Rick, I cannot thank you enough for the install video. Watched it several times and the install went perfectly. As you suggested, I checked all the ribbon cables and noticed the very small one on the right side was disconnected. Most likely happened when removing the antenna wire from the glued clips. Thanks again.
Nicely done. I've had a few comments on my ArgTek antenna video where viewers wished I explained the installation process more thoroughly. I'll be sure to refer them to this one. Excellent job. In fact, if I were you, I'd notify ArgTek so they could reference your video instead of the one that isn't in English on their website.
Hey thanks for the kind words. I had a few customers ask me about the installation so I thought I'd do a clip to explain it and save time. I appreciate you referring viewers to it if they need help with the installation. I just uploaded a clip on expanding their controller to 32-channels because this is the next thing they typically ask me about. I appreciate you stopping by.
ARGtek owes you some big thanks! Most P3-4 enthusiasts couldn't install this mod without your video. Be careful, though. Easy to buy and fly means dummies will try (mods) too.
Thanks a lot for the instructions, Rick. I was nervous about taking my controller apart, but this video gave me the confidence to do it. I had it playing from my laptop on one side of the desk, with all the little parts and screws on the other. I had a little trouble with removing the stock antennas and a couple other steps, but I was ultimately successful after a few hours.
Watched this video originally last month... broke down and ordered a set from dronevalley this week. Install was a bit nerve racking, and I found my hands do not like reinstalling ribbon line, but install completed! The basic control test was done to ensure the phantom still works as expected, and hope to do a range test tomorrow! Thanks for the informative video. It was my step-by-step all the way through.
Thanks a lot for the feedback and your business. I'm glad the video helped and every time someone tells me they've used it to guide the install it makes all the work worth it. You're going to love the upgrade and please let me know how you make out!
That's what I like most about it. I don't really care that it helps me fly 3 miles, I want a rock-solid signal in close and these deliver. I was flying out over the bay today and knowing the signal would stay consistent is the only reason I would travel that far out over the water.
Best video of this mod I've seen. After I get my P3S I plan to get familiar with it in it's stock configuration, then when I feel comfortable flying the P3S, I'll upgrade the antennas to the ARGtek antennas.
Thanks for posting that. The upgrades isn't that hard but takes a little patience. I agree with your plan to try it stock for a while before upgrading. When you do decide to take the plunge I sell these on our website (www.dronevalley.com) and you can use the code "Drone" for a discount when you're ready. Thanks again for watching and posting. Rick
This ARGtek system works well. Very easy to install. Took me a half a hour. Make sure you buy it through Ricks store so you don't end up with a knock off. I ended up adding 2 three Watt boosters on it. Getting 2 1/2 - 3 miles of strong Wi Fi. Sunhans makes a good booster.
Thanks for the encouragement, I hope you sub the channel. When you decide to buy the kit, check our site (www.dronevalley.com) and use the code "Drone" for a subscriber discount. Thanks again for watching.
Thanks again for posting. it's actually not that bad of an upgrade as long as you take your time. I'd avoid coffee as well since there are a lot of tiny screws that all want to find their way off the table you're working on if you have shaky hands :)
I appreciate the support and am glad you liked the clip. I'll have one more showing the difference it makes in signal strength when compared to the stock controller.
Thanks for the support and I'm glad you enjoyed the clip. The increase in distance is really dependent on how "noisy" the location is but in general I'm seeing more than double the distance I was able to fly before adding the kit. The other thing I love about them is that they provide a rock-solid signal when flying in close and allow me to fly in crowded areas without losing signal. They are easy to install and well worth the investment. I hope you sub the channel so you don't miss any updates.
The installation is much more challenging than appears to be in the video. The most challenging parts in the video are shown as before/after, removing antennas and wires was not easy. Full installation may take more than 2 hours. Also, with latest version of DJI GO, this antennas will work only in the allocated bandwidth of channels 13 to 20, it is no longer possible to activate all 32 channels unless you downgrade the DGI GO App. The video is very helpful, in the end of the day everything worked as expected.
Well 4 hrs. latter and I got it installed. I must have gotten the new improved cables (did'nt look anything like yours) because the outside cable where it pops to the brass fitting in would not fit! The end where it's taped up was real thick on both cables and the only way I could make it pop in was to cut the post where the one srew that holds the main board in by that contection. I tried to chissle a little notch out on the post but that still would not let me get that cable popped in. The other one was no problem. Not sure if I'll tackle any more projects like this. I never would have been able to do this had it not been for your video. Thanks for putting out your videos. I will check this out in the morning and let you know how I did.
Ray, I'm really sorry to hear that you had that much trouble installing the kit. I'm just curious if you bought it from us or somewhere else. I know there are a lot of "bootleg" kits out of China that look like the real thing but aren't the ARGtek original. We're an authorized ARGtek dealer and provide support after the sale so all of ours are straight from the factory. Please let me know and if it's ours I'll do all I can to sort it out for you. As a side note, the trick with getting the sleeve through the antenna hole is to slide the outer sleeve in from the top first and then the threaded part up through the bottom. A lot of people try and jam both up through the bottom and it can bind. Let me know how you made out and I'm glad the clip helped. Rick
Rick, I got it from amazon www.amazon.com/dp/B01BAH7EQO/ref=cm_cr_ryp_prd_ttl_sol_5 I had already had it before I found you on You Tube. Took it out today and thought I had messed up only to find out I was in a class D airport range. But before I found that out, GPS was not working on tablet so I couldn't get a home point set. Said "Safe to Fly GPS", I could only see half the map where I was at and it was blurry. Once I turned on the Data, map was working and then I got the DJI Go need to confirm that I could fly where I have always flown for the last 6 months. So whatever BlueProton is selling it's working fine on my P3P. I did'nt go any distance and had no video loss, so I must be gettin a good signal. Two questions for you: #1. I have always been under the assumption that the tablet should be in Airplane mode, no Data or WiFi on. #2. I live in a suburb of Phoenix and fly in open residential fields or city parks. I have done the 32 channel hack what do you suggest, Auto or one of the higher upper channels. Side note: I had no problem with the sleeves. It was the one wire antennae end that pops into the fitting by the Up & Down stick that you had to remove the screw to get it off in the video (14:18) And now that I've gone back and looked at the video (14:40) I see that the wire is over the srew that I left out and cut the post off to get my end wire to connect because I was tring to pop it on with it down beside the post. As much trouble as I was having with that one wire I wish now I would have just stopped and finished the install this morning with a fresh look at the video from the begining just as I have now. I don't think I have hurt anything as far as the stability of the main board. P.S. Where can I get one of those signal checkers like the one in your range test video. Thanks again, wish you sold on Amazon as I have a account with them I use just for the drone biz. Take care!
Ray, the company you bought it from (Blue Proton) are great guys and that is definitely a legit kit. That one screw is a pain because it's right in the way of the connection. it pops off with a little work but getting the new one in is a pain. Sounds like everything is working great for you now ao good luck with it. I actually leave Wifi and Bluetooth on when I fly and haven't had any issues so far so I'm not sure it's a big deal. That warning usually comes up when you're in a restricted area like a National Park or near an airport. If you pass the Part 107 test in September you won't have to worry about it with smaller (Class G) airports. The EMF meter is available from a lot of different vendors, even Amazon. Just be sure you find one that can cover the ISM band. Glad you got everything sorted and thanks again for supporting the channel.
Great video, very informative and helpful w/this mod. Got it all installed and buttoned up to find the altitude/rotation thumbstick getting stuck slightly in the up position. I had to pull the controller apart again. I found out the left antenna wire had popped up and was laying on the bottom mechanical part of that thumbstick. I repositioned it around and down and proceeded to wrap the controller up. Just as I went to put the bigger ribbon cable on the board I fumbled and twisted the cable, ripping it at the left side. BIG mistake, that cable is super delicate. I did a quick net search and found out the cable is NOT available and DJI wants you to send the controller back to them for repair. It would be great if DJI or someone else had this cable available knowing how many people mod the controllers antennae. I wound up hitting a popular "auction/purchasing" website and found people selling spare controllers. Snagged one for $140 w/shipping. I'm just going to get the cable from that one, and I'll only have to wait ~ 1 week before I can fly again and test this mod. I only flew my P4 three times before this mishap but managed to get a couple of video's I'm going to upload to my page soon.
Thanks a lot for sharing detailed instructions. I installed the ArgTek kit in my P4 today. To test the end result, I checked signal strength by removing the antenna panel one at a time. With only the left antenna on, I got full signal strength through several walls inside my home about 50 ft away. Surprisingly, with the only right antenna on, I only got 3 out of 5 bars in signal strength at the same distance and location. I'm wondering why left and right antennas would yield different signal strength?
Sunny, thanks for the post and those two antenna work in parallel with other to create the proper radiation pattern and you'll get weird results if either of them are damaged or missing. The transmitter is expecting to have both of them installed and you can actually damage the circuit if they are not installed. Kind of a cool experiment but don't do that too often so you don't hurt the remote. Thanks for posting and be sure to sub the channel if you haven't already so you don't miss any updates. Rick
Drone Valley Thanks for responding. I did the experiment to ensure both antennas were installed and working properly under the assumptions that each would work independently with same level of signal strength. Definitely will test this out to see if it will exceed my personal record of 13k ft with reflectors on stock antennas.
The kit I received has three sets of paddle antennas. One pair says 2.4GHz/5GHz 8dBi, the second pair says 5.8GHz 6dBi, and the third pair just says 7dBi. I have the Phantom 3 Professional. Which pair do I use?
Hi Rick ! TKS for the video. It works well but why do you use such thick antenna cables ? The are really difficult to install and find a place, where they can rest. Especially the connection between the plug and the cable is very thick. I had a lot of work to get them somewhere to sit. Why not installing the same thin cables and plugs like the original antennas ?
