Thanks Dave. I have a Horizon T901 with a bad running belt. I was considering upgrading to the Horizon 7.0, but my desire to save $1000, combined with your video, has given me the motivation and confidence to replace it myself. Already have it 1/2 disassembled and ordering a replacement belt. 👍🤞
@@gregsholly120 Ok sounds good I can help with the belt also may have a better price on that. I know we make them better. If you want send me your full model number to Fitnesspartspro@gmail.com
I have had a horizon 7.0 for over 4 yrs with alot of miles on it that needs drive belt and treadmill belt along with deck,is it worth fixing rather than buying another treadmill ?
@@masterofnone7846 That’s hard to say check the motor warranty just for future information ... walk belts run 180 to 220 depending on what thickness and quality .decks 200 ...so depends on what the new unit cost
Great video, I got the belt on and running, have two left over parts though that I can’t remember where there go, any suggestions on where I can go to figure that out?
Great video, thank you, I replaced the belt perfectly here in the UK. I am having problem tho with the bet slowing down after approx 20 minutes at 6kph, it appears to slow to around 4kph, when I get off its back to its normal 6kph. The belt appears to be fine, what would you suggest I check first?
Well thank you. You will need to amp it check your ac amps with no one on it then with a user on it if it is 3 times higher with a load then check deck for wear . If amps only double or less! Then controller is weaker. See my video on treadmill power meter to get an example
Great video. I replaced the walking belt on my horizon t500 I’ve had since 2008. I’m not sure what I did wrong but if you are at the foot of the treadmill looking up at the control panel the belt immediately shifts to the left and runs into the drive belt after about a minute.
@@FitnessTechnologyServices Thank you!!That fixed it. I spent a lot of my weekend trying to replace this belt with no background in repairing a treadmill and didn’t feel like I had anything to show for it so thank you very much for allowing me to complete this project.
What tool do you use to thread the rear bolts? I removed mine in an attempt to loosen the belt and realign/re center my belt and now i cannot get either bolt to thread back in the hole with the allen wrench that came with the tread mill. Very frustrrating!
But why cut the old belt after seeing only having to lift deck to put on new belt also after removing the back roller completely I thought it would’ve been easier to just slacken the front .like u said when working on the road ,time is everything but still very informative thanks been a great help
Well no good reason really,no one has ever asked me that before 🤔.But it is faster and you can’t reuse it, except for it makes a great grass blocker under stone walkway. And thanks please subscribe Dave
Hi! I can’t see what the static guard strap looks like. I see you unscrew something and place it under the treadmill where I can’t see what it is shaped like. But, I got this far with the video really well!
Would this treadmill be pretty similar to the Horizon CT5.0 layout? I need a new belt so i am hoping that I could follow this when I get my new one. I'm a first timer at changing a belt!
Well both of us would need your model and serial number to see what size . Sometimes are belt is too thick and heavy send information to Fitnesspartspro@ gmail.com
@@tuccan1 There should be a longer model number also. Look on the frame by the power cord also on horizon the serial number is important it is TM and a long set of numbers after
Morning, Glad the video was helpful. I also put a link to my channel. If you have a moment please SUBSCRIBE as it really helps me. Of course I can help you with any of your fitness equipment questions and parts. Well I can make one for you I would need the full serial # and the length and width. I will add a link to measure. Thanks Dave MEASURING TREADMILL WALK BELT ua-cam.com/video/SGo3Vb1apFE/v-deo.html Treadmill walk belt comparison ua-cam.com/video/R-JeRjZQ0io/v-deo.htmlua-cam.com/channels/Eubtuz3EILUAT8KamxKpPQ.htmlvideos
You should have mentioned that the belt should be checked to see if it's directional. You likely know that and may have checked when you got the belt, but anyone doing it for the first time might miss that detail.
Very few belt are directional! This one is not so no need to mention it on a unit that doesn’t require it. Most of the units I work on don’t maybe commercial? I have not seen one in 15 years
Great video, I got the belt on and running, have two left over parts though that I can’t remember where there go, any suggestions on where I can go to figure that out?
Great video, I got the belt on and running, have two left over parts though that I can’t remember where there go, any suggestions on where I can go to figure that out?
Thanks Dave. I have a Horizon T901 with a bad running belt. I was considering upgrading to the Horizon 7.0, but my desire to save $1000, combined with your video, has given me the motivation and confidence to replace it myself. Already have it 1/2 disassembled and ordering a replacement belt. 👍🤞
@@gregsholly120 Ok sounds good I can help with the belt also may have a better price on that. I know we make them better. If you want send me your full model number to Fitnesspartspro@gmail.com
Very timely video. Thank you for posting because this is exactly what I needed.
My pleasure
That’s great video.. I just ordered my replacement belt for my Horizon T102. 👍
Thank you .. just put that one up see my full channel fitness technology services just started Horizon line more to come . Dave
Yes a great and helpful video. Just note that if you have an horizon like mine you will have to take the board right off
What company makes the belt you installed?
Thank you-very detailed! I'm just about done with my belt replacement.
Well you are so welcome! Please subscribe Dave
Thanks for this! Very helpful.
Always my pleasure!
