Need a ball joint out? Big Nasty. Brake rotor stuck on hub? Big Nasty. Need to add a few degrees of camber? Big Nasty. Need to remove a blown fuse? Big Nasty. Change the radio station? Big Nasty. Anniversary gift for the wife? Big Nasty. I'm telling you, it DOES do it all :P
Big Nasty would be A LOT... LOT more useable if only it had a better trigger. A nice feather trigger would make it the only air hammer you'd need. But when I'm doing an alignment on a Ford or Dodge truck and I'm trying to remove a Camber/Caster bushing I DO NOT always need or want full throttle balls out power of Big Nasty. Same goes for when I need to finesse a bushing out or just start to chisel something out nice and easy at first. I think I'm gonna have to get the high-flow air fittings for my Snappy air gun.
I have a Chicago Pneumatic CP715 that I bought new in the early 80's from Sears (I own mostly CP and IR air tools). The CP715 is still in great shape. I run it with the automotive-type high flow air fittings (as I do all my air tools) but I'm going to upgrade it with a quick release chuck and finally dump the spring. Not a tool that I use all that often as a non-pro, but when you need it, that long stroke hammer is gold. I have been finding myself using it more and more though. One thing to keep in mind with the big, long stroke .498 air hammers (like Big Nasty) is that they are really air hungry. I'm talking like 13cfm@90psi hungry. Yeah, that is the actual running, balls to the wall air consumption of the CP717 (and likely the AP 4980, since it is basically a copy of the CP717). Don't be fooled by the low average air consumption numbers you might see elsewhere, that is kinda like EPA highway mileage. You need like 3x that airflow to really get the full potential out of this tool, as well as at least a 3/8" air line and high flow coupler and fittings. Will it "work" on less? Yes, but not at the performance levels for which it was designed. Which means you could be disappointed in the results. I was looking at them, and quickly realized that although my ailines and fittings are good, my 60 gallon single stage IR reciprocating compressor cannot provide the airflow this beast wants, even at 100% duty cycle (which it is clearly not designed for). This is probably not going to be an issue for most pros in shops with two-stage monster cast-iron compressors, but may be for most DIYers and mobile pros.
I can't believe there wasn't a "hammer time " thrown in there somewhere , nice job mike .trigger went out on my ir a few years ago it cost me a dime to replace the o rings and it's still going strong
When I got started I bought the $38 Ingersoll from Amazon since there were already 3 Snap On air hammers in the shop and surprisingly enough I haven't had to borrow one of them yet. Ive used that thing every day for the last 2 years on ball joints, roll pins, and cv axles on ATVs and I swear it's only gotten stronger with time. I have also seen it outlast 1 Matco so far. For the money it's probably my favorite tool purchase. If it fails I'll probably get a snap on or a larger IR but I can definitely recommend the 114GQC model for a budget gun. I did however buy certain bits from Ebay made by Mayhew. They make Snap Ons punches as well as a lot of other tool truck tools.
I have a ingersoll air hammer, I think it was 70 or 80 bucks, but the thing is amazing, and the good thing with IR is that you can buy replacement parts for them when they do break. I don't know how I did anything before I got an air hammer.
90% of my air hammer use is for ripping old exhaust apart, so I don't need a monster. Suprisingly, my cheap Campbell-Housfield (from K Mart!) has lasted 20 years.
I've used a monster 30 year old Chicago Pneumatic that is about 2 foot long. Insanely powerful still. It will cut car frames in half with 3/4 trigger pull. But will exhaust you in about 1 minute of usage.
I bought the snap on ph 3050 b. I got it at a very reduced price from a guy who decided turning wrenches wasn't for him. The thing looks like he never used it. Got it with the snap on ball joint fork that looks unused. I never would have paid full price for it, but that thing is badass . I've been using an old Campbell hausfeld that I bought decades ago. Talk about an upgrade.
I spoke to a few OEMs to figure out how to get different flavors and gathered some local distributors. Shipping time for single orders from Taiwan isn't zippy. I found wacky guns, nine and longer. I found one Aircraft Tool Supply where you can use the sign on coupon with the current sale to have one very generously equipped for 300. I managed a seven inch (like Thor) with a full kit, case, powder coat, feathering trigger, and comfort grip. It even comes with a clever solution to the .401 adapter issue that seems to work quite well....
