Hi Adam, did some short trim flights from a small hill yesterday on my rudder elevator glider and used the trim buttons to get thing’s right and today used the sub trim to make things permanent, your video confirmed everything, thanks.
Awesome 👍👍 thank you very much Adam for making this video,and your explaining style is so good.I am new to rc and your videos helped me a lot .Thank you very much and keep it up👍
The fundamental fiference between trims and subtrims is that trims affects channel inputs (values from sticks), while subtrims are applied to putputs (channels values sent to receiver). Thus, trims affect mixers, while subtrims do not. This difference is usually subtle, but in some cases, becomes significant!
I set up some trim whilst flying. Trim not subtrim. When I made the switch for dual rates and expo, it adjusted the trim also. Why is this. This is not good when switching to dual rates. I have the same TX as in the video. Thanks.
If you use the trim in flysky during flight does it save it like that it does it go back after the radio is turned off? How do you know what trim button controls what?
Love this vid! Quick question, does the RX battery level indicate the battery level of my zohd li-ion 3500mah battery or is that something else? Thanks
I'm building a rescue boat for my gas boats in event where I can't get a boat back to shore.Its construction is 3\4 in. PVC,pool noodles for floatation,2 electric motors,2 30 amp esc's, one 4s lipo, controlled by the flysky fsi6 and fsia6b receiver. I watched your video on setting up a two motor set up and put all the values you said to do on that episode but for some reason I cannot get the motors to spin regardless of any settings I try .I bought two new motors thinking of potential reasons for not working.I also replaced the receiver after the guy in the hobby shop noticed that it was very hot. What am I doing wrong please help!!
Another reason for using subtrim is to adjust the servo arms to where you want them with no stick input. For example, if you want the servo arm a 90 deg to the servo body you may need to use trim to do it.
Hi Adam, once you correct with the sub trim is it correct to assume that you regain the same full stick and trim ranges in both directions? Cheers John
Hi Adam.. May I know the receiver you're using with the flysky transmitter.. what about it's real-time range also which fs receiver is best for long range
@@RCwithAdam1 Thank u Adam! My quad recently failsafed out of RXLOSS though I had RSSI of 34% . I'm using Fli14+... also quite not sure about the best placement of receiver antennas for optimum signal strength
My ia10b receiver started disconnecting itself and connecting back after some attempts of turning off and in again. Had problems binding it even when bind plug is plugged in. Is there a problem with the antenna???
Would this be applicable to tracked vehicles ? my dozer servo drives are running slightly out of trim, have to keep jogging the controls to keep it straight....
@Adam, what if you subtrim so that the control surface is straight, but the servo arm is not exactly perpedicular with the control rod? Then you won't have equal throw in both directions. How do you deal with this situation?
How to make the alieron and elevator mix ? For example when I turn left and right with the alieron I want the elavtor to move up aswell . instead when I turn to one side the elevator goes down and when I turn to the other side it goes up . how to make the elevator stay up when I turn both sides?
Trying to use my flysky FS-I6x on a sim on my PC but I am unable to match my channels through the setting on the Sim, is there a way on the flysky FS-I6x to change Channel 1 and 5 to fool the Sim to work as I need it? Thanks in advance.
I am so desperate with my FS-i6X. Bought it right after my FS-T6B broke. In FS-i6X - my throttle is zeroed when the stick is in the middle. So I only have 50% forward thrust and 50% reverse thrust. And it's a plane, so this doesn't work with me. I need all 100% of thrust in a single direction of movement of the stick. Could somebody please help me out with an advice??:(
Oh no! Let's see if we can get you back in the air! Is the throttle spring-loaded to center? If so, this video might help: ua-cam.com/video/5LgzG7aE8IQ/v-deo.html
@@RCwithAdam1 the transmitter is difficult to set up to use arcade style ...1 stick driving.....even though you use the key to lock the settings in.....they still will change I am sure they work well with r/c aircraft and I am still trying to make mine work correctly....
Great explanations all the time, the best RC videos I've seen..Bravo Mr Adam.
Thank you for a very good explanation on how it works. I'm a helicopter guy who enjoys scale flying and this really helps.
Hi Adam, did some short trim flights from a small hill yesterday on my rudder elevator glider and used the trim buttons to get thing’s right and today used the sub trim to make things permanent, your video confirmed everything, thanks.
Great!
Awesome 👍👍 thank you very much Adam for making this video,and your explaining style is so good.I am new to rc and your videos helped me a lot .Thank you very much and keep it up👍
The fundamental fiference between trims and subtrims is that trims affects channel inputs (values from sticks), while subtrims are applied to putputs (channels values sent to receiver).
Thus, trims affect mixers, while subtrims do not. This difference is usually subtle, but in some cases, becomes significant!
Awesome video buddy. I'm new to RC and your videos have helped me alot. Thanks again!
Super! Welcome aboard! Glad I can help!
Very helpful and practical demo. Thank you.
Great video! Is it ideal to trim stationary?
Great explanation! I hope to be getting an i6x shortly and this info helps greatly. Thank you.
Glad it was helpful!
Thanks Adam, very nice video
Great video . I subscribed and liked 👍 ....
How would you adjust the throttle? Jist built the drone and its saying to much throttle is applied even tho the stick is all the way down
I set up some trim whilst flying. Trim not subtrim. When I made the switch for dual rates and expo, it adjusted the trim also. Why is this. This is not good when switching to dual rates. I have the same TX as in the video. Thanks.
