I agree with you completely, My local stores have also lost their sense of customer service and knowledgeable counter people. They know nothing about cars, and only know what their computer prompts them to ask...I can get that from my own computer and never have to leave the house.
+yourbeekeeper Well I'm having trouble with my heat distribution. The heat blows hot through the defrost outlets and the dash outlets but not so much through the feet outlets. Thinking it might be the little knobs on the dash. Watcha think?
Well.... these Toyotas have cable driven doors. I get strong air flow through my foot vents. It's possible a duct has become dislocated to your lower vents...maybe an aftermarket stereo installation has knocked the ductwork loose? In an '89 toyota pickup I had, the mice would get into the ducts and clog them up with all the debris they made their nests with...that was a complete pain in the neck to get it cleared out...it required removal of the glove compartment and dash control. You should be able to look up under the dash from the passenger side and see where the cables attach to the duct doors. have someone operate the mixer knob and verify the door is fully swinging. Also you can run the fan at full speed while set on the foot position and feel around the ducting under the dash for air leaks.
I love how he shows us with VIDEO where he shops, but the AI isn't smart enough yet to catch what he's showing. It is smart enough to recognize what he's talking about!
Hey Ray, That online place has never let me down in the five or six years I have ben buying from them. If the prices were close, I would have bought it from the store, but this was miles apart by comparison. Thanks for watching My Friend, I appreciate it!
I'm not all that familiar with Toyotas; I own GM vehicles. Toyotas are usually so reliable that I don't have to work on them very often! But I'm having trouble with my Grandpa's old truck and I truly appreciate you walking us through a code-read and fix. Thank you very much for this excellent video! I do wish you sounded those Cadillac horns for us though.
yipeee! you got that check engine light out! It's one of those instructions on Toyota manual and I can still recall performing what you just shared here. Nowadays OBD scanners come in various types and even wireless. But this old stuff is the one I missed because they are cheap compared to what are sold these days. Thanks for sharing and keep up the good work!
Your truck is new enough to be obd2 and the still don't they narrow down which sensor is bad, so if you throw an o2 sensor code, you have to replace all four...That stinks. I have used this parts place for five or six years and have been a very good company to deal with. Thanks for watching!
Thanks alot for posting it really worked. I noticed my temperature gauge stopped working on my 1995 Toyota Corolla and suspected it was the sensor that had gone bad and i watched your video and it confirmed my suspicions when i checked it for myself. I replaced the sensor and now my car dash board is back to normal.
You can buy a Pigtail that connects OBD 1 to OBD 2 so you can use a Scan tool. eBay, $20. If use a Paperclip, try find the Coated ones, peel off coating on ends, so won't short out if touch something. Precaution 😀
really enjoyed watching this video, very informative and with your sense of humor I was able to watch without falling asleep... too bad I don't have a Toyota, I have a Pontiac Aztek and both service vehicle soon and service engine lights up. ugh....
+Yessie Villanueva Thanks Yessie, if that Aztek is an obd1 you can read the flashing light same as this vehicle, just have to search how which port on the plug to jump. GM keys are available online to get the meaning of the flashes. Svc lights are also reset-able by a key sequence...information also available online. if it's obd11, inexpensive redears are availble at places like Harbor Freight or eBay...both lights can be defined and reset with them.
Those bad sensors had everything messed up. I was very happy it came off as easily as it did...I was prepared with the big guns if I needed it. The bolted flange makes it easier to remove and replace for sure. These sensors thread into that flange, and the flange bolts to the pipe.
My 1987 Nissan Pathfinder had a similar procedure; the ECU was mounted under the passenger's seat, and the code(s) would flash using a set of LEDs on the ECU itself.
Only if the '92 is obd1. if it has has the obd2 series port on it, the paperclip does not work (to be best of my knowledge) but you can buy a handheld scanner on eBay for about $20 (search obd2 scanner). I have worked with this hand held scanner and it works well for the non-professional mechanic.
thanks alot for your video, its really great, ive had trouble with my xj cherokee jeep but now i have fixed it from watching your video so thanks again for your video your sincerely Gavin Wilson Australia
your video was of valuable assistance in trouble shooting my experience with the dreaded 'check engine' (idiot) light. Also found your 'car side manners' to be enjoyable as you 'progressed' along from start to finish. Have subscribed and hope your other videos will also be of assistance as well. Keep On Film'n...
