This was 100% my problem. Has worked flawlessly ever since. Hope this helps someone else. The "valve" in the tube is a flapper type one way valve....fyi. It should allow water out but not back in.
Thank you, mine doesn't get standing water but I do get water in the filter area. I understand some but it just recently smells like it has old milk in it within a few hours of running. Pulling it out now!!!
GREAT HELP!!! This was my exact issue!!…. Appliance only 2 years old…No build up, Nothing blocking it, but using the wooden skewer I somehow brought that valve to full function/closing..💪🏼🥳. I owe you💰
This was exactly my issue and I NEVER would have figured this out. I found another video how to take off bottom of dishwasher. That way I could easily access the hose. THANK YOU!
Update: Had this happen to the dishwasher again today. Came back to watch my own video to take it apart and diagnose. Was a sticker from one of my kids cup this time stuck in the same spot. It can happen again!! Easy fix
Thanks for the video. Worked out. I didn't have to take off the piece inside. All I did was unscrew the screws that held the dishwasher in place, slide it out and lay it on it's side, pull off the left side metal plate, popped off the bottom panel and dried it off, took off the sensor and made sure that was dry as well, put the sensor back on, unhooked the squeeze clamps on both ends of the drain hose, ran water through the hose so it flushed the back flow preventer, blew back through the hose to make sure the air couldn't get through, put it all back together and that when the magic worked.
That's wild you figured that out. I've spent $130 on parts trying to DIY fix ours. So many problems with this unit. I took so much apart and realized that build-up is everywhere. The original owners NEVER ran vinegar rinses every quarter. Our Diverter motor part DD31-00013D or the Micro Switch DD34-00006A gave out, I replaced both and the unit is now fully cycling.
Update my problem is solve it was not a pump or hose, it was where the hose connect to the SINK connector, it was block. I took a small screwdriver and push it in that inlet and its solve my issue. Thanks to this video it help me a lot.
Thank you for introducing me to the check valve. Without knowing about the internal drain hose’s check valve, I would’ve been lost. I had assumed the plastic plumbing on the side would handle the water spill back. Unfortunately, I couldn’t clean the hose, and the check valve was worn out. Moreover, I had trouble finding a replacement hose. In the end, I improvised by using a shark bite check valve, PEX, and the rubber ends from the old hose. It worked perfectly and was much more cost-effective than buying a new hose or dishwasher. Once again, thank you for the helpful video!
Thank you for the video, my dishwasher had a small piece of metal stuck in the drain pump :-( cleaned it and works like a charm. And the Samsung rep told me that there is a seal leak and cannot be fixed :-/ and had to be replaced !!! Your video helped me trouble shoot in detail.
They just want to sell u more product. Apple does that w the Genius Bar. They don't fix anything. They sell u a service of "parts". Then send ur old part to China. Cuz that's where most used cell phones go and all Apple products to salvage parts. It's legal to sell disassembled tech, not here. Apple has contracts so u can't.
We couldn’t get anyone to repair our Samsung DW80K7050 after it stopped draining and decided to try to fix it ourselves. This video is a Godsend! I’ve been noticing standing water in the drain after cleaning the filter-for YEARS! I didn’t think it should be there but what do I know? We’re going to follow these instructions tomorrow and will let you know if we’re successful.
Great video. Just got hit with this issue on our Samsung so will try your inspection steps over the weekend and report back. Cheers and glad you got it working again!
Thank you Robert! My family has had this same dishwasher for years and it has been horrible! It has NEVER fully drained and ends up with a disgusting smell. My parents brought different plumbers and one even came 2 or 3 times and never fixed it yet always billing hundreds of dollars for wasting our time and his 👀. Thank goodness for this video and UA-cam.
Great video!😃 On my dishwasher, I think water was leaking past the big rubber O-Ring that seals the connection of the neck of the big, flat, white plastic tray on the side of the dishwasher and the plastic "drain" cover on the inside left wall of the dishwasher. I put clear silicon LOCTITE waterproof sealant on the O-Ring, pressed the neck of the big, white plastic tray into the circular hole on the side of the dishwasher and through to the other side, then put LOCTITE around the neck of the white tray. I then screwed on the plastic "drain" cover and spread more LOCTITE around it to make the best seal possible. I don't know if this will work, but it's the only other possible source of a water leak that I could find. Thanks again!😄
Our just displayed the code last night. Checked the valve, which was ok. There was a little bit of water in the bottom tray where the leak detection sensor was. Cleaned that out and checked for any visible signs of leaking. Put back together and running several test cycles. Thanks for the video, it should be at least where to start. Good work!
