cut a hole in glass for a cat or dog door

Поділитися
Вставка
  • Опубліковано 6 січ 2012
  • Hole in the centre of a piece of glass

КОМЕНТАРІ • 221

  • @PHDHIPHOP1
    @PHDHIPHOP1 8 років тому +35

    I am a glass cutter in New Zealand and i have never seen the inner circle before, make sense. Thanks for sharing
    .

    • @glassbeveller
      @glassbeveller  8 років тому +6

      No problem , happy to share knowledge between glaziers 👍

    • @Sana.Nadeem
      @Sana.Nadeem 4 роки тому

      Great idea
      Thanks for sharing

    • @umaiskhankhan2863
      @umaiskhankhan2863 4 роки тому

      I am 6 year Experience in glass cutting work in uae i want work

    • @bradleydavis5018
      @bradleydavis5018 3 роки тому

      Nice job.Another method is to cut 2 half moons inside the hole and then open up the criss cross cuts . It fslls out alot easier

  • @chrisridley1210
    @chrisridley1210 8 років тому +33

    only video found so far to create a round hole rather than a round piece of glass!!
    will try that. very workmanlike and careful tute. great.

    • @Guido_XL
      @Guido_XL 3 роки тому +1

      Yes, I was also looking for an instruction as how to make a decent hole in the glass for a catdoor. This video was just what I needed to get a grasp at the possible issues that an inexperienced person will face when endeavouring the same result.

  • @notgotaname
    @notgotaname 8 років тому +3

    I have attempted many hole cuts and failed before I discovered your video. Great work.
    And I see why you need to turn over and 'break the seal' directly after scoring the circle. It stops any cris cross scores following through past the circle score line. Circle cuts are incredibly hard to master and you have made it look so easy.

    • @glassbeveller
      @glassbeveller  8 років тому +1

      Thank you.
      It was hard to get the camera angle right so it showed a good reflection of the cut opening so people could follow it better 👊🏻 have fun

  • @kamilkrajewski2906
    @kamilkrajewski2906 2 роки тому +1

    Great instructional video, mate! Thanks to you, I was able to cut holes into two sheets of glass for a double glassed window to install a cat door! Greetings from Germany!

    • @glassbeveller
      @glassbeveller  2 роки тому +3

      How awesome, really glad it helped you out. I used to like being on the tools & working with glass , mirrors & bevelling glass 👍👍

    • @Oakleaf700
      @Oakleaf700 2 дні тому

      @@glassbeveller You make it look so easy- but there is YEARS of experience behind this. This is obviously a practiced hand. 🖐

    • @Oakleaf700
      @Oakleaf700 2 дні тому

      @@glassbeveller THIS is why my local glass suppliers had a series of glass circles {Rings} joined together! Clearly from cutting vent holes! I never knew how it was done. ..it was much thinner glass than this though.

  • @CatNolara
    @CatNolara 6 років тому +2

    I have just tried to cut glas for the first time and understand now, that it is more complicated than you think. It's really fascinating how glass reacts to disturbances in the structure.

  • @thomasgraham5327
    @thomasgraham5327 8 років тому +3

    yes some neat tricks. I am Glazier myself it's nice to see some new tricks I will give that one a shot. there is a lot of people posting videos on how to cut glass and they say they have lots of videos on how to glass that are done by people that don't know what they are doing but this is very clever

  • @kungfusing1
    @kungfusing1 5 років тому +20

    A fishing Rod, a Vt commodore and an Aussie flag, I think this guy is Australian.

  • @SC-rb2jr
    @SC-rb2jr 9 років тому +3

    Great video, very clear. I like the 2nd ring technique.

  • @rushellcarlson6561
    @rushellcarlson6561 5 років тому +1

    Thank You! I've been looking for round cuts for a little DIY project. This was super helpful :)

  • @homopunk84
    @homopunk84 9 років тому +16

    I like how you gave two metric measurements... 25mm or 2.5cm. Take that America! And using an otto bin as a tool brought an aussie tear of pride to my eye.

