no problems, agree it's a great DUI gun.
20 year vet painter Nothing but sata for me. Iwata are water guns. Would make good trim out or primer guns
Also have a FLG5 recommended by gunny, more than good enough for my skill, painted my 180sx & came out pretty sick could not be happier with my purchase 🙂👍
Another great video 👍 i have all 3 of them, flg5 1.8 for primer work, AZ3 1.3 for basic base jobs and ANI R160q 1.0 for small stuff all good guns for the price but cant beat the higher end guns
Thanks Gunny, glad to see the FLG5 you turned me on to still ranks high on your list.
This helped as these were the guns I was considering for home. Thanks! 😎👍
Another video idea: show us how a good clear sprays vs a cheap one and show us how they each spray through say a budget gun vs a pro gun. redo video idea for primer, base, sealer. It would be cool to know what you look for in a quality product. Also straight up safety tips episode or series. Honestly with all the chemicals that come with this job/hobby I’m sure you’ve came up with some genius ideas on keeping yourself safe that would benefit us newbooties. Keep up the good work
Great comparison video I think you summed them up very objectively. I’ve been contemplating buying the ANI F160 in a 1.9 to replace my AZ3 as a primer gun, I’m just really disappointed in the AZ 3 which sucks because I do generally like Iwata’s
I have a F160 and love it! I haven’t used it a ton, but it’s been great every time I use it.
I've seen it used in a few videos and I think it's strong point is good atomization, I think I'll be getting one as soon as I'm able to
Nice to see your video again. Thanks Gunny.
Vinesh from Edmonton, Alberta, Canada
Thank you for all your videos. Great information. Thank you from Texas
I bought the ani r150 based on your reviews and I loved it. After 2.5 years It needed a rebuild as the tiny white o ring behind the nozzle keeps moving. If ani simply offered support [maybe videos on how to do this] they could make a viable product even with their current quality.
Look at the Spray guns direct website. They probably sell the seals in a 5 pack for cheap. Parts are listed in the section with the gun you look up. And I've seen Gunny show this seal in one of his videos,too.
Bought an f160 on your recommendation.
Went ahead and ordered a FLG 5. Arrived today.
Top man helped me out today of making quite a few decisions without spending hours reading
Hello from Canada!
I own the FLG5 gun and need to change out the Seals in it. I do have a kit to fix it. Would you be willing to do a Seal replacement Video????
It would be greatly appreciated.
I like the Flg5. I love the Bellaria. They will have to pry the GPI from my cold dead hands ! 😁👍
Devilbiss Gravity Spray Gun, 0.059In/1.5mm - FLG-CNG-115 vs Iwa-9276? This are my choices at the moment because I can't ship here the flg-5. I just need the gun for my welding projects(doors, furniture, gates, etc) business signs, and a few car parts
flg is underrated gun..i'm gonna buy it..
I have the gunsa 2.0 and flg5 1.4, diy occasional use, reliable, flg5 can be dialed down to paint small pieces and I’ve ran nearly everything through it.
BOND out
🕵🏻♂️🍸0️⃣0️⃣7️⃣
Hey Gunny, MAN, YES I BOUGHT THAT ANI 170 SILVER AND LOVE It. I AM CONFUSED THOUGH ON SPEAY GUNS DIRECT WHICH 3M PPS ADAPTOR TO GET PLEASE ADVISE..forgive the caps just excited bro...next is the FLG5, THE PANELS I usually spray are motorcycle fairings that I build, mostly fiber glass requires painting or primer/ CARBON FIBER, USUALLY CLEAR ONLY AND MAYBE SOME GRAPHICS..
YOU REPLY WOULD BE AWESOME BRO.....THANKS A MILLION, I LOVE ANYTHING YOU DO...
AS A MATTER OF FACT YOUR CHANNEL TAUGHT ME HOW TO SHOOT.....WISH I COULD SHOW YA SOME SOME OF THE WORK...!!
Gunny... you swear by DeVilbiss....Ryan Evans {Counts Customs} swears by Iwata! Who is the better painter? Ryan Evans... HANDS DOWN! But I love you too man!
It's not a competition
Just bought the flg5 few weeks ago ..cheap spray gun for £100
Hola amigo consulta cual de estas 3 pistolas recomiendas para usar imprimacion 2k en un automovil ?
I’d be interested to know your opinion on the Star S106 1.4mm. These guns are available from most of the big tool shops in Australia (Total tools, Sydney tools etc) for $190, being so readily available it’s more likely the type of gun a beginner/hobbiest would pick up.