I have the SnapOn also....I use it for collision/suspension work....for me.....it Was worth it. I have had it for 15 years and it's been a workhorse for sure!!$
Right now I'm running Chicago Pneumatic's 717(the hammer Big Nasty is based off). It has incredible power and a trigger that's easy to baby when you're working on more delicate stuff. In regards to the less common .498 shank size, there are adapters out there that will reduce it to .401.
I freakin' LOVE my Matco hammer. That thing beats HARD. Got it like $40 off retail WITH a four piece flat hammer set. Yes, there is definitely a use for a 12" round head flat hammer. Several so far. This is just one of those tools, we need it often in the salt belt, but still... Kinda like semi deep sockets. You may not need it every day, but when you need it, YOU NEED IT!
You can get an "adapter" to use .401 bits in .498 guns. It is essentially a "sleeve" to allow the use of the smaller bits. They tend to not last very long, because you're talking about a piece of metal that's about 0.097" (the difference between the two sizes) that has to take the extra beating (joules) that a .498 hammer puts out, but if you get a better brand, they'll last you a few times at least. It would allow you to use those specialized .401 bits when you need the extra oomph of the .498 gun.
Heat up the adapter till it is glowing with your torches, let it cool for an hour, heat it up again let it cool some and put it in some used motor oil, it gets hardened and will last longer. I have 3 air hammers, one of them is still a $20 small one for little screws etc... when finesse is needed.
Great video i got IR short barrel been amazed with it , long barrel be my next IR can bring myself to pay for Snap on. In my opinion u can't beat IR in impacts and air hammers for the price 😉
I have the red Snap On heavy hitter. It has even busted semi truck king pins loose for me. My other air hammer is a Blue Point 2050. I use it every day for about 4 years so far
Im a mechanic in a concrete plant and my supervisor purchased me that IR air hammer a few months ago. It worked amazing but the only issue was the set screws on the end backing out. It was used for sometimes up to an hour at a time and even after locktite they still wanted to back out, have to snug them up before every use.
Last air hammer I bought was a Sunex SX243, looks almost exactly like the old Blue Point it replaced. With a 3/4" bore, 3 3 /4" stroke, and 2,200 bpm it has good power for less than $80.
Monte Stu For what it costs I was really impressed that it works decently for light duty tasks, though... cuts sheet metal and spot welds just fine. Good bits are essential no matter what air hammer you choose, of course.
RustyJeep - It has decent power IMO. I’ve only used it a few times, but it got the job done! I didn’t know about the quick release chuck, but I see HF sells them for $5. I’ll pick one up next time.
As much as I’d love to have a Big Nasty of my own, having to buy all new bits holds me back. So, I bought Big Nasty’s little sister, the AP 4901. It’s a super duty hammer that still takes the .401 tools and it’s pretty bad-assed. Plus, it was only about $200.
It would be fun to have the big boy. Then I'd need a new compressor to deliver more cfm. Then I'd need a new set of bits with the larger shank. Then I'd need the quick change adapter -- hope you show us a comparison of that quick change adapter with the spring. One day, ha ha.
I have a Florida Pneumatic 660A (CP717 copy) .498 shank "big nasty" Snap On PH2050 .401 shank And a cheap little Kobalt short stroke air hammer. There's no perfect one does all. Sometimes you just need to lightly vibrate something and ask it to move, and sometimes, you're not asking, it's going to move or else LOL. Grey Pneumatic has a good selection of. 498 shank bits for a good price, and they do have a long shank chisel bit. I have two of them and cut the chisel end off one so I have a long shank blunt end too. If you haven't found them yet, I can get the part number off mine for you.
I wonder how “big nasty” compares to the CP717. My Mac guy years ago was able to come up with a long .498 shank bit that I still have and use. My CP 717 has been an absolute animal and after 13 years of use still works the great. I don’t use the quick chuck adapter on the CP 717, just doesn’t seem safe on such a powerful tool. Not to mention those hardened balls beat up the retainers on the bits.
Great video. Thanks for the information on the bits. I bought a Cornwell years ago and it works fine. In the Southwest we don’t have the rust to worry about. Thanks again.
Long barrel Sunnex , quick release and a half inch connector for the 1 inch tire gun hose or it starves for air . Hardest hitting air hammer I've used in almost 40 years .
Check out Ajax bits for a greater selection of .498" bits. I bought mine in .401" from Air Tools For Less. Have held up great on my PH3050B. Others on garagejournal like them as well, including on larger industrial riveting guns with double the energy of the 4980.
