Thanks for creating content that I find interesting, informative, and entertaining. I have a Pavo 20 Pro Nightfire Edition on order. I couldn't pass up the 20% off coupon for Black Friday 😆. This is a great review and set-up video. Really good production value. I appreciate your efforts. Happy flying amigo. 🫡 🍻
one thing to note that "airmode is permanently on" by default in the configuration tab. so if you want to catch the drone or hit a wall it will maxout the motor rpm or go crazy thinking that it's a airgush trying to sway the drone. I usually keep my airmode on a switch-modes tab
@@gamingisnotacrime in case you have the bnf version, the PINIO LED is already hooked up to UART6. There is no need to enter CLI command to remap the resource as it came preconfigured. Just find USER1 under Modes and assign a radio channel/switch to it, and set the range accordingly.
@@flyingpudding i bought bnf, but i update the version of betaflight and forgot to the backup, what commands i need to use for using user1 in modes for turning on and off leds?
@@gamingisnotacrime no prob. U may follow the instruction on their product page: betafpv.com/products/pavo-series-cob-led-strip Make sure you adjust the procedure and reference UART6 (where the LED is connected in bnf) instead of UART1.
I put the Led strip on but its to long (the cutting line is further away from the start) can i just cut it so it fits or can i only cut it at the cutting line?
As far as I know, it would only work if you cut at the cut line instead of anywhere. Try re-routing the strip so that it wraps around the hoops properly. You may apply new double sided tape if necessary.
Very helpful video. One question, does the 03 cable go in only one way? I plugged mine in and it clicked in with the blue wire on the left but not sure if it only goes in one way. Thanks
@@keithpederson3629 It should only go one way. You may look at the socket on the O3 and check the relative position of the pins inside - they are closer to the bottom. The O3 cable plug also has slots closer to one side - check before push the plug in.
You may use the binding procedure on this page under "Serial ELRS 2.4G RX": betafpv.com/collections/brushless-flight-controller/products/f4-2-3s-20a-aio-fc-v1
Mine measured at around 560mm. Please use my affiliate link to support my channel, thanks! shorturl.at/0ujVZ BTW the LED strip is included if you get the whole quad, unless you are looking to get the frame separately.
@@RTSLV They are very different machines designed for different uses. The Neo is very versatile that you could even use it with your phone, while it is also very underpowered for aerobatic. For those who already have the G3 Goggles and RC3 remote, Neo may appeal to them as an affordable addition.
This will run circles around the neo in every aspect of performance and video quality. But it is a manual control drone it won't self hover with GPS or be able to follow. Most importantly, it is a true FPV drone. It does not come ready to fly with a remote, batteries, charger or a video system. You need to have basic FPV knowledge to get this thing bound to a remote and up in the air. You also need to get up to speed on safe charging, handling and storage of Lithium Polymer batteries.
If you have to ask, you should stay with Neo. This is a hot rod compared to the DJI consumer brand. It takes much more prep and knowledge to get this to fly.
@ yes I bought the avat 2 creator combo and just picked up the controller 3. I’ve really been wanting a micro drone for indoors but I saw on a review it didn’t work for this guy who had the controller 3 but he was in Africa so I dont even know
When the top holes are used, I can still get no prop view at zero tilt angle after Gyroflow post processing. A little bit of the ducts can be seen in goggles when flying with no tilt.
@@blalaze the Pavo20 Pro is a larger and more powerful quad than the original - it is more than capable to carry the stock antenna, which it offers better performance while sitting higher and further away from the fuselage.
That is a good idea, adding a few grams shouldn't affect flight performance when the quad grows to this size. On the other hand, ELRS antenna position may also be a limiting factor.
@@duytruong5002 technically you can. You will need to some how secure the analog vtx in the vtx cage with the included 20x20mm adapter. I am curious to know why you would want to use analog with the Pavo20 Pro?
The only thing I don't like about the Pavo, is that the battery is on the bottom, this is why I'd choose the Gofilm 20 through Caddx than the Pavo system. Plus DJI is like iPhones, and I don't like iPhones!
My guess is that it is a logical choice to belly mount the lipo while the O3 is on the top; so that CG is balance. Another advantage is prop clearence is better especially taking off on rough surfaces. It's also very easy to swap and share the O3 with my other quads. On the other hand, I have been an adroid user for over a decade so I feel you! We pilots always welcome more competition and I think Walksnail Moonlight is a good rival.
tysm - this detailed set up is so helpful!
Thank you for watching, happy flying!
Well, i love the way you explain things! Step by step assembling was super clear! Thanks
@@SiOgie Thank you very much, I am glad you enjoyed my content. Stay tuned!