Thank you! I think your '98 has the obd2 (on board diagnostic 2) series port on it. If it does, the paperclip does not work (to be best of my knowledge) but you can buy a handheld scanner on eBay for about $20 (search obd2 scanner). I have worked with this hand held scanner and it works well for the non-professional mechanic.
This is just a great video man! I have a 1998 Tacoma 4X4 2.7L and was wondering how if I ever needed to check my trouble codes how to do it. I’m sure it’s the same way as my 98. I’m totally with you on the “brick and mortar store” especially when I live out in the pacific. Wish I was as historical as you in my videos. Aloha and take care Stay warm
I enjoyed your video. My son has a 1995 Toyota truck with the SR 6 cyl engine. Now I'll see what that pesky yellow light has been telling us. I hope you are still making video's. If I can offer a suggestion, when showing the sensor locations, slowly move in on them so we can better see where they live. Best Regards...
Gotta try this in my grandma's 4runner. She keeps getting intermittent CEL. Cane take a truck into the shop, only to have the CEL not be lit or turn off right before you get there, lol.
The vehicle computer will store the CEL code. Even if the light is off, you can still read the stored code, either with a reader or with the paper clip/light counting method. If you don't have a manual you can google the flash count and find the info. Best of luck with the diagnosis...if we're a betting man, I would bet your code is a bad oxygen sensor.
yourbeekeeper I figured it was sensor related also because it's a 21 year old truck and sensors can go bad. It won't be the cat, it's pretty new after someone stole the other one 4 years ago right off the truck. I did run the codes and got 4 of them; lean fuel mix, rich fuel mix, ignition, and TPS. Pretty much pointing to O2 or ignition system. I didn't know how old those codes were so I reset the codes by removing a fuse, according to manual, and have driven the vehicle around a few days. Now only 1 code is showing for a lean/fuel from the O2 sensor. Gonna give it a few more days of driving to make sure that's the only code really remaining and then proceed with the repair.
I remember the paperclip days lol. I actually have a sun pro code scanner that I got in a box o junk from a yard sale last summer, if you want it. just pay the shipping
Awesome! You are 2nd video I watched on this, you are best. Really like that you gave all info on where to get the book & the parts, although you jump around subjects a bit, you are very entertaining, no waste of time on bull...excellent! all parts of video very instructive. ....Both videos forgot to say "Don't forget to remove the clip" I assume the clip is removed directly after you read the code....? 1 real question: Where do you find info on which slots to put paper clip in the reader?
gcNewd Thanks for watching, Yes, once the code is read you can remove the clip. The service book that I talked about on this video tells where to put the paper clip.
Cool Vid man. Thanks. My CE light always comes on with just the key on but goes out after engine start. Unless of course it was on while running before. I note you had almost no gas in the tank when your started this video but had 3/4 tank after the fix. so, in short this start up after the fix was not the first start up after the fix? See where I'm going with this? OR did you happen to add gas to the tank before your first start up? Oh, and you were so spot on with not even considering breaking apart that exhaust flange. That is one bucket of worms you Do Not want to open.
Hey Rick, This video was shot in two segments... the light determination was one day, and the actual replacement of the sensors was done almost a week later.
I don't have anything newer than obd1, so this hangs on a nail in my garage as a dedicated scan tool.Cars are now more gadget and less transportation, which means less serviceability and shorter life span.I mean really,how much technology do you need in a fricking car.Maybe I'm old,But I still see vehicles as tools to move me around this world and not something to order dinner from.Just saying.Oh yeah, I still have your christmas gift, come hell or high water I will get that in the mail. lol.
I like local brick and mirror also, but most of the time these days online is cheaper. Local stores need to learn to adapt and be more competitive with online stores.
