You said there was no trigger “pull”, with this gun. That’s actually one of things that I like about it. Very little travel, distinct wall, and crisp break. No “mush”. Also, the reset is very short. All pluses, in my book…
It certainly makes for a more pleasant shooting experience. We describe and explain our experiences and leave it up to you if that's something you want or not.
We have been in contact with Taurus are are going to try another barrel. The more we shoot this the more likely it seems the chamber is out of spec. Stay tuned for a follow up video with a new barrel. Article: www.gbgunsdepot.com/post/taurus-gx4-enters-the-micro-compact-game
Not being in spec was found with a replacement Taurus G3C barrel from Lakeland! This was a Fan Boy for Taurus who had sent for another barrel for his factory provided barrel! This had proved to be not Lakeland but a Taurus not cut to spec! They were able to get another to fit the slide!
Long time handgun reloader here. Almost 40 years. The primer flow is a non-issue as far as reloading goes. The hole in the slide for the firing pin is larger than it needs to be and you get a little flow. As long as you stay within spec you'll be fine. If I saw that on a magnum revolver with lighter loads I would have a problem; but not in 9x19. The smile is less pronounced than a 40 Glock, or even an early 9mm Glock. Not a problem as long as you don't use the case for multiple really hot handloads. Again, almost no one reloads hot 9mm unless they are "making major" in a match gun, which certainly doesn't apply here. I haven't seen a case fail from smiley until the fourth or so hot load. You can see it progressing, so just watch your brass. The smoke ring is usually low pressure loads. An oversized chamber will do it too, which is common in defensive guns. The failure to return to battery is likely just debris of some sort; dirty gun, what have you. The one round that never chambered is obviously out of spec and doesn't reflect on the gun. Hopefully the new barrel fixes what ails this. And try the Arex Delta Gen 2; in this climate you can always sell a gun for list price.
@@11spitdms They can't import one do to the point system for handguns. But since the gun is modular they can sell micro grip modules and smaller slide assemblies. Look for them to do that when/if they get enough "base" models sold that they think they can turn a good number of conversions kits.
Long time shooting enthusiasts especially love shooting Pocket guns and Micro 9mms. Never owned a Taurus. However, after testing this gun with others at my club, I was a instant fanboy. Man I love this gun. IMO the very best Micro 9mm money can buy. I was shocked at the quality and shooting control. My new one now has over 700 rds of every thing I could find to put into it and not one single issue. NONE. Just recently bought the Toro Slide to go with it for only $149.00. Taurus obviously went into the competitive market to come out on TOP and that they did. They took the best of all the Micro's and put into this gun. Love the Trigger for EDC. What a unique design. I would not be surprised to see others try and copy it. I was not looking for a Budget gun and I did not get one, What I did get was a top quality gun at a budget price. I would have paid much more if that had been the cost.
Just picked up a GX4 after watching multiple reviews including yours. Took it to the range today for the first time after the initial field strip and lube and put 160 rounds on steel, including Federal AE 115gr FMJ, Remington UMC 124gr FMJ, Winchester WB 147gr Flat Nose and Fiocchi 115gr JHP. NO failures of any kind. The trigger was very good, perhaps a little grittiness in the initial take up, but after reaching the wall it broke crisply at my guess of about 5 lbs with minimal over travel. Reset was very short and tactile. The slide release was easy to manipulate during reloads unlike a lot of micros that are very stiff. POA/POI were right on once I figured out the sights seem to be regulated for a "combat" hold. I am by no means a marksman and despite my shaky old man hands I had no trouble hitting a 8" plate at 15 yards. After your discussion in the video about the primer blowout and "smiley face" marks on the brass, I checked several of my spent cases and they showed the same although the smileys were less visible than the one's you had. To the naked eye I didn't seen any bulging on any of the cases. All in all I am very impressed with the GX4. For me personally I find it fits me better, is easier to shoot well, and recoils less than my Kimber Micro 9 and carries 4 more rounds. I have ordered two of the pinky extensions from Taurus to get the full 3 finger grip (I only get 2 1/2 with the 11 round mag with the flat base plate) and am considering replacing the front sight with a fiber optic or painting it green or orange to make it easier to see. I had my choice narrowed down to the GX4 and the CZ P-10S. The CZ is a fine pistol in every respect and it was a toss up between the two but I went with the GX4 due its' slightly easier to conceal footprint. Maybe for Fathers Day I'll get myself the CZ!!