I ran into this exact problem,,, we went through everything checked drain pump, pulled off same hose, not only had a wet vac been to it, I coupled over my hand and blew through it and ran water from sink... replaced the case break as that is usually a culprit for a plug... removed and checked entire drain hose... it would still drain but still too much restriction... first time ever had to replace that piece and I work as a servicer for many brands and usually this is not a common problem, case breaks and drain pumps are. Excellent video by the way in both explanation and recording...
@@LandsharkLark yes, as I didnt even try to force anything through thinking that may damage it to begin with but like I said it would drain but was restricted and not draining quickly enough. Yes case break is the general term for that plastic assembly where water is monitored coming in and then draining out.
@@tigerdefensesystems Awesome. Good to know. I did think i damaged it at first. Had to adjust it back into the correct place and all was well after. Thanks for the reply!
Most generally yes, they should be clear... usually when they get some age and use you'll see anything from rust stains, to grease blockages, possibly mold or anything that might have blocked its way. Try taking air blow through it. Most generally I just replace. Do a google search on Samsung Case break click on images to look at new part images see what they look like.
THIS MAKES TOTAL SENCE. OUR DW IS PLUMBED IN THE DISPOSAL AND IT WAS CLOGED YOU. I CLEANED IT OUT AND THEN LC CODE STARTED SHOWING UP. IM GOING TO LOOK AT IT IN THE AM SINCE I FOUND THIS DIY, GENIUS IDEA TOO LATE IN THE EVENING. THANKS FOR SHOWING IT. MINE CAN PUMP IT OUT BUT IT WILL FILL THE CATCH BASKET BACK UP WHICH LIKE I SAID MAKES TOTAL SENCE. THANK YOU.
@@LandsharkLark I have the same model as was in the video. No one could verify that there was a check valve in the hose. I had ran a very long zip tie though it but it cane out both ends. I went and baught a borascope and looked for myself and found a straight shot. No check valve. I re installed the hose and it would not re- seal so I put a new screw clamp on it. I watched another video and that guy said his screws had loosened up on his drain pump. So I gave then a nice little twist with a Philips head screw driver and no leaks yet. It has been a week now and no code for water leaks.
I THINK I FOUND MY PROBLEM. THE HOSE I TOOK OFF WOULD NOT SEAL BACK SO UHAD TO USE THE SCREW STYLE CLAMP. I ALSO WENT AND CHECKED THE SCREWS HOLDING THE "PUMP" TO THE FLOOR OF THE UNIT. FOUND THESE SCREWS WERE LOOSE. I JUST HOPE THE SEAL IS STILL GOOD. AT A COST IF $188 FOR AN O-RING I SURE HOPE SO. THANK YOU FOR ALL THE HINTS AND TIPS. WHAT A PAIN IN THE TAIL. BUT A WHOLELOT CHEAPER THEN A NEW DISHWASHER.
Thanks for the heads up on my POS washer. My tube was pretty much clogged and the check valve was disintegrated somehow. Gonna put it back together without the check valve so I can do some dishes while I order a new one. Again thanks for narrowing it down for me
@@LandsharkLark I only get a little bit of water back in it now. Not perfect but it’ll get me through the next four days till the new one gets here. It’s about a half a gallon of clean water in it now as opposed to being filled to the brim with soupy food water
I think what Mr. Larkin is trying to say to us gentlemen... is to make sure YOUR WIFE PRERINSES THE DAMN DISHES BEFORE SHE PUTS THEM IN!!. Thank you sir, my dishwasher has been sitting for a while (same model). I'm going to go ahead and get to it
Mine seems to drain ok, but there is always some water left in the bottom of the filter basket. Does your do the same thing or does it drain until dry?
Do you think the rest of us should wait till we get this problem or work on it preemptively? Dang I just installed the dishwasher back in and didn't realize this was another place there would be build-up.
Ok I promise my last question ( I just can't believe I found another owner of this same unit and actually knows mostly what he is doing). When we moved into the house, the dishwasher has a rubber flap hanging. I cannot in any retail photo see a rubber flap hanging, every photos from Samsung shows the kick plate. Is the rubber flap hanging from the door supposed to be suspended above the kick plate?
I think it is supposed to be tucked up. But after working on mine, it also have the rubber flap hanging down. Hasn't bothered me, but maybe i will take a look at it tomorrow and give an update
Be careful as my drain hose with the flapper valve was not flexible and snapped. Forgot I had a wifi endoscope I could have used. The valve was gummed up and didn't operate well. I ended up having to replace both the drain hose with valve and drain pump because that is where my leak was. I thought I had the correct drain hose but this one is approximately two inches longer but identical PN DD81-01502A. I was able to make it fit without too much of a bind in the hose.