Great video. The Chief CH401 LB is great for the money. Does the job for about 120.00 bucks. I use it at my used car lot. It will keep up with the others.
Seems obvious that 2 are better than one. Lighter duty one for 99% of auto work and something like Big Nasty or Thor for those 1 percenter jobs. I'm probably going to go with the IR119 for starters. I'm a bit concerned about the reported quality issues but they seem common for almost all brands.
I'm on 5 years now with my IR hammer, hope it lasts another 5! Have borrowed my bosses Snap On one like yours one time for a Fan Clutch that just WOULD NOT give and it got it, idk if it was the continued use from both guns or that his was stronger but I got it eventually. Been really happy with it so far. Thanks for your tool reviews, I now have the Milwaukee ratchets at work and use them every day after seeing you talk them up so much and they save me so much time!
Great video thanks brother. Like the comparison between the air hammers. I just got the Ingersoll rand quick chuck with it. I got some longer bits for it also. Thanks to ozstar channel I think I spelled it right. I just followed his link and bam got one. I have a video of when I got it. I have used the cheap ones for years and I can't believe the difference. 401 shank and it kicks butt and don't care. Pretty bad when you retire and upgrade tools. Keep up the great work see you in the next video thanks again brother
The day someone comes out with a battery powered hammer that hits like the IR gun will be a national holiday. That and a small die grinder that can go all day on a charge. 20 years from now folks won't believe how noisy shops used to be.
Best air hammer I ever used was when I worked in the field in 1978-181, it was kind of dimpled texture, they were unbranded, used to be our shop air chisels at Sears. Anyone remember those and who made them?
Everyone should have an air hammer even if its a $10 promo. weld a bolt on one of the punches that comes with it. Use it to beat the mud off the frame and floor pan before crawling under. Be careful on floor pan if the airbag module is there you CAN set off the airbags
I have that Ingersoll Rand long barrel air hammer it's adequate ...it's as good has just about any Quick Connect long barrel air hammer on the market but I do like it... I paid about $120 for the whole kit with the case so that was a pretty decent deal..
Big nasty is a beast I just got it a few months ago. I would be nice if there were more attachments for it. I still use the snap on more because of it. It’s the older all silver one not sure if it’s the same as the newer ones. Had it for about 10 years no problems at all with it.
114GQC Ingersoll Rand. I have had mine around 10 years and still hitting strong. Definitely the best bang for the buck. $43 on Amazon and it comes with a quick chuck and 3 chisels. Very good deal for beginning techs.
I have worked in the past doing front end work and the best gun that I have used was the Chicago pnumatic cp714 and I do have snap on and Mac and ingresol but the hardest hitting gun that I have used has been the CP 714 on numerous occasions I have driven out frozen king pin and Ball joints when the other guns would not be able to budge them I have never regretted getting it it has A lot of use but it is the hardest hitting gun in my arsenal of air hammers!! I am not a sales man just A big fan!!
Weird, I've only oiled mine several times and its lasted 5 years now with lots of use. Guess its hit or miss cus someone else mentioned a problem with theirs as well.
Just make your own ? I’ve made my own long chisel bit . I’d cut the the . 498 and weld on the the .401 . Desperate times calls for desperate measures lol wear safety gears!!
Good video as always bud, I’ve got the blue point in a short barrel version. It works for me it’s always got the job done never actually needed something with more power yet ... the snap on is very expensive here in Australia probably cost 50% more here than in the US and I also don’t think we can get a big nasty from a local supplier either, hopefully once the larger shank becomes more popular and more units are sold they will start making more tooling for them.
I myself own a big nasty and indeed it's a beast. Does not have no feather trigger its just straight balls to the walls once you squeeze. Must have a good grip and no wimpy arms
I had an IR like that, worked well right up until it shot the whole barrel out of the body one day. Bought a Snap-On that afternoon and I've had no issues with it.
Yea that ir sucks had one for a year or 2 prolly no lie 6 rebuilds later my tool guy took it and threw it in the trash gave me my money back and I got the newer style mac one and things badass but can't sleep on the snap on either both hit very hard as I have both
Astro makes a version of Big Nasty with a .401 shank (4901). It doesn't seem to get much attention, but it could be a good solution for someone who doesn't want two hammers.