Hey there I have a DJI Phantom 3 now for years and it works perfectly the only thing is that the range isn’t as good as other drones but instead of buying a new drone I would like to try the range extender do you think it is still possible to buy these or are they from the last century and not available anymore? What do you think? Thank you for your answer
That sounds amazing and I'm glad you got it sorted out. I haven't tested the boosters yet but ARGtek is working on a kit that includes a set of them. I hope to be able to test it in a week or two. Rick
Great video my man anyway I have a important question I installed my antennas but my only doubt is when I went to put the bottom ribbon on from the circuitboard I can't tell how far it should go in before closing the little black. Should I see the little gold connectors or they should be further in thanks for any info because I have nothing it won't connect to the drone I have Gimber working recording working but just won't connect to antennas
I use a pencil eraser to push the connector in gently and it should seat in almost all the way. You also need to make sure you have it aligned correctly by checking to see that the edge of the connector is parallel to the connector. I had an issue with one of the upgrades because the cable was skewed in the connector. Try those suggestions and let me know how you make out and be sure to sub the channel so you don't miss any updates. Thanks, Rick
Thank you very much it worked scared me for a moment I thought I was going to have to buy another controller or return the Wi-Fi extenders back. But I got home from work and it went in all the way and the line was straight turn it on and it connected. 😃 how much further distance would I be able to go with these antennas I have the 32 channel mod and I use channel 22 is that the correct channel? OK thanks again I sub to you. If you get a chance go and check out my channel I have some pretty good videos. Hope to hear back from you.
Ok, i have gotten the Argtec Range Extender kit for my Dji Phantom3 Pro. I started the transmitter tare down & the module on the back, that has 3 ribbon cables on it, the 2 cables on the side of the module have come completely off the board. What can i do??? Please help, from what i can see, looks like i'll have to buy a new board or upgrade to the HDMI module, can these white tabs be reinstalled on the module board???
Yes, I do think its a good idea to modify the controller for a full 32-channels and here's a link to a clip I did showing you how to do that. Make sure you subscribe to the channel so you don't miss any updates. ua-cam.com/video/Yulgy1EEUW8/v-deo.html
Thanks for watching and I should have that clip up this week. The reason it was slightly delayed is that ARGtek just sent me a few new kits that expand the antenna and mounting options and I want to include them in the test. Look for it next week for sure. Please sub the channel so you don't miss anything and thanks again for posting.
Can you tell me why I do not show a large scale bar graph on my channel strength under the HD tab on the DJI GO app? My channels read out with just a tiny speck of light. I have no way of knowing which channel has the greater strength. I have seen this effect on other peoples videos but I have also seen the full range signals showing on other peoples videos. I am using an ACER 10 tablet and have NO OTHER issues other than this. I have re D/Led the app twice-no difference, I have looked through all settings for a possible solution but found none. I do have ARGtek antennas and 32 channels but this was happening before I made the mod. Does anyone have a hint as to why this is happening?
Thanks for posting and I wish I could help you figure it out. I've installed the DJI Go app on about 6 different devices (both apple and Android) and have never seen that issue. Is there any way you can install the app on another device to see if it works for you there? If it does than you have at least narrowed it down to an issue with the controller. Even if you borrow a friends phone to try it, you can always delete the app when you're done. Let me know how you make out and be sure to throw me a sub.
Problem solved! I borrowed a friends Iphone and d/led the DJI GO app on it. Everything worked! DJI also suggested using a recommended device. Time to shop for another device. Thanks for your help.
I'll probably buy the upgraded kit from you. So what your saying is the paddles aren't as good for long distance flights so for distance use the long antennas ?
It's the other way around. The square paddles are perfect for long distance flying and the thinner "rods" are perfect for Omni-directional coverage. I probably use the Omni-directionals about 60% of the time and the paddles only when I'm flying far away. Rick
Got the kit from you yesterday...well packaged and arrived super quick! I watched your installation video a couple times and then I proceeded to tearing my controller apart. You make it look easier than it is...for example the wires on the new antenna leads are twice a thick as the original wires and STIFF! I had to take the joystick control board out to make the "snap" on antenna connections. Also didn't like the cable routing options for the new wires going over the ribbon cables on the far right as you look at the board. Why do those antennas have to be cross connected on the board like that? It would have been so much easier to go directly to the same side connectors...that part makes no sense to me. I have to wait till I get home to test the flight and connections of all the controls...I think I was pretty careful and put things back the way they were...sort of lol. My advice to someone who is not comfortable working with small connectors in a fragile area...have someone do the mod for you. There is soooo much you could screw up inside the controller. Tiny little parts, ribbon cables, wire paths and connectors...I was able to do it, but I have been working with small electronics for 30 plus years. On a scale of 1 to 10 I would score this a 6 for technical difficulty, and an 8 for likely hood you will jack up your controller and have to send it back to DJI for a non warranty repair. I hope these antennas are worth it, I hope they help me gain an extra 2000 to 3000 feet of distance...my Phantom 3 Professional loses connection at about 1500 - 1700 feet at around 275 feet of elevation! That is super sucky! But I live in a highly populated area, and there are many forms of interference i'm sure. Now that I have these external sms connectors I can experiment with other higher gain antennas as well.
Thanks for the post and I agree that you need to take your time with the upgrade and avoid coffee at all costs before you start. It is a pretty straightforward upgrade but you need to take a delicate approach to the work since you're around a lot of sensitive parts. The cables are thicker to help reduce the radiation loss in the wires and deliver more of the signal to the antennas. The stock wires are thin with less shielding, which means there is a lot more signal lost in transit. I really appreciate the review and hope you stop back soon. Rick
please I would like to know if after the installation of the ARGtek Range Extender do you need to install any thing like soft ware on the drone before flying it?
Great instructional video! Being a person that does electronics repair at component level I see no reason to pull the small PCB (Printed Circuit Board) or disconnect the two ribbon cables on the sides. All you have to do is unlock and remove the large ribbon cable at the bottom of the PCB. Both of the small ribbon cables are connected to the button PCB's that are attached to the back half of the case (no need to unhook them) and the large ribbon cable is connected to the main board so that's the only one that needs to be disconnected.
Awesome tutorial and very thorough! Suppose I wanted to buy a kit through your websight store right now, when would expect it to ship and be delivered?
I can have it shipped tomorrow by First Class mail and it should arrive in a few days. You can also use the code "Drone" for a subscriber discount on the kit and we'll ship it for free. Thanks, Rick
Good to know. If I decide to upgrade I'll defiantly show support and buy through you! Couple quick questions. Not sure if you mentioned it and I missed it but is this mod 8dBi or 10dBi? Also what is the frequency on this mod, 2.4GHz...?
They are actually 7dBi and work for the full ISM band 2.4 GHz - 2.49 GHz so they cover all of the 32-frequencies the upgraded controller supports. Thanks for considering us if you do the upgrade.
Are the argtek cable connectors that stick out of the remote a proprietary size? I just did the Maxx uav itelite mod on my p3a and I'd like to use the argtek car antenna but I'm not certain if the argtek has an odd size connector. Do you know? Thanks!
Hey Rick. Quick question. I'm installing the ARG-tek range extender I bought from you. When I took the first panel off with the hex head screws one of the black snap locks on the left mini ribbon cable holder was missing. Do you think it would be ok to put a drop of hot glue on it when I re-assemble to make sure it doesn't pull out ??? Thanks for your input. Johnny J
Johnny, it's odd that it was missing and fortunate that it didn't work loose and cause you problems. Using a small dab of hot glue would do the trick to hold it in place and could be removed if needed later in case you have to unseat the cable. Thanks for your business and be sure to let me know how you like the extenders. Rick
Hey Rick, happy new subscriber here. I just got a P3A on black friday. Been having a blast with it thanks to your videos. Curious if you could do a before and after range test with these things? Debating buying em from you guys but curious how much it would improve my range over those parabolic reflectors. Thanks so much, love the channel
Casey, thanks a lot for the sub and I'm glad the clip are helping. I will work on a clip for the ARGtek extenders but the P3S is a little different than the P3P and P3A since it uses Wifi instead of LightBridge to connect to the drone. The ARGtek extenders are still better than the parabolic ones but I would suggest trying the folding parabolic's first to see if you get the distance you need. They are pretty inexpensive and might do the job for you and you can always upgrade later. Thanks again for the sub and the post, Rick
Yea, I have the P3A. The parabolics did add 50-60% greater range but there is a lot of foliage and trees in my neigborhood. Look forward to your range tests with the ARGteks. Keep up the good work.
hi there After seeing your video I ordered the same antenna kit and fitted it to my P4... On the firat flight I lost contact with drone within the first few minutes, less than 200 feet above and away from me, tried several times. firmware ok batteries ok, any ideas...j
Hey Rick. Installed the ARGtek boosts range (6000 foot test) but the video feed is very choppy even at close range even with almost full bars on the video. Any ideas. LITCHI screwed me on a upgrade, they took away my 32 channels. Now I'm down to 8 noisy channels like DJI GO app. FYI, I have transmission channels set on auto. Thanks Rick
Johnny, choppy video can either be a weak signal or a slow processor in the tablet/phone you're using on the controller. Since you have a good signal indication, I'm thinking it's your tablet. You can try reducing the video streaming size in the application to see if that helps or temporarily swap out the tablet with another device to see if it fixes the issue. Let me know how you make out. Rick
I have the Phantom 3 4k. I got the WIFI extender kit and started to install it. I have one question. One of my stock antennas has 2 wires, a black and a grey. Installing this kit I assume I put the new wire from the extender kit in the place where the grey one was. What about the black wire? will it affect anything by removing it?
Eric Duncan I just got a kit for my 4k as well... what do antenna do I use in the center bar? The kit came with a panel for the center and three stick type antennas? I'm confused
Rick,,,Question...Why is it that every time I put up my drone I can never get a good video signal it always cuts out and it does not matter where I am at when flying...Could it be a bad cord connection between the tablet and the controller causing it I am at a complete loss here..My video's are horrible because of this issue..It's happening even with the ARGtek Range Extender Kit bought from you...