Ok thank you! I got ahead of myself and didn’t watch that far. Luckily I didn’t have to. Fixed it just by sucking the hoses out. I appreciate your help. The video was very helpful!
Its a rubber flapper valve. Should only have water flow in one direction if its seated properly. Try compressed air or a long thin object to see if something is making it stick. Then flush and make sure the flapper valve is seated properly.
@@LandsharkLark, I got it I could not get air in any direction, I took the hose off and slammed it onto my counter and something flew out, then I could blow air through one way but not the other way, so far so good
![[SOLVED] How to fix Samsung dishwasher oE error code - no parts](http://i.ytimg.com/vi/V04PvdyWVTM/mqdefault.jpg)
This was 100% my problem. Has worked flawlessly ever since. Hope this helps someone else. The "valve" in the tube is a flapper type one way valve....fyi. It should allow water out but not back in.
Thank you, mine doesn't get standing water but I do get water in the filter area. I understand some but it just recently smells like it has old milk in it within a few hours of running. Pulling it out now!!!
GREAT HELP!!! This was my exact issue!!…. Appliance only 2 years old…No build up, Nothing blocking it, but using the wooden skewer I somehow brought that valve to full function/closing..💪🏼🥳. I owe you💰
This was exactly my issue and I NEVER would have figured this out. I found another video how to take off bottom of dishwasher. That way I could easily access the hose. THANK YOU!
You are the hero we dont deserve, but need informative great camera work and short and to the point
Update: Had this happen to the dishwasher again today. Came back to watch my own video to take it apart and diagnose. Was a sticker from one of my kids cup this time stuck in the same spot. It can happen again!! Easy fix
Thanks for the video. Worked out. I didn't have to take off the piece inside. All I did was unscrew the screws that held the dishwasher in place, slide it out and lay it on it's side, pull off the left side metal plate, popped off the bottom panel and dried it off, took off the sensor and made sure that was dry as well, put the sensor back on, unhooked the squeeze clamps on both ends of the drain hose, ran water through the hose so it flushed the back flow preventer, blew back through the hose to make sure the air couldn't get through, put it all back together and that when the magic worked.
Thanks a bunch! This was my problem!!!!! Saved me a fortune in repair costs!👊🏼👊🏼👊🏼👊🏼👊🏼
That's wild you figured that out. I've spent $130 on parts trying to DIY fix ours. So many problems with this unit. I took so much apart and realized that build-up is everywhere. The original owners NEVER ran vinegar rinses every quarter. Our Diverter motor part DD31-00013D or the Micro Switch DD34-00006A gave out, I replaced both and the unit is now fully cycling.
Update my problem is solve it was not a pump or hose, it was where the hose connect to the SINK connector, it was block. I took a small screwdriver and push it in that inlet and its solve my issue. Thanks to this video it help me a lot.
Thank you for introducing me to the check valve. Without knowing about the internal drain hose’s check valve, I would’ve been lost. I had assumed the plastic plumbing on the side would handle the water spill back. Unfortunately, I couldn’t clean the hose, and the check valve was worn out. Moreover, I had trouble finding a replacement hose. In the end, I improvised by using a shark bite check valve, PEX, and the rubber ends from the old hose. It worked perfectly and was much more cost-effective than buying a new hose or dishwasher. Once again, thank you for the helpful video!
How would you connect the rubber ends of the old hose to PEX?
@@chrisbrose1769 hose clamps
Thank you for the video, my dishwasher had a small piece of metal stuck in the drain pump :-( cleaned it and works like a charm. And the Samsung rep told me that there is a seal leak and cannot be fixed :-/ and had to be replaced !!! Your video helped me trouble shoot in detail.
They just want to sell u more product. Apple does that w the Genius Bar. They don't fix anything. They sell u a service of "parts". Then send ur old part to China. Cuz that's where most used cell phones go and all Apple products to salvage parts. It's legal to sell disassembled tech, not here. Apple has contracts so u can't.
We couldn’t get anyone to repair our Samsung DW80K7050 after it stopped draining and decided to try to fix it ourselves. This video is a Godsend! I’ve been noticing standing water in the drain after cleaning the filter-for YEARS! I didn’t think it should be there but what do I know? We’re going to follow these instructions tomorrow and will let you know if we’re successful.
How did it go? Same exact problem since we have owned this Samsung dishwasher for years also. We're going to try it tonight.
Great video. Just got hit with this issue on our Samsung so will try your inspection steps over the weekend and report back. Cheers and glad you got it working again!
Thank you for sharing this! Just got mine back together and test ran. This was all that was wrong with mine.