I’m with you on this one the $500 dollar price tag on the snap on and it’s ok for suspension work on big rigs the .498 air hammer just shits on it and it’s a little cheaper too
Old video I know but after buying Big Nasty's big brother (Astro 498K) I'm in the big shank club now. Have you ever used the adapters to allow the big shank hammers to use the smaller aka "standard" shank bits?
In my case, I could afford to buy off the truck, but its pretty clear that what I would be paying for would not be a good value FOR ME (this is not to say it is not important to someone else). As a non-pro, I don't need the convenience of someone coming to me, nor do I need to buy the tools on time. And sending something back on warranty (which happens once in a blue moon) is not a big deal for me.
Can you use the ingersoll air hammer to clean industrial kitchen stove top with black on it ? Can it be used than having to use a manual scraper which takes plenty time?
If you can find a Snap-On 3050B air hammer used for under $200 that’s a steal. Buy it and thanks me later. No need to buy it new unless you’re getting it for $350 or less.
I bought big nasty. Didn't like it. Like said limited on bits and I don't like the trigger on it, all or nothing. Traded it in on a snap-on so much better. Big nasty is definitely a hard hitting gun but the trigger needs to be improved.
Need a ball joint out? Big Nasty. Brake rotor stuck on hub? Big Nasty. Need to add a few degrees of camber? Big Nasty. Need to remove a blown fuse? Big Nasty. Change the radio station? Big Nasty. Anniversary gift for the wife? Big Nasty.
I'm telling you, it DOES do it all :P
🤣🤣🤣🤣
Big Nasty would be A LOT... LOT more useable if only it had a better trigger.
A nice feather trigger would make it the only air hammer you'd need. But when I'm doing an alignment on a Ford or Dodge truck and I'm trying to remove a Camber/Caster bushing I DO NOT always need or want full throttle balls out power of Big Nasty. Same goes for when I need to finesse a bushing out or just start to chisel something out nice and easy at first.
I think I'm gonna have to get the high-flow air fittings for my Snappy air gun.
AstroTools If your wife needs a Big Nasty you might need to come home early from work unannounced... just saying.
haha I laughed so hard at this...
🤭
The new Astro 401k is gonna turn the entire air hammer market. Hits practically as hard as the snapon at a 5th of the price
Just a heads up you can get a reducer to use a .401 tools in a .498 gun from aircraft tool supply. We use them in the aviation industry all the time.
I love my snap-on 3050B. Takes the wear and tear off of my elbows and shoulders.
I have a Chicago Pneumatic CP715 that I bought new in the early 80's from Sears (I own mostly CP and IR air tools). The CP715 is still in great shape. I run it with the automotive-type high flow air fittings (as I do all my air tools) but I'm going to upgrade it with a quick release chuck and finally dump the spring. Not a tool that I use all that often as a non-pro, but when you need it, that long stroke hammer is gold. I have been finding myself using it more and more though.
One thing to keep in mind with the big, long stroke .498 air hammers (like Big Nasty) is that they are really air hungry. I'm talking like 13cfm@90psi hungry. Yeah, that is the actual running, balls to the wall air consumption of the CP717 (and likely the AP 4980, since it is basically a copy of the CP717). Don't be fooled by the low average air consumption numbers you might see elsewhere, that is kinda like EPA highway mileage. You need like 3x that airflow to really get the full potential out of this tool, as well as at least a 3/8" air line and high flow coupler and fittings. Will it "work" on less? Yes, but not at the performance levels for which it was designed. Which means you could be disappointed in the results. I was looking at them, and quickly realized that although my ailines and fittings are good, my 60 gallon single stage IR reciprocating compressor cannot provide the airflow this beast wants, even at 100% duty cycle (which it is clearly not designed for). This is probably not going to be an issue for most pros in shops with two-stage monster cast-iron compressors, but may be for most DIYers and mobile pros.
I can't believe there wasn't a "hammer time " thrown in there somewhere , nice job mike .trigger went out on my ir a few years ago it cost me a dime to replace the o rings and it's still going strong
When I got started I bought the $38 Ingersoll from Amazon since there were already 3 Snap On air hammers in the shop and surprisingly enough I haven't had to borrow one of them yet. Ive used that thing every day for the last 2 years on ball joints, roll pins, and cv axles on ATVs and I swear it's only gotten stronger with time. I have also seen it outlast 1 Matco so far. For the money it's probably my favorite tool purchase. If it fails I'll probably get a snap on or a larger IR but I can definitely recommend the 114GQC model for a budget gun. I did however buy certain bits from Ebay made by Mayhew. They make Snap Ons punches as well as a lot of other tool truck tools.