If you use the trim in flysky during flight does it save it like that it does it go back after the radio is turned off? How do you know what trim button controls what?
Love this vid! Quick question, does the RX battery level indicate the battery level of my zohd li-ion 3500mah battery or is that something else? Thanks
it is showing you receiver voltage which is provided voltage from esc
I'm building a rescue boat for my gas boats in event where I can't get a boat back to shore.Its construction is 3\4 in. PVC,pool noodles for floatation,2 electric motors,2 30 amp esc's, one 4s lipo, controlled by the flysky fsi6 and fsia6b receiver. I watched your video on setting up a two motor set up and put all the values you said to do on that episode but for some reason I cannot get the motors to spin regardless of any settings I try .I bought two new motors thinking of potential reasons for not working.I also replaced the receiver after the guy in the hobby shop noticed that it was very hot. What am I doing wrong please help!!
Another reason for using subtrim is to adjust the servo arms to where you want them with no stick input. For example, if you want the servo arm a 90 deg to the servo body you may need to use trim to do it.
You had me at the title. 😃😃👍
Hi I have some issues with my rudder. Sometimes it will turn full left but there are times it will only move 1/4.
Sir thanks 👍..
NICE VIDEO SO IN SUBTIM do you lose throw in one direction too the same as trim
Thanks! Yes.
Hi Adam, once you correct with the sub trim is it correct to assume that you regain the same full stick and trim ranges in both directions? Cheers John
Oops, just noticed you already answered this before. And you regain full throws on the stick and the trims.
Thank you for the good explanation. That worked out for me. Also, the number of like is 420 I will leave it there.
Thank you 👍
Hi Adam.. May I know the receiver you're using with the flysky transmitter.. what about it's real-time range also which fs receiver is best for long range
Hi! Usually, for airplanes I use FS-iA6B, and for quads I use XR-602TA, or Fli14+, or FS-X6B. Can't say positively which is best for range.
@@RCwithAdam1 Thank u Adam! My quad recently failsafed out of RXLOSS though I had RSSI of 34% . I'm using Fli14+... also quite not sure about the best placement of receiver antennas for optimum signal strength
Awesome, awesome, Awesome....Thank you!
You're welcome, welcome, welcome!! 😁 thanks for the feedback!
My ia10b receiver started disconnecting itself and connecting back after some attempts of turning off and in again. Had problems binding it even when bind plug is plugged in. Is there a problem with the antenna???
Would this be applicable to tracked vehicles ? my dozer servo drives are running slightly out of trim, have to keep jogging the controls to keep it straight....
I can't say. I've never used a tracked vehicle.
4:12 nice beat trimmer
@Adam, what if you subtrim so that the control surface is straight, but the servo arm is not exactly perpedicular with the control rod? Then you won't have equal throw in both directions. How do you deal with this situation?
Get a linkage stopper.
@@sourjyanaskar6092 thanks
How to make the alieron and elevator mix ? For example when I turn left and right with the alieron I want the elavtor to move up aswell . instead when I turn to one side the elevator goes down and when I turn to the other side it goes up . how to make the elevator stay up when I turn both sides?
Hi! Good question! I haven't tried that yet so I'll have to look into it.
@@RCwithAdam1 I got it . thank
Trying to use my flysky FS-I6x on a sim on my PC but I am unable to match my channels through the setting on the Sim, is there a way on the flysky FS-I6x to change Channel 1 and 5 to fool the Sim to work as I need it? Thanks in advance.
I had the same problem on free drone games. No fix, but drl drone racing league reads my fs i6x perfectly
How i can save the trim??
can we trim the motors speed?
I am so desperate with my FS-i6X. Bought it right after my FS-T6B broke. In FS-i6X - my throttle is zeroed when the stick is in the middle. So I only have 50% forward thrust and 50% reverse thrust. And it's a plane, so this doesn't work with me. I need all 100% of thrust in a single direction of movement of the stick. Could somebody please help me out with an advice??:(
Oh no! Let's see if we can get you back in the air! Is the throttle spring-loaded to center? If so, this video might help: ua-cam.com/video/5LgzG7aE8IQ/v-deo.html
Sir how i set altitude hold usin fsi6 trnasmitter😊
That is not something that is set via the transmitter. For which aircraft?
Hi sir how to start first time fs i6 tranmiter
Super bro
Can u fly and heli with these controllers
You sure can! Though I haven't actually tried it.
@@RCwithAdam1 I couldn't bind it wirh nothing I have a blade cx3 but it dont do anything when i bind it
@@leonjohnsonjr3331 I believe the Blade models require a Spektrum brand transmitter (DSM2 radio protocol).
@@RCwithAdam1 ok that's probably why
Needed
if you are using your transmitter to operate a wheeled vehicle, imho, consider a different brand
Thanks for your input. Why is this?
@@RCwithAdam1 the transmitter is difficult to set up to use arcade style ...1 stick driving.....even though you use the key to lock the settings in.....they still will change I am sure they work well with r/c aircraft and I am still trying to make mine work correctly....
you didn't show how subtrim effects the throw
Good point. I do show that in this newer video, though, for the i6S ua-cam.com/video/5vvNnyT9DpA/v-deo.html