To attempt to save $$ try to clean the sensors w wire brush and either carb cleaner or brake cleaner sensors get dirty but rarely completely fail cleaning works usually and if it doesn't your only out a little time and save money
nice vid , you made me think back in auto class , they told us that getting o2 sensors cheap may and i say may may may , result in faulty repairs because the cheap ones maybe not all ? are not to manufacturers specs , other words they cut corners to make them cheap ... i am just saying this because i was told by pros ok , you all do what you got to do ok . no harm intended just makes you think don't it ? enjoy
I agree, Cheap parts rarely last as long as quality parts..but finding a good deal on quality parts is something completely different. In this video I was comparing apples to apples in regard to the o2 sensors. Bosch is hardly considered a cheap part, but finding the exact part at a significantly lower price is a good deal in my book.
Damn right! I do the obd1's that way all the time. I have a cheapo pocket scanner for the obd2 stuff...man do I miss the days of carburetors and cars without every friggin piece of modern technology known to man shoved in the dash and console...sigh.....
OK by doing the paperclip thing for the gas engine light? What else can you do for all the other sensors that’s going out and fuses and paper clips? Where do you put the paper at for any other sensor that went out
I would have put new nuts on the fittings. but an argument can be made that the truck will be sold or junked by the time the next set of O2 sensors has to be installed.
If I tell you how much I paid out to Repair Shops over the last 39 years (me a Landscaper without mechanical know how) your cost might appear insignificant. I tallied it up and it came to the cost of a 2013 one ton diesel truck (loaded) or a 2013 100HP Skid Steer Loader of any make...life is sad isn't it?
I have an outdated KIA sportage. Am from Guyana South America. Its starting and stopping after bubbling for a few seconds. The code is p1121 and P1115 and seemingly has to do with the electronic unit what does these code refer to Thanks
Hi Hemm, I would first determine exactly why the light is on by reading the code... but with that being said, the majority of CEL coming on are related to the o2 sensor being weak or failed and yes, your gasoline consumption will increase with a failed o2 sensor as the engine computer will typically run the vehicle rich with fuel.
If your combi is OBD1 then yes, you can jump the terminal and read the flashing light. Search which pins to jump for your specific model. You can also test the o2 sensor at the sensor itself. If you have a digital multimeter, you can read the voltage coming out of the o2 sensor when the exhaust system is warmed up and running by taking a reading from the wire coming out of the sensor. An oxygen sensor will typically generate up to about 0.9 volts when the fuel mixture is rich and there is little unburned oxygen in the exhaust. When the mixture is lean, the sensor's output voltage will drop down to about 0.1 volts. When everything is warmed up and at operating temp, you should see a reading that is in the lean range. Your system likely has upstream and downstream sensors (before and after the catalytic converter) so be sure to look up your specific model so you don't miss one. Best of luck with your repair.
Typically CEL codes are stored in the vehicle computer until you either pull the battery or do a sequence that clears the computer of the code. So, if the light is not currently on, you are still able to read what the stored CEL code is.
+Armando Martinez Most, if not all, OBDI vehicles have a hack to read the engine codes without an actual reader...they are all different. This method works with all Toyota OBDI vehicles.
depends on the make of the car..regardless of the model just do your research first you can burn out the computer modules if u don't know what you doing.
Amazing what O2 sensors can do, atleast you don't live in the rust belt where you have to use a torch to heat shit to get it apart. It is the ones that screw into a bung in the exhaust pipe are the one that are the pain in the c*** lol.
Codes only happen when the Check Engine Light (CEL) appears. There are times a CEL will light up and then turn off once the problem stops happening or a sensor comes back into its parameters. The computer will store all CEL codes and they can be read either with a scanner or with the blinking CEL light counting method, even if the light is not lit while the vehicle is in operation. OBD I systems are not advanced in regard to live time diagnostics compared to OBD II vehicles, however there are scan tools that can monitor OBD I systyems in live time. Those are fairly expensive and are typically owned be people who work on cars for a living. It is very possible your rough idle is not causing your OBD I system to show a fault so you will not get the opportunity to read a CEL code.
