How to Swap Cruise Control into a Truck without Cruise | 1995 Ford F150
Вставка
- Опубліковано 8 лип 2024
- As the title states, in this video I will show you how to swap cruise control into your non-cruise OBS Ford Truck. Ford used all the same wiring harnesses in these trucks. So the swap is plug and play. For this swap you will need the following parts:
- Cruise control steering wheel
- Cruise control servo
- SPOUT plug
You can find these parts in junkyards or on eBay. Otherwise there are no new parts available that I am aware of.
These other parts are required for the full factory working setup.
- Master brake cylinder with cruise - amzn.to/3u8E7Tz
- Brake pressure sensor - amzn.to/3gFkkIy
- Cruise control Ford TSB Harness - www.ebay.com/itm/352470639821
#fordf150 #diy #obsford #cruisecontrol
🚧 Links:
- Steering wheel puller - amzn.to/3XEsSzW
- 2 jaw gear puller - amzn.to/3BfRGov
⏰ Time Stamps:
0:00 Intro
0:09 Disconnect battery
0:30 Installing the cruise control servo
1:40 Connecting the cruise control cable to the throttle body
2:12 Removing the airbag
3:43 Removing the steering wheel with a puller
5:00 Pulling the steering wheel
6:40 Installing the cruise control steering wheel
9:00 Brake pressure sensor info
9:50 Jumping the brake pressure sensor harness with SPOUT plug
10:40 Master brake cylinder install route
10:48 Ford Cruise Control TSB - Brake Pressure Sensor Harness Recall
11:37 Conclusion
Welcome to The Minute Masters UA-cam Channel where I (Stevie) show you how to repair and upgrade all Ford F series trucks and Broncos from 1980-1997. So hit that subscribe button and be ready to resurrect your baby!🤙
🚨🚨🚨Want to wear cool Minute Masters merch click this link👇
minutemasters.bigcartel.com
🔥Subscribe here: / theminutemasters
Links to my favorite product producers:
- desolatemotorsports.com/
- www.bubbarope.com/
- donttellmywiferacing.bigcarte...
- www.bajahidretrofits.com/
- capritools.com/
The project is my 1995 Ford F150 XL 2wd 8 foot bed.
🛍 As an Amazon Associate I earn from qualifying purchases. - Авто та транспорт
You're awesome! Keep these OBS videos coming. Been wanting to do this with my truck for awhile so this is helpful.
Thanks man!🤙
I absolutely love this channel. I like how you tell us what tools we need. Great stuff.
Thanks man!🤙 I appreciated it.
If you have an obs ford without cruise control, then it probably also does not have a tilt column. Column swaps are simple on these trucks and if you have a tilt donor just remove the column and install the whole column instead of pull the wheel. Get two upgrades with one job.
Good point! If I had found this steering wheel in a junkyard I could have gone that route.
Actually super helpful info! Thanks!!!
Thanks man!🤙 You’re welcome!
Another great video Steve 👍
Looking forward to part 2.
Good choice on the fused wiring loom alternative.
(45-55 lb/ft on steering wheel bolt)
Thanks Greg!🤙
Me too! I really want to pick up a power brake bleeder to speed up the process.
Thanks for the torque spec!
Good job Nice & Clean
Thanks man!🤙
Good job Stevie good job
Thanks Francisco!
LOL, I've been wanting to do this to my F250! Thanks for making this video. I look forward to part 2
You’ll have to check but I think they swap only works for gas engines. But I that doesn’t seem right.
@@TheMinuteMasters My truck is gas, it is a 5.8. I have the same plugs on the fender as you do. lol, I went outside and looked.
@@iamgriff Sweet! Then you can definitely do the swap.👌
As usual, another great diy tutorial Stevie!
Now all you need to do is locate a ford steering wheel emblem off I believe an earlier Ford F series truck or perhaps E Series van to glue it on over the molded emblem in the new steering wheel!
Thanks man!🤙
Ah! Good idea! I’ll have to keep an eye out for one.