    • @dvnobles
      @dvnobles 7 років тому +2

      There was a big push in the 70's to move towards the metric system in the US, but it lost momentum...now we are left with a idiotic mixture of imperial and metric measurements (we buy 2 liter bottles of coke, but pump a gallon of petrol). Cars that I have owned that I've worked on, I had to continually switch between imperial and metric wrenches - it's really stupid. We and the other 2 imperial measurement countries need to switch...it's quite costly, but will save an untold amount of money in the long run. Thanks for this video, I like your 2 cut method - makes sense.

    • @SLOBeachboy
      @SLOBeachboy 6 років тому

      This is an excellent tutorial and its it’s really going to be a big help to me as I will be installing one of those round Plexiglas doggy doors in a sliding glass door at my mother’s house and I only have one shot at it. The problem is that after 1977 here in the USA all glass patio doors were required to use tempered glass, which of course cannot be cut. My moms door is from the early 70’s and therefore is not tempered, but if I crack it and it has to be replaced the installer would be required by law to use tempered glass, which would mean I could then no longer use this type of doggy door. This is probably why they don’t sell these doors here in the USA (I ordered mine from Australia).
      By the way, is anyone else here scratching their heads after reading homopunk84’s comments? I mean, I can’t figure out if he is just being sarcastic or if he actually thinks that knowing that 2.5cm is the same as 25mm is somehow some sort of “burn” on the USA. Lets face it, pretty much everyone on the planet with an IQ above 60 knows that the metric system is based on tens and that therefore 2.5cm is 25mm are the same thing (I learned the metric system here when I was 12 years old). Speaking of which, I would actually estimate the difference in radius between the two circles to be closer to 4cm.
      Anyway, Australia certainly has plenty of things to be proud of - AC/DC and Midnight Oil, just to name a few - but knowing that its best to break glass over a bin, or being able to use 25mm and 2.5cm interchangeably is not exactly anything to brag about.

    • @adamsaquatics3332
      @adamsaquatics3332 6 років тому +1

      I can convert quite easily since I know both. But for others, there is always Google

  • @missStaci79
    @missStaci79 11 років тому

    great video thank you. We have only one glazier in town that will do it and it seems to be a mission for them and cant do it for weeks, Lame. Glad I watched this now I know to do two circles which is a great idea. Thank you again

  • @BirdOfParadise777
    @BirdOfParadise777 12 років тому +1

    OK! Genius!!! :) I have been looking all over UA-cam for this answer! Thank you:)
    Make a million videos! You did such an excellent job on this one, I can hardly wait to watch the rest of them. I love your accent that you know you don't have;) LOL!
    BOP

  • @mikedalakis5292
    @mikedalakis5292 4 роки тому

    Brilliant work, nicely explained. Thanks much.

  • @xdogisapedo2823
    @xdogisapedo2823 9 років тому +4

    Great video only constructive critism is I wouldn't say push hard . Unless a person knows what pressures you can and can't use on glass can make the glass crack if you push hard. My advice is whay your doing is making the glass running. Basically put your thumbs literally on the glass cut and slight press down and applying pressure slowly and then the cut will crack and then you can simply start make the cut run. As you press down slightly the cut starts to run in front of you and you can follow it around to it meets the start point. You don't have to push hard jist slight push and apply pressure and you will safely keep the cut from breaking. Don't press hard as to much pressure you can break it

  • @ErinHansen69
    @ErinHansen69 10 років тому

    Great vid! Thanks so much.

  • @deendisco3083
    @deendisco3083 6 років тому

    Best tutorial, thanks a lot!

  • @albinullanger7862
    @albinullanger7862 6 років тому

    Great! Good technique, i'll make use of it. Thanks

  • @liquidstateglass6020
    @liquidstateglass6020 8 років тому +2

    thanks for sharing mate, works even with after a bevy ;)

  • @austingode
    @austingode 7 років тому

    That was brilliant.... I loved it

  • @Sparkey
    @Sparkey 10 років тому +1

    I've always wondered how this was done. Good vid.

  • @skylerjr2648
    @skylerjr2648 8 років тому +2

    Catwoman made this look super easy. Then again that's Hollywood for you.... Nice video and interesting technique.

  • @dbaider9467
    @dbaider9467 4 роки тому +1

    Sweet. Thanks.