Assuming you are talking about a toyota, a 12 means your computer is not sensing engine RPM and a 24 is a faulty TPS. Both are sensors that most likely need replacing. Before buying anything, I would find those sensors, remove the wire/plug, clean the connection and plug them back in. Reset the computer by removing the fuse for the computer in the fuse block, or disconnect the battery and try to start it again. If the codes continue, replace the sensors.
Rakib Dawan Honestly I am not aware of OBD1 systems that use three digit codes...and if they did, I don't think they would use a zero on it. It was not uncommon for service techs to insert the SST and read the flashes.
I agree with you completely, My local stores have also lost their sense of customer service and knowledgeable counter people. They know nothing about cars, and only know what their computer prompts them to ask...I can get that from my own computer and never have to leave the house.
You're not the only guy with this vid but you are sure as hell the most entertaining. Thank you and I have subscribed and liked. Show me sompin else.
+St White Glad you enjoyed the video and it was helpful. Thanks for the sub...you wanna se simpin else??? Whatcha have in mind?
+yourbeekeeper Well I'm having trouble with my heat distribution. The heat blows hot through the defrost outlets and the dash outlets but not so much through the feet outlets. Thinking it might be the little knobs on the dash. Watcha think?
Well.... these Toyotas have cable driven doors. I get strong air flow through my foot vents. It's possible a duct has become dislocated to your lower vents...maybe an aftermarket stereo installation has knocked the ductwork loose? In an '89 toyota pickup I had, the mice would get into the ducts and clog them up with all the debris they made their nests with...that was a complete pain in the neck to get it cleared out...it required removal of the glove compartment and dash control. You should be able to look up under the dash from the passenger side and see where the cables attach to the duct doors. have someone operate the mixer knob and verify the door is fully swinging. Also you can run the fan at full speed while set on the foot position and feel around the ducting under the dash for air leaks.
I love how he shows us with VIDEO where he shops, but the AI isn't smart enough yet to catch what he's showing. It is smart enough to recognize what he's talking about!
Hey Ray, That online place has never let me down in the five or six years I have ben buying from them. If the prices were close, I would have bought it from the store, but this was miles apart by comparison. Thanks for watching My Friend, I appreciate it!
I'm not all that familiar with Toyotas; I own GM vehicles. Toyotas are usually so reliable that I don't have to work on them very often! But I'm having trouble with my Grandpa's old truck and I truly appreciate you walking us through a code-read and fix. Thank you very much for this excellent video! I do wish you sounded those Cadillac horns for us though.
I would need to know that year, make and model before I could walk you through a code read.
yipeee! you got that check engine light out! It's one of those instructions on Toyota manual and I can still recall performing what you just shared here. Nowadays OBD scanners come in various types and even wireless. But this old stuff is the one I missed because they are cheap compared to what are sold these days. Thanks for sharing and keep up the good work!
Your truck is new enough to be obd2 and the still don't they narrow down which sensor is bad, so if you throw an o2 sensor code, you have to replace all four...That stinks. I have used this parts place for five or six years and have been a very good company to deal with. Thanks for watching!
Thanks alot for posting it really worked. I noticed my temperature gauge stopped working on my 1995 Toyota Corolla and suspected it was the sensor that had gone bad and i watched your video and it confirmed my suspicions when i checked it for myself. I replaced the sensor and now my car dash board is back to normal.
Good job mate. I will do this on my 1992 Toyota Century
You can buy a Pigtail that connects OBD 1 to OBD 2 so you can use a Scan tool. eBay, $20. If use a Paperclip, try find the Coated ones, peel off coating on ends, so won't short out if touch something. Precaution 😀
really enjoyed watching this video, very informative and with your sense of humor I was able to watch without falling asleep... too bad I don't have a Toyota, I have a Pontiac Aztek and both service vehicle soon and service engine lights up. ugh....
+Yessie Villanueva Thanks Yessie, if that Aztek is an obd1 you can read the flashing light same as this vehicle, just have to search how which port on the plug to jump. GM keys are available online to get the meaning of the flashes. Svc lights are also reset-able by a key sequence...information also available online. if it's obd11, inexpensive redears are availble at places like Harbor Freight or eBay...both lights can be defined and reset with them.