This gave me a newfound appreciation for my factory installed cruise control even though I rarely use it. Luckily the harnesses are all the same. Surely this video would be 10x as long if they weren't haha.
I know, right! I use cruise a lot when I’m on the interstate. But you’re right this video would be super long if it was more involved.
Amazing video i will be putting cruise in my 1993 f150
Thanks man!🤙 Nice! You will love it.
THANKS A LOT, YOU MADE MY YEAR!!! YOU'RE THE BEST! I JUST BOUGHT A T-SHIRT!!! YOU DESERVED IT!!
You’re welcome man!🤙 Glad to hear it! Wow! I appreciate it. You might be the first this year! Did you buy it from the store tab on my channel?
@@TheMinuteMasters I don't know, I just clicked on the button you have here. I received an email confirmation from Spring.
@@zh9119 Sweet! That’s the right one. Thanks man!🤙
@@TheMinuteMasters Thank YOU. Let me ask you something, Does that Milwaukee ratchet has the ability to limit the torque as you wish? I'd like that tool but I don't want to break a thread.
@@zh9119 unfortunately, it doesn’t have the ability to reduce the torque. Milwaukee does make a torque wrench. That’s electronic and a ratchet but it’s super expensive.
If your steering wheel is from the same year, you just need one extractor. Anyway, that's not a big deal.
Awesome video I came across it as I need to replace my clock spring on my 95 w/o cruise control but it seems as if my local part store option only offers the clock spring with cruise control I’m assuming since you didn’t replace the cs it should be the same… what do you advise???
Yes, I left the clock spring and it worked with cruise.
There is little info on the internet about doing this. Thank you. I always wondered about the brake switch. Mine is a 93 and doesn’t have that.
Yeah it’s not a swap people have documented and I had a lot of people tell me it’s too difficult.
That short harness without the fuse in it is the updated harness for the updated sensor. That fuses harness isn’t available anymore. At least to my knowledge, I just had to get a sensor for a truck and they gave me the short harness and updated sensor
I had to buy the harness with the fuse off eBay. You may be able to get them from a Ford dealer but I haven’t tried that.
This video is making me itch... gotta go check out the local lkq.... but I'm curious I have a 4.9L and the 5spd will the swap still be the same if I have all the same wiring under the hood.
1995 F150 4.9L SC/SB 2WD
You’ll have to check but I don’t see why not. Ford liked using all the same parts to keep costs down.
He Steve is that play in your steering wheel play in the red top steering box or something else
That play is from the tie rod ends. They are toast and on my replacement list.
Off topic, I have a '94 F150 with a 4.9l. I need a new radiator, how can i tell if i have a 1 or 2 row radiator, and are they interchangeable? (i.e. i can use a 1 row instead of 2 row, and vice versa)
You should be able to all at the top and see. I kind of double it’s two. If your truck comes stock with a 2 row, then I wouldn’t reduce to a 1 row. You would lose cooling capacity.
thats great but what can be done if you have an aftermarket steering wheel that you want to keep
Good question. You could relocate the cruise control wire to a set of switches on the dash. You would need to disassemble the clock spring and wiring to do that.
Would this be the same process and connectors for a 2002 Ford Ranger 3.0?
I don’t know for sure but I don’t see why not.
So what if i have an f350 that’s has nothing on the steering wheel. It’s all plain XL. Would i be able to put a F150 steering wheel in it?
Do you have a horn on the steering wheel?
Great video. I have an 84 F150 with Sniper EFI installed (i.e different throttle body). It was originally carbureted. Is there still a way for me to add cruise control? Thank you!
Thanks man!🤙 Excellent question! Did the truck come with cruise control or are you trying to add it as a mod?
@@TheMinuteMasters it did not come with cruise control unfortunately. I hear/see that Rostra makes an universal electronic cruise control kit, so that seems to be one option. I'd ideally prefer an OEM route if possible, but since I ripped out the computer and put in a Sniper, seems that path may be closed?