You, sir, are a gentleman and a scholar! Thanks for the awesome video!
Thank you Robert! My family has had this same dishwasher for years and it has been horrible! It has NEVER fully drained and ends up with a disgusting smell. My parents brought different plumbers and one even came 2 or 3 times and never fixed it yet always billing hundreds of dollars for wasting our time and his 👀. Thank goodness for this video and UA-cam.
My pleasure. Glad I could help
Great video!😃
On my dishwasher, I think water was leaking past the big rubber O-Ring that seals the connection of the neck of the big, flat, white plastic tray on the side of the dishwasher and the plastic "drain" cover on the inside left wall of the dishwasher. I put clear silicon LOCTITE waterproof sealant on the O-Ring, pressed the neck of the big, white plastic tray into the circular hole on the side of the dishwasher and through to the other side, then put LOCTITE around the neck of the white tray. I then screwed on the plastic "drain" cover and spread more LOCTITE around it to make the best seal possible. I don't know if this will work, but it's the only other possible source of a water leak that I could find. Thanks again!😄
Our just displayed the code last night. Checked the valve, which was ok. There was a little bit of water in the bottom tray where the leak detection sensor was. Cleaned that out and checked for any visible signs of leaking. Put back together and running several test cycles. Thanks for the video, it should be at least where to start. Good work!
Mine also had water at the bottom I’ve already gotten the LC code thrown at me once. My check valve is fine did yours work properly after??
I ran into this exact problem,,, we went through everything checked drain pump, pulled off same hose, not only had a wet vac been to it, I coupled over my hand and blew through it and ran water from sink... replaced the case break as that is usually a culprit for a plug... removed and checked entire drain hose... it would still drain but still too much restriction... first time ever had to replace that piece and I work as a servicer for many brands and usually this is not a common problem, case breaks and drain pumps are. Excellent video by the way in both explanation and recording...
Thanks for the comment. So you replaced the whole hose and that solved the problem?
@@LandsharkLark yes, as I didnt even try to force anything through thinking that may damage it to begin with but like I said it would drain but was restricted and not draining quickly enough. Yes case break is the general term for that plastic assembly where water is monitored coming in and then draining out.
@@tigerdefensesystems Awesome. Good to know. I did think i damaged it at first. Had to adjust it back into the correct place and all was well after. Thanks for the reply!
@@tigerdefensesystems is the case break supposed to be clean all the way through? Mine looks like it has some black stuff in some of the channels
Most generally yes, they should be clear... usually when they get some age and use you'll see anything from rust stains, to grease blockages, possibly mold or anything that might have blocked its way. Try taking air blow through it. Most generally I just replace. Do a google search on Samsung Case break click on images to look at new part images see what they look like.
This help me out! I didnt know about the hose having a valve. I replaced the hose and installed it the wrong way.
THIS MAKES TOTAL SENCE. OUR DW IS PLUMBED IN THE DISPOSAL AND IT WAS CLOGED YOU. I CLEANED IT OUT AND THEN LC CODE STARTED SHOWING UP. IM GOING TO LOOK AT IT IN THE AM SINCE I FOUND THIS DIY, GENIUS IDEA TOO LATE IN THE EVENING. THANKS FOR SHOWING IT. MINE CAN PUMP IT OUT BUT IT WILL FILL THE CATCH BASKET BACK UP WHICH LIKE I SAID MAKES TOTAL SENCE. THANK YOU.
Did this work out for you?
@@LandsharkLark I have the same model as was in the video. No one could verify that there was a check valve in the hose. I had ran a very long zip tie though it but it cane out both ends. I went and baught a borascope and looked for myself and found a straight shot. No check valve. I re installed the hose and it would not re- seal so I put a new screw clamp on it. I watched another video and that guy said his screws had loosened up on his drain pump. So I gave then a nice little twist with a Philips head screw driver and no leaks yet. It has been a week now and no code for water leaks.
I THINK I FOUND MY PROBLEM. THE HOSE I TOOK OFF WOULD NOT SEAL BACK SO UHAD TO USE THE SCREW STYLE CLAMP. I ALSO WENT AND CHECKED THE SCREWS HOLDING THE "PUMP" TO THE FLOOR OF THE UNIT. FOUND THESE SCREWS WERE LOOSE. I JUST HOPE THE SEAL IS STILL GOOD. AT A COST IF $188 FOR AN O-RING I SURE HOPE SO. THANK YOU FOR ALL THE HINTS AND TIPS. WHAT A PAIN IN THE TAIL. BUT A WHOLELOT CHEAPER THEN A NEW DISHWASHER.
Huge help!
Thanks for making this video!