I have a ingersoll air hammer, I think it was 70 or 80 bucks, but the thing is amazing, and the good thing with IR is that you can buy replacement parts for them when they do break. I don't know how I did anything before I got an air hammer.
90% of my air hammer use is for ripping old exhaust apart, so I don't need a monster.
Suprisingly, my cheap Campbell-Housfield (from K Mart!) has lasted 20 years.
Snap-on lasted longest without needing rebuild and is more powerful than most. Worth it owned outlast and hits harder than all in my shop
There is always a guy that use air hammer out of sudden in a quiet shop
I always grab earpro unless it's just a one or two second burst, and holler to let everyone know..,.nobody else does.
Me
We use them whenever we are sitting around and the bosses walk through makes it sound like wow those guys are working hard lmao 😂
Quiet shop sounds like an oxymoron
I've used a monster 30 year old Chicago Pneumatic that is about 2 foot long. Insanely powerful still. It will cut car frames in half with 3/4 trigger pull. But will exhaust you in about 1 minute of usage.
Thanks for the video. I was literally just looking at airhammers on the truck the other day. This will help make my decision.
I got the snap on. I love it. Air hammers save your day. I just had to knock off 2 wheel locks.
Yea, the Snappy has a feather trigger that allows you to just get it started and not fly off and damage the wheel.
Thanks Michael. My long barrel Cornwell has served me well. I have an old Sunnex short barrel for tight locations.
This makes me feel better. New-ish Tech in the industry and I went with the IR for my first air hammer purchase. Great video!
I bought the snap on ph 3050 b. I got it at a very reduced price from a guy who decided turning wrenches wasn't for him. The thing looks like he never used it. Got it with the snap on ball joint fork that looks unused. I never would have paid full price for it, but that thing is badass . I've been using an old Campbell hausfeld that I bought decades ago. Talk about an upgrade.
bought the snap on. love it. well worth the money in my opinion.
I spoke to a few OEMs to figure out how to get different flavors and gathered some local distributors. Shipping time for single orders from Taiwan isn't zippy. I found wacky guns, nine and longer. I found one Aircraft Tool Supply where you can use the sign on coupon with the current sale to have one very generously equipped for 300. I managed a seven inch (like Thor) with a full kit, case, powder coat, feathering trigger, and comfort grip. It even comes with a clever solution to the .401 adapter issue that seems to work quite well....
Есть ссылка
I have the SnapOn also....I use it for collision/suspension work....for me.....it Was worth it. I have had it for 15 years and it's been a workhorse for sure!!$
This, Collision wise(im a body tech) everybody ik stands behind snap on making the best air hammer for auto body
Right now I'm running Chicago Pneumatic's 717(the hammer Big Nasty is based off). It has incredible power and a trigger that's easy to baby when you're working on more delicate stuff. In regards to the less common .498 shank size, there are adapters out there that will reduce it to .401.
But those adapters will explode and turn into an emergency room visit
@@Willyd2758 их немного надо переделать и они вечные
I freakin' LOVE my Matco hammer. That thing beats HARD. Got it like $40 off retail WITH a four piece flat hammer set. Yes, there is definitely a use for a 12" round head flat hammer. Several so far. This is just one of those tools, we need it often in the salt belt, but still... Kinda like semi deep sockets. You may not need it every day, but when you need it, YOU NEED IT!
You can get an "adapter" to use .401 bits in .498 guns. It is essentially a "sleeve" to allow the use of the smaller bits. They tend to not last very long, because you're talking about a piece of metal that's about 0.097" (the difference between the two sizes) that has to take the extra beating (joules) that a .498 hammer puts out, but if you get a better brand, they'll last you a few times at least. It would allow you to use those specialized .401 bits when you need the extra oomph of the .498 gun.
Heat up the adapter till it is glowing with your torches, let it cool for an hour, heat it up again let it cool some and put it in some used motor oil, it gets hardened and will last longer. I have 3 air hammers, one of them is still a $20 small one for little screws etc... when finesse is needed.