I really enjoyed looking at your picture
Those bad sensors had everything messed up. I was very happy it came off as easily as it did...I was prepared with the big guns if I needed it. The bolted flange makes it easier to remove and replace for sure. These sensors thread into that flange, and the flange bolts to the pipe.
My 1987 Nissan Pathfinder had a similar procedure; the ECU was mounted under the passenger's seat, and the code(s) would flash using a set of LEDs on the ECU itself.
I like the OBD1 systems... most all of them had the option to read without a reader... money saver for the typical car owner.
What a small world. I live like 3 blocks from that library! Not really important or life changing, just thought I should share.
Only if the '92 is obd1. if it has has the obd2 series port on it, the paperclip does not work (to be best of my knowledge) but you can buy a handheld scanner on eBay for about $20 (search obd2 scanner). I have worked with this hand held scanner and it works well for the non-professional mechanic.
thanks alot for your video, its really great, ive had trouble with my xj cherokee jeep but now i have fixed it from watching your video so thanks again for your video your sincerely Gavin Wilson Australia
+Gavin Wilson That's great Gavin, Glad I could help out.
Hey, Thanks for the offer, but everything I drive is obd1 and I have the service manuals for all my rigs..so reading codes is easy. I appreciate that!
your video was of valuable assistance in trouble shooting my experience with the dreaded 'check engine' (idiot) light. Also found your 'car side manners' to be enjoyable as you 'progressed' along from start to finish. Have subscribed and hope your other videos will also be of assistance as well. Keep On Film'n...
Thanks Raymond.
Thank you! I think your '98 has the obd2 (on board diagnostic 2) series port on it. If it does, the paperclip does not work (to be best of my knowledge) but you can buy a handheld scanner on eBay for about $20 (search obd2 scanner). I have worked with this hand held scanner and it works well for the non-professional mechanic.
your instructions were clear ..concise and easy to follow.. phenamenol (jamaica)
Thank you, I am glad I was able to help you out. Thanks for watching.
This is just a great video man! I have a 1998 Tacoma 4X4 2.7L and was wondering how if I ever needed to check my trouble codes how to do it. I’m sure it’s the same way as my 98. I’m totally with you on the “brick and mortar store” especially when I live out in the pacific. Wish I was as historical as you in my videos.
Aloha and take care
Stay warm
You have a good sense of humor thanks for the info!
+Sherry Muss. You are very welcome. Glad I could help out.
I enjoyed your video. My son has a 1995 Toyota truck with the SR 6 cyl engine. Now I'll see what that pesky yellow light has been telling us. I hope you are still making video's. If I can offer a suggestion, when showing the sensor locations, slowly move in on them so we can better see where they live. Best Regards...
Thanks Michael
They are way better than the anemic stock horns. People pay attention to these. Thanks for watching.
Gotta try this in my grandma's 4runner. She keeps getting intermittent CEL. Cane take a truck into the shop, only to have the CEL not be lit or turn off right before you get there, lol.
The vehicle computer will store the CEL code. Even if the light is off, you can still read the stored code, either with a reader or with the paper clip/light counting method. If you don't have a manual you can google the flash count and find the info. Best of luck with the diagnosis...if we're a betting man, I would bet your code is a bad oxygen sensor.
yourbeekeeper I figured it was sensor related also because it's a 21 year old truck and sensors can go bad. It won't be the cat, it's pretty new after someone stole the other one 4 years ago right off the truck. I did run the codes and got 4 of them; lean fuel mix, rich fuel mix, ignition, and TPS. Pretty much pointing to O2 or ignition system. I didn't know how old those codes were so I reset the codes by removing a fuse, according to manual, and have driven the vehicle around a few days. Now only 1 code is showing for a lean/fuel from the O2 sensor. Gonna give it a few more days of driving to make sure that's the only code really remaining and then proceed with the repair.
That's real money to save! Thanks for watching.
oh man, I agree with you completely again... the auto correct is a pain in the neck!