@@josephdamiani1858 That may be your only path.
Hello I was able to find everything thing I need on eBay motors but I was having some trouble finding the spout plugs?
Any recommendations and where I could buy these
I found my extra spout plug at a junkyard.
I have a '96 XL. I finished the first part of the installation this morning (without replacing the brake master cylinder), replaced steering wheel, installed CC module, attached cable to throttle. I went to test it on the highway, very happy and excited! Nothing 😔I got the CC module from a junkyard, maybe that's the reason. I check all the fuses, all good. My truck has all the jumpers on connectors from factory. I'm still not sure what's the purpose of the connectors 10:07, you said the one underneath the relay box goes to the master cylinder sensor, but, the one by the driver's firewall, what's that for?. Both of them have the grey jumper from factory anyway.
So just to verify: the CC on these trucks isn’t like newer vehicles. There’s no indicator lights and it doesn’t kick in quite as fast. My first test drive felt like a failure because I didn’t know if the CC was even on. Anyhow, be sure to firmly press the “on” button and then firmly press “set”. Then give it a good 10 second for the cable to pull. If it doesn’t work try it again.
If you have done this, I would test the actually servo (box that actuates cable) and make sure it’s working. Sometimes the weather seal on them broke, and the gears inside would rust together.
@@TheMinuteMasters I'm 56, yeah, I remember them lol. Yes, that's a good idea, I'll check the gears. In the area were I live, the junkyard 1990s F-150s stock is very low, specially XLTs. I have alerts from junkyards all around. I'll check on eBay for another one. They're not cheap though. Thanks!
@TheMinuteMasters You're a genius, watching the video again (it was my fault that I just saw that), I realized the connector that is attached to the lower side of the fuse box 10:06, it has a blank spout connector instead of a real one like the one by the CC module (servo). I got one from a junkyard, today I installed it, IT WORKS! There is another video that the guy splices two of the wires at the harness that goes to the CC module (servo) they're the ones who are in the brake lights circuit, so every time the brake lights are ON, the CC will be cancelled. I also read that it is not safe to do that. Anyway, without having the master cylinder replaced with the sensor, when I brake, it is canceling the CC. Good!
I don't have your email, I just sent you a picture of me to your merchandise website, wearing the MM T-shirt at Cerro 21 (2,600 ft height) Esquel, Argentinian Patagonia today where we hiked with my family (I'm visiting them from US).
@@zh9119 Nice! I’ll have to go and look!🤙
Hey buddy, no idea how to message you and I apologize for the long message but, I’ve literally tried everything and I can’t figure out what the issue is with my speedometer. Whenever I go over 75 the speed needle jumps and when I finish driving at highway speeds my abs and brake light come on. I have rebuilt my speedo, replaced the abs sensor on the rear diff, replaced the pigtail that attaches to the abs sensor, and I checked, my truck doesn’t have a speed sensor on the transmission. No codes for the abs. Just that my front airbag sensor is not grounded. What would you recommend? Changing out the abs control module? I have a 94 f150 with the 5.0 engine 4x4
So you have read the codes and no codes are trigger for this problem?
Have you fixes the ground for the airbag sensor?
If you don’t have a VSS on the transmission then you should have one on the diff. I’d look at replacing that as well.
@@TheMinuteMasters i539 10 - separator code, 17 - front airbag sensor not grounded and 172 lackof heated oxygen sensor. No, I have not. I didn’t think that had anything to do with the speedo or abs.
@@brians2106 I would chase down that airbag sensor grounds. Ground are a weird thing in how they affect vehicles.
Does you truck have a Speedo cable?
CAN YOU DO ONE WITH WIRING THE LICENSE PLATE BULBS OR AT LEAST ONE SHOWING THE EXACT WIRE THAT THE WOULD CONNECT TO?
My rear bumper install video, has a short wiring diy for the license plate lights.
Do you have any starter solenoid, pick-up distributor videos?