Патрон 0.498 держит биты 0.401.переход надо не так переделать, И он вечный будет
@@bwdz75 нет, его надо выточить немного не так, и он вечный
Great video i got IR short barrel been amazed with it , long barrel be my next IR can bring myself to pay for Snap on. In my opinion u can't beat IR in impacts and air hammers for the price 😉
I have the red Snap On heavy hitter. It has even busted semi truck king pins loose for me. My other air hammer is a Blue Point 2050. I use it every day for about 4 years so far
Im a mechanic in a concrete plant and my supervisor purchased me that IR air hammer a few months ago. It worked amazing but the only issue was the set screws on the end backing out. It was used for sometimes up to an hour at a time and even after locktite they still wanted to back out, have to snug them up before every use.
Interesting, I've had that IR for 5 years and have never had a problem with it yet and use it pretty often. Been very happy
So true about stuck CV axle shafts. Big Nasty eventually got it free for me but it took me over an hour with the short attachments that I had.
Last air hammer I bought was a Sunex SX243, looks almost exactly like the old Blue Point it replaced. With a 3/4" bore, 3 3 /4" stroke, and 2,200 bpm it has good power for less than $80.
I’m shocked that my $10 Central Pneumatic air hammer didn’t make the list.
Monte Stu For what it costs I was really impressed that it works decently for light duty tasks, though... cuts sheet metal and spot welds just fine. Good bits are essential no matter what air hammer you choose, of course.
Because you were able to pay for it the day you bought it. All the others is like owning a time share.
RustyJeep - It has decent power IMO. I’ve only used it a few times, but it got the job done! I didn’t know about the quick release chuck, but I see HF sells them for $5. I’ll pick one up next time.
As much as I’d love to have a Big Nasty of my own, having to buy all new bits holds me back. So, I bought Big Nasty’s little sister, the AP 4901. It’s a super duty hammer that still takes the .401 tools and it’s pretty bad-assed. Plus, it was only about $200.
Discontinued by the manufacturer.
Well that’s disappointing. Guess I got mine just in time. 😎
It would be fun to have the big boy. Then I'd need a new compressor to deliver more cfm. Then I'd need a new set of bits with the larger shank. Then I'd need the quick change adapter -- hope you show us a comparison of that quick change adapter with the spring. One day, ha ha.
I have a Florida Pneumatic 660A (CP717 copy) .498 shank "big nasty"
Snap On PH2050 .401 shank
And a cheap little Kobalt short stroke air hammer.
There's no perfect one does all. Sometimes you just need to lightly vibrate something and ask it to move, and sometimes, you're not asking, it's going to move or else LOL.
Grey Pneumatic has a good selection of. 498 shank bits for a good price, and they do have a long shank chisel bit. I have two of them and cut the chisel end off one so I have a long shank blunt end too. If you haven't found them yet, I can get the part number off mine for you.
I love how so many people are calling it big nasty now all across youtube
Hunter Skinner, we have the Chicago Pneumatic 717 version of Big Nasty. We call it Beast Mode. And it is.
Just bought one the box even says big nasty now
707SonomaComa It costs a beastly amount more that the Big Nasty too.
"me nasty time" - next Friday ice cube hahaaha
I purchased the blue point air hammer I needed to remove a seized driveshaft and that gun hits hard. It does the job for me.
Best bang for buck is the ir. I recently upgraded to the Mac long barrel. That thing is a beast
I wonder how “big nasty” compares to the CP717. My Mac guy years ago was able to come up with a long .498 shank bit that I still have and use. My CP 717 has been an absolute animal and after 13 years of use still works the great. I don’t use the quick chuck adapter on the CP 717, just doesn’t seem safe on such a powerful tool. Not to mention those hardened balls beat up the retainers on the bits.
Great video. Thanks for the information on the bits. I bought a Cornwell years ago and it works fine. In the Southwest we don’t have the rust to worry about. Thanks again.
AJAX sells an 18" length punch and a chisel in the .498s
chisel PART # 960-18
punch PART # 963-18
What cordless tool comes close to this?? A rotary drill?
Look into aircraft rivet guns the control is much better with a “teaseable” trigger , and come in various strengths
Thanks much. Enjoyed it and would like more tool comparisons.
I use the little air hammers with a hammer end to get stuck hydraulic fittings off more than anything.. Doesn't have enough power to destroy them
The Chief has been pretty impressive around here.
Long barrel Sunnex , quick release and a half inch connector for the 1 inch tire gun hose or it starves for air . Hardest hitting air hammer I've used in almost 40 years .