Ken, thanks for the sub and I wish I could help with the snow :) I'm in Jersey and we get our share of it too so these will be a slow few months for outdoor flying once the white stuff shows up. Rick
Ok I just received my ArgTek Range Ext and I'm following your video for the installation but when I open my remote It's slightly different? I have two wires on the left side antenna as you look at the remote as shown in your video. Is there a way to send you a pic? I have an Insprie1 Pro.
Is there any way you can do an installation video for the alientech duo signal booster on the re released phantom 4 pro .. the remote is completely different than its original.
Rick. I'm looking to buy the ARGtek range extender from your site. 2 questions. 1 which kit do you recommend (I have a DJI PA3) You have 2 kits one with 2 sets of antennas I would probabaly just use the square paddles. @ your install video uses a Philips head and a hex head but the photo on your store only show a Philips head ?
Johnny, the choice is up to you which kit you like and I try and make it easy to upgrade later. The basic kit comes with the bases and all the installation tools you'll need to do the work. It also includes the long-range paddles. Those are great for flying long distances but are very directional. I also offer the Omni-directional antenna that you can buy in the PLUS kit or add later if you like. These are excellent for flying in close and greatly improve your signal strength in all directions. Another new item is the car kit that allows you to use either of these antenna from inside your car. I hope that helps with your decision but everything you'll need comes with the kit you purchase. Thanks, Rick
Well started to take the remote apart. The cables connected to the small board you mention to use you finger nail to unclip it. They have changed the design and have a little pull tab to take the ribbon cable out. I found this out too late after I broke the connector off the board. $280 mistake (ouch) so I purchase a new controller. So if anyone has bought a new P3Pro be careful not to make the mistake I made. Hopefully I can find someone who can fix the broken controller and have it for a spare.
I heard the transmitter power output for the P4 is 20% less than the P3P. With the range extender kit not having any 2.4 boost module in between controller and antenna, how does the extender actually get it's range? the panel shape? ... thanx
Thanks for watching and for the post. Actually the P4 has a slightly more powerful transmitter than the P3P. The P4 spec is 23dBm and the P3P is 20dBm so even a naked controller will give a slight distance advantage. This kit helps even further by replacing the stock omni-directional antennas with a set of high-gain paddles that provide an additional 7dBi of gain. The combination makes for a much longer flight and a stronger signal in close to help you overcome "noise" in the channel. I hope that helps and you sub the channel so you don't miss any updates.
hello I bought the antennas but I tried to activate the 32 channels in my dji go 4 but I can not activate them, I do not know if the updates of the application, the antennas work in the same way without the 32 active channels
What do you think about the ITElite Maxx extender? I have one coming with the clean install kit so no hole drilling. Have you used the dbs ITElite products? I hear theyre better than argtec. I have zero experience in this type of thing but my hope is that you're very in depth video can lead me to installing the dbs itelite. It should be pretty much the same, right? Any feedback you can provide to keep me from destroying my transmitter? Thank you, if so...!
It depends on which if the channels is noisy where I'm flying. What I typically do is use the standard 8 frequencies unless I'm having spotty connection issues and then I go into the "HD" screen to see which of the other 24 are strongest and manually select that one to use for flying. I hope that helps!
HI Rick - sure this has probably been asked before but I don't see it, I have a Phantom 4 Advance Plus, can I use these extenders on the plus controller ? I have heard you need to update your firmware with a hack which I believe doesn't work with the Plus controller? thanks in advance for your help
Unfortunately, once you open the controller you void the warranty on the controller. There is really no way of telling that you opened the case but it still voids the warranty. However, it doesn't void the warranty on the drone so the biggest part of your purchase is still protected. Thanks for stopping by and posting. Be sure to throw me a sub, I have a lot more clips coming.
Hi Rik, can give me your opinion on the following plz, i have a P4 with omni directional 8dbi argtek antennas on it, would i be better off with the 7dbi directional antenna which you show in this video would this give me improved range do you think, thanks for the videos too.
Yes, I use both and the flat panel antennas are great when I really need extra distance because they direct the signal far down-field. If you have the kit installed, I can sell you the flat panels that just attach to the same bases on the controller. I switch between those and the omni's depending on where I'm flying. Thanks for the post and be sure to sub the channel. Rick
I was thinking the same thing yesterday when I did the clip. I'll check with the company and can send you an update. Drop me a note (rick@dronevalley.com) and I'll send you an update. Rick
Hi again Rick. I own a P3S and a P3P. I own the ARGtek range extender for the P3S. I just bought the car kik from you with no antennas. Can I buy the kit for the P3P without antennas? If so please send another invoice so I my buy it. THANKS Mark.
Mark, shoot me an email (rick@dronevalley.com) and I can sort it out for you. The car kit is designed to fit the kit for the P3P, P3A and the P4. It won't fit the P3S because of the extra antenna.
my question is i upgraded to the phantom 4 advanced. Can i just bind my phantom 3 advanced remote to the phantom 4 quadcopter? it looks lie the remote controller is identical. i didnt want to go into my new phantom 4 remote just tought i would keep the mod on my old controller and bind it to the phantom 4 aircraft do you know if that would work?
I'm about halfway done with it. It's a lot more complicated than it seems, trying to film and sync up several cameras in the clip. I've filmed it three times and am still sorting out some editing issues in post. The short answer is that the reflectors provide about 50% more range overall and the ARGtek can more than double your range. Thanks for stopping by and I promise I'll have the clip done soon. Rick
Rick, I purchased the extenders from you, as well as the car mount suction cup. Do you sell a pair of coaxial extension cables to give more length to the roof mount? Would it even work?
Very good video indeed. Thx a lot. I also appreciate your "way of speaking". Even for non-english-native-speakers you articulate yourself always very clear. I just subscribed your channel today ;-) One question: I received an ArgTek Range Extender Kit yesterday and tried to check it before starting the installing procedure. I found out, that when I move the wifi planels, I can hear in both of them some "lose parts" shaking/moving in the inside. Is this normal? Could it be a transportation damage? I was a bit concered and opened slightly one of the penals to get a glimps inside. I could see that the metal plate is not fixed or glued onto the plastic housing but can slide freely on the four plastic bolts holding the housing together. So this is the sound I here, when I move the wifi panel around. What do you guys recomend in such a case? Thx in advance for any answer ... and keep on flying ;-)
Thanks for the support and I appreciate you watching. The rattling in the antenna paddles is annoying but shouldn't cause any problems with operation as long as the wire is attached securely inside of the antenna. You could add a little piece of foam inside the case if it really bugs you. Did you buy those from our website or somewhere else? I offer full support for anything we sell you and am more than happy to replace them if needed. Be sure to sub the channel.
I would start from scratch with both. Make sure they are fully charged, place the drone on a flat surface and turn it on, wait until you hear the initialization beeps and then turn on the controller and it should bind. If you're still having trouble, follow the initial binding process in the manual to pair them. I had this issue after one of the firmware updates and that fixed it for me. Be sure to sub the channel so you don't miss anything. Rick
Rick, I'm losing video at 1000 feet with the new ARG-tek. I have seen a lot of people on the internet with the same problem. I got video up to 2000 feet before the kit with parabolic boosters. Any suggestions or tricks. Am I missing something ? Your help is appreciated. Johnny J
Johnny, shoot me an email (rick@dronevalley.com) and we'll get it sorted. I would try swapping out the tablet/phone first to see if that has any effect. I'll look for your email. Thanks, Rick
I have a question. If you can please answer, I'd very much appreciate it. I installed the panels and cables. But I have a red light on my RC when I turn it on. However, when is start up my drone the light turns green. Is that normal? I haven't tried to fly yet. I just wanna make sure the red light issue is normal first. Thank you
Hello! I hesitate to bug you since this is clearly a video for DJI so apologies for going off topic, but you seem to know what's good for these things in watching this. Have you had the chance to pop open a controller for the Autel X Star Standard version that is purely wifi? I loose video connection pretty often, not sure if an upgrade would help that or not since the phone I use as a monitor isn't connected with a cable. If it could help that would be amazing. My model says it should go out a half mile but it doesn't, at least for me. Anyway, can this line of extenders help for an Autel X Star Standard? Thanks for your time!
No problem with going off topic, I'm happy to help. Technically these antenna will work with helping to extend the WiFi range of any quad but this kit is specifically tuned for the DJI P3A, P3P and P4. I spoke with ARGtek yesterday and they are expanding the kits they produce to include other models. I have a Yuneec Typhoon H kit coming this week and expect them to also do one for the Autel as well. Be sure to sub the channel so you don't miss any of the clips because as soon as I have it I will do a review of the Autel kit. Thanks, Rick
Drone Valley excellent thanks and I will check to make sure I subbed you the other day. Do you mind telling me what you mean by the kits are specially tuned to those DJI models? Are they seriously different enough between the models to matter in the end other then the lengths of the wiring and possibly the paddle hardware to connect them? It's hard to wait for a product that may not be made and not just pull the trigger on one and give her a shot. I will do my best to wait though. Really I need some added wifi connection stability between my cell, the controller and the drone. Without it I just don't have trust in the thing with it dropping signal all the time. Thanks again!
I have a Inspire1 Pro and I'm looking to purchase this kit. I saw your other video on 32 channel hack, I'm a bit confused because in that video you say that when enabled the system won't automatically use those extra channels and you would have to manually pick one, but I saw in the description by BlueProton who are selling these kits on Amazon, says "You should install a firmware update to increase your channels to 32 channels prior to installation." so is it necessary to have these extra channels in order for this kit to work?