I have had a horizon 7.0 for over 4 yrs with alot of miles on it that needs drive belt and treadmill belt along with deck,is it worth fixing rather than buying another treadmill ?
@@masterofnone7846 That’s hard to say check the motor warranty just for future information ... walk belts run 180 to 220 depending on what thickness and quality .decks 200 ...so depends on what the new unit cost
Great video, I got the belt on and running, have two left over parts though that I can’t remember where there go, any suggestions on where I can go to figure that out?
You will need to send me a picture and I will see if I can help
Great video, thank you, I replaced the belt perfectly here in the UK. I am having problem tho with the bet slowing down after approx 20 minutes at 6kph, it appears to slow to around 4kph, when I get off its back to its normal 6kph. The belt appears to be fine, what would you suggest I check first?
Well thank you. You will need to amp it check your ac amps with no one on it then with a user on it if it is 3 times higher with a load then check deck for wear . If amps only double or less! Then controller is weaker. See my video on treadmill power meter to get an example
Great video. I replaced the walking belt on my horizon t500 I’ve had since 2008. I’m not sure what I did wrong but if you are at the foot of the treadmill looking up at the control panel the belt immediately shifts to the left and runs into the drive belt after about a minute.
Any ideas?
This sounds like the front roller is off center. Try adjusting the front roller slowly towards the rear Let me know.
@@FitnessTechnologyServices Thank you!!That fixed it. I spent a lot of my weekend trying to replace this belt with no background in repairing a treadmill and didn’t feel like I had anything to show for it so thank you very much for allowing me to complete this project.
What tool do you use to thread the rear bolts? I removed mine in an attempt to loosen the belt and realign/re center my belt and now i cannot get either bolt to thread back in the hole with the allen wrench that came with the tread mill. Very frustrrating!
Just the Allen wrench
My girlfriend has this treadmill and the belt keeps slipping to the right. Do you know how i can fix this
I have a video on this under adjusting sole walk belt. But go to the side that the belt is moving to and tighten it
@@FitnessTechnologyServices Thank you!
where could i get a belt like the one you use in the video for a t30 tm76d?
whole model number TM76D-B04041128
@@jeremytaylor6852 I can get that I don’t like posting prices or addresses on UA-cam send me your address to my gmail Fitnesspartspro@gmail.com
But why cut the old belt after seeing only having to lift deck to put on new belt also after removing the back roller completely I thought it would’ve been easier to just slacken the front .like u said when working on the road ,time is everything but still very informative thanks been a great help
Well no good reason really,no one has ever asked me that before 🤔.But it is faster and you can’t reuse it, except for it makes a great grass blocker under stone walkway. And thanks please subscribe Dave
Hi! I can’t see what the static guard strap looks like. I see you unscrew something and place it under the treadmill where I can’t see what it is shaped like. But, I got this far with the video really well!
Well it is a thin strap that mounts to the deck I don’t know if all horizon units have it I do have a better view on horizon 101 replacement
Would this treadmill be pretty similar to the Horizon CT5.0 layout? I need a new belt so i am hoping that I could follow this when I get my new one. I'm a first timer at changing a belt!
Well should be I also have ones on sole and Nordic Track all are pretty close
What is the name of the manufacturer of the belt you used or let me know how to order from your web sight
Well both of us would need your model and serial number to see what size . Sometimes are belt is too thick and heavy send information to Fitnesspartspro@ gmail.com
@@FitnessTechnologyServices horizon dt850
@@tuccan1 There should be a longer model number also. Look on the frame by the power cord also on horizon the serial number is important it is TM and a long set of numbers after
Where would you recommend getting a belt replacement belt for a T203? Thanks for the vid!
Morning, Glad the video was helpful. I also put a link to my channel. If you have a moment please SUBSCRIBE as it really helps me. Of course I can help you with any of your fitness equipment questions and parts. Well I can make one for you I would need the full serial # and the length and width. I will add a link to measure. Thanks Dave
MEASURING TREADMILL WALK BELT
ua-cam.com/video/SGo3Vb1apFE/v-deo.html
Treadmill walk belt comparison
ua-cam.com/video/R-JeRjZQ0io/v-deo.htmlua-cam.com/channels/Eubtuz3EILUAT8KamxKpPQ.htmlvideos
Realistically, how long does it take for someone who has medium skill level
Maybe 2 hours.
You should have mentioned that the belt should be checked to see if it's directional. You likely know that and may have checked when you got the belt, but anyone doing it for the first time might miss that detail.
Very few belt are directional! This one is not so no need to mention it on a unit that doesn’t require it. Most of the units I work on don’t maybe commercial? I have not seen one in 15 years
Sir how to install in treadmill speedometer
I don’t think they make a speedometer send me a picture of the sensor you are talking about. To Fitnesspartspro@gmail.com for better help
Is horizon t101?
No it is a older live strong 2009
very beefy machine
Great video, I got the belt on and running, have two left over parts though that I can’t remember where there go, any suggestions on where I can go to figure that out?
Hmm you will have to send me a picture
Great video, I got the belt on and running, have two left over parts though that I can’t remember where there go, any suggestions on where I can go to figure that out?
Well that’s hard ,send me a pic maybe?