Thanks so much for posting this. I just installed mine before finding your video. Like me, you probably just watched snippets of Chinese videos with brief flashes of video to figure it out. I hard wired mine as well and sort of fumbled my way through the alignment. It wasn't exactly a linear process with the adjustment screws. I am SO happy not though to have the dot inline with the laser beam. No more misaligned dots due to the severe angle. Again, thank you very much, I know many people will find this very helpful!
Thank you, that’s very kind. I’ve been very happy with mine so far as well. As you pointed out, the adjustment screws on the combiner were the most difficult aspect to figure out. Based on the limited instructions that are available, it was 100% trial and error on how to get the laser beam aligned into the mirrors correctly. Someone could do a video just on that process alone. That was definitely a head scratcher!!
Great video, thanks!! I'm not sure which side of the machine your wires are routed through, but mine route back through the left side of the machine as your looking at it and run back across to the controller and power supply. If that's the case you can just clip the wires going to the factory red dot and reroute them back to the new red dot and make your connection there with having to route the new wires.
Great insight. My power supply is to the right hand side as you face the machine, and so far, everything is working great. Fingers crossed! Thanks for the comment.
@@FlashpointWoodworks-fp6br My power supply is also on the right but the wiring for my red dot and auto focus run across the back of the machine and enter the gantry on the left side. I just hooked mine up yesterday just trying to get everything aligned again! I guess when I moved the tube backwards to make room for the red dot it through off the alignment on the laser!
@@FlashpointWoodworks-fp6br well an update on my install of this unit! My issues with alignment had nothing to do with the install of the red dot! However when installed my red dot ended up on the tube in the exact same way yours did which puts the alignment screws on the bottom very inaccessible! So to adjust the alignment of the red dot you have to loosen in to get to the screws make the adjustment and tighten it back into position. During this process the very tiny wires broke completely where it comes out of the unit! Be very careful with those wires they're very fragile! The worst part is you have to move them back and forth so much just screwing it on to the tube!
@@richardmccabe270 That was exactly my experience, minus the breaking of the wires. I think I just got lucky! For the laser tube itself to be positioned where it's supposed to be (water outlet tube pointed up for bubble escape), when the red dot is tightened down, the alignment screws are on the bottom (making them impossible to access. That's why it took me about an hour to finally get the red dot aligned with mirror #3. Now I'm not an engineer by trade, but it seems to me that if the threads on the beam combiner were just a bit shorter or longer, it would align better and make the entire process that much simpler. But what do I know...LOL
@@FlashpointWoodworks-fp6br you could put a few wraps of thread tape on the threads to thicken them, they will engage earlier and the red dot housing will be snug. adjust the amount of tape as necessary to get it positioned how you want it
some thing I just found out that the power supply is all ways on, make sure that all power is off when not in use. I lost my power supply with only about 50 hrs of cutting in 1 year
I have a laser with a Yongli tube that comes with this stock. It makes my other 2 laser jealous. I would love an adapter for Reci and other tube manufacturers, it's a really good tube. Not only for aligning the mirrors, also for framing the work pieces
LOL, I know exactly what you mean..."makes my other 2 lasers jealous"!! It's a great tool, once it's in place and dialed in properly. To your point, I just used mine again this morning using the Lightburn camera screen shot. The red dot was exactly where I placed it, while using the Lightburn software and the camera. Makes the job so much quicker and simpler.
Great Video! I have not yet bought a laser, so i was wondering what the difference is between the factory installed red dot and the beam combiner? Is it the accuracy? Thanks.
Thanks! Yes, since the beam combiner actually attaches to the laser tube, once you have it dialed in, it should be much more precise than those that come installed from the factory. Oftentimes, the ones installed at the factory can be easily bumped, therefore requiring much more frequent adjustments!
So I simply used the stock air pump to supply the air for the beam combiner since I have an aftermarket air system that I use with the laser itself. It only requires a few psi to keep the beam combiner cool and clear of debris. So far, the stock air pump has been plenty sufficient. Thanks for the question!