Great video as always gunny.
Another great video giving people budget guns that are really good for the money plus i love watching your videos
Cheers Gunny, excellent finish on the last part, if my job comes out half as good I'll be stoked....👍
Do me proud mate!! That gun is going back to WA 🤣
@@TheGunmanChannel I've got another HQ wagon to do and a mustang waiting after my van, it'll be well used..👍
I picked up an airgunza 1.8 for primer and was terribly dissatisfied with the fan and overall performance
I'll take my prolite any day of the week
CAN YOU SHOOT BASE AND CLEAR WITH FLG5 1.3 TIP
Look for Gunny's video where he did just that.
Which gun would u recommend for a home garage with the odd use?
His Back 🏆
Good review Gunny, I got both my FLG5 guns a year or so back after watching your vids on them and have to say they lay down primer, WOW and base just fine, these days they are just used for primer and WOW (sealer) as my GTI Pro is my base gun, after using the DV1S I've got myself a DV1 C1 clear gun which arrived today so looking forward to tying this out 😎👍 John UK.
Hey gunny, I watched your all videos, you doing very good job.
I just want to ask you that, what psi should be set for basecoat solid paint (paint+hardner) where no clear need ?
What distance should be from panel to gun ? How many turns of fuid ?
Specially for devilbiss gti pro ?
I would be very thankful if you would reply
Thanks
i have an FLG5 1.3 and AZ3 1.8 I like the AZ3 feel more
Do you agree the AZ3 has a bit of a small fan for the larger panels?
@@TheGunmanChannel The only thing I've ever painted are 1 set of wheels. I used my FLG5 to primer first but then I realised I needed a highbuild to fill in the dips on my flaking chrome wheels so I bought the AZ3, I didn't want to use highbuild in my paint gun. But I did like the way the AZ3 sprayed the primer when I did a re prime after sanding through in some spots.
The feel in hand and less weight is what I really like about the AZ3, I'm sure the FLG5 would have sprayed more like the AZ3 if it had a 1.8 tip.
The guns are way overkill for me but I like your channel so I wanted something you would recommend.
I also got roughly 2meters length of clear urethane hose I conect to my 20 meter main airline for better control and a water seperator between them.
I remember one of your videos talking about waiting time between coats, and realised how important that was when doing my wheels.. So I sanded and repainted them to fix the runs :P
I’ve been trying to compare these for a couple days. I’m super glad you did this. Thanx from Los Angeles CA. USA. We should make a Gunman Krew btw🤘😎 spray guns and heavy metal 🎸 hah
My old boss use to come out of the office after the painters went home and always sprayed polly undercoat and left the gun and had a brand new $200 star instead of cleaning it out it went in the bin 😳 office people stick to your paper and pen
Gunman can you please do a video for painting upside down like undercarriage. Is it better to use a suction gun?
You’re better off using a separate pressure pot so you can twist the gun in any direction.
tell me whts the paint brand and clear coat you are using.looks shinny
You're starting to confuse me, another video U did on cheap gun's U say the flg5 is the best & you use it alot. In this video U say the ani 160 is the best & the flg5 is good for at home
Gunny why do you use the pressure so high ?, I speak for the ani f160 just know the trick and you can lower the pressure a little bit and close the fan a little from half to one turn and close the material a little and can spray at 2 bar max 2.5 bar without problems also lowering the overspray because at that pressure it makes too much cloud for someone who uses it in the garage or do it yourself and does not have the right suction cannot work with these parameters
I just got the f160 and plan to use it at home...good idea.
I will have four cars to paint over the next three years. Given paint and spray booth hire is expensive, is it worth trying to economize with an FLG5 or should spend the extra and just buy the Prolite with a TE20 and 1.3mm?
I LOVE my Prolites. Scaled back to a 1.2 fluid tip and a TE10 air cap for both base and clear. Nice even flat finishes. Have an FLG3 and FLG4 and much harder to get a good flat finish- the Prolite is a dream come true and worth the extra bucks which you save in sanding and buffing time!
Good evening friend, your videos are very good, I want to ask you a question, I am about to buy one of these two pistols, Devilbiss FLG5, or Anest Iwata AZ3HT2, both 1.8, I will use it for white primer,
FLG5 would be the better gun.
what do you think of europro HE or Anest Iwata Kiwami 4
I have an Iwatta W400 non bellaria that I bought new for $200. I don't think you could possibly do better for the money
Same but they went up in price like 350
@@Kaabosurron The Bellaria is 350 the W400 is 217 right now on amazon
@@paulhopkins1905 oh yea but the balleria was at 230 like a few months ago when I bought it
@@Kaabosurron damn, thats a steal
Love your videos mate…I live in Perth and would love to know we’re you work. As I am currently looking for a respray of my s13 and love your work??
