The headers are fine at 2" understand only one pipe is pushing at a time per header in a timed manner the venturi shaped end flange will increase velocity and that's a good thing to help scavenge any residual burnt gasses ...I'm positive the header company tested many prototypes before they released the final product ... no worries ... Bolt them on 😊
The dynatech headers don’t come ceramic coated as a standard. It’s an option that cost a few hundred more dollars. Did the owner of project Gabby pay extra for the ceramic coating or buy the standard dynatech which is uncoated 304SS?
Thank u we have alot of content on lightning and other vehicles so u can check them out 👍 this November and December will be crazy loaded with lightning content
I have a 2002 Lightning and looking to do exhaust, but doesn't seem that there is a kit out there for them. Wanting to go long tube. Do you have part numbers for the exhaust system you used for project Gabby. Headers mufflers X pipe etc. I know there will be fabrication involved, but not much info on it out there. Thank you, Sir
On the headers depending on what u want and budget. I would buy some pace headers they run about 280. And I would make a custom 3" exhaust with X pipe and I can buy the exhaust u want. I've looked for some cat back kits and most are 2" pipes they have restriction. On power
@@boosteddave4603 thank you! I got the driver's side in from the side very easily and was even able to use studs (I don't have immediateaccess to bolts). I'm doing the passenger side tomorrow. Did you have to remove anything anything other than the fender liner and wheel for extra room?
@@boosteddave4603 thank you! I know its a bit different but I'm installing shorty headers on a 4.6. Personally I'd think I'd have more room than your situation since our heads are the same but your deck height makes the fitment tighter. I'll try going through the bottom next
Thanks for the videos Dave👍, quick question .... My lightning makes a rattling noise on cold starts., then it gradually goes away ... Any idea what this could be?
I am here to help out. And yes the just because your oil drained all the way down to the oil pan.. and on a cold start it kinda start not dry but just very little oil... then wen the oil pressure picks up and all the vaines of the oil are fully pressure up the sounds gose away
@AlbertoSanchez-rv6yg I am guessing it should. Haven't really work on a 06 model. I am hoping the intake bolt pattern are the same as the 99 and 04 lightning/Harley
Not at all. Just make sure not to brake any manifold bolts.. and if u want u can remove your starter to have more space.. the easy side is the driver side
@@boosteddave4603 So best thing is to spray the bolts first? I took my mufflers off because I had a bad rattle now I don’t know if the cats are plugged up but it’s still hesitating to get up to speed so I’m thinking of just pulling that off and putting headers on there
Dont cut the headers! I can guarantee you will lose power. The pinch on the exhaust that goes from 3.5 to 2.5 is there to create a increase scavenging effect. Do some research on scavenging effect and the results will shock you. This is not a restriction. I can guarantee you of this information.
Ocupo tu ayuda haha Que timing chain set recomiendas? He buscado pero me salen mucho y no se cual pedir .. que no sea OEM 2001 Lightning stock Thank you
@drick2659 it all depends on miles years and specially clean title no rust from 18 to 50k plus in really good condition. Right now I have one it's a 2004 model with 8333 miles and it's worth 50k
@@boosteddave4603 I have an 03 . 118,000 Mi on it I've replaced everything and it runs like crap has a massive shutter when you slam it to the floor and it won't fall out of a tree. I'm ready to sell
@@boosteddave4603 Plugs tr6. Gaped at .35. New Motorcraft coils' Maf. PVC hose to turkey pan. Truck doesn't throw any codes. Idols just fine. Has smaller upper and bolor exhaust. That was on it when I bought it. It acts as if it has a vacuum like but I can't find it.
U do need to get a tune and it depends if i buy the o2 extension the service won't come on. But on most cases when u add headers they eliminate the rear o2 sensor and tbey just leve the front ones and u won't have any codes
@@boosteddave4603 cool i have an 06 gt. Need to look over motor first needs work has cam port polish heads bought it like that but need to get it running right. Sound like bearings knocking
@@boosteddave4603 i would like to know what the price would be, my truck has 190.000 miles and i live in Oregon I do have family in S.A. and I visit often. I really enjoy watching your videos.
Can't wait to see project Gabby finished 😊❤️. I really like how you explain what's going on.
Thank u appreciated.. I try my best lol sometimes I forget stuff. Haha 😄
@@boosteddave4603 you're good lol. Thank you
Awesome videos
@@yayacanales2297 thanks 😁👍
Nice build, can’t wait to see the power it makes, I have an 03 Harley Super Charged
Thanks 👍 the Harleys are really nice my brother in law had one but he sold it years back
The headers are fine at 2" understand only one pipe is pushing at a time per header in a timed manner the venturi shaped end flange will increase velocity and that's a good thing to help scavenge any residual burnt gasses ...I'm positive the header company tested many prototypes before they released the final product ... no worries ... Bolt them on 😊
Sup Dave. Just came across your channel .. so far looks like your doing a hell of a job..👍👍
Thanks appreciated the support and the comments 👍
The dynatech headers don’t come ceramic coated as a standard. It’s an option that cost a few hundred more dollars. Did the owner of project Gabby pay extra for the ceramic coating or buy the standard dynatech which is uncoated 304SS?
I think he did because like u sed it's and extra to get the coding on them
Great video Dave! As always!! Great explanation on everything! Keep up the great work!!! You’re a working machine!
Thank u appreciated all the support and the comments... 👍💪
Awesome...you guy's( David & Mando) always knock it out of the ball park..puro home run..👍👍👍
Thank u Mr manny the blower will be dropped of this Saturday 😁💯
Very good video keep them coming from Illinois
Thank u we have alot of content on lightning and other vehicles so u can check them out 👍 this November and December will be crazy loaded with lightning content
I have a 2002 Lightning and looking to do exhaust, but doesn't seem that there is a kit out there for them. Wanting to go long tube. Do you have part numbers for the exhaust system you used for project Gabby. Headers mufflers X pipe etc. I know there will be fabrication involved, but not much info on it out there. Thank you, Sir
On the headers depending on what u want and budget. I would buy some pace headers they run about 280. And I would make a custom 3" exhaust with X pipe and I can buy the exhaust u want. I've looked for some cat back kits and most are 2" pipes they have restriction. On power
@@boosteddave4603 I really appreciate you getting back to me. Top notch.
@@chrisredman5114 I always replied back to every comment and question haha.
Do you remember which way you fished the passenger side through? From up top, underneath, side?
From under both side u will have to twist it a little to get then in
@@boosteddave4603 thank you! I got the driver's side in from the side very easily and was even able to use studs (I don't have immediateaccess to bolts). I'm doing the passenger side tomorrow. Did you have to remove anything anything other than the fender liner and wheel for extra room?
@@BLueFeaTHeRedOliVeS no problem bro and yes sr just that bro
@@boosteddave4603 thank you! I know its a bit different but I'm installing shorty headers on a 4.6. Personally I'd think I'd have more room than your situation since our heads are the same but your deck height makes the fitment tighter. I'll try going through the bottom next
@@BLueFeaTHeRedOliVeS shorty headers are more simple to install and have more room compared to the long tube
Thanks for the videos Dave👍, quick question .... My lightning makes a rattling noise on cold starts., then it gradually goes away ... Any idea what this could be?
I am here to help out. And yes the just because your oil drained all the way down to the oil pan.. and on a cold start it kinda start not dry but just very little oil... then wen the oil pressure picks up and all the vaines of the oil are fully pressure up the sounds gose away
What kind of oil are u using and miles on the truck
You and mando Keep up the good work brotha!🤟🏻
Thanks bro we appreciate all the support form ya 💯
I have a 06 f150 with a 4.6 2v could one of these supercharger fit my 4.6 ?
@AlbertoSanchez-rv6yg I am guessing it should. Haven't really work on a 06 model. I am hoping the intake bolt pattern are the same as the 99 and 04 lightning/Harley
@ I’m starting to think a single turbo on low boost would be an easier option how to you tune ur white 4dr is it on a stock ecu ?
@AlbertoSanchez-rv6yg yes it's stock ecm and now I have that setup on my single cab 1997 I have some viedo on the channel
@@boosteddave4603 haha bro I been watching all your videos lol my favorite is you racing the 5.0 mustang with the 4dr !!
@AlbertoSanchez-rv6yg that was a great race bro.
Hey Dave how hard is it to install the Headers is there anything I need to be aware of before I try it myself
Not at all. Just make sure not to brake any manifold bolts.. and if u want u can remove your starter to have more space.. the easy side is the driver side
@@boosteddave4603 So best thing is to spray the bolts first? I took my mufflers off because I had a bad rattle now I don’t know if the cats are plugged up but it’s still hesitating to get up to speed so I’m thinking of just pulling that off and putting headers on there
@@ryangamache8049 yea u can. Makes it easier and maybe the In side of the cattletic cane lose.
Dont cut the headers!
I can guarantee you will lose power.
The pinch on the exhaust that goes from 3.5 to 2.5 is there to create a increase scavenging effect.
Do some research on scavenging effect and the results will shock you.
This is not a restriction.
I can guarantee you of this information.
Thanks for the information and we didn't cut them we left them the way they are. Came out great
Do you know where I can get those headers can’t find them
@SVTGerald lethal performance has them for 950$ dynatech i think that's was the brand
Que paso bro 😎 I’m about to do the same to the shamu 😅 any tips ? Did u removed the transmission like the mustangs or not?
No bro.. just thr starter thats it
@@boosteddave4603 ehh bad ass I’m going to order some this weekend.
@@J.PROJECTZ lmr sell them bro. Just make sure they are not om back ordered bro
@@boosteddave4603 I yeah a lot of companies are out of stock I’m probably going with bassani headers and y pipe what do you think of them ?
@@J.PROJECTZ go with long tube headers bro. And X pipe 3" all the way bro it the best way to go and make more power
What mid pipe did you use with the dynatech headers and bassani?
The same bassani mid pipes that came with the kit they have high flow cats on them bro
Oh ok bc I was looking into that set up but noticed that the bassani mid pipe and dynatech headers have different flange
Ocupo tu ayuda haha
Que timing chain set recomiendas? He buscado pero me salen mucho y no se cual pedir .. que no sea OEM
2001 Lightning stock
Thank you
What's the hp increase for adding headers
Around 15hp plus when u tune it u will get more out of them
Hey bro got any lightning parts ? Just bought a truck with missing parts
What's one of these worth running?
@drick2659 it all depends on miles years and specially clean title no rust from 18 to 50k plus in really good condition. Right now I have one it's a 2004 model with 8333 miles and it's worth 50k
@@boosteddave4603 I have an 03 . 118,000 Mi on it I've replaced everything and it runs like crap has a massive shutter when you slam it to the floor and it won't fall out of a tree. I'm ready to sell
@drick2659 what parts have u replaced maybe I can help you out getting running
@@boosteddave4603 Plugs tr6. Gaped at .35. New Motorcraft coils' Maf. PVC hose to turkey pan.
Truck doesn't throw any codes. Idols just fine. Has smaller upper and bolor exhaust. That was on it when I bought it. It acts as if it has a vacuum like but I can't find it.
@drick2659 gap the plugs to 28 and add me on Instagram so I can respond u faster and help u out
Do you need to retune after installing headers and if the Check engine light comes on
U do need to get a tune and it depends if i buy the o2 extension the service won't come on. But on most cases when u add headers they eliminate the rear o2 sensor and tbey just leve the front ones and u won't have any codes
Looking good
Thanks bro appreciated
U would happen to work on 4.6 motors
Yes sr we do..any 2v engine or 3v or 4v ford motor
@@boosteddave4603 cool i have an 06 gt. Need to look over motor first needs work has cam port polish heads bought it like that but need to get it running right. Sound like bearings knocking
@@jramos1173 we can check it out no problem bro
@@boosteddave4603 where u all. Located?
Sick video bro 👌🏻
Thanks bro
Where can I find the 4 link that you put it?
The rear drop kit
@@boosteddave4603 the traction bars?
@@ofantasticomundodetimbas lmr sell them they are stifflers traction bar systems. Price is 524 plus shipping. I recommend them the fitment is perfect
@@boosteddave4603 thanks man for the help
@@ofantasticomundodetimbas no problem bro anytime 👌
Dud i love eating and B watching videos like this keep it up bro🙂🙂👍
Thank u appreciated and will fo the best we can
are pace headers good?
Yes sr I had some for about 9yrs still good no leaks or broken welds
can u send link of them?
hellls yeah 🔥🤙🏻
U know it 💯
How much power is it pushing
You still gonna make scatpack video’s?
Yes sr I have a video coming up on an updated
@@boosteddave4603 hell yeah how did your car run with the Greene tune?
@@Scatpack-kd3wz it was running great but the transmission went out bro I will have a video this Friday on that
Where are you located
Zapata tx bro
I have 2002 f-150 Harley Davidson supercharged and I want to do they same work to my truck they you do to that How much the cost to do all that work
@@jesusruiz2980 them harleys are nice bro. And for the headers or drop kit supercharger removal and paint/ clean up and full tune up
@@boosteddave4603 i would like to know what the price would be, my truck has 190.000 miles and i live in Oregon I do have family in S.A. and I visit often. I really enjoy watching your videos.
@@jesusruiz2980 appreciated the support bro and add me on Instagram @boostedlife294 and I can respond and give u all the price bro
🤘🏼🔥🤘🏼🔥🤘🏼🔥🤘🏼🔥
👍💯
Hey brotha can you send me a picture on of how the intercooler piping went
Goes I think I’m missing a hose due to pervious owner not having a intercooler reservoir
@@EliteMexicanxX add me in Instagram ill help u out @boostedlife294
🔥🔥
💯👍
Great content🔥
Thank u appreciated 💪
👍🏼
Thank u appreciated
I can see you and camera crew reflections in the video tile u uploaded to this clip. Lmao. Thumbs down 👎🏾
Sure thanks good day to u