  • @bakybi
    @bakybi 9 років тому

    Great work you did. In my application I need the ring between the two circles. Could you kindly tell me how to save the ring? and can I do the same in thicker glass sheet, say 1/4" to 1/2"?

  • @nmgal007
    @nmgal007 11 років тому

    Thank you for sharing!

  • @glassbeveller
    @glassbeveller  8 років тому +6

    After working with glass since 1980 & still in the industry it becomes 2nd nature & this stuff isn't scary at all. Gloves get in the way on small jobs like this- glasses should always be used but.. Just respect the product & never get grumpy with it or you will lose.
    ....cheers 🍻🍻 oh and never drink & glaze / cut either ha ha

  • @seanryan1592
    @seanryan1592 5 років тому

    Ive been in the glass trade 17 years never has it occurred to me to do the double circle. I do this probably once a month and they always shell. Cant wait to get to work too try this tmoz. 🤯

  • @Prefex21
    @Prefex21 11 років тому

    Great video man! thanks!

  • @spbkumar4154
    @spbkumar4154 3 роки тому

    Nice Cutting good job

  • @wadyalnil
    @wadyalnil 7 років тому

    Dankeschön, dein Video hat mir sehr geholfen 👍🏻

  • @halimanortheast4158
    @halimanortheast4158 4 роки тому +1

    Brilliant, thanks

  • @MN-wx2rs
    @MN-wx2rs 2 місяці тому

    Hi mate, Thank you for great and clear instructions. Can I use this technique for my sliding door glass which complies with Australian Standard AS 1288:2021? Thanks

    • @glassbeveller
      @glassbeveller  2 місяці тому

      AS1288 is toughened glass so existing glass can’t be cut . New toughened glass with a hole 👍 if it’s safety laminated glass it can be done by an old skilled glazier but that level of skill nowadays is rare. So just swap out using new glass thanks 👍

  • @woof3065
    @woof3065 4 роки тому

    thanx for sharing, could I do this from only the inside? I have to make a hole for my airco on the attic, and I don't have a tall ladder to reach the window from the outside.

  • @dhorton51
    @dhorton51 4 роки тому

    Can you buy the circle contraption or did you make it your self? Would really like to have on! Veey good instructions! Thanks the circle cutter? Or did for sharing!

  • @BramStolk
    @BramStolk 6 років тому

    I have a glass balcony roof, in which I want to make a man hole so I can clean it.
    I don’t have access to topside of glass, only the bottom.
    Can I still make a circular hole in it? If not, could a glazier do it?

  • @michelespinasse1763
    @michelespinasse1763 5 років тому

    Nice work,thanks. Don't forget to grind the circumference and to eliminate all the little glass fragments that could hurt your animals.

  • @birhon
    @birhon 4 роки тому +1

    Thanks for making this awesome tutorial!
    Why can't you just use the suction to pull the inner circle out rather than slicing and knocking?

  • @cougar0611
    @cougar0611 10 років тому

    Hi mate, great video. I need to put a dog door in. Never cut glass before but pretty handy in general. In your opinion should i try to do myself to save $150 or just get glazier to do it? I'm guessing pretty good chance of breaking the window given it will be first time cutting glass hey?

  • @petergwatts9037
    @petergwatts9037 4 роки тому

    Superb skills perfectly and pleasingly presented. Peter G Watts

  • @haywardglazing3522
    @haywardglazing3522 5 років тому

    good video fella......but your average DIYer wont have the circle cutter ,but good tutorial ,all the way from england

    • @glassbeveller
      @glassbeveller  5 років тому +1

      👍 thanks but it also shows people that it’s not like the movies & you just remove I circle in one piece to break in 😆🍻

    • @Oakleaf700
      @Oakleaf700 2 дні тому

      @@glassbeveller Haha yes! I bought a circle cutter identical to this for stained glass, and thought ''Now I can get myself some diamonds from a jewellers' shop' {Only joking!} but it's absolutely not like the movies.
      Curves are really hard, But this is probably one of the hardest cuts to do. {Never done one like this- I'd pay a professional just to save on glass!