Awesome video gunny, its great to hear the different views and benefits of each gun for different purposes,
and doing entry level guns is awesome, this is probably the sweet spot for your viewers watching,
can we have a mid range gun test soon, good, better best, would be awesome,
thanks again from rAdelaide :-)
Who wins in your opinion? Can you write in order first second third
hey gunman a part of the video you said cheap callenger clear coat, i been spraying axalta challenger clear, what is your perspective on the clear? i realize the clear like to die back and shrink a lot have you had similar issue? gloss is okay but seem to shrink more than others
What clears do you consider high end ?
What is your thoughts on the new iwata wider 4?
Flg5 requires 9.8cfm whereas ani f160 requires only 7.7 . So shouldn’t f160 be more suitable for smaller compressors
If that's the case I'm very surprised. I use the ani at 45psi so I guess I just assumed it would need more CFM. But I still wouldn't use the ANi at home because the excess pressure required makes a lot of overspray
Nice
Good one mate...from Kiwi
THIS KIWI IS GOING TO GET ONE
@@fredjones1238 I have the ANI great gun
Ola Atirador! Essa arma FLG DeVilbiss FLG5 FLG-G5 preferencialmente bico 1.4 não vende aqui no Brasil, como faria para adquirir uma arma dessa aí? Vc tem loja para venda? Sou seguidor do seu canal a muito tempo e admiro demais seu trabalho perfeito e muito obrigado pelas dicas de sempre....
Have you ever had a gun grow on you, like when you 1st used it and you were like this gun is rubbish and then the more you use it its like you know what this gun isn't that bad😅😂
That happened with the Supernova, partly because it's a prick to set up.
@@TheGunmanChannel 😂
I got the FLG 5 on your recommendation, and have not been disappointed. Could you possibly compair the FLG 5 to the FLG 693.
They are literally the same gun. Just different name depending on which state you buy them from
@@MrBigwilk yeah same gun different air caps
Secondo me il miglior ventaglio è quello Ani concordi?
What is the paint thickness guage you use to measure paint thickness?
Hi! Teste Anest Iwata Kieami4.👍
Hello Gunman , what is the part number for the PPS adapter that you have for the ANI 160 spray gun
S15 PPS2 adaptor or 15 for the original PPS
@@TheGunmanChannel thank you
Что лучше купить,flg5 или pro lait t110?
Get out there and paint something, and do it well.
I think that is going to be my phrase.
FLG5 1.3..shoplink sir..share..tx..
When you say the Ani 160 failed, what actually fails?
I couldn't even say, one just stopped working. I think it was the air valve.
Man this is killing me trying to find a flg5 or a ANI F160 in the USA.. any help will be appreciated
Spraygunsdirect.com in UK. Order on Monday and have it easily by Thursday. Mention Gunman for a free cleaning kit! They are blazing fast.
Very good job I like it ❤❤❤❤❤❤❤❤❤❤❤❤❤❤ thank you
Ani f160 1,3 or Iwata w400 bellaria 1,3 for base and clearcoat guys? Which is better and why? Can anyone help
what did you buy
@@pedoubek I bought the F160 and I'm very happy with it. I'll buy the Iwata bellaria for Clearcoat and use F160 only for Basecoat
My pic....ANI...F160
Got the flg, painted some shit an it's all 👍
Klass👌
Neden bu flg tanitiyorsun surekli.bu alt model bir tabanca ve cok iyi degil
You need to leave the gun make on the videos longer as we are trying to listen to you then having to backtrack hoping to find the on video comments
Thank you for this budget spray gun shoot out - that helps me make a decision.
FlG 5 nice gun but no parts if it goes wrong. Mine needed a new Spreader valve. Contacted Devilbiss who confirmed no part available. Budget gun they said so basically throw away if it goes wrong. Very disappointed.
Good shootout gunny 👍🏻
👍
Not surprising the Air Gunza didn't fare well, you are using an older model. I'm certain there are body shop range models now, ie blue flash
Ani 160👍👍👍👍👍
Has anyone tried the atom x16 hvlp mini?
ෆ්ප්ප්ප්ඩ්ඩ්
The presence of the three pistols is good.
But you are very lazy and repeat the same things over and over again.
Many words are unnecessary. Few and specific descriptions.