Great Video. I've had my 80W Monport with a Yongli tube for a month, and my only gripe has been the accuracy of the red dot. This accessory looks great. Question- did you hook up the air cooling line, or just leave it out? thanks
Thank you! So I actually rerouted the supplied air hose for the nozzle, and connected it to the beam combiner. I then used my aftermarket air system to provide air for the lens and laser nozzle.
The beam combiner, once correctly aligned, provides a more consistent ‘red dot’ than the factory installed red dot devices. The air inlet aids in keeping the beam combiner lens cool and combatting dust accumulation. I rerouted the factory air supply to the beam combiner and I use the after market air supply for the laser head assembly.
What size your laser? I just got the MF2028 100 watt and I really wanted to install this. But shows it is only compatible with the AF2440-100 - 100W, AF3555-130 - 130W and the AF4063-150 - 150W. I assumed because of the distance between the tube and mirror one. Thx
My machine is also the MF2028, but it is the 80w machine, and not the 100w. That may be the difference. I had enough space to install the beam combiner and still have the metal protective cover installed on the other end of the laser tube.
@@smattt Since my laser tube came in a box to install when the laser arrived. I believe there is definitely room to push the laser tube back for this to fit. My home monport 80 W I installed the bin combiner with a replacement near one and used the power to the red dot to power the beam combiner so I'm trying to figure out if this will do the same thing instead of using a battery pack. Get the battery pack and how long do they last
Oh, it’s right around 1 5/8” long or so! They may have the exact measurements on the OMTech website, but I didn’t go and look. I just measured mine real quick…
Thanks so much for posting this. I just installed mine before finding your video. Like me, you probably just watched snippets of Chinese videos with brief flashes of video to figure it out. I hard wired mine as well and sort of fumbled my way through the alignment. It wasn't exactly a linear process with the adjustment screws. I am SO happy not though to have the dot inline with the laser beam. No more misaligned dots due to the severe angle. Again, thank you very much, I know many people will find this very helpful!
Thank you, that’s very kind. I’ve been very happy with mine so far as well. As you pointed out, the adjustment screws on the combiner were the most difficult aspect to figure out. Based on the limited instructions that are available, it was 100% trial and error on how to get the laser beam aligned into the mirrors correctly. Someone could do a video just on that process alone. That was definitely a head scratcher!!
Thankyou ever so much for your presentation it was first class and made life so much easier for this Red Beam installation🌝
You’re welcome. I’m so glad you found the video useful. Thanks for letting me know!
Thank you for this video, helped give me some courage to install mine, going to try it this week.
Good luck! Glad you enjoyed the video. The process was fairly straightforward.
Great video, thanks!! I'm not sure which side of the machine your wires are routed through, but mine route back through the left side of the machine as your looking at it and run back across to the controller and power supply. If that's the case you can just clip the wires going to the factory red dot and reroute them back to the new red dot and make your connection there with having to route the new wires.
Great insight. My power supply is to the right hand side as you face the machine, and so far, everything is working great. Fingers crossed! Thanks for the comment.
@@FlashpointWoodworks-fp6br My power supply is also on the right but the wiring for my red dot and auto focus run across the back of the machine and enter the gantry on the left side. I just hooked mine up yesterday just trying to get everything aligned again! I guess when I moved the tube backwards to make room for the red dot it through off the alignment on the laser!
@@FlashpointWoodworks-fp6br well an update on my install of this unit! My issues with alignment had nothing to do with the install of the red dot! However when installed my red dot ended up on the tube in the exact same way yours did which puts the alignment screws on the bottom very inaccessible! So to adjust the alignment of the red dot you have to loosen in to get to the screws make the adjustment and tighten it back into position. During this process the very tiny wires broke completely where it comes out of the unit! Be very careful with those wires they're very fragile! The worst part is you have to move them back and forth so much just screwing it on to the tube!
@@richardmccabe270 That was exactly my experience, minus the breaking of the wires. I think I just got lucky! For the laser tube itself to be positioned where it's supposed to be (water outlet tube pointed up for bubble escape), when the red dot is tightened down, the alignment screws are on the bottom (making them impossible to access. That's why it took me about an hour to finally get the red dot aligned with mirror #3. Now I'm not an engineer by trade, but it seems to me that if the threads on the beam combiner were just a bit shorter or longer, it would align better and make the entire process that much simpler. But what do I know...LOL
@@FlashpointWoodworks-fp6br you could put a few wraps of thread tape on the threads to thicken them, they will engage earlier and the red dot housing will be snug. adjust the amount of tape as necessary to get it positioned how you want it
some thing I just found out that the power supply is all ways on, make sure that all power is off when not in use. I lost my power supply with only about 50 hrs of cutting in 1 year
That’s a great reminder. Thanks for posting it!