Thank you both for a very thorough and informative review! Love the balance that two people can provide. Also thanks for your contribution and sacrifices made for our great nation.
I hope so too. Sadly this was just supply we've held on to since 2019. We have 40 or so loads we rotate through, shooting just 3 at a time plus the lack of new guns recently has helped us milk the WFD supply.
Kudos to your more in depth review of this handgun. Your lovely shooting companion wasn't keen on the guns trigger but her shooting accuracy was impressive. Excellent review.👍
Thank you. I've learned that over time trigger drag improves and we did notice that the more we shot it the easier it became. Knowing a gun well is crucial in self defense.
Thanks Graham. I'm glad things turned out well, and there were no injuries. I know that some of the companies reduce chamber support to increase reliability. But if you do like Sign with the P365XL and split the difference between the feed ramp and the ejection side, you won't get the smile. The G3 is so well supported, that a wide mouthed HP bullet (also Lehigh XD, XP) will NOT chamber from a full mag for me. I definitely would not reload any casings from a gun that does not have a truly supported chamber. Primer hole is too big on that gun, Graham, that's why the primer is flowing back.
Took my GX4 out to the range, and found that once I felt comfortable with my hold and sight picture, accuracy at 15 yards was quite nice -- easily a good CCW. I had absolutely no malfunctions! I tried it with both back-straps, and preferred the smaller one. The larger one was a tad too large and the smaller one a tad too small. I used 124 gr ammo. IF Hogue comes out with a new grip that will stretch over the smaller backstrap, I bet it'll be the best of the three worlds.
I bought the Taurus G3. Glad I did. I love my Springfeild Armory Hellcat the best. You both are wonderful and very honest about what you review. Outstanding to all of us viewers to get truth and not media biased bologna.
I own a GX4 & a GX4 XL TORO I break in my 9mm pistols with 124gr ammo .. and I have ran lots of ammo through both of them Zero malfunctions …. These little pistols are not finicky Great pistols
You mentioned an extremely important thing that nobody else talks about. Ballistics. 9mm from a 4” barrel is one thing. Once you go to 3.5” (G26)things change and 147gr HP’s don’t always reliably expand, in my experience. I carry a 43x, 3.4” barrel, and that’s right on the line. 3.0”-3.1” are going to be a crap shoot. I wish people would do gel tests with the micros. I’m sure a 115gr-124gr +p would open up but probably not through all test mediums. Thank you for bringing this up.
It's a serious point. There are some great modern specialty loads designed to perform well at the lower speeds these shorties create, but they still don't deliver the energy that a longer barrel does. I personally don't carry less than a 4". I want my HPs to open and I want as much energy dumped into the target as possible.
Thank you and welcome to the channel! We test every gun in this format so you have a better idea of what you're getting into. More in depth than "it's a good or bad gun" descriptions without any scientific process to back up that conclusion.
Mine broke after 230 rounds. Sear snapped in half. Taurus charged me 50 to ship it for repair. Only gun company not paying for postage on warranty items. I've purchased 3 Taurus pistols and all 3 broke early on. They work great until failure. Then how do you trust for carry? Waste of money. Save up and buy something else. I bought a canik sc.....awesome.built like a tank.
It is bad that you have had such a bad experience with Taurus. Just my experience. I have bought close to 40 Taurus handguns and never had any issues but one. I bought 4 spectrum 380's and only one of the 4 was finecky with the ammo. I have revolvers, 9mm, 22, and 380's. I love Taurus. I also own P365, Hellcat, M&P 2.0. I love them all.
I've never had an issue with steel - Tula or Wolf in my Glock43, Beretta APX, as well as the Taurus G2C. Glad to see they work well in the Taurus GX4. The current deal with BudsGunShop of $209 after the $50 Taurus rebate make this a win-win in my book. Waiting on arrival now.
Great review and excellent presentation. Thanks for pointing out your observations regarding the casings, the barrel configuration, and variety of barrels. Thank you both for all you do. 🎩☯️♠️
I am a reloader and my initial thoughts are NO WAY would I shoot reloads out of this firearm. The lack of chamber support and blow back of the gasses are not safe in my opinion. This will not be a likely purchase for me or mine. Thanks you two for another great review.