The hack just allows you to add 24 more channels you can use to communicate with the drone. It's not a mandatory update and you can use the kit without it but it does help you to find a "clean" channel when you're in a particularly noisy area. It's an easy update to do and if you ever want to go back to the stock DJI Go application you can simply uninstall the application and reinstall it again and you'll go back to the original 12 channels. The kit is awesome and will really increase your flying distance. I hope that helps and you grab a kit and I hope you sub the channel as well so you don't miss any updates. Thanks, Rick
It looks like a decent directional panel for the price. The mounting is a little goofy but it's hard to attach things to the P3S without modifying the case. I am a little suspicious about the distance claims for a few reasons. First, the P3S uses Wifi for communications and the technology has built-in limitations and is very susceptible to noise. Secondly, maybe its me but I can't follow a drone more than a few thousand feet out so even if it made it out to 5 miles, I'd be violating the VLOS rule. I know that's a personal decision but the main advantage to me with these range extenders is the added connection strength they provide when flying in close. They help to overcome the noise that can cause you to lose connection. I like the ARGtek product because it does a great job, is less expensive and looks closer to "stock" on the controller. I hope that helps but let me know what you decide. Rick
Hi I have been a long time subscriber. You are my go to / how to channel. Well done video. One question. When installing the right side antenna wire did you just snake the wire or did you actually remove the other 3 screws on the stick controller module ?
Thanks for the sub and your support. When I do these installations I typically remove the other 3 screws to make it really easy. I have seen others do it by leaving the control stick in place and just routing the wires over the top of it but I always worry about nicking them later during use. The control stick comes out very easy so give that a try.
Hey Rick. Can I add 2 3Watt powered amps inline before the ARG-TEK antennas ? I think they are 2.4 or 2.7 ghz They are made for drones to increase your wifi signal
Tell me more about this. I am curious about getting these ARGteks and maybe adding the boosters later. Curious how you could add the boosters and still have the antennae attached to the controller. It is my understanding that the signal path could go from the controller, to the booster, then to the antennae.
Yea I get that, but just curious on what happens to the antennae. Do you have to remove them from the controller and then mount them to the booster or something? The logistics of sending the signal out the controller, into the booster, then back into the antennae is what confuses me. Did your team win?
Hey Rick, I love the channel and it is a wealth of knowledge. I am getting a P4P+ and wanted to know if you think having the Itelite DBS Phantom 4 Pro Antenna Range Extender is a good idea thanks for any feed back.
Hey! thanks again for sharing. Do you think this antennas would help out a Phantom 4 Pro while flying in a city where there´s some interference? I don´t care much about range, but I do care about not losing connectivity. I don´t fly more than 1 mile though. I heard the P4P comes with 2 frequencies, do you think that could solve the problem so I donñt have to touch the controller? thanks! :) And Happy New Year.
Charles, The inspire version is slightly different that the Phantom kit but I have them in stock. Shoot me a note at my email (Rick@dronevalley.com) and I can send along an invoice and ship it out today. Thanks for watching and please sub the channel if you haven't already.
great video. i was wondering if you can tell me something about buying a drone i am thinking about buying the phantom 3 but i was thinking ifnyou can tell me wich one to buy i dont need 4k or anything like that only good to fly and great camera quality. and i am open to phanton 2 thanks for the video.
Victor. Buy a Phantom 3 Advanced. It shoots in 1080 HD. You can find them cheap on Amazon now that the Phantom 4 has come out. I'm totally happy with my PA3. Check out my channel and you can see the quality of my videos. You can pick one up for less than $700.00 now. Buy a extra battery and lenses. Good Luck
If you have any questions that Rick can't answer feel free to contact me through my channel. DJI Phantom is the best bang for your buck. Trust me, don't buy anything beneath a PA3
Viktor, thanks for the post and I agree with Johnny. the Phantom 3 Advanced is the lowest of the Phantoms I would purchase. The biggest difference is the LightBridge technology that allows you to safely fly further. The Phantom 3 Standard is less expensive and uses Wifi connection to the quad, which really limits your flying distance considerably. That may not seem like a big deal initially but trust me as soon as you start flying the quad, you'll want to fly further. Here's a link to help you decide between the different models. Thanks again and I hope you sub the channel, Rick DJI Phantom Comparison Page - tinyurl.com/gls5zt6
Thanks for the post and these are designed for the Phantom 3P, 3A and Phantom 4 controllers. I am working closely with the manufacturer and expect to have one for the Autel X-Star very soon. Be sure to sub the channel so you'll know when they are released as I'll have a video posted to review them. Thanks, Rick
Sorry Rick, again I have searched for the DJI.configs app for the djigo app .All I find is websites showing me how to install after the down load of the file . Am I just looking over it? HELP
Paul, they will work with the inspire but I need to add one more cable to the kit for tethering the second controller. If you're in the market for one of them, send me an email (rick@dronevalley.com) and I'll sort you out. Thanks, Rick
The upgrade replaces both of the stock antenna and works for both frequencies. The clip I did was for the P4, P3P and P3A. I'll check to see if it works on the P3 4K and update this comment when I hear back from the manyfacturer. Thanks for stopping by.
Thank you for the reply. I would 'assume' that if it works for other wifi models, it 'should' work for the 4k. But we know what happens when you assume! :-) thanks again!
Sorry for the delay in responding but I did a little investigation and discovered that the P3 4K works on a different frequency than the P3A, P3P and P4. This extender is designed for transmitters in the 2.400 GHz to 2.483 GHz range. The P3 4K uses 5.725 GHz - 5.825 GHz so the antenna are tuned wrong for this spectrum. You could try one of the passive reflectors to help with distance but because the 4K doesn't use Lightbridge the video signal may still drop out at a shorter distance. I wish I had better news.
I did a few tests with it and am working on a clip. My experience is that the parabolic reflectors increase the range about 50% and these more than double it. Thanks for the sub and stay tuned. Rick
I got the advanced and would do this install if it truly helped. If you could run a test with the stock antennas and then with the Argtek that would be super cool! :)
The P3 4K works on a different frequency than the P3A, P3P and P4. This extender is designed for transmitters in the 2.400 GHz to 2.483 GHz range. The P3 4K uses 5.725 GHz - 5.825 GHz so the antenna are tuned wrong for this spectrum. You could try one of the passive reflectors to help with distance. I'll check with ARGtek to see if they make a kit for the P3 4K. Thanks for the question and be sure to sub the channel so you don't miss anything.
Thanks for the quick response! I have the reflectors they work but not to great i think overall its just hard flying on the wifi instead of the light bridge tech.
I agree with you and that was the most disappointing thing about that version of the phantom. The Lightbridge technology provides a much more powerful signal for the video, which means you can see farther. Even though you can still extend the flying range of the P3 4K with aftermarket products, it doesn't help if you're flying blind. The refectors sound like your best bet for now with that quad.
Notes: While this product does extend the range, the term "range extender" is usually used for active (powered) equipment. This product is only a higher gain antenna.
Outstanding instructional video! I completed this in less than a 1/2 hour. Thank you the tips and tricks you gave made this installation a breeze.
Rick, I cannot thank you enough for the install video. Watched it several times and the install went perfectly. As you suggested, I checked all the ribbon cables and noticed the very small one on the right side was disconnected. Most likely happened when removing the antenna wire from the glued clips. Thanks again.
Best video I have seen on the installation of this modification. Nothing left unsaid. Great job !!! Thanks
Nicely done. I've had a few comments on my ArgTek antenna video where viewers wished I explained the installation process more thoroughly. I'll be sure to refer them to this one. Excellent job. In fact, if I were you, I'd notify ArgTek so they could reference your video instead of the one that isn't in English on their website.
Hey thanks for the kind words. I had a few customers ask me about the installation so I thought I'd do a clip to explain it and save time. I appreciate you referring viewers to it if they need help with the installation. I just uploaded a clip on expanding their controller to 32-channels because this is the next thing they typically ask me about. I appreciate you stopping by.
Wow, great minds think alike. Hope you don't think I'm stalking you :)
Haha, not at all. Maybe in the future we could dream up some project to do collaboratively on both of our channels.
That sounds like a plan. Maybe we could do a live session on a topic and invite our subscribers. Give it some thought.
ARGtek owes you some big thanks! Most P3-4 enthusiasts couldn't install this mod without your video. Be careful, though. Easy to buy and fly means dummies will try (mods) too.
Thanks a lot for the instructions, Rick. I was nervous about taking my controller apart, but this video gave me the confidence to do it. I had it playing from my laptop on one side of the desk, with all the little parts and screws on the other. I had a little trouble with removing the stock antennas and a couple other steps, but I was ultimately successful after a few hours.
Watched this video originally last month... broke down and ordered a set from dronevalley this week. Install was a bit nerve racking, and I found my hands do not like reinstalling ribbon line, but install completed! The basic control test was done to ensure the phantom still works as expected, and hope to do a range test tomorrow!
Thanks for the informative video. It was my step-by-step all the way through.
Thanks a lot for the feedback and your business. I'm glad the video helped and every time someone tells me they've used it to guide the install it makes all the work worth it. You're going to love the upgrade and please let me know how you make out!
@@Dronevalley I just did it thanks on the Phantom 3 Pro, by the way I just subscribed on your channel
Good instruction no headache or stress of pausing and rewinding. Great job
Even with the line-of-sight requirements in place, that is SURE to get a really strong, reliable signal. Great! Thanks for posting.
That's what I like most about it. I don't really care that it helps me fly 3 miles, I want a rock-solid signal in close and these deliver. I was flying out over the bay today and knowing the signal would stay consistent is the only reason I would travel that far out over the water.
Best video of this mod I've seen. After I get my P3S I plan to get familiar with it in it's stock configuration, then when I feel comfortable flying the P3S, I'll upgrade the antennas to the ARGtek antennas.
Thanks for posting that. The upgrades isn't that hard but takes a little patience. I agree with your plan to try it stock for a while before upgrading. When you do decide to take the plunge I sell these on our website (www.dronevalley.com) and you can use the code "Drone" for a discount when you're ready. Thanks again for watching and posting. Rick
Great instructional video on this installation. Very concise and informative as are all your videos! Thanks!