I just bought a Sunex long barrel air hammer on amazon for $71. Works great
Yup same as the blue point in this video
The IR on hits harder I have the sunex and the shop has the ir so I don’t use mine much unless someone else is using the IR
Check out Ajax bits for a greater selection of .498" bits. I bought mine in .401" from Air Tools For Less. Have held up great on my PH3050B. Others on garagejournal like them as well, including on larger industrial riveting guns with double the energy of the 4980.
Great video. The Chief CH401 LB is great for the money. Does the job for about 120.00 bucks. I use it at my used car lot. It will keep up with the others.
Seems obvious that 2 are better than one. Lighter duty one for 99% of auto work and something like Big Nasty or Thor for those 1 percenter jobs. I'm probably going to go with the IR119 for starters. I'm a bit concerned about the reported quality issues but they seem common for almost all brands.
Found a shank reducer from .498 to
.401. Look on amazon
Thanks a lot... found it on ebay uk ... 15£
Now i can go and order the big nasty!
I'm on 5 years now with my IR hammer, hope it lasts another 5! Have borrowed my bosses Snap On one like yours one time for a Fan Clutch that just WOULD NOT give and it got it, idk if it was the continued use from both guns or that his was stronger but I got it eventually. Been really happy with it so far. Thanks for your tool reviews, I now have the Milwaukee ratchets at work and use them every day after seeing you talk them up so much and they save me so much time!
Great video thanks brother. Like the comparison between the air hammers. I just got the Ingersoll rand quick chuck with it. I got some longer bits for it also. Thanks to ozstar channel I think I spelled it right. I just followed his link and bam got one. I have a video of when I got it. I have used the cheap ones for years and I can't believe the difference. 401 shank and it kicks butt and don't care. Pretty bad when you retire and upgrade tools. Keep up the great work see you in the next video thanks again brother
The day someone comes out with a battery powered hammer that hits like the IR gun will be a national holiday. That and a small die grinder that can go all day on a charge. 20 years from now folks won't believe how noisy shops used to be.
BlindBatG34 Milwaukee is coming out with a 90 degree die grinder soon. I think October
Great review! The .498 shank is a deal breaker for us shade trees.
Ingersoll Rand air hammer is really nice. And for 120 vs 3-400 bucks for the snap on you can't really go wrong.
Cool topic. For such a common tool, air hammers don’t seem to get talked about that much.
asm154 I didn’t start using one until recently I was an idiot lol
Best air hammer I ever used was when I worked in the field in 1978-181, it was kind of dimpled texture, they were unbranded, used to be our shop air chisels at Sears. Anyone remember those and who made them?
I have the Cornwell and it does well. I really want that AP gun for pushing out pins and S cams on big trucks and equipment
Everyone should have an air hammer even if its a $10 promo. weld a bolt on one of the punches that comes with it. Use it to beat the mud off the frame and floor pan before crawling under. Be careful on floor pan if the airbag module is there you CAN set off the airbags
I have that Ingersoll Rand long barrel air hammer it's adequate ...it's as good has just about any Quick Connect long barrel air hammer on the market but I do like it... I paid about $120 for the whole kit with the case so that was a pretty decent deal..
Have you ever used it to remove and install ball joints? I really can't afford big nasty. Thanks
Big nasty is a beast I just got it a few months ago. I would be nice if there were more attachments for it. I still use the snap on more because of it. It’s the older all silver one not sure if it’s the same as the newer ones. Had it for about 10 years no problems at all with it.
They have adapters that let you use 401 bits in 498 guns
114GQC Ingersoll Rand. I have had mine around 10 years and still hitting strong. Definitely the best bang for the buck. $43 on Amazon and it comes with a quick chuck and 3 chisels. Very good deal for beginning techs.
I have worked in the past doing front end work and the best gun that I have used was the Chicago pnumatic cp714 and I do have snap on and Mac and ingresol but the hardest hitting gun that I have used has been the CP 714 on numerous occasions I have driven out frozen king pin and Ball joints when the other guns would not be able to budge them I have never regretted getting it it has A lot of use but it is the hardest hitting gun in my arsenal of air hammers!! I am not a sales man just A big fan!!
I had an IR long barrel, oiled it per their direction.... Lasted 3 weeks
Weird, I've only oiled mine several times and its lasted 5 years now with lots of use. Guess its hit or miss cus someone else mentioned a problem with theirs as well.
Just make your own ? I’ve made my own long chisel bit . I’d cut the the . 498 and weld on the the .401 . Desperate times calls for desperate measures lol wear safety gears!!