Today @ about 1600 rounds my firing pin broke in the GX4. I noticed the firing pin drag on the struck primers when I fired my first shots and knew that was common on micro-compacts as firing pins were breaking but it wasn't a huge concern. Firing pins are cheap right? I have broken them in Glocks. This is the first Taurus I have owned in 33 years and only revolvers. Now, getting off the phone with Taurus and finding out they won't sell me a firing pin, I have to send them the gun, and it cost a lot to ship it that's not covered by the warranty, and it will take 4 to 8 weeks. Just to take two minutes to remove the back plate and change the firing pin assembly. It makes me realize I wasted my money buying a Taurus. I'm sticking with Glocks and Sigs. I can buy spare parts for those.
Excellent Review! Brass with a slight bulge at the belt like that should not be reloaded and will require more effort to resize. Case life will be shortened considerably and could cause a blowout. Not worth the effort to reload! Firing Pin hole in the Slide boltface is too large allowing the Primer metal to flow back. I have other Taurus Pistols with which I am pleased with, but I doubt I would buy a GX4. I often carry a 9mm Taurus Millennium Pro or a Canik TP9V1.
I went ahead and purchased one for close to MSRP and I am looking forward to shooting it. You mentioned in your shooting impressions video that the GX4 down not feel like a budget gun, it doesn't shoot like a budget gun and that is one of the reasons I bought it. I've enjoyed owing Taurus handguns through the years specifically the G2C, TX22 and the Beretta clone 92.
I have a pt111G2, a G3 and. G3X. As a big guy my favorite is the G3X for the 15+1 capacity and decent trigger. I’m thinking of going with the GX4 Carry as all the tests I’ve seen seem to point to the GX4 strengths and adding the 15 round capacity and accessory rail as on the G2 and 3. All the testers comment on the less barrel flip than comparable models and as you watch the videos it seems that it recoils straight back which may be due to the barrel being closer to the grip. Great review. It helps seeing a women give her take as often men don’t have the same likes and dislikes.
Good review. I'll stick with the G3C. I like the restrike capability of the G3C & this gun is new and has no long term history yet. The cartridge burn concerns me. Not just Taurus, but a lot of guns get produced before they have been thoroughly tested and developed.
If you look at the firing pin hole on the breach face you will notice an oblong chamfer with the largest part pointed down. This 'primer flow' look is caused by the shape of it. I'm not a fan of the unsupported chamber. I don't think these things will be a problem but only time will tell now that the pistol has been released.
We've been in touch with Taurus. The replaced our barrel. We will retest with the new barrel. If you look at our Tabletop video you can see the chamber fitment was off to being with. My guess is a short lead causing the projectile to be seated deeper by the force of chambering and resulting in slight over pressure.
My new gx4 jams like a rock band.Shot many brands about 800 rounds and jammed on all outings.Shot great when it fired.Also got trigger finger pinch.Back to taurus it goes
I bought mine same day I also bought a Hellcat Pro and was surprised it printed tighter groups than the Pro. Better trigger and grip angle so looking forward to also getting a Gx4 Carry.
Ok, now I've bought a new Taurus GX4 Micro Carry. My primers look just like yours, being my reloads or factory loaded ammo. If you look at the firing pin hole, you'll notice that it isn't round, but has some relief cut below the hole itself. Taurus says it's to help with any debris that may get in that area to fall out. It seems that they all have that relief cut in them, so your primers are actually normal, for a Taurus anyway. It also makes it look like you are getting light primer strikes, (Which I have had a few of), when you're not, because it also allows the dent in the primer to blow back out somewhat. I learned that my light strikes were due to primers not seated deep enough into the primer pocket. When you're loading range brass you are loading many different brands and makers of brass, and they are not all the same. In some cases, the primer actually seats below level with the head of the case. If that is done, it will fire them every time. You want to use a small primer ram to reload for this pistol so it can push the primers all the way to the seated position and if you do that it will be one hundred percent reliable. As far as your (Smiles), I've not noticed that, even with very hot loads. What I've found with my used G2C and the new GX4 is they are one hundred percent reliable.
Just a thought about the ammo. I have had some of the same issues with 22lr. It's like the manufacturers have had to loosen the specs a bit to produce more ammo. They can sure sell it.