Thanks for the in-depth video. God bless, love from Philly.
I'm very confident that I can do the upgrade after watching.
This ARGtek system works well. Very easy to install. Took me a half a hour. Make sure you buy it through Ricks store so you don't end up with a knock off. I ended up adding 2 three Watt boosters on it. Getting 2 1/2 - 3 miles of strong Wi Fi. Sunhans makes a good booster.
Thanks for the post and it's good to see you stopping by. Rick
Thank you for this video. It was very well done and was most helpful. It made installing my new antennas a breeze!!!
Excellent mod tutorial! Thanks for sharing! I look forward to picking up this range extender kit in the next couple of weeks.
Thanks for the encouragement, I hope you sub the channel. When you decide to buy the kit, check our site (www.dronevalley.com) and use the code "Drone" for a subscriber discount. Thanks again for watching.
Code has no effect on check out FYI!
Ordered anyway, Prop guards and Lens filters. Case was out of stock. :(
Superb presentation. Not for the timid.
Thanks again for posting. it's actually not that bad of an upgrade as long as you take your time. I'd avoid coffee as well since there are a lot of tiny screws that all want to find their way off the table you're working on if you have shaky hands :)
Definitely recommended demonstration for this modification easily explained. ..
I appreciate the support and am glad you liked the clip. I'll have one more showing the difference it makes in signal strength when compared to the stock controller.
+Drone Valley Upload this video soon please. Interested to see the results.
This was extremely helpful. Thanks so much. Time to test the range!
great video very Thero waiting to see your flight video of this the how much range you get over stock thks
Thanks for the support and I'm glad you enjoyed the clip. The increase in distance is really dependent on how "noisy" the location is but in general I'm seeing more than double the distance I was able to fly before adding the kit. The other thing I love about them is that they provide a rock-solid signal when flying in close and allow me to fly in crowded areas without losing signal. They are easy to install and well worth the investment. I hope you sub the channel so you don't miss any updates.
The installation is much more challenging than appears to be in the video. The most challenging parts in the video are shown as before/after, removing antennas and wires was not easy. Full installation may take more than 2 hours. Also, with latest version of DJI GO, this antennas will work only in the allocated bandwidth of channels 13 to 20, it is no longer possible to activate all 32 channels unless you downgrade the DGI GO App. The video is very helpful, in the end of the day everything worked as expected.
Gotcha. Thanks for the advice. You're my go to guy Rick. I appreciate it. Johnny J
Well 4 hrs. latter and I got it installed. I must have gotten the new improved cables (did'nt look anything like yours) because the outside cable where it pops to the brass fitting in would not fit! The end where it's taped up was real thick on both cables and the only way I could make it pop in was to cut the post where the one srew that holds the main board in by that contection. I tried to chissle a little notch out on the post but that still would not let me get that cable popped in. The other one was no problem. Not sure if I'll tackle any more projects like this. I never would have been able to do this had it not been for your video. Thanks for putting out your videos. I will check this out in the morning and let you know how I did.
Ray, I'm really sorry to hear that you had that much trouble installing the kit. I'm just curious if you bought it from us or somewhere else. I know there are a lot of "bootleg" kits out of China that look like the real thing but aren't the ARGtek original. We're an authorized ARGtek dealer and provide support after the sale so all of ours are straight from the factory. Please let me know and if it's ours I'll do all I can to sort it out for you. As a side note, the trick with getting the sleeve through the antenna hole is to slide the outer sleeve in from the top first and then the threaded part up through the bottom. A lot of people try and jam both up through the bottom and it can bind. Let me know how you made out and I'm glad the clip helped. Rick
Rick, I got it from amazon www.amazon.com/dp/B01BAH7EQO/ref=cm_cr_ryp_prd_ttl_sol_5
I had already had it before I found you on You Tube. Took it out today and thought I had messed up only to find out I was in a class D airport range. But before I found that out, GPS was not working on tablet so I couldn't get a home point set. Said "Safe to Fly GPS", I could only see half the map where I was at and it was blurry. Once I turned on the Data, map was working and then I got the DJI Go need to confirm that I could fly where I have always flown for the last 6 months. So whatever BlueProton is selling it's working fine on my P3P. I did'nt go any distance and had no video loss, so I must be gettin a good signal. Two questions for you: #1. I have always been under the assumption that the tablet should be in Airplane mode, no Data or WiFi on. #2. I live in a suburb of Phoenix and fly in open residential fields or city parks. I have done the 32 channel hack what do you suggest, Auto or one of the higher upper channels.
Side note: I had no problem with the sleeves. It was the one wire antennae end that pops into the fitting by the Up & Down stick that you had to remove the screw to get it off in the video (14:18) And now that I've gone back and looked at the video (14:40) I see that the wire is over the srew that I left out and cut the post off to get my end wire to connect because I was tring to pop it on with it down beside the post. As much trouble as I was having with that one wire I wish now I would have just stopped and finished the install this morning with a fresh look at the video from the begining just as I have now. I don't think I have hurt anything as far as the stability of the main board.
P.S. Where can I get one of those signal checkers like the one in your range test video. Thanks again, wish you sold on Amazon as I have a account with them I use just for the drone biz. Take care!
Ray, the company you bought it from (Blue Proton) are great guys and that is definitely a legit kit. That one screw is a pain because it's right in the way of the connection. it pops off with a little work but getting the new one in is a pain. Sounds like everything is working great for you now ao good luck with it. I actually leave Wifi and Bluetooth on when I fly and haven't had any issues so far so I'm not sure it's a big deal. That warning usually comes up when you're in a restricted area like a National Park or near an airport. If you pass the Part 107 test in September you won't have to worry about it with smaller (Class G) airports. The EMF meter is available from a lot of different vendors, even Amazon. Just be sure you find one that can cover the ISM band. Glad you got everything sorted and thanks again for supporting the channel.
Great video, very informative and helpful w/this mod. Got it all installed and buttoned up to find the altitude/rotation thumbstick getting stuck slightly in the up position. I had to pull the controller apart again. I found out the left antenna wire had popped up and was laying on the bottom mechanical part of that thumbstick. I repositioned it around and down and proceeded to wrap the controller up. Just as I went to put the bigger ribbon cable on the board I fumbled and twisted the cable, ripping it at the left side. BIG mistake, that cable is super delicate. I did a quick net search and found out the cable is NOT available and DJI wants you to send the controller back to them for repair. It would be great if DJI or someone else had this cable available knowing how many people mod the controllers antennae. I wound up hitting a popular "auction/purchasing" website and found people selling spare controllers. Snagged one for $140 w/shipping. I'm just going to get the cable from that one, and I'll only have to wait ~ 1 week before I can fly again and test this mod. I only flew my P4 three times before this mishap but managed to get a couple of video's I'm going to upload to my page soon.
Thanks a lot for sharing detailed instructions. I installed the ArgTek kit in my P4 today. To test the end result, I checked signal strength by removing the antenna panel one at a time. With only the left antenna on, I got full signal strength through several walls inside my home about 50 ft away. Surprisingly, with the only right antenna on, I only got 3 out of 5 bars in signal strength at the same distance and location. I'm wondering why left and right antennas would yield different signal strength?
Sunny, thanks for the post and those two antenna work in parallel with other to create the proper radiation pattern and you'll get weird results if either of them are damaged or missing. The transmitter is expecting to have both of them installed and you can actually damage the circuit if they are not installed. Kind of a cool experiment but don't do that too often so you don't hurt the remote. Thanks for posting and be sure to sub the channel if you haven't already so you don't miss any updates. Rick
Drone Valley Thanks for responding. I did the experiment to ensure both antennas were installed and working properly under the assumptions that each would work independently with same level of signal strength. Definitely will test this out to see if it will exceed my personal record of 13k ft with reflectors on stock antennas.
The kit I received has three sets of paddle antennas. One pair says 2.4GHz/5GHz 8dBi, the second pair says 5.8GHz 6dBi, and the third pair just says 7dBi. I have the Phantom 3 Professional. Which pair do I use?
Hi Rick ! TKS for the video. It works well but why do you use such thick antenna cables ? The are really difficult to install and find a place, where they can rest. Especially the connection between the plug and the cable is very thick. I had a lot of work to get them somewhere to sit. Why not installing the same thin cables and plugs like the original antennas ?
Hey there I have a DJI Phantom 3 now for years and it works perfectly the only thing is that the range isn’t as good as other drones but instead of buying a new drone I would like to try the range extender do you think it is still possible to buy these or are they from the last century and not available anymore? What do you think? Thank you for your answer
I would like to know is there a substitute for for dji phantom 3 standard battery? I see a few options I would like yours please. Thank you Wade
Hey Rick. Added 2 Sunhans 3W boosters to the Argtek. Easily getting 2 miles with clean WiFi. I would highly recommend the boosters. : )
That sounds amazing and I'm glad you got it sorted out. I haven't tested the boosters yet but ARGtek is working on a kit that includes a set of them. I hope to be able to test it in a week or two. Rick
Curious to see these as well
Just wondering if the omidirectional antennas or patch panels would be better for extended range? Thanks
Great video my man anyway I have a important question I installed my antennas but my only doubt is when I went to put the bottom ribbon on from the circuitboard I can't tell how far it should go in before closing the little black. Should I see the little gold connectors or they should be further in thanks for any info because I have nothing it won't connect to the drone I have Gimber working recording working but just won't connect to antennas
I use a pencil eraser to push the connector in gently and it should seat in almost all the way. You also need to make sure you have it aligned correctly by checking to see that the edge of the connector is parallel to the connector. I had an issue with one of the upgrades because the cable was skewed in the connector. Try those suggestions and let me know how you make out and be sure to sub the channel so you don't miss any updates. Thanks, Rick
Thank you very much it worked scared me for a moment I thought I was going to have to buy another controller or return the Wi-Fi extenders back. But I got home from work and it went in all the way and the line was straight turn it on and it connected. 😃 how much further distance would I be able to go with these antennas I have the 32 channel mod and I use channel 22 is that the correct channel? OK thanks again I sub to you. If you get a chance go and check out my channel I have some pretty good videos. Hope to hear back from you.
