Whirlpool WDT720PADM1 Dishwasher Not Working Repair
Вставка
- Опубліковано 19 вер 2017
- amzn.to/2x6XePK Circulation Pump (dishes not getting clean)
amzn.to/2fplGnJ Complete pump and motor assembly
amzn.to/2wx1Qwv Doorlatch
amzn.to/2xamzK7 Circuit Board (Main control board)
amzn.to/2x6XePK Circulation Pump (dishes not getting clean)
amzn.to/2xpVAuB Drain Pump (dishwasher not draining)
amzn.to/2jA3xbA Dishwasher detergent dispenser
amzn.to/2x7eq7E Water Inlet Valve (Many times Cracked)
amzn.to/2yfrvvE Inlet Valve Solenoid (Dishwasher no fill)
amzn.to/2yeBeTj Push button Panel (almost always what is wrong vs. main control board buttons wear out or get stuck over time)
Help support Doublewide6 Repairs LLC by sponsoring his Patreon account
/ doublewide6
Doublewide6 Repairs LLC has a Master’s Degree in industrial technology with a specialization in Manufacturing, due to factors beyond the control of Doublewide6 Repairs LLC and anyone featured in his videos, I cannot guarantee against improper use or unauthorized modifications of this information. Doublewide6 Repairs LLC assumes no liability for property damage or injury incurred as a result of any of the information contained in this video or any of Doublewide6’ Repairs LLC's videos. Use this information at your own risk. Doublewide6 Repairs LLC recommends safe practices when working on equipment, power tools, chemicals, electronics, electrical systems, vehicles, and or with tools seen or implied in this video. Due to factors beyond the control of Doublewide6 Repairs LLC, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Doublewide6 Repairs LLC.
amzn.to/2x6XePK Circulation Pump (dishes not getting clean)
amzn.to/2fplGnJ Complete pump and motor assembly
amzn.to/2wx1Qwv Doorlatch
amzn.to/2xamzK7 Circuit Board (Main control board)
amzn.to/2x6XePK Circulation Pump (dishes not getting clean)
amzn.to/2xpVAuB Drain Pump (dishwasher not draining)
amzn.to/2jA3xbA Dishwasher detergent dispenser
amzn.to/2x7eq7E Water Inlet Valve (Many times Cracked)
amzn.to/2yfrvvE Inlet Valve Solenoid (Dishwasher no fill)
amzn.to/2yeBeTj Push button Panel (almost always what is wrong vs. main control board buttons wear out or get stuck over time)
Help support Doublewide6 Repairs LLC by sponsoring his Patreon account
www.patreon.com/doublewide6
You would think that these cheap bearings would be available to purchase separately since it's a common problem. Even if it's a bad design, these things would be like $1.
I’m thinking about buying one just like this used and the guy said it works good other than there is some detergent that is still in the detergent dispenser after it finishes it’s cycle. I thought it may be the circulation pump. What do you think??
Thanks for this, man. Concise and unpretentious. I hope your name pops up again for the next appliance repair I run into.
I am a young mom and was able to fix my dishwasher by watching your video. Thank you, thank you!!!
Brother, just wanted to come back to say thank you. I have a Whirlpool with the same pump/issue that, thanks to your video, i fixed with an $80 part and an hour of my time. thank you for what you do, man.
Great video, first and only one I have found for the Whirlpool WDT720PADM dishwasher that actually talks about the pump and taking it apart and the parts that makes it up. I am an engineer and have done bench repair of electronics to component level for a years. Sad we live in a throw away society now where seems no one wants to fix things that are not that hard to do so. For electronics it is easy there are many parts companies that will sell just about any part you want but on things like this which is actually a common pump you cannot find a common part.
I was so close to buying new dishwasher. Thank you for the video! Running as if it was just pulled out the box.
Really appreciate the video! Was having issue with my whirlpool dishwasher not "washing" but filling and draining.
I was going to just order a circulation pump but figured I would give cleaning it a try. It was NASTY, for real. Only 2 years old. Cleaned it out, temporarily hooked it back up for a test run and BOOM I could definetly hear the blades spinning.