Thank you for this video. Subbed!
Thanks for the sub!! I’m glad the video was useful. 🫡
I have a laser with a Yongli tube that comes with this stock. It makes my other 2 laser jealous. I would love an adapter for Reci and other tube manufacturers, it's a really good tube. Not only for aligning the mirrors, also for framing the work pieces
LOL, I know exactly what you mean..."makes my other 2 lasers jealous"!! It's a great tool, once it's in place and dialed in properly. To your point, I just used mine again this morning using the Lightburn camera screen shot. The red dot was exactly where I placed it, while using the Lightburn software and the camera. Makes the job so much quicker and simpler.
@@FlashpointWoodworks-fp6br I'm thinking of 3d printing an adapter. Maybe with the air assist it won't get too hot
@@sebamop Oooo, game changer alert! Keep me updated, if you do. I'd be interested in checking it out!
Great Video! I have not yet bought a laser, so i was wondering what the difference is between the factory installed red dot and the beam combiner? Is it the accuracy? Thanks.
Thanks! Yes, since the beam combiner actually attaches to the laser tube, once you have it dialed in, it should be much more precise than those that come installed from the factory. Oftentimes, the ones installed at the factory can be easily bumped, therefore requiring much more frequent adjustments!
HI thanks for the video, where do you connect the air inlet and how much psi is required. does this require a second air pump?
So I simply used the stock air pump to supply the air for the beam combiner since I have an aftermarket air system that I use with the laser itself.
It only requires a few psi to keep the beam combiner cool and clear of debris. So far, the stock air pump has been plenty sufficient. Thanks for the question!
Great Video. I've had my 80W Monport with a Yongli tube for a month, and my only gripe has been the accuracy of the red dot. This accessory looks great.
Question- did you hook up the air cooling line, or just leave it out? thanks
Thank you! So I actually rerouted the supplied air hose for the nozzle, and connected it to the beam combiner. I then used my aftermarket air system to provide air for the lens and laser nozzle.
Now that you have had it for two months was it worth it?
Yes, 100%. I have zero regrets, and the consistency is undeniable!
What exactly does this component do? Also, what is the purpose of the air inlet in it?
The beam combiner, once correctly aligned, provides a more consistent ‘red dot’ than the factory installed red dot devices.
The air inlet aids in keeping the beam combiner lens cool and combatting dust accumulation. I rerouted the factory air supply to the beam combiner and I use the after market air supply for the laser head assembly.
What size your laser? I just got the MF2028 100 watt and I really wanted to install this. But shows it is only compatible with the AF2440-100 - 100W, AF3555-130 - 130W and the AF4063-150 - 150W. I assumed because of the distance between the tube and mirror one.
Thx
My machine is also the MF2028, but it is the 80w machine, and not the 100w. That may be the difference. I had enough space to install the beam combiner and still have the metal protective cover installed on the other end of the laser tube.
@@FlashpointWoodworks-fp6br Thx, I'm ordering mine. This is much easier than the replacement mirror one - beam combiner I have on my Monport 80 watt
@@darlalynw I'm in the same situation - I have the 100W MF2028 and I have to see if it'll fit. I hope it does.
@@smattt Since my laser tube came in a box to install when the laser arrived. I believe there is definitely room to push the laser tube back for this to fit. My home monport 80 W I installed the bin combiner with a replacement near one and used the power to the red dot to power the beam combiner so I'm trying to figure out if this will do the same thing instead of using a battery pack. Get the battery pack and how long do they last
How long is the beam combiner?
Oh, it’s right around 1 5/8” long or so! They may have the exact measurements on the OMTech website, but I didn’t go and look. I just measured mine real quick…
@@FlashpointWoodworks-fp6br thanks!