Ok, i have gotten the Argtec Range Extender kit for my Dji Phantom3 Pro. I started the transmitter tare down & the module on the back, that has 3 ribbon cables on it, the 2 cables on the side of the module have come completely off the board. What can i do??? Please help, from what i can see, looks like i'll have to buy a new board or upgrade to the HDMI module, can these white tabs be reinstalled on the module board???
Do u recommend increasing no. Of channel ? If so, do u have an instructional video on doing so?
Yes, I do think its a good idea to modify the controller for a full 32-channels and here's a link to a clip I did showing you how to do that. Make sure you subscribe to the channel so you don't miss any updates.
ua-cam.com/video/Yulgy1EEUW8/v-deo.html
hello great vid!! when will u show the difference between the stock antennas and upgrade
Thanks for watching and I should have that clip up this week. The reason it was slightly delayed is that ARGtek just sent me a few new kits that expand the antenna and mounting options and I want to include them in the test. Look for it next week for sure. Please sub the channel so you don't miss anything and thanks again for posting.
Can you tell me why I do not show a large scale bar graph on my channel strength under the HD tab on the DJI GO app? My channels read out with just a tiny speck of light. I have no way of knowing which channel has the greater strength. I have seen this effect on other peoples videos but I have also seen the full range signals showing on other peoples videos. I am using an ACER 10 tablet and have NO OTHER issues other than this. I have re D/Led the app twice-no difference, I have looked through all settings for a possible solution but found none. I do have ARGtek antennas and 32 channels but this was happening before I made the mod. Does anyone have a hint as to why this is happening?
Thanks for posting and I wish I could help you figure it out. I've installed the DJI Go app on about 6 different devices (both apple and Android) and have never seen that issue. Is there any way you can install the app on another device to see if it works for you there? If it does than you have at least narrowed it down to an issue with the controller. Even if you borrow a friends phone to try it, you can always delete the app when you're done. Let me know how you make out and be sure to throw me a sub.
Problem solved! I borrowed a friends Iphone and d/led the DJI GO app on it. Everything worked! DJI also suggested using a recommended device. Time to shop for another device. Thanks for your help.
I use the iPad 4 mini and the Nvidia Shield K1 if you're still looking for a new tablet. Both of the are great choices.
Thanks , I have a Nexus 9 on the way!
That should sort it out for you. Let me know how you like it!
I'll probably buy the upgraded kit from you. So what your saying is the paddles aren't as good for long distance flights so for distance use the long antennas ?
It's the other way around. The square paddles are perfect for long distance flying and the thinner "rods" are perfect for Omni-directional coverage. I probably use the Omni-directionals about 60% of the time and the paddles only when I'm flying far away. Rick
Got the kit from you yesterday...well packaged and arrived super quick! I watched your installation video a couple times and then I proceeded to tearing my controller apart. You make it look easier than it is...for example the wires on the new antenna leads are twice a thick as the original wires and STIFF! I had to take the joystick control board out to make the "snap" on antenna connections. Also didn't like the cable routing options for the new wires going over the ribbon cables on the far right as you look at the board. Why do those antennas have to be cross connected on the board like that? It would have been so much easier to go directly to the same side connectors...that part makes no sense to me. I have to wait till I get home to test the flight and connections of all the controls...I think I was pretty careful and put things back the way they were...sort of lol. My advice to someone who is not comfortable working with small connectors in a fragile area...have someone do the mod for you. There is soooo much you could screw up inside the controller. Tiny little parts, ribbon cables, wire paths and connectors...I was able to do it, but I have been working with small electronics for 30 plus years. On a scale of 1 to 10 I would score this a 6 for technical difficulty, and an 8 for likely hood you will jack up your controller and have to send it back to DJI for a non warranty repair. I hope these antennas are worth it, I hope they help me gain an extra 2000 to 3000 feet of distance...my Phantom 3 Professional loses connection at about 1500 - 1700 feet at around 275 feet of elevation! That is super sucky! But I live in a highly populated area, and there are many forms of interference i'm sure. Now that I have these external sms connectors I can experiment with other higher gain antennas as well.
Thanks for the post and I agree that you need to take your time with the upgrade and avoid coffee at all costs before you start. It is a pretty straightforward upgrade but you need to take a delicate approach to the work since you're around a lot of sensitive parts. The cables are thicker to help reduce the radiation loss in the wires and deliver more of the signal to the antennas. The stock wires are thin with less shielding, which means there is a lot more signal lost in transit. I really appreciate the review and hope you stop back soon. Rick
please I would like to know if after the installation of the ARGtek Range Extender do you need to install any thing like soft ware on the drone before flying it?
Great instructional video! Being a person that does electronics repair at component level I see no reason to pull the small PCB (Printed Circuit Board) or disconnect the two ribbon cables on the sides. All you have to do is unlock and remove the large ribbon cable at the bottom of the PCB. Both of the small ribbon cables are connected to the button PCB's that are attached to the back half of the case (no need to unhook them) and the large ribbon cable is connected to the main board so that's the only one that needs to be disconnected.
Awesome tutorial and very thorough! Suppose I wanted to buy a kit through your websight store right now, when would expect it to ship and be delivered?
I can have it shipped tomorrow by First Class mail and it should arrive in a few days. You can also use the code "Drone" for a subscriber discount on the kit and we'll ship it for free. Thanks, Rick
Good to know. If I decide to upgrade I'll defiantly show support and buy through you! Couple quick questions. Not sure if you mentioned it and I missed it but is this mod 8dBi or 10dBi? Also what is the frequency on this mod, 2.4GHz...?
They are actually 7dBi and work for the full ISM band 2.4 GHz - 2.49 GHz so they cover all of the 32-frequencies the upgraded controller supports. Thanks for considering us if you do the upgrade.
Are the argtek cable connectors that stick out of the remote a proprietary size? I just did the Maxx uav itelite mod on my p3a and I'd like to use the argtek car antenna but I'm not certain if the argtek has an odd size connector. Do you know? Thanks!
Hey Rick. Quick question. I'm installing the ARG-tek range extender I bought from you. When I took the first panel off with the hex head screws one of the black snap locks on the left mini ribbon cable holder was missing. Do you think it would be ok to put a drop of hot glue on it when I re-assemble to make sure it doesn't pull out ??? Thanks for your input. Johnny J
Johnny, it's odd that it was missing and fortunate that it didn't work loose and cause you problems. Using a small dab of hot glue would do the trick to hold it in place and could be removed if needed later in case you have to unseat the cable. Thanks for your business and be sure to let me know how you like the extenders. Rick
Great video, very helpful
Thanks for the post and I'm glad that you enjoyed the clip. I have a lot more content posting this weekend so be sure to sub the channel. Rick
Hey Rick, happy new subscriber here. I just got a P3A on black friday. Been having a blast with it thanks to your videos. Curious if you could do a before and after range test with these things? Debating buying em from you guys but curious how much it would improve my range over those parabolic reflectors.
Thanks so much, love the channel
Casey, thanks a lot for the sub and I'm glad the clip are helping. I will work on a clip for the ARGtek extenders but the P3S is a little different than the P3P and P3A since it uses Wifi instead of LightBridge to connect to the drone. The ARGtek extenders are still better than the parabolic ones but I would suggest trying the folding parabolic's first to see if you get the distance you need. They are pretty inexpensive and might do the job for you and you can always upgrade later. Thanks again for the sub and the post, Rick
Yea, I have the P3A. The parabolics did add 50-60% greater range but there is a lot of foliage and trees in my neigborhood. Look forward to your range tests with the ARGteks.
Keep up the good work.
hi there
After seeing your video I ordered the same antenna kit and fitted it to my P4... On the firat flight I lost contact with drone within the first few minutes, less than 200 feet above and away from me, tried several times. firmware ok batteries ok, any ideas...j
Hey Rick. Installed the ARGtek boosts range (6000 foot test) but the video feed is very choppy even at close range even with almost full bars on the video. Any ideas. LITCHI screwed me on a upgrade, they took away my 32 channels. Now I'm down to 8 noisy channels like DJI GO app. FYI, I have transmission channels set on auto. Thanks Rick
Johnny, choppy video can either be a weak signal or a slow processor in the tablet/phone you're using on the controller. Since you have a good signal indication, I'm thinking it's your tablet. You can try reducing the video streaming size in the application to see if that helps or temporarily swap out the tablet with another device to see if it fixes the issue. Let me know how you make out. Rick
I have the Phantom 3 4k. I got the WIFI extender kit and started to install it. I have one question. One of my stock antennas has 2 wires, a black and a grey. Installing this kit I assume I put the new wire from the extender kit in the place where the grey one was. What about the black wire? will it affect anything by removing it?
Eric Duncan I just got a kit for my 4k as well... what do antenna do I use in the center bar? The kit came with a panel for the center and three stick type antennas? I'm confused
Will these help prevent electrical interference or other interferences that may accur.
Rick,,,Question...Why is it that every time I put up my drone I can never get a good video signal
it always cuts out and it does not matter where I am at when flying...Could it be a bad cord connection
between the tablet and the controller causing it I am at a complete loss here..My video's are horrible
because of this issue..It's happening even with the ARGtek Range Extender Kit bought from you...
Nice video, also subscribed. Now make the snow go away! Happy Flying. GrampaKenCanada
Ken, thanks for the sub and I wish I could help with the snow :) I'm in Jersey and we get our share of it too so these will be a slow few months for outdoor flying once the white stuff shows up. Rick
Ok I just received my ArgTek Range Ext and I'm following your video for the installation but when I open my remote It's slightly different? I have two wires on the left side antenna as you look at the remote as shown in your video. Is there a way to send you a pic? I have an Insprie1 Pro.