I remember the paperclip days lol. I actually have a sun pro code scanner that I got in a box o junk from a yard sale last summer, if you want it. just pay the shipping
Anytime...thanks for watching.
Awesome! You are 2nd video I watched on this, you are best. Really like that you gave all info on where to get the book & the parts, although you jump around subjects a bit, you are very entertaining, no waste of time on bull...excellent! all parts of video very instructive. ....Both videos forgot to say "Don't forget to remove the clip" I assume the clip is removed directly after you read the code....?
1 real question: Where do you find info on which slots to put paper clip in the reader?
gcNewd Thanks for watching, Yes, once the code is read you can remove the clip. The service book that I talked about on this video tells where to put the paper clip.
Great information, enjoyed the humor😊
Great Job, very informative. I deal with Rock Auto all the time.
+Stephen Neuabuer Thank you. I still have great dealing with Rock Auto...
The speaker identifies with the number for the code but does not tell you what the code is related to.
Cool Vid man. Thanks. My CE light always comes on with just the key on but goes out after engine start. Unless of course it was on while running before. I note you had almost no gas in the tank when your started this video but had 3/4 tank after the fix. so, in short this start up after the fix was not the first start up after the fix? See where I'm going with this? OR did you happen to add gas to the tank before your first start up? Oh, and you were so spot on with not even considering breaking apart that exhaust flange. That is one bucket of worms you Do Not want to open.
Hey Rick, This video was shot in two segments... the light determination was one day, and the actual replacement of the sensors was done almost a week later.
8:02
39 degrees is chilly, hah. Being on the Celsius scale, it is in fact 39 degrees right now, and it's what you would classify as hell.
***** hahaha, Temp is all relative.
+FracturedPixels 39 degrees is t-shirt weather where I live.
I don't have anything newer than obd1, so this hangs on a nail in my garage as a dedicated scan tool.Cars are now more gadget and less transportation, which means less serviceability and shorter life span.I mean really,how much technology do you need in a fricking car.Maybe I'm old,But I still see vehicles as tools to move me around this world and not something to order dinner from.Just saying.Oh yeah, I still have your christmas gift, come hell or high water I will get that in the mail. lol.
The cost of a vehicle goes way beyond the purchase price.
I like local brick and mirror also, but most of the time these days online is cheaper. Local stores need to learn to adapt and be more competitive with online stores.
That sucks! Sorry to hear about that.
You are very welcome. Glad I could help out.
nice video and thanks for the info, i learned something new again today.
+sgtjoe2008 Fantastic. Glad I could help out.
To attempt to save $$ try to clean the sensors w wire brush and either carb cleaner or brake cleaner sensors get dirty but rarely completely fail cleaning works usually and if it doesn't your only out a little time and save money
nice vid , you made me think back in auto class , they told us that getting o2 sensors cheap may and i say may may may , result in faulty repairs because the cheap ones maybe not all ? are not to manufacturers specs , other words they cut corners to make them cheap ... i am just saying this because i was told by pros ok , you all do what you got to do ok . no harm intended just makes you think don't it ? enjoy
I agree, Cheap parts rarely last as long as quality parts..but finding a good deal on quality parts is something completely different. In this video I was comparing apples to apples in regard to the o2 sensors. Bosch is hardly considered a cheap part, but finding the exact part at a significantly lower price is a good deal in my book.
i know and understand ,,,carry on soldier LOL
Thanks bro, Now I can do the same with my '91 toyota/winnebago rv !
Damn right! I do the obd1's that way all the time. I have a cheapo pocket scanner for the obd2 stuff...man do I miss the days of carburetors and cars without every friggin piece of modern technology known to man shoved in the dash and console...sigh.....
OK by doing the paperclip thing for the gas engine light? What else can you do for all the other sensors that’s going out and fuses and paper clips? Where do you put the paper at for any other sensor that went out
Hmmm, 95 Corolla should still be an OBD1 system...it should work... Be very sure you are putting your wire in the correct ports.
Put a train horn on my Pontiac Torrent
Roger that. Will check it out.