Need 2 hose clamps though. The 1 you replaced and 1 for the other end that doesn't normally have a hose clamp. Must have been glued in or something but it's leaking from there. Might try a metal "zip tie" due to the tight clearance. Unsure if there is a glue that would work but ill double check.
Thanks again for the video my man! Saved me $120 which was about the cheapest I could find a circulation pump for. Never mind the amount of money I was fixin to spend if I was just going to buy a new dishwasher.
Thank you for the video. The circulation pump was out on my dishwasher. Easy to watch and learn video. Found the part on McCombs Supply for $47. My dishwasher works now- no leaks! Happy New Year
Thank you for posting where you got the part from. Saved me $100!
I just wanted to say thank for this video. U saved me a lot of money. The part was very easy to replace.
Great video I just fixed my wash motor by replacing the bushing with an rc car wheel bushing.
link to the bushing that fits please?
Just wanted to thank you for the video. I have the same model and it is only 1 1/2 years old also. I took off the pump and checked on getting a new pump, and the cheapest I could find with shipping was $100.00. I only paid $375.00 for this dishwasher new (found a deal at HD) but eventually be changing it out because I'm remodeling our kitchen. So I couldn't bring myself to buy a new pump until I tried something first. In your video you said it was just the bushing that is the problem on the pump, so I made a new bushing out of a stainless steel bolt. So far so good. I've run 3 loads through and the dishwasher hasn't worked this well in a long time! Well, hopefully it will last a while. Thanks again.
Hello can you describe the type bolt you made a bushing out of? Maybe you mean a washer?
Thanks for this mate. I pulled it apart and cleaned the impeller as per your instructions and as I sit here it is making all the right noises.....and not leaking! Lets see.......thanks again.
Thank you very much for this video. Just fixed my own dishwasher and saved a few hundred bucks!
Mine didn't need screws its held in place by forcing it into the housing. I took the piece apart and the magnet was rusty and there was food in there. I cleaned all the food out and cleaned the magnet so it was smooth again. I put in a little water proof grease around it and put it all together. I forgot how forceful the water pressure is in there. I would buy you a pitcher of beer and wings for this video. Thank you a 100 times.
Is there a check valve? I can't seem to find one. I changed the pump, it runs and the lines are clear, yet there just isn't enough pressure to drive the water through.
Thanks man. Used this guide to replace my pump.
Dude. So helpful. This is exactly what’s wrong with mine.
Thanks man! You just save me a bunch of money! Cheers
A year and a half and the pump is already shot?! Boy, things are really made to break down these days aren't they? I just swapped the bearings on my 1997 dishwasher that ended up seizing, it's running like new again. 26 years old.
Man, you're right! Those dishwasher prices have hit the roof. It's definitely worth the time and trouble to see if it's a simple fix, or even one that's not so simple for that matter. Thanks, Bob!!
This was a fun project for me, not really my expertise but as always something was learned.
An appliance commercial came up before this one. Good timing. Wow 1 1/2 years old is NOT good. Remember when the fridge from Grandma's house was downstairs still working and upstairs 3 fridges have come and gone.
That is very true. These new appliances have all kinds of sensors and stop working because something is not right. I used to take about an hour to wash our clothes now with the high efficiency washer it takes close to 2 hours.
Thanks for the great video. That was exactly our problem as well. $49 from Amazon and sprung for a 3 year warranty for $6. As poorly as they are made I’m sure we will be taking advantage of the warranty as we do at least a load a day. Thanks again!!
$49?! I'd like to know where you found the replacement part for that little...
@@Mondonitis Amazon
Thank you for your video. I have the same model and it helped me greatly.
Thanks for the video !
Keep 'em coming.
Okay thanks for taking the time to comment.
I made that bearing/bushing with my 3d printer and it’s been working for 2 years.
Great video, you can actually fill up the bushings with rtv silicone then drill a hole with a same size of the shaft to keep the shaft tight
I just did this repair (thank you for the video!), and water is pouring out of the connection w/o the hose clamp. The pump went on easy, just like you demonstrated, but that connection is far from water tight. Any suggestions?