MrZX1409 need to another antenna cable for inspire one.
Is there any way you can do an installation video for the alientech duo signal booster on the re released phantom 4 pro .. the remote is completely different than its original.
Rick. I'm looking to buy the ARGtek range extender from your site. 2 questions. 1 which kit do you recommend (I have a DJI PA3) You have 2 kits one with 2 sets of antennas I would probabaly just use the square paddles. @ your install video uses a Philips head and a hex head but the photo on your store only show a Philips head ?
Johnny, the choice is up to you which kit you like and I try and make it easy to upgrade later. The basic kit comes with the bases and all the installation tools you'll need to do the work. It also includes the long-range paddles. Those are great for flying long distances but are very directional. I also offer the Omni-directional antenna that you can buy in the PLUS kit or add later if you like. These are excellent for flying in close and greatly improve your signal strength in all directions. Another new item is the car kit that allows you to use either of these antenna from inside your car. I hope that helps with your decision but everything you'll need comes with the kit you purchase. Thanks, Rick
Well started to take the remote apart. The cables connected to the small board you mention to use you finger nail to unclip it. They have changed the design and have a little pull tab to take the ribbon cable out. I found this out too late after I broke the connector off the board. $280 mistake (ouch) so I purchase a new controller. So if anyone has bought a new P3Pro be careful not to make the mistake I made. Hopefully I can find someone who can fix the broken controller and have it for a spare.
I heard the transmitter power output for the P4 is 20% less than the P3P. With the range extender kit not having any 2.4 boost module in between controller and antenna, how does the extender actually get it's range? the panel shape? ... thanx
Thanks for watching and for the post. Actually the P4 has a slightly more powerful transmitter than the P3P. The P4 spec is 23dBm and the P3P is 20dBm so even a naked controller will give a slight distance advantage. This kit helps even further by replacing the stock omni-directional antennas with a set of high-gain paddles that provide an additional 7dBi of gain. The combination makes for a much longer flight and a stronger signal in close to help you overcome "noise" in the channel. I hope that helps and you sub the channel so you don't miss any updates.
hello I bought the antennas but I tried to activate the 32 channels in my dji go 4 but I can not activate them, I do not know if the updates of the application, the antennas work in the same way without the 32 active channels
The channel mod stopped working in jan 2019, do your research next time u pea brain
How you eliminate the warning pop-up window “Safety notification.” from iPhone 11 pro when you use DJI 3 Standard?
What do you think about the ITElite Maxx extender? I have one coming with the clean install kit so no hole drilling. Have you used the dbs ITElite products? I hear theyre better than argtec. I have zero experience in this type of thing but my hope is that you're very in depth video can lead me to installing the dbs itelite. It should be pretty much the same, right? Any feedback you can provide to keep me from destroying my transmitter? Thank you, if so...!
do u know the best signal channel to use on the phantom 4
It depends on which if the channels is noisy where I'm flying. What I typically do is use the standard 8 frequencies unless I'm having spotty connection issues and then I go into the "HD" screen to see which of the other 24 are strongest and manually select that one to use for flying. I hope that helps!
ok ill try that thx
Hi buddy do they work for phantom 3 standard!! Only going 1000ft away and loosing signal
HI Rick - sure this has probably been asked before but I don't see it, I have a Phantom 4 Advance Plus, can I use these extenders on the plus controller ? I have heard you need to update your firmware with a hack which I believe doesn't work with the Plus controller? thanks in advance for your help
I am assuming this voids the warranty if you still have one?
Unfortunately, once you open the controller you void the warranty on the controller. There is really no way of telling that you opened the case but it still voids the warranty. However, it doesn't void the warranty on the drone so the biggest part of your purchase is still protected. Thanks for stopping by and posting. Be sure to throw me a sub, I have a lot more clips coming.
very very well done my friend best video on this on this mod
Thanks buddy, that means a lot.
Hi Rik, can give me your opinion on the following plz, i have a P4 with omni directional 8dbi argtek antennas on it, would i be better off with the 7dbi directional antenna which you show in this video would this give me improved range do you think, thanks for the videos too.
Yes, I use both and the flat panel antennas are great when I really need extra distance because they direct the signal far down-field. If you have the kit installed, I can sell you the flat panels that just attach to the same bases on the controller. I switch between those and the omni's depending on where I'm flying. Thanks for the post and be sure to sub the channel. Rick
Hey there, will the PLUS kit work with the P4 Pro? I understand the P4 Pro can also use the 5Ghz range. Will this be compatible? -Thanks!
I was thinking the same thing yesterday when I did the clip. I'll check with the company and can send you an update. Drop me a note (rick@dronevalley.com) and I'll send you an update. Rick
Hi again Rick. I own a P3S and a P3P. I own the ARGtek range extender for the P3S. I just bought the car kik from you with no antennas. Can I buy the kit for the P3P without antennas? If so please send another invoice so I my buy it. THANKS Mark.
Mark, shoot me an email (rick@dronevalley.com) and I can sort it out for you. The car kit is designed to fit the kit for the P3P, P3A and the P4. It won't fit the P3S because of the extra antenna.
my question is i upgraded to the phantom 4 advanced. Can i just bind my phantom 3 advanced remote to the phantom 4 quadcopter? it looks lie the remote controller is identical. i didnt want to go into my new phantom 4 remote just tought i would keep the mod on my old controller and bind it to the phantom 4 aircraft do you know if that would work?
Rick have you made the comparison video yet?
I'm about halfway done with it. It's a lot more complicated than it seems, trying to film and sync up several cameras in the clip. I've filmed it three times and am still sorting out some editing issues in post. The short answer is that the reflectors provide about 50% more range overall and the ARGtek can more than double your range. Thanks for stopping by and I promise I'll have the clip done soon. Rick
Rick I'm not trying to be funny but 50% and double mean the same?
Rick, I purchased the extenders from you, as well as the car mount suction cup. Do you sell a pair of coaxial extension cables to give more length to the roof mount? Would it even work?
Very good video indeed. Thx a lot. I also appreciate your "way of speaking". Even for non-english-native-speakers you articulate yourself always very clear. I just subscribed your channel today ;-)
One question: I received an ArgTek Range Extender Kit yesterday and tried to check it before starting the installing procedure. I found out, that when I move the wifi planels, I can hear in both of them some "lose parts" shaking/moving in the inside. Is this normal? Could it be a transportation damage?
I was a bit concered and opened slightly one of the penals to get a glimps inside. I could see that the metal plate is not fixed or glued onto the plastic housing but can slide freely on the four plastic bolts holding the housing together. So this is the sound I here, when I move the wifi panel around. What do you guys recomend in such a case?
Thx in advance for any answer ... and keep on flying ;-)
Thanks for the support and I appreciate you watching. The rattling in the antenna paddles is annoying but shouldn't cause any problems with operation as long as the wire is attached securely inside of the antenna. You could add a little piece of foam inside the case if it really bugs you. Did you buy those from our website or somewhere else? I offer full support for anything we sell you and am more than happy to replace them if needed. Be sure to sub the channel.
Where can I buy this kit for the phantom 3 advanced in the UK?
Great videos, where did you get kewl looking short USB cable?
Thank You
I can turn on my drone using the controller manually after I replace them. But on my ipad it says disconnected. Can you help me?
I would start from scratch with both. Make sure they are fully charged, place the drone on a flat surface and turn it on, wait until you hear the initialization beeps and then turn on the controller and it should bind. If you're still having trouble, follow the initial binding process in the manual to pair them. I had this issue after one of the firmware updates and that fixed it for me. Be sure to sub the channel so you don't miss anything. Rick
Ah actually the ribbon connecting the con and main board is a bit loose. I've fixed them by sticking a double tape. Works well now :)
Rick, I'm losing video at 1000 feet with the new ARG-tek. I have seen a lot of people on the internet with the same problem. I got video up to 2000 feet before the kit with parabolic boosters. Any suggestions or tricks. Am I missing something ? Your help is appreciated. Johnny J
Johnny, shoot me an email (rick@dronevalley.com) and we'll get it sorted. I would try swapping out the tablet/phone first to see if that has any effect. I'll look for your email. Thanks, Rick
I have a question. If you can please answer, I'd very much appreciate it. I installed the panels and cables. But I have a red light on my RC when I turn it on. However, when is start up my drone the light turns green. Is that normal? I haven't tried to fly yet. I just wanna make sure the red light issue is normal first. Thank you
Hello! I hesitate to bug you since this is clearly a video for DJI so apologies for going off topic, but you seem to know what's good for these things in watching this. Have you had the chance to pop open a controller for the Autel X Star Standard version that is purely wifi? I loose video connection pretty often, not sure if an upgrade would help that or not since the phone I use as a monitor isn't connected with a cable. If it could help that would be amazing. My model says it should go out a half mile but it doesn't, at least for me.
Anyway, can this line of extenders help for an Autel X Star Standard?
Thanks for your time!
No problem with going off topic, I'm happy to help. Technically these antenna will work with helping to extend the WiFi range of any quad but this kit is specifically tuned for the DJI P3A, P3P and P4. I spoke with ARGtek yesterday and they are expanding the kits they produce to include other models. I have a Yuneec Typhoon H kit coming this week and expect them to also do one for the Autel as well. Be sure to sub the channel so you don't miss any of the clips because as soon as I have it I will do a review of the Autel kit. Thanks, Rick
Drone Valley excellent thanks and I will check to make sure I subbed you the other day. Do you mind telling me what you mean by the kits are specially tuned to those DJI models? Are they seriously different enough between the models to matter in the end other then the lengths of the wiring and possibly the paddle hardware to connect them?
It's hard to wait for a product that may not be made and not just pull the trigger on one and give her a shot. I will do my best to wait though. Really I need some added wifi connection stability between my cell, the controller and the drone. Without it I just don't have trust in the thing with it dropping signal all the time.