I have a video on how to replace the starter which has the solenoid attached to it.
@@TheMinuteMasters thanks. I took the wires off a week ago, and forgot how they went.
@@crocsonletsgo9665 If I remember correctly the two wires to the starter are different sizes. I can’t remember the wires for the solenoid though.
Is there a way to do tilted steering on a non titled steering obs ford like yours?
Yes, you have to swap the entire steering column for a tilt steering wheel to your truck. Guys do it. So it’s definitely doable.
@@TheMinuteMasters are you going to?
You should try to do a manual to power window conversion… I ask you because your videos are so good and detailed! You definitely have a passion for this!
@@ashadowedsniper4619 Maybe in the future. So far the steering wheel height is just right for me.
@@ashadowedsniper4619 This is tempting but I’ll have to see. It will be an expensive conversion without a junkyard.
I recently done the cruise control conversion and now my ABS light stays on. Please help.
I would ready your codes and see what was triggered.
Figured it out. The Brake Master Cylinder float was stuck and all I did was lightly push on it until it came up. No more illuminated ABS light and Parking Brake light.
I have a question about this, maybe I didn't understand that part of the video, 10:24, I did that, the CC cancels every time I push the brake, that's perfect! but, I can't understand why they installed that release switch. Having that fire hazard even with the new fuse harness, is it necessary to install a new master cylinder with the switch?Anyway, As I said in another comment, you're a genius, you made my whole year!
To be honest, I’m not sure how the TSB harness prevents a fire unless having an inline fuse is the key.
The sensor in the master cylinder is just another safety measure.
So there are three ways to cancel cruise:
1) steering wheel switch
2) switch at pedal
3) sensor at master cylinder.
I think Ford installed the master cylinder sensor as a last ditch effort to cancel cruise in the event the other two systems failed.
@@TheMinuteMasters Great! that means I can leave it like that. Another horrible safety thing to consider on these OBS, the black plastic cover over the throttle bracket, it only has two small screws, if it's loose and moves over the throttle cables it'd act as a cruise control and there is no way to release it while driving. It happened to a friend of mine, he had to figure it out with the brakes and move right away to the shoulder and stop the engine after he was safe to do it. Scary.
@@zh9119 Interesting! I’ve thought about removing the cover since it really doesn’t look good.
@@TheMinuteMasters I agree, I think it is the cheapest and ugliest cover ever lol. I left it to keep it original but, it's horrible.
I just installed cruise control because of this video! Works great! However, no lights to indicate CC is on or in use. Perhaps steering wheel should illuminate CC buttons? 1996 F-150. Thank you.
Great to hear man!🤙 Unfortunately, there is no indicator light showing the cruise control is on. I think that’s all Ford thought people needed.🤷♂️
Nice ascot.
Fashionable and functional!👌
@@TheMinuteMasters Downright dapper.
@@borderlineiq Thanks Jason!🤙
Hi Do you need some great lighting for your car to help you better driving, off-road? We're the pro auto lighting company for nearly 20 year and we're looking for sponsorship!
I just DMed you back on Instagram🤙
@@TheMinuteMasters Sure Let's chat!
Any idea where I can actually get my hands on a half decent cruise control steering wheel that doesn't look like it was used by an axe murderer? Everything on ebay is hot garbage.
Honestly the junkyard or a friend is your best bet. I bought this steering wheel off eBay for $140 and it looks like a squirrel chewed it in a few spots. This was one of the best looking on eBay too.
Do you have Twitter? I’d like to follow you on there
I don’t but I’m on TikTok and Instagram.
Cruise control???
Yup! I daily drive my truck and I often go some decent distances.
@@TheMinuteMasters I got a 95 f250 that I want to add cruise control. Do you have a video that shows how? This one's about coil springs.
@@jayfromtexas6718 do you have a gas engine?
@@TheMinuteMasters yes, 351ci
@@jayfromtexas6718 perfect! You should be able to do this swap.