A year and a half old machine. This model came with my home as new 4 years ago. Now it's not drying. They don't make anything to last.
Quick question: Does this pump/morot problem cause water leakage by any chance. I have same model and I don't see any water in the front when I use the machine but by my neighbor came upstairs seeing water coming down from his ceiling. so not sure what is going on. Thank you for the video. Appreciate it.
Will this pump work on a WDT720PADM0? Thank you!
Bushings shot on mine too.
I know this video is 4yrs old, but hopefully I’ll get a reply. Will this pump be the reason my dishwasher isn’t getting any water?
Is this pump near the back or the front?
I have mod # WDT720PADMO. WILL this work on that machine.
How can I tell if the problem is a $20 inlet valve?
I have exactly the same problem with my same model dishwasher, it is also 1.5 years old. after seen the bearing of the pump in this video i will never by appliances from Whirlpool / Frigidaire again. Ill pay a bit more and get a samsung / LG . I had samsung dishwasher that worked flawless for 7 years, sadly i had to leave it when i moved.
Do you have the dimensions of the bearing? Could it be printed?
My Whirlpool dishwasher has been throwing a F6E4..
Door latch switch is good
Float switch replaced
Drain pump good
Mother board replaced
Fully cleaned, turbidity sensor cleaned...
Water valve replaced
Running out of ideas.
Any suggestions?
If you are ever able to source a fix for the old pump to have on hand as a back that would make a good vid. 80$ once is ok, but if this goes again, a even cheaper solution could be useful.
Good thought, but I'm not keeping this dishwasher. I have an older one that is working fine and it has a much stronger and better made motor.
Mine doesn't have power.. where is the fuse on this model I can't find it? Thanks
hi they don't make dishwashers like they used to the old ones were heavy and strong they have such a big motor on them the old ones took two hands to hold the motor that's when they were American made that dishwasher pump motor you have looks like a little bitty toy pump motor let me guess made in China or some foreign country yeah and that's what companies do you cannot buy the part you got by the whole unit I like to see a hundred percent American made or Germany or Russia or one of the big countries who know how to make good quality and stuff
You are right, they used to be built much better and would last a lot longer. They didn't cost $500 back then either.
mine, made in 2016 In the USA (stamped on front door), has the same crappy pump and issue.
Just did the same repair on my dishwasher WDF760SAD82, it was fairly easy to get at and replace the motor, but shame on WP for making such a terrible design flaw. Planned obsolescence! C'mon WP, stop pulling this crap!
So the meaning of all this is that this pump that costs 90$ has flaw design that will require me to replace it every 1.5 year. Hmmm,Thank you Whirlpool / Frigidaire I will never buy your appliances again.
My Maytag circulation pump just failed this week after owning it new for 19 months.
Same here. I have replaced a water inlet valve and pump on a 4 year old Whirlpool. I had my previous GE dishwasher for over 20 years. No repairs. Replaced it when remodeling the kitchen. What a mistake.
Easier yet, just replace motor by twisting it off/on. Wish I could buy just the motor without the rest of the housing, similar to the drain pump motor. If anyone knows where to get JUST THE MOTOR, please comment.
the pump can twist off of that mount
I’ve got a 2yr old Whirlpool Gold Series that has this problem. They are ruining their brand reputation over a cheap bearing. They are probably doing this on purpose to sell more motors.
My Dishwasher won’t start it pumps water but no cycle
It's practically criminal to design and sell something like this. The manufacturer probably saved less than a dollar by using those crappy bushings, when good Delrin or bronze bushings would last for many years with no problems. They also do the customer no favor by using hose clamps that require special tools to install.
My whirlpool dishwasher is 6 months old and failed. It fills and drains but does not spray water. I will take it apart and I hope it's just debris in the pump. If the pump failed at 6 months, I'll never buy whirlpool anything ever again.
My dishwasher has the same issue. Have you fixed it ? How?
The 12 month warranty should cover it. My Maytag lasted 19 months.
They make Crap these days, this needs to change.