This was our problem thank you for your video it fixed the problem
No problem. Glad it helped
Thank you so much for your help!
Thanks for the heads up on my POS washer. My tube was pretty much clogged and the check valve was disintegrated somehow. Gonna put it back together without the check valve so I can do some dishes while I order a new one. Again thanks for narrowing it down for me
No problem. But it will overflow from backwash without the check valve
@@LandsharkLark I only get a little bit of water back in it now. Not perfect but it’ll get me through the next four days till the new one gets here. It’s about a half a gallon of clean water in it now as opposed to being filled to the brim with soupy food water
@@Kevin_Casey I can't find the part anywhere.
good diagnose .... repair on👍🔧
I just did the step in the video, First cycle ran successfully.
Great job!!!!
In Samsung dishwashers the initial problem seems to clear and migrate to the next stage, and cause a fault. It's a step by step clear and that works.
I have this same dishwasher and I hate it. I'm going to give this a shot, hopefully it works, will update of it does. Fingers crossed 🤞
Good luck
I think what Mr. Larkin is trying to say to us gentlemen... is to make sure YOUR WIFE PRERINSES THE DAMN DISHES BEFORE SHE PUTS THEM IN!!. Thank you sir, my dishwasher has been sitting for a while (same model). I'm going to go ahead and get to it
Mine seems to drain ok, but there is always some water left in the bottom of the filter basket. Does your do the same thing or does it drain until dry?
Any idea what the valve hose part number is? Mine had a small crack
Mommy thanks you my friend
I have the same exact dishwasher I took out the exact same part you showed but there is no valve the tube is wide-open
Update, I just replace the Pump and it sound better, well a lot more suction when draining.
And your check valve problem was causing the LC error code (Leak detection) to show up and the DW was always in draining cycle?
Yes
Do you have a part number?
does the dishwasher overflow on to the floor when this happens
Do you think the rest of us should wait till we get this problem or work on it preemptively? Dang I just installed the dishwasher back in and didn't realize this was another place there would be build-up.
I would honestly wait. I think it's case by case. Fine one minute, then suddenly something gets caught in the flap and you have standing water inside.
What is the hose called
Ok I promise my last question ( I just can't believe I found another owner of this same unit and actually knows mostly what he is doing). When we moved into the house, the dishwasher has a rubber flap hanging. I cannot in any retail photo see a rubber flap hanging, every photos from Samsung shows the kick plate. Is the rubber flap hanging from the door supposed to be suspended above the kick plate?
I think it is supposed to be tucked up. But after working on mine, it also have the rubber flap hanging down. Hasn't bothered me, but maybe i will take a look at it tomorrow and give an update
Be careful as my drain hose with the flapper valve was not flexible and snapped. Forgot I had a wifi endoscope I could have used. The valve was gummed up and didn't operate well. I ended up having to replace both the drain hose with valve and drain pump because that is where my leak was. I thought I had the correct drain hose but this one is approximately two inches longer but identical PN DD81-01502A. I was able to make it fit without too much of a bind in the hose.
Thanks! Had a mouse chew through this hose today! I'll be trying this part for my washer
Do you happen to have part number for this hose? I've looked everywhere can't find it.
Mine is missing flapper. Can't find a replacement hose anywhere.
Yea thanks a ton for the video man!! I'm literally having the exact same problem myself. Def about to try this myself
How is that big white plastic piece attached? I’ve loosened the hoses but this thing isn’t budging.
4:20 in the video I explain it.
Ok thank you! I got ahead of myself and didn’t watch that far. Luckily I didn’t have to. Fixed it just by sucking the hoses out. I appreciate your help. The video was very helpful!
Can someone please provide the size/dimensions of this particular dishwasher? Please
Well did it keep working correctly???
Yes!! Has been working perfect ever since.
I ran water through my line and I cant get water flow in either direction does this mean the valve is bad
Its a rubber flapper valve. Should only have water flow in one direction if its seated properly. Try compressed air or a long thin object to see if something is making it stick. Then flush and make sure the flapper valve is seated properly.
@@LandsharkLark, I got it I could not get air in any direction, I took the hose off and slammed it onto my counter and something flew out, then I could blow air through one way but not the other way, so far so good
thank you for your video
@@chuckb2175 Great! No problem.
Also, is your dishwasher still working okay?
Yep
The replacement hose is: DD81-01502A
Not for that model is too long.for thus model they don't sell the hose it come assembly and discontinue by samsung
@@VisualQC75 It's SLIGHTLY too long, but it works.
I replaced the part and nope. Had to replace the drain pump.
Did anyone experience water damage because of this problem?
Mine doesn’t even start the drain pump when I start the machine