Taking Apart a Hole Saw

You can now support our channel! Learn more
www.simpleground.com/supportus...
In this video, I demonstrate how to replace the saw head on a hole saw. Just a simple video for anyone who hasn't tried it before.
Be sure check out our other content.
Website: www.simpleground.com
Patreon: www.patreon.com/simpleground
Instagram: simplegroundjourney
Pinterest: www.pinterest.com/simpleground/

[@lisaknox8975]

This just saved me from being without water for another weekend! Thank you so much! 🙌🏾💧

[@Simplegroundlife]

I'm glad you could find what you were looking for.

[@mcockerham2003]

It took three videos to find out how to take the head off. You did it in 34 seconds. Thank you.

[@binhminh417]

The answer which I've been searching for. I truly appreciate your invaluable guidance on this subject.

[@victorquesada7530]

I appreciate the honesty. Doing things for the camera is always harder.

[@WonderMonkey2]

Thanks for the video! You just saved me from putting it in a vice and getting a pipe wrench out, therefore ruining it and sending me back to the store.

[@sertsj1]

I have a Westward 8 piece kit, but lost the locking flathead. How would I go about getting a new one?
Thanks

[@ERRORhxc13]

I doubt I'd ever have figured simply pulling it down would work. I feel like a huge dork. Thanks!

[@Simplegroundlife]

I've been in that place more times than I can count. No judgement here.

[@jewelllane9117]

Thank you!

[@Simplegroundlife]

I'm glad it helped.

[@B.r.i.a.n.1]

The set screw is for the bit, not necessary for hole saw removal

[@unkjason]

I feel like such an idiot. I never considered pulling it down first. THANKS

[@dougharlow6037]

Well after soaking the 1” hole saw with PB-Blaster for 4 hrs. I used the impact gun and put the head or blade of the hole saw in a vice, beat the saw blade to death with a hammer. Finally came off. Thanks

[@MimiDidi121]

How about the Lenox hole saws you get at Lowe's?

[@tko6196]

Thanks great video.

[@Ghostly-00]

Thank you

[@edmondutleyjr.4504]

Thanks. I never remember this. Sometimes I figure it out, sometimes it’s to the video.

[@mariapropst7935]

Thank you so very very much!

[@Simplegroundlife]

Glad it helped!

[@kathrynnewton8721]

Does it have a dedicated drill bit because mine is too long ?

[@dougharlow6037]

I have a 1" hole saw, there is nothing holding the arbor to the blade, the screw only holds the drill in place. I’ve tried everything to get this apart, soaked in WD-40, used a vice and very large channel locks, I’ve hit the arbor and the saw itself with a hammer, etc. trying to loosen, with no luck. I noticed this post and tried the impact driver 3 times, still no luck. I’m now trying soaking in PB Blaster. I’m going to let this set for 4 hours then again try the impact again. All information and suggestions appreciated

[@mikespilde1]

Changing hole saw

[@TammyMartinBLUE]

I didn't want to break it & it is stuck, but I wasn't sure. Thanks!

[@carlosandrescifuentesandre3674]

Thank you!
I am having to soak mine in WD40 and channel locks, maybe use impact drill and see if it comes out

[@grimesjon1]

Wow! Thank you! I've never used one and about to throw a fit. Now I feel kinda dumb!

[@mikepublic111]

These don't work at all like my hole saw. The shaft on my hole saw simply screws into the saw tube. After drilling a hole for a lock, the shaft is now stuck on the tube.

[@pasqualeparente9776]

use a impact to loosen, put a hex on the chuck at the top and hold the hole saw away from the sharp teeth. Now run in reverse.

[@3lwoodBloose]

Now do a Milwaukee

[@bragifg]

Thanks.

[@MrDara1952]

Didn’t work on my ryobi as it has t the slider. Hammer didn’t work and drill either.

[@jerryschmitt5119]

would help if your light was on what your doing not in the dark . i have different model so this video dident help me thanks

[@user-zp9dr9lm5o]

Mine will not untien n screw is all the way out do I need to spray it with wd 40

[@Simplegroundlife]

They can be hard to unscrew. WD 40 or, better yet, a penetrating oil can help for sure. Good luck.

[@betsysmith2344]

What if it won’t unscrew

[@anumanthanarayanan7902]

I saw that your videos but my drill bit for broken at the bottom hand but I can't remove it. help with me

[@Kevin-xu9ym]

only useful vid I found so far

[@verity9000]

THANK YOU! The people who made the owner's manual for this thing should be in prison 😊

[@santiagomartinez9422]

Use better light, because it difficult to see .

[@Simplegroundlife]

You are right, this video is quite old and I have definitely improved my lighting and camera since filming this video.

[@MrDaiseymay]

ONE TIP---HOLD THE SCREWDRIVER BY THE HANDLE.

[@JEFFQUICKLE9]

LOL always work in the dark?

[@1bertski]

Your Your video lighting it’s too dark!

[@johnmack537]

You need better lighting. The shadowed areas are too dark.

[@itsKeaze]

Thank you

[@victororozco3074]

Joe Gatto

[@victororozco3074]

Joe gato

[@kathrynnewton8721]

Thank you!