I love my Mac air hammer it hits very hard. I don't use daily but several times a week
Good video as always bud, I’ve got the blue point in a short barrel version. It works for me it’s always got the job done never actually needed something with more power yet ... the snap on is very expensive here in Australia probably cost 50% more here than in the US and I also don’t think we can get a big nasty from a local supplier either, hopefully once the larger shank becomes more popular and more units are sold they will start making more tooling for them.
I myself own a big nasty and indeed it's a beast. Does not have no feather trigger its just straight balls to the walls once you squeeze. Must have a good grip and no wimpy arms
I have that ingersall one, it’s awesome
I want buy one soon
Ajax Tools has a good selection of .498 accessories
Lot of guys like the Mac air hammer at our shop, seems to be pretty strong
I have the Snap On. No complaints. Does what I need it to.
I have the Snap on and it has served me well. Think I'll hang on to it . It's paid for 😋
I had an IR like that, worked well right up until it shot the whole barrel out of the body one day. Bought a Snap-On that afternoon and I've had no issues with it.
Yea that ir sucks had one for a year or 2 prolly no lie 6 rebuilds later my tool guy took it and threw it in the trash gave me my money back and I got the newer style mac one and things badass but can't sleep on the snap on either both hit very hard as I have both
Astro makes a version of Big Nasty with a .401 shank (4901). It doesn't seem to get much attention, but it could be a good solution for someone who doesn't want two hammers.
I like you. You seem like a good dude a good boss and this was a good video. Just subscribed.
You should try a Jet 409132 it even better.
Cp717 is my choice for body work.
I’m with you on this one the $500 dollar price tag on the snap on and it’s ok for suspension work on big rigs the .498 air hammer just shits on it and it’s a little cheaper too
You can get an adapter for 498 to 401.
here in Illinois, rust belt I got one (big nasty) love it. and yor are right tools are limited. And she needs a lot of air.
Old video I know but after buying Big Nasty's big brother (Astro 498K) I'm in the big shank club now. Have you ever used the adapters to allow the big shank hammers to use the smaller aka "standard" shank bits?
Thinking about buying a sunex ive eyeballed for a while. Got a husky short for now but it gets me through on some jobs.
The Sunex is solid. Been using mine for a year, power is very close to Snap on and no issues
Check out Honsa air hammers they are an industrial air hammer company from the midwest.
personally im gonna get both sizes, i have a 10$ .401, its good for small stuff but lacks the power
Aaa, us shade-tree mechanics are toooo poor to have tool-truck folks come around. nice hammer info. thanks. :)
In my case, I could afford to buy off the truck, but its pretty clear that what I would be paying for would not be a good value FOR ME (this is not to say it is not important to someone else). As a non-pro, I don't need the convenience of someone coming to me, nor do I need to buy the tools on time. And sending something back on warranty (which happens once in a blue moon) is not a big deal for me.
Can you use the ingersoll air hammer to clean industrial kitchen stove top with black on it ? Can it be used than having to use a manual scraper which takes plenty time?
Hmmm length matters... who knew!!??
lmfao!!
If you can find a Snap-On 3050B air hammer used for under $200 that’s a steal. Buy it and thanks me later. No need to buy it new unless you’re getting it for $350 or less.
Sure Mike, now you tell me I need a big barrel.
What if your in the heavy truck world?
A Guy in my shop has a Blue Point Air Hammer, within our walls it's the bees knees
Get the snap-on, it's worth the money.
Aircat makes a .498 hammer now
BIG NASTY HAS ITS OWN THEME MUSIC😂
Chicago Pneumatic cp715 zip gun is a beast for $60 ish. Look for lower bpm longer stroke.
Could you use it for sinking 18 gauge metal question mark into a bowl shape? I'm having trouble finding an air hammer strong enough
Yup, I still have mine in great shape, bought it new from Sears in the early 80s. Has served me well
This is definitely your funniest video by far. I own both too.
They make a adapter .098 to .401
Witch hits harder the Snap-on or the newer matco
Great video!! Been wanting to buy an air hammer. And yes there’s way too many options out there. You definitely shed some light on the topic.
I needed to used a air hammer on tire for tire patch
Great info , so I'm looking to bash in the bottom of my fire wall on my civic. Witch one would be good for that. Anyone?
I bought big nasty. Didn't like it. Like said limited on bits and I don't like the trigger on it, all or nothing. Traded it in on a snap-on so much better. Big nasty is definitely a hard hitting gun but the trigger needs to be improved.