Thanks again!
James Warren
Chuck Martins, yes?
great demonstration
Thank you Robert. I've done a few of these and thought I'd put a clip together showing how to do them.
+Drone Valley 👍
I have a Inspire1 Pro and I'm looking to purchase this kit. I saw your other video on 32 channel hack, I'm a bit confused because in that video you say that when enabled the system won't automatically use those extra channels and you would have to manually pick one, but I saw in the description by BlueProton who are selling these kits on Amazon, says "You should install a firmware update to increase your channels to 32 channels prior to installation." so is it necessary to have these extra channels in order for this kit to work?
The hack just allows you to add 24 more channels you can use to communicate with the drone. It's not a mandatory update and you can use the kit without it but it does help you to find a "clean" channel when you're in a particularly noisy area. It's an easy update to do and if you ever want to go back to the stock DJI Go application you can simply uninstall the application and reinstall it again and you'll go back to the original 12 channels. The kit is awesome and will really increase your flying distance. I hope that helps and you grab a kit and I hope you sub the channel as well so you don't miss any updates. Thanks, Rick
Ok I was looking on your site Drone Valley.com and None of your kits list the Inspire1? I was looking at this kit. ARGtek Range Extender PLUS
"You're gonna have a Dickens of a time..." Great vid. Thanks for the chuckle.
Rick. What do you think of the IT-Elite range extender. Claims up to 5 miles of range. $110.00 on Amazon
It looks like a decent directional panel for the price. The mounting is a little goofy but it's hard to attach things to the P3S without modifying the case. I am a little suspicious about the distance claims for a few reasons. First, the P3S uses Wifi for communications and the technology has built-in limitations and is very susceptible to noise. Secondly, maybe its me but I can't follow a drone more than a few thousand feet out so even if it made it out to 5 miles, I'd be violating the VLOS rule. I know that's a personal decision but the main advantage to me with these range extenders is the added connection strength they provide when flying in close. They help to overcome the noise that can cause you to lose connection. I like the ARGtek product because it does a great job, is less expensive and looks closer to "stock" on the controller. I hope that helps but let me know what you decide. Rick
Thanks for your input Rick. Now I'm leaning to the Argtek again
Hi I have been a long time subscriber. You are my go to / how to channel. Well done video. One question. When installing the right side antenna wire did you just snake the wire or did you actually remove the other 3 screws on the stick controller module ?
Thanks for the sub and your support. When I do these installations I typically remove the other 3 screws to make it really easy. I have seen others do it by leaving the control stick in place and just routing the wires over the top of it but I always worry about nicking them later during use. The control stick comes out very easy so give that a try.
Hey Rick. Can I add 2 3Watt powered amps inline before the ARG-TEK antennas ? I think they are 2.4 or 2.7 ghz They are made for drones to increase your wifi signal
You can use a booster with the ARGtek kit and it should increase your range with the higher output. Rick
The trick to connecting the amps to the controller is 2 reverse polarity sma connectors available on E-bay
Tell me more about this. I am curious about getting these ARGteks and maybe adding the boosters later. Curious how you could add the boosters and still have the antennae attached to the controller. It is my understanding that the signal path could go from the controller, to the booster, then to the antennae.
Casey Give me a bit and I will tell you how I did it. Watching football game right now
Yes and you need a stand alone power supply 12V DC available from Rexuav
Yea I get that, but just curious on what happens to the antennae. Do you have to remove them from the controller and then mount them to the booster or something? The logistics of sending the signal out the controller, into the booster, then back into the antennae is what confuses me.
Did your team win?
Casey come over to my channel so we are not having this conversation on Ricks channel out of respect
Thanks! Just got mind installed.
Billy, thanks for the post and I hope the clip helped with the installation. Rick
When will you upload the range test with these antennas?
I dont know man still waiting
Hey Rick, I love the channel and it is a wealth of knowledge. I am getting a P4P+ and wanted to know if you think having the Itelite DBS Phantom 4 Pro Antenna Range Extender is a good idea thanks for any feed back.
Hey! thanks again for sharing. Do you think this antennas would help out a Phantom 4 Pro while flying in a city where there´s some interference? I don´t care much about range, but I do care about not losing connectivity. I don´t fly more than 1 mile though.
I heard the P4P comes with 2 frequencies, do you think that could solve the problem so I donñt have to touch the controller?
thanks! :)
And Happy New Year.
Do you have this Wifi upgrade kit for the inspire 1?
Charles, The inspire version is slightly different that the Phantom kit but I have them in stock. Shoot me a note at my email (Rick@dronevalley.com) and I can send along an invoice and ship it out today. Thanks for watching and please sub the channel if you haven't already.
Rick I have the Inspire1 Pro and I don't see any kits for my model?
great video. i was wondering if you can tell me something about buying a drone i am thinking about buying the phantom 3 but i was thinking ifnyou can tell me wich one to buy i dont need 4k or anything like that only good to fly and great camera quality. and i am open to phanton 2 thanks for the video.
Victor. Buy a Phantom 3 Advanced. It shoots in 1080 HD. You can find them cheap on Amazon now that the Phantom 4 has come out. I'm totally happy with my PA3. Check out my channel and you can see the quality of my videos. You can pick one up for less than $700.00 now. Buy a extra battery and lenses. Good Luck
If you have any questions that Rick can't answer feel free to contact me through my channel. DJI Phantom is the best bang for your buck. Trust me, don't buy anything beneath a PA3
Advanced
Viktor, thanks for the post and I agree with Johnny. the Phantom 3 Advanced is the lowest of the Phantoms I would purchase. The biggest difference is the LightBridge technology that allows you to safely fly further. The Phantom 3 Standard is less expensive and uses Wifi connection to the quad, which really limits your flying distance considerably. That may not seem like a big deal initially but trust me as soon as you start flying the quad, you'll want to fly further. Here's a link to help you decide between the different models. Thanks again and I hope you sub the channel, Rick
DJI Phantom Comparison Page - tinyurl.com/gls5zt6
very clear and informative video!! :D Thanks, I have a question. is it a must? that I Should relink the RC after the procedure?
will these work on the new Autel X-Star premium pro drones?
Thanks for the post and these are designed for the Phantom 3P, 3A and Phantom 4 controllers. I am working closely with the manufacturer and expect to have one for the Autel X-Star very soon. Be sure to sub the channel so you'll know when they are released as I'll have a video posted to review them. Thanks, Rick
I own the autel so if you need dimensions on those antennas let me know
Sorry Rick, again I have searched for the DJI.configs app for the djigo app .All I find is websites showing me how to install after the down load of the file . Am I just looking over it? HELP
Will these range extenders work on my DJI Inspire 1 ? I noticed someone else asked you but you did not answer !
Paul, they will work with the inspire but I need to add one more cable to the kit for tethering the second controller. If you're in the market for one of them, send me an email (rick@dronevalley.com) and I'll sort you out. Thanks, Rick
I only have one controller and the first gen Inspire 1 .
Is this upgrade for the wifi or Lightbridge controller - or both?Great video! I have the p3(4k), so if it's for the wifi, I'll be ordering one soon!
The upgrade replaces both of the stock antenna and works for both frequencies. The clip I did was for the P4, P3P and P3A. I'll check to see if it works on the P3 4K and update this comment when I hear back from the manyfacturer. Thanks for stopping by.
Thank you for the reply. I would 'assume' that if it works for other wifi models, it 'should' work for the 4k. But we know what happens when you assume! :-)
thanks again!
Sorry for the delay in responding but I did a little investigation and discovered that the P3 4K works on a different frequency than the P3A, P3P and P4. This extender is designed for transmitters in the 2.400 GHz to 2.483 GHz range. The P3 4K uses 5.725 GHz - 5.825 GHz so the antenna are tuned wrong for this spectrum. You could try one of the passive reflectors to help with distance but because the 4K doesn't use Lightbridge the video signal may still drop out at a shorter distance. I wish I had better news.
Thanks so much! I do you the 'reflectors' and they seem to help a good deal. I get choppy video from time to time, but it's not too bad. Thanks again!
You're welcome. Thanks again for the sub and let me know if you have other questions.
Thanks very much!
David, thanks for the post and I hope you sub the channel. I have a lot more content posting soon that you won't want to miss. Rick
I did subscribe, thanks. Was wondering if you tested the range with and without the kit to see if there was a substantial difference.
I did a few tests with it and am working on a clip. My experience is that the parabolic reflectors increase the range about 50% and these more than double it. Thanks for the sub and stay tuned. Rick
I got the advanced and would do this install if it truly helped. If you could run a test with the stock antennas and then with the Argtek that would be super cool! :)
Does this work on the Phantom 3 4k controller as well?
The P3 4K works on a different frequency than the P3A, P3P and P4. This
extender is designed for transmitters in the 2.400 GHz to 2.483 GHz
range. The P3 4K uses 5.725 GHz - 5.825 GHz so the antenna are tuned
wrong for this spectrum. You could try one of the passive reflectors to
help with distance. I'll check with ARGtek to see if they make a kit for
the P3 4K. Thanks for the question and be sure to sub the channel so
you don't miss anything.
Thanks for the quick response! I have the reflectors they work but not to great i think overall its just hard flying on the wifi instead of the light bridge tech.
I agree with you and that was the most disappointing thing about that version of the phantom. The Lightbridge technology provides a much more powerful signal for the video, which means you can see farther. Even though you can still extend the flying range of the P3 4K with aftermarket products, it doesn't help if you're flying blind. The refectors sound like your best bet for now with that quad.
Hi dose this system work on the dji phantom 3 4k??
Very nice video 😎 ✌🏼
Thanks slayer, I appreciate the visit. These are really working well.
will these work with the phantom pro 4?
Notes: While this product does extend the range, the term "range extender" is usually used for active (powered) equipment. This product is only a higher gain antenna.
I'm having trouble finding the firmware update? The link provided doesn't work