  • @startreking
    @startreking 11 років тому

    I have a 5 cm diameter hole any way to make the protective circle inside that?

  • @moonolyth
    @moonolyth 4 роки тому

    Double cut Circle Excellent Description, is the a certain distance you need between the two circle cuts ?

  • @MrDas187
    @MrDas187 8 років тому

    Nice job mate ,Cheers

  • @mikesmounouchos5325
    @mikesmounouchos5325 11 років тому

    it goes the same technic for a square in the middle of the glass?

  • @tonibaloni12
    @tonibaloni12 4 роки тому

    how would you do it if it's a windows with 2 glasses , 1 on each side?

  • @DoctorRetina
    @DoctorRetina 11 років тому

    Can you do a video on how to cut out a rectangle in the middle?
    Really loved your video!!

  • @jakerm85
    @jakerm85 12 років тому

    Nice work man. I have a 6.38 lam bi-fold door I need to put a dog door in.
    What sort of technique do you use for cutting it?

  • @maximusjavelin6129
    @maximusjavelin6129 9 років тому

    Genius - many thanks.

  • @LIHUI-MOTORS
    @LIHUI-MOTORS 6 років тому

    Ths for sharing. I will try to do same thing. I hope i can success.

  • @ZiiiiingBANG
    @ZiiiiingBANG 9 років тому

    can you use turps or wd40 instead of kerosene?

  • @DrHatbox
    @DrHatbox 7 років тому +3

    A question: Can you use the same technique to cut a square/rectangle?

    • @benfidar
      @benfidar 3 роки тому

      Or a pentagon?

  • @ravanabrahmarakshas4263
    @ravanabrahmarakshas4263 6 років тому

    hello. i need to make a whole like that on a glass window which is already in the frame vertically commected t9 the wall. any additinal tips? thanks

    • @glassbeveller
      @glassbeveller  6 років тому

      Ravana Brahma Rakshas it can be done but the glass isn't as flexible in a frame, only a job for a really good glazier & if the glass is only 3mm thick in an older home ... Don't bother . I would explain but it's beyond DIY 🌹

  • @haywardglazing3522
    @haywardglazing3522 8 років тому

    we do this slightly different in the uk ,and i must say i will give this a go and see ! LOOKS A BETTER WAY ...

    • @glassbeveller
      @glassbeveller  8 років тому +1

      How did you go. This was the way my English father taught me. He was From Cheltenham ,

  • @helengloggner5852
    @helengloggner5852 4 роки тому

    A piece of Cake LOL .. good job

  • @Bullochman
    @Bullochman 6 років тому

    Nice job mate!!!!!

  • @glassbeveller
    @glassbeveller  11 років тому

    straight cutting ? to a rectangle size or a shape or hole ? . old glass is, or can be harder to work with but not unless its like 40 years old or has a colour or pattern through it. clear glass under 40 years old should cut ok. use kero on the glass then cut through the kero.

  • @amierulbahrain6265
    @amierulbahrain6265 4 роки тому

    Tq so much sir for the knowledge.

    • @glassbeveller
      @glassbeveller  4 роки тому +1

      No problem& thank you for the reply 👍

  • @SolarMillUSA
    @SolarMillUSA 11 років тому

    fraking spectacular. A+

  • @rip.tear.
    @rip.tear. 4 роки тому

    Is there anyway of finishing the circle edge so it isn't sharp, I was thinking sandpaper but it'd be very easy to scratch the rest of the glass?

    • @1953SM
      @1953SM 4 роки тому

      Watch how they do the edges in this video all the way to the end polishing process...ua-cam.com/video/KadDX4E7ND8/v-deo.html

  • @jackrodgersjr
    @jackrodgersjr 6 років тому

    Nice. But in the movies the adored bad guys hang upside down on the 44th floor and make one circle cut and then pop it out with a suction cup thingy. As a newly hired apartment manager the owner was showing me how each it is to replace a broken window pane. While doing so he cut himself. For the next 18 months I took out windows with broken glass and carried them to the window glass replacer and then back. I also caused a 4 foot black spark up a wall when I tried to separate two sparking wires with a screwdriver. So I do respect your skills.