Thank you for replying
Aloha
I would have put new nuts on the fittings. but an argument can be made that the truck will be sold or junked by the time the next set of O2 sensors has to be installed.
I did give that some thought... but these have been holding tight so I will leave them alone. Thanks!
Dang, that's cold enough to freeze your gibblets off!
If I tell you how much I paid out to Repair Shops over the last 39 years (me a Landscaper without mechanical know how) your cost might appear insignificant. I tallied it up and it came to the cost of a 2013 one ton diesel truck (loaded) or a 2013 100HP Skid Steer Loader of any make...life is sad isn't it?
awesome! I have liked and subscribe thank you
Mine only flashes the check engine
I have a 94 Chevrolet Camaro LT1, I have tried reading the computer with an OBD1 and it doesn't recognize the car,what do I need to do?
Reading the computer with a clip like this video or with an actual reader?
I have an outdated KIA sportage. Am from Guyana South America. Its starting and stopping after bubbling for a few seconds. The code is p1121 and P1115 and seemingly has to do with the electronic unit
what does these code refer to Thanks
+Rajendra Bisessar P1121 in a Kia is a bad throttle position sensor and a P1115 is a coolant temp sensor.
Awesome & very witty 🤗🙃👅
Hey @yourbeekeeper there is no T1 TE1 on my 1988 Toyota Corolla fx zi but there is TEM and I was wondering if TEM terminal and TE1 is the same. Cheers
Sorry, I don't know if the are the same.
39 degrees, man that is a heat wave! It gas been in the teens and single digits here for a week! ;}
pretty slick man .
is it the same on a 92 gmc truck ?
Would this work for a 93 pickup?
I have a 95 Toyota Camry and tried it with an aluminum paper clip and a copper wire and couldn't get it to work. Any suggestions?
Thank you.
Hi my engine light is on and I feel it is the oxygen sensor but is is possible when the engine light gets on the fuel use will go up?!!??
Hi Hemm, I would first determine exactly why the light is on by reading the code... but with that being said, the majority of CEL coming on are related to the o2 sensor being weak or failed and yes, your gasoline consumption will increase with a failed o2 sensor as the engine computer will typically run the vehicle rich with fuel.
Thank you so much but is it possible to read the code without special equipment! I have Ford Focus 1999 combi
If your combi is OBD1 then yes, you can jump the terminal and read the flashing light. Search which pins to jump for your specific model. You can also test the o2 sensor at the sensor itself. If you have a digital multimeter, you can read the voltage coming out of the o2 sensor when the exhaust system is warmed up and running by taking a reading from the wire coming out of the sensor. An oxygen sensor will typically generate up to about 0.9 volts when the fuel mixture is rich and there is little unburned oxygen in the exhaust. When the mixture is lean, the sensor's output voltage will drop down to about 0.1 volts. When everything is warmed up and at operating temp, you should see a reading that is in the lean range. Your system likely has upstream and downstream sensors (before and after the catalytic converter) so be sure to look up your specific model so you don't miss one. Best of luck with your repair.
Thank you very much don't now how to appreciate thanks a lot
Hi could you help with my truck 2000 Toyota prado , flashes of check engine light reads 9 9 9
Toyota doesn't show any codes for 99, it is likely a code 9, which is a failed vehicle speed sensor signal.
Good Show- Thanks
+James Crawford You're welcome. Glad to help out.
Would this method still work if the cel only comes on after driving the car? And doesnt pop up when juat sitting idle
Typically CEL codes are stored in the vehicle computer until you either pull the battery or do a sequence that clears the computer of the code. So, if the light is not currently on, you are still able to read what the stored CEL code is.
@@yourbeekeeper awesome thank you so much I'll have to check this! Video from ages ago saving me now man🙏😂
@@mateuszz7 Awesome, Happy to help out... that's what YT should be about.
My check engine doesn’t flash
Can you tell me how to do this with a 2001 Toyota Sequoia?
Your year is an OBDii and I don't know how to scan an OBDii system with out an actual hand held scanner.