Impressive review and extremely helpful. I purchased my GX4 yesterday and I prefer a small gun for a conceal carry/defensive situation because my hand fits better; however, I will try the bigger backstrap. Unfortunately, when I brought the gun home and went to load one of the magazines, it was defective, and I cannot even get one bullet into the magazine. I pray Taurus has improved their customer service from the first time I tried contacting them a few years ago about my Taurus G2.
@@GiselleMarieXIII That's great. I've heard things have improved. We had issues with this gun at first (we now have four videos on it) but Taurus took care of things quickly, and much better than my customer experience with them back in 2015.
I am an Avid reloader and was really thinking about buying this pistol. Had never seen a video before yours point out the chamber problem. (not being fully supported). One reason I'm not a big Glock fan. I own a G2C and for some reason I've never noticed a problem with guppy bellying with it at all. Maybe they changed their chamber dimensions on this one. But then they talk about the G2C having such a crappy trigger and I have no problem whatsoever with mine. No worse than any Glock I've ever shot anyway. And I own two Glocks.
I place the GX4 ahead of several "top tier" edc pistols (Glock 43x, SIG 365, Hellcat (not Pro) and MC9). I found it be a little snappy, but nothing like the 365 or Hellcat. I'm just more accurate with it than the Glock. The MC9 I just don't care for... More to do with ergonomics for me. I saw that they released an extended mag, that actually comes all the way back under the rear of the backstrap. That may change my mind on it somewhat, because the MC9 does have a really good trigger.
I just bought the GX4 and took it out to the range for the first time yesterday and shot it side by side with my Sig P365. I actually found that the Taurus fits my (medium) size hands better than the Sig, and with the Sig using my normal grip my support hand thumb always seems to be resting on the take down lever. You guys made this video a year ago and I'm wondering if Taurus has since made some adjustments to the trigger. My personal experience in my 200 round range session yesterday was absolutely outstanding, and I was able to shoot the GX4 more accurately than my P365 and lower recoil impulse. I did also notice the slightly bulged primers and the burn marks on one side of the spent shell casing, but I see the burn marks on several of my Glock casings too. I didn't have any issues of the pistol going into battery but wasn't shooting the same ammo as you guys. Great informative video guys! Nicely done and nice shooting!
Interesting you guys are the only ones that pointed out the anomalies on the brass and primers, and probably the only ones that fussed about the trigger pretty much everybody else really liked the trigger I guess a lot of it boils down to personal preference or what you really like.
I'm thinking that if the chamber isn't right on our barrel and bullets are being pushed into the case a bit during chambering, causing higher pressures. We have been in touch with Taurus and they are sending a new barrel. I've noticed in other reviews that other barrels were marked differently with "GX1", "GX0" etc. Ours is marked "GX3".
@@user-jetmachinist I don't think it's a mix up so much as there were different barrels made. That or the "media guns" we see out there had an earlier barrel design. I've seen some people say the "GX3" marking on our barrel is because it's a GX series gun, 3" barrel, but that doesn't explain why there are 3" barrels marked "GX1".
@@GBGuns the most plausible guess I read is it’s a milling machine number. If that’s the case and you get a bunch of barrels that fail QC you can quickly identify the out of spec machine by number and either repair it or take it out of service to repair it
I've reloaded 10's of thousands of rounds of 9mm. As long as you resize the cases there should be no issues. The leaking gas around the case will effect your velocity and even aim as the bullet may drop more as a result of lose of pressure around the casing, however this is very common with many small cal. auto guns. The primer flow is due to poor fit between the firing pin and hole bolt or slider and should be corrected in future by manufacture. No need for concern as long as there is no hole in primer after firing it. If you find a hole in primer be sure to have it repaired ASAP.
I an a reloader and I have experienced a lot worse cases, but from a Hi-Point. Brass from a 40 cal. looked like it had been dragged through coarse gravel for hours. It reloaded okay after being tumbled for several hours. The worse case scenario is from 40 Cal. shot in a Glock... big-time bulges at the base. A bulge buster fixes that problem though and I reload only once if it's from a Glock. BTW, the primers don't appear to be a problem, IMO.
I've been watching this Shooting Impressions multiple times because this pistol really peaked my interest. I held one at a local gun shop this afternoon for the first time. And imo, the trigger felt very nice to me? I'm really thinking you might have a real "lemon" model there.. especially with your barrel issues as well?? Maybe