  • @xdogisapedo2823
    @xdogisapedo2823 9 років тому

    Also the way your doing is the harder way . You don't have to do an inner circle as your more likely to break it that way and it takes far longer. Just cut little squares in the circle and tap it out and make your way to one edge of the cicle once you get there the whole thing drops out. Can be done in 30 to 60 seconds

  • @miriamquagliato1149
    @miriamquagliato1149 6 місяців тому

    Do they make round pet doors that will fit into a glass window?

  • @xzigalianisiochfhradha3204
    @xzigalianisiochfhradha3204 8 років тому +2

    Hiya, would you use the same technique to put holes in glass that has already been installed?

    • @glassbeveller
      @glassbeveller  8 років тому +5

      Almost ,...use 50 mm between the 2 circular cuts not 25mm & don't push very hard on the glass, push lighter & tap the cut open using a blunt heavy object, like the edge of a tape measure or a ball hammer. but the glass is not as flexible ,so plenty of kero and the first outside cut must be opened from the inside then go outside & open the cut again ... Then proceed. Good luck .

    • @bradwatts8222
      @bradwatts8222 7 років тому +4

      If your putting a hole in already installed glass and its on the sunny side of the building spray the desired cutting area down with your cleaner bottle to equalise the temperature of the glass first and you will have a happy day , one hotter part and it's game over , works a treat cutting flat on the back of a ute tray on a 35° day as well , set your straight edge or circle cutter , spray , wait like a minute or so till the temperature equalises and cut away , if it's your last piece of glass on the truck use the double circle method and the pentagon line approach , it will save a kick in the arse when you go back to the factory to get another piece if your in the trade , works for me and glad to pass tips on to your subs darryn , and nice job mate not a single shell

  • @redbee28
    @redbee28 11 років тому

    good job brother

  • @iral.jacobson6463
    @iral.jacobson6463 9 років тому

    Very impressive. I would have worn work gloves just in case.

  • @EclecticLensYT
    @EclecticLensYT 7 років тому

    Great Video! You wouldn't happen to know how I could cut a 3 inch hole out of the center of a table top but keep the rest of it intact? I don't wan't to break off the sides like you do in your video. Thanks!

    • @glassbeveller
      @glassbeveller  7 років тому +1

      Lucas Edwards if the glass is an outdoor table top it is probably toughened ? Look for tempered stamp in one of the corners. It is better that this be drilled out by your local glazier -AS LESS BREAKAGE RISK. if it has no stamp. (toughened glass can't be cut or drilled) A very skilled glass cutter could do this in 6mm glass or thinner with very little chipping but it is well beyond the DIY .
      Thanks for watching & feed back 👍

    • @EclecticLensYT
      @EclecticLensYT 7 років тому

      Thanks for the reply.. it is NOT tempered. I know this as I've already cut the hole. After asking I had a friend dropped off a diamond hole saw bit. I put the glass top in a kiddie pool and filled it with some water. At an angle I carefully started the cut and then with gentle but steady pressure I just let the bit do all the work. It took longer than I expected but no cracks! I then gently sanded down the edge with sandpaper. Now to make some sort of insert to help protect the edge.
      I do appreciate the reply. In my area they wanted almost $200 just to cut the hole with no warranty given if they break it. It seemed worth the risk in my case.

  • @cjmg321
    @cjmg321 10 років тому

    So, beautiful video---shows me that the movie action of zipping a circle with a cutter and popping it out with a suction cup just may be IMPOSSIBLE, eh?

  • @glassbeveller
    @glassbeveller  11 років тому

    @BirdOfParadise777 thanks very much !

  • @geraldine0318
    @geraldine0318 10 років тому

    What is the tool called that you used to make the original cuts?