My diagnosise port is not working i opend it and i find out that some cables are not attachef
Very Entertaining. Good info too.
Thanks for watching.
What year is your truck I have a 1994 Toyota pick up can I do the same
Mine is a 1994 and it will be exactly the same.
Very cool video, thanks.
Your welcome. Thanks for wathcing.
thanks
It did not work on my 1998 T100, does anyone knows how get the codes without a reader for my T100.
So I can't get the engine up to temp because it won't start. That's why I need the codes in the 1st place. Will it still work?
April Arroyo Yes, this technique reads stored codes. As long as you can get the ignition to turn on you can read the store codes.
yourbeekeeper it's also a 99. Is that to new to do this?
I believe a '99 is OBDII, so yes, it's too new to be best of my knowledge.
That's great! Thank you!
...useful video, i hope my 21error goes to.
Thanks.
Were can i found the book for camry
will it work for a 1995 toyota tacoma?
Only if it is still an OBDI system.
Does that work with any car?
+Armando Martinez Most, if not all, OBDI vehicles have a hack to read the engine codes without an actual reader...they are all different. This method works with all Toyota OBDI vehicles.
depends on the make of the car..regardless of the model just do your research first you can burn out the computer modules if u don't know what you doing.
why does mine not have the second oxygen sensor its some what funny
I'm starting to hate auto complete on my phone
I meant 'mortor'
Amazing what O2 sensors can do, atleast you don't live in the rust belt where you have to use a torch to heat shit to get it apart. It is the ones that screw into a bung in the exhaust pipe are the one that are the pain in the c*** lol.
New friend full support idol
Thank you.
great video entertaining commentary
if there is no check engine light and I am getting a rough idle will the vehicle still show codes ?
Codes only happen when the Check Engine Light (CEL) appears. There are times a CEL will light up and then turn off once the problem stops happening or a sensor comes back into its parameters. The computer will store all CEL codes and they can be read either with a scanner or with the blinking CEL light counting method, even if the light is not lit while the vehicle is in operation. OBD I systems are not advanced in regard to live time diagnostics compared to OBD II vehicles, however there are scan tools that can monitor OBD I systyems in live time. Those are fairly expensive and are typically owned be people who work on cars for a living. It is very possible your rough idle is not causing your OBD I system to show a fault so you will not get the opportunity to read a CEL code.
Or figuring its a toyota
Hey was just watching your paper clip presentation do you have a fix for 11124. Code..Cool if you do.
Hi Gerald, There is no listing for a 11124 code. Maybe it's a 24 code which is a Throttle Position Sensor fault.
yourbeekeeper my bad it was 12 and 24
Assuming you are talking about a toyota, a 12 means your computer is not sensing engine RPM and a 24 is a faulty TPS. Both are sensors that most likely need replacing. Before buying anything, I would find those sensors, remove the wire/plug, clean the connection and plug them back in. Reset the computer by removing the fuse for the computer in the fuse block, or disconnect the battery and try to start it again. If the codes continue, replace the sensors.
its true what his doing is exactly right.
Hey bro Will that work on my 1993 22re
and by the way if I moved my oxi sensor form down under and put it right in the manifold where the four meet will it be ok
Yep, you can read the codes exactly the way I showed. I don't know for sure about the ox. sensor though, but I don't see why it would be an issue.
will this work for my 1988 toyota pickup
Yes.
very nice good job
Thank you! 😊
Cool vid, thanks!
how i can pull 3digit codes?
if you have a three digit code, it will flash in a three sequence pattern..same as I showed but with one extra.
yourbeekeeper can u tell me how to read codes like ex 301or402or101,how many flash for number zero?
Rakib Dawan
Honestly I am not aware of OBD1 systems that use three digit codes...and if they did, I don't think they would use a zero on it. It was not uncommon for service techs to insert the SST and read the flashes.
Won't this paper clip shorten out the fuse or the ECU? So much for being a cheapskate.
no, i have never had any issues with this method.
Lol, good video!
Thank you
sameer punkin
Good vid
TATER TOTS!!!....yummmmmmmmmm
You know that's right.