Thanks for creating content that I find interesting, informative, and entertaining. I have a Pavo 20 Pro Nightfire Edition on order. I couldn't pass up the 20% off coupon for Black Friday 😆. This is a great review and set-up video. Really good production value. I appreciate your efforts. Happy flying amigo. 🫡 🍻
I am glad that you found my video useful. Congrats and happy flying!
I just got this model and you're video was amazing, thank you!
Congrats and thanks for watching!
one thing to note that "airmode is permanently on" by default in the configuration tab. so if you want to catch the drone or hit a wall it will maxout the motor rpm or go crazy thinking that it's a airgush trying to sway the drone. I usually keep my airmode on a switch-modes tab
@@Copterlord good tips, thank you very much on behalf of everyone!
I'm waiting on mine in the mail however this will be my go to setup video. Great Content.
@@yungerallenelectricalcontr6415 Congrats and thank you for watching!
Great video, love it. 😍exactly what I needed
@@nebz_fpv Thanks for watching! Don't forget to check out my Toothpico video too! ua-cam.com/video/JrTMNojF4II/v-deo.htmlsi=xt8VfMPSbEVXypxq
Such an inspiring video! Well done! :)
@@fe-xe2dj Thanks for watching and your comment!
I like your explanation. Subbed
@@TNPilipinas Thanks for your comment and sub!
Wow. Great information for this drone. 👍😁
@@garionhk Thank you very much for watching and your comment!
what commands i need to do in cli for my pavo 20 for turning on and off led?
@@gamingisnotacrime in case you have the bnf version, the PINIO LED is already hooked up to UART6. There is no need to enter CLI command to remap the resource as it came preconfigured. Just find USER1 under Modes and assign a radio channel/switch to it, and set the range accordingly.
@@flyingpudding i bought bnf, but i update the version of betaflight and forgot to the backup, what commands i need to use for using user1 in modes for turning on and off leds?
@@gamingisnotacrime no prob. U may follow the instruction on their product page: betafpv.com/products/pavo-series-cob-led-strip
Make sure you adjust the procedure and reference UART6 (where the LED is connected in bnf) instead of UART1.
Great job🎉,very inspiring.
@@macaronpompom88 Thanks!
I put the Led strip on but its to long (the cutting line is further away from the start) can i just cut it so it fits or can i only cut it at the cutting line?
As far as I know, it would only work if you cut at the cut line instead of anywhere. Try re-routing the strip so that it wraps around the hoops properly. You may apply new double sided tape if necessary.
@@flyingpuddingill try that thanks
Very helpful video. One question, does the 03 cable go in only one way? I plugged mine in and it clicked in with the blue wire on the left but not sure if it only goes in one way. Thanks
@@keithpederson3629 It should only go one way. You may look at the socket on the O3 and check the relative position of the pins inside - they are closer to the bottom. The O3 cable plug also has slots closer to one side - check before push the plug in.
i can use the radiomaster boxer with this drone and how to?
You may use the binding procedure on this page under "Serial ELRS 2.4G RX": betafpv.com/collections/brushless-flight-controller/products/f4-2-3s-20a-aio-fc-v1
Good video.
@@JakeBullit123 Thank you for watching and your comment!
Can you tell me the command in the CLI so that user1 appears, thanks
You may want to follow the instruction on the product page. betafpv.com/products/pavo-series-cob-led-strip
@ thank bro
@ In the end, with what you have happened to me, user1 came out but I have assigned it to the controles and it does nothing with the leds
@@TheDavid76 which UART is it connected to?
@@flyingpudding Usb vcp configuration on, uart 3 rx serie on, uart4 configuration/MSP on Periferic VTX(MSP Displayport)
What size LED Strip should be ordered for the Pavo20 Pro? The BetaFPV site has 560mm and 750mm varients.
Mine measured at around 560mm. Please use my affiliate link to support my channel, thanks! shorturl.at/0ujVZ
BTW the LED strip is included if you get the whole quad, unless you are looking to get the frame separately.
@@flyingpudding Thanks :)
Which will better this or DJI neno and which will be more cheaper build or buy
@@RTSLV They are very different machines designed for different uses. The Neo is very versatile that you could even use it with your phone, while it is also very underpowered for aerobatic. For those who already have the G3 Goggles and RC3 remote, Neo may appeal to them as an affordable addition.
This will run circles around the neo in every aspect of performance and video quality. But it is a manual control drone it won't self hover with GPS or be able to follow.
Most importantly, it is a true FPV drone. It does not come ready to fly with a remote, batteries, charger or a video system. You need to have basic FPV knowledge to get this thing bound to a remote and up in the air. You also need to get up to speed on safe charging, handling and storage of Lithium Polymer batteries.