    • @glassbeveller
      @glassbeveller  10 років тому

      Sorry, forgot to check this for sometime, it's a glass cutter, just use kero to assist

  • @sonjagebauer2322
    @sonjagebauer2322 3 роки тому

    Is it possible, to cut a hole in a already installed double-glass Window? (With 125mm diameter)

  • @davidb8102
    @davidb8102 8 років тому +3

    Hi Darryn, I'm planning on having a go at installing a pet door in a lower piece of glass. Only issue is that it is tinted and I don't know if it's 5mm thick. Is it possible to cut through the tinting and score the glass at the same time and if so, is it even worth it since It's probably laminated and as you say it's meant to be 5mm toughened? I was thinking the tinting may help give the glass a little extra strength?? I guess if I stuff it up I will be calling a glazier(possibly Viridian since I'm in Perth) to fit new 5mm toughened glass anyway. So do you reckon it's worth having a go myself? Cheers. Very informative video by the way!

    • @glassbeveller
      @glassbeveller  8 років тому

      No, stick on tint needs to be removed first. Use circle cutter to mark out the diameter...5mm bigger than the hole size & cut the tint by hand scalpel then remove tint first , good luck. Pull tint off fast like a bandaid and 90% of the glue comes off with the tint. But Make sure you cut through the tint all around ,

    • @davidb8102
      @davidb8102 8 років тому

      Cheers, thanks Darryn. Would you recommend removing the glass panel to cut the hole or leave the glass in place and attempt the cut. I can remove the flyscreen from the window above to help gain access to both sides at the same time...

    • @glassbeveller
      @glassbeveller  8 років тому

      +David B you'll break the glass on removal & can be don while in place ... Plenty of kero on the glass around the cut circle . Use small piece of sponge . Large circle first . Open cut both side remember the your chances are good if you get that part over

    • @davidb8102
      @davidb8102 8 років тому +1

      +darryn malpuss Success! Thank you Darryn, couldn't have done it without your video and advice! Amazing how much effort it took to break the inner circle completely out. Was stressing a crack was going to dart across the pane of glass, but it didn't. Cheers!

    • @glassbeveller
      @glassbeveller  8 років тому

      +David B great mate 👍👍
      in my video you will now notice how hard I actually had to hit the glass inner circle. I need to post something new on glass how to

  • @martynm.449
    @martynm.449 6 років тому

    Wow! Thanks for sharing your knowledge. Can you show us this in toughened glass please?

  • @glassbeveller
    @glassbeveller  11 років тому

    Mike Moynoyxo. , A square requires 4 holes drilled at each crn point with a diameter of 12mm at least. then cut vertical and horizontal to each hole, open cuts both sides. then diagonal cut to form 4 triangles. open both sides again. tap out mess. without a glass saw this is your rough way of doing a power point hole. it will chip a bit. good luck.

  • @larn555
    @larn555 8 років тому

    would this tool work on a fish tank? or would tank glass be too thick?

    • @glassbeveller
      @glassbeveller  8 років тому +1

      Same process to be used but a bit more kero and more hand pressure required. if the tank is built then manipulating the direction of opening the cut will require more skill. If it's 10 mm glass then a rubber mallet required to open the cut but press the glass then hit as shown.... HitJust behind the open cut to make it go forward 👍

  • @LovemeAquarius
    @LovemeAquarius 11 років тому

    Damn.......genius

  • @glassbeveller
    @glassbeveller  4 роки тому

    You can roll the sand paper
    Around some wooden dowel
    Rod , wet and dry is best
    Then would be an issue

  • @didanhtennis
    @didanhtennis 7 років тому

    That's great. Where can I can get that tool or cutter. I would like to cut the square hole for a small dog to go through the glass door that I currently have now. Is it doable or I have to hire someone to do it? I like to do it myself if possible to save money. Thanks for the video.

    • @GlassGenius
      @GlassGenius 7 років тому +1

      You must have a dog door for a wooden door. You need the circle adapter for your brand of dog door then it will fit on a round hole in glass.

  • @CauseImYourFat
    @CauseImYourFat 5 років тому

    I did the same but my whole glass s breaking down lmao XD how that guy can just knockout the glass just with fingers XD

  • @shopski
    @shopski 4 роки тому +1

    Hi, what do you smear on the glass before you do the round cut ?
    Thanks

    • @glassbeveller
      @glassbeveller  4 роки тому

      Atanas Shopski Just kerosene. A bit messy but this is key to the success as is a nice glass cut . Not a cut that is hit & miss. 👍👍

    • @rustygear9370
      @rustygear9370 4 роки тому

      @@glassbeveller Can we use gasoil instead ?

    • @glassbeveller
      @glassbeveller  4 роки тому +1

      Atanas Shopski gas oil ?
      Sewing machine oil is to thick & that is thin oil. I mix a bit of kero with sewing machine oil & put that in the glass cutter or on the wheel. Run the cutter down the glass with NO pressure to make a thin line of lubricant then make the cut though the wet line. 👊🏻👊🏻

  • @glassbeveller
    @glassbeveller  11 років тому +1

    thank you very much. L Bandara, and SolarMillusa. I'll tell my wife that you know me better than she does. lol

  • @lenny108
    @lenny108 6 років тому

    nice, but how you do it in glass door, big piece of glass?

    • @glassbeveller
      @glassbeveller  6 років тому

      lenny108 your glass door may have safety glass in it so in most cases you can't. But if it's not safety glass then much the same process - just vertical & requires a little more skill as the glass is harder to flex & manipulate where the opening of the cut direction should follow .
      Break out the glass mess into a vertical box the other side of the door to retain
      Most of the fragments & waste. 👍🏼

  • @btk1w1
    @btk1w1 8 років тому

    Hi Darryn.
    I want to put in a pet door that needs a 267mm circle cut out of a pane that's 550x620 (inside an aluminum frame). It's a fixed bottom window that meets the floor. The house is 30-35 years old.
    I have called a couple of glaziers and they have told me the glass thickness is only 3.75mm and I need toughened 5mm glass. They say $300+ for the job.
    What are your thoughts on this? I would love to have the pet door installed there but at this cost I would sooner hack a hole in my security screen and do it there instead.
    Mate is this worth doing or should I save myself the hassle and just put it on the security screen instead?
    I would love your feedback. Cheers.

    • @glassbeveller
      @glassbeveller  8 років тому +2

      They are correct. By law it has to be TGH 5mm as there is no strength in 3 or 4mm glass not toughened,

    • @glassbeveller
      @glassbeveller  8 років тому +2

      If your in Perth go to Viridian glass . But $300 isn't bad for a call out and replacement due to skill level involved

    • @btk1w1
      @btk1w1 8 років тому

      +darryn malpuss cheers mate. Awesome feedback. Perth is on the opposite coastline from me, I'm in Brisbane :-) I'm going to put it in the screen door because it is the cheapest option. Didn't realise there were so many things to consider with a pet door window install but your explanation has made perfect sense of it all. It really does pay to check with the experts.

  • @ben6089
    @ben6089 4 роки тому

    Alright, now I know that's way beyond my skill level and I can call a pro to do it.

    • @glassbeveller
      @glassbeveller  4 роки тому

      Ben McLeod some so called tradies have a problem & watched this to get a better idea cheers 👍

    • @ben6089
      @ben6089 4 роки тому

      @@glassbeveller Thanks man, I'm an electrician and was hoping it wouldn't be much harder than making a round hole in a piece of plaster board haha.

    • @glassbeveller
      @glassbeveller  4 роки тому +1

      Ben McLeod
      I thought wiring up colour coded wires would be easy but when smoke appears I was reminded that I’m a glazier. 🤪 ha

    • @Jaydenmbuthia
      @Jaydenmbuthia 4 роки тому

      @@glassbeveller how about laminated glass

    • @glassbeveller
      @glassbeveller  4 роки тому +1

      fridahmuthoni
      It can be done but way beyond DIY, I have done it & some really good glaziers can’t do it. So they opt for cutting it in 5 or 6mm glass & get it toughened. But the toughened product is stronger & I would recommend anyhow.
      Lamy used if you needed it done right now & you were way out of the city.
      Thanks 🇦🇺

  • @glassbeveller
    @glassbeveller  12 років тому

    it can be done but it will break at a later stage. not easy to do ,to hard to achieve for a non glazier. recommend Toughened 5mm glass an swap over the full sheet. laminated glass is very fragile with a hole missing , it is only 2 pieces of 3mm glass. ...

  • @jitendrasikar2388
    @jitendrasikar2388 11 років тому

    good

  • @TheCerberusInferno
    @TheCerberusInferno 8 років тому

    Excellent explanation , thanks a lot my friend ! by the way are you Australian ?

    • @glassbeveller
      @glassbeveller  8 років тому

      Yes, but a touch of pommy accent comes from living & working with the English family for to many
      years

    • @TheCerberusInferno
      @TheCerberusInferno 8 років тому

      +darryn malpuss Ok , Australia is a great country , have a nice day my friend

  • @PRBB25
    @PRBB25 3 роки тому +2

    This is not how I saw it done in the movies 😂

  • @user-bq6ur2wz7r
    @user-bq6ur2wz7r 5 місяців тому

    Балеге калдынау бала пакыр осындай заказдан жане бесеуин алсан куни менен журесен

  • @ameerhamza6465
    @ameerhamza6465 5 років тому

    Very simple bro my work in pakistan

  • @dmak2
    @dmak2 8 років тому

    Slight problem, I need the round bit! I'll figure it out :)

    • @glassbeveller
      @glassbeveller  8 років тому +1

      Glass & glazing hardware shop . You won't cut it free hand. Not a chance.

  • @zetamob
    @zetamob 6 років тому +1

    thank you !!

  • @jerrycastaldo8688
    @jerrycastaldo8688 2 роки тому +1

    Are you going to have it tempered before you put it in your doggie door? You can’t put annealed glass in a door

    • @glassbeveller
      @glassbeveller  2 роки тому

      No this went in the bin. Just done this video for UA-cam & to show the manual way of cutting a circle & for DIY information but yes/ toughen the glass afterwards is always recommended for any DIY..

  • @cory0702
    @cory0702 5 років тому

    Can you do this without removing the glass from the frame.
    Thanks Sid

    • @glassbeveller
      @glassbeveller  5 років тому

      Sid May yes if the glass is not toughened or laminated. If it’s only 3mm thick then it’s to thin & you need new glass. Just not as flexible so more risk of breakage. Use plenty of lubrication on the cutter

    • @cory0702
      @cory0702 5 років тому

      Thanks, I'm worried about breaking it, the glass is close to 100 years old

    • @glassbeveller
      @glassbeveller  5 років тому +1

      Sid May it will be very thin then. If you haven’t done it before then you have very little chance of success
      👍

  • @faridahmad360
    @faridahmad360 7 років тому

    oil use kerosin ?

    • @glassbeveller
      @glassbeveller  7 років тому

      Use Kerosene to cut through, or add a bit of kero to thin down the oil.

    • @faridahmad360
      @faridahmad360 7 років тому

      ok.. thanks for tutorial.. its useful

  • @reneeduardoperezalvarez929
    @reneeduardoperezalvarez929 5 років тому

    Rear sliding glass door are made with tempered glass too tough I do not know if can be done

    • @glassbeveller
      @glassbeveller  5 років тому

      Toughened glass can’t be cut . New glass required with a hole cut into the panel then toughened & replace the old one
      New piece must be Toughened, laminated S not a good choice 👍

  • @susheelkumbhkar5722
    @susheelkumbhkar5722 6 років тому

    how ..cut it on 12 mm glass

  • @gamesdisk
    @gamesdisk 7 років тому

    I am going to try this on a double glazed window. I'm really worried about messing it up. The window is already fitted into the bottom panel of a door.
    any extra tips?

    • @glassbeveller
      @glassbeveller  7 років тому +1

      gamesdisk you need access to both sides of the glass & in a DGU you don't have access. Can't be done. You Need to go to your local glazier , he will get a new DGU made up in toughened glass
      cut to this size with 2 holes in. also being in a bathroom its probably A safety glass, don't try it. It won't work. 👍

  • @misterlouisjean
    @misterlouisjean 8 місяців тому

    What’s the name of that cuter plz?

  • @MARDIUNO7
    @MARDIUNO7 11 років тому

    THERE GOES SAFETY FIRST !...

  • @AkhileshGupta-rc2jn
    @AkhileshGupta-rc2jn 4 роки тому +1

    Niceee..

  • @heavenstomurgatroyd7033
    @heavenstomurgatroyd7033 4 роки тому

    And the best part is it shreds the fur off the cat every time he uses it......