@@brandon9689 well said! Thus they are very different machines for different uses.
If you have to ask, you should stay with Neo. This is a hot rod compared to the DJI consumer brand. It takes much more prep and knowledge to get this to fly.
Very nice🎉
Thanks for watching and your comment!
Will this work with the dji controller 3?? If I’m using the 03 controller
@@LayinLo Yes, assuming that you are also using Goggles 3.
@ yes I bought the avat 2 creator combo and just picked up the controller 3. I’ve really been wanting a micro drone for indoors but I saw on a review it didn’t work for this guy who had the controller 3 but he was in Africa so I dont even know
@@LayinLo Controller 3 transmits signal via the Goggles instead of to the air unit directly. Maybe he set it up incorrectly?
@ hopefully he did cause I just purchased the frame and 03 unit. I’ll make a video unboxing and trying to set up 🩵
@@LayinLo Look forward to it! Happy building.
great review, one question though are the ducts in view in low camera tilt regardless of the camera mounting hole that you use?
When the top holes are used, I can still get no prop view at zero tilt angle after Gyroflow post processing. A little bit of the ducts can be seen in goggles when flying with no tilt.
@@flyingpudding so ducts will be always in view regardless of the camera hole mount you use? I mean in view in the goggles not the final video
@@carlosfuhrer Yes, you would get tiny bit of ducts view at zero tilt while using the top holes.
Why did you decide to keep the stock antenna instead of using the tiny one that most others swap to?
@@blalaze the Pavo20 Pro is a larger and more powerful quad than the original - it is more than capable to carry the stock antenna, which it offers better performance while sitting higher and further away from the fuselage.
@@flyingpudding I am glad you used the big one. I was thinking the same.
Sorry kind of new , the part where you say "sbus fast on " does not work . am I typing it in wrong ?
I can't seem to recall that I mentioned "sbus" in this video. Would you mind telling me the timestamp and I will look for it?
@@flyingpudding sorry , wrong video I was watching so many videos at the time got me all confused :) this vid helped set my Pavo up thanks!
@@retro93277 Glad to help, happy flying!
can we still use 2s battery on pavo 20 pro?
@@donquibtc theoretically yes, but it will be underpowered. Keep the weight at minimum and it should still be ok.
Link the store pls.
@@reditoyongco7343 please see the description and thanks for watching!
i gave up on binding mine lol. it would bind but it wouldn’t allow me to arm no matter what i tried.
sorry to hear. Please connect with me on IG @flying.pudding and see if I can help.
Nice Job! I wonder how long it will be before GPS will be available from Betafpv?
That is a good idea, adding a few grams shouldn't affect flight performance when the quad grows to this size. On the other hand, ELRS antenna position may also be a limiting factor.
@@flyingpudding I'm not sure what you mean...?
@@CCC0122 whoops I got the wrong idea. I just realized that Betafpv does not have their own GPS module 😆.
Nice with O3 but can we do with analog instead?
@@duytruong5002 technically you can. You will need to some how secure the analog vtx in the vtx cage with the included 20x20mm adapter. I am curious to know why you would want to use analog with the Pavo20 Pro?
@@flyingpudding just wanna test with analog first then do the upgrade to dji combo, u know dji quite expensive lol
@@duytruong5002 ah yes, post your mileage!
Interesting ! but music too loud.
@@greelyguala5952 Thanks for watching! I will keep make adjustment in next one. 👍
are you in Burnaby? :)
@@momofpvdrone Yes. Let's connect in IG @flying.pudding
Great video, but background music is too loud.
Thanks for watching and your comment. I will make the VO stand out more next time.
The only thing I don't like about the Pavo, is that the battery is on the bottom, this is why I'd choose the Gofilm 20 through Caddx than the Pavo system. Plus DJI is like iPhones, and I don't like iPhones!
My guess is that it is a logical choice to belly mount the lipo while the O3 is on the top; so that CG is balance. Another advantage is prop clearence is better especially taking off on rough surfaces. It's also very easy to swap and share the O3 with my other quads. On the other hand, I have been an adroid user for over a decade so I feel you! We pilots always welcome more competition and I think Walksnail Moonlight is a good rival.
Oddityrc. Check them out. Whoops that fly like freestyle quads
@@LoVeAmBiEnT i do have that frame but haven't got around to build it yet. It is substantially heavier though.
Seems like an AI voice?
Definitely an ai advertisement.
@@xXxCobraCommanderxXx Yes, I have started adding VOs in my recent videos.
@@jordancalhoun5238 Everything in the video except the VO is still "organic". Thanks for watching and your comment.
Clearly, he's just a cyborg 😅
@@X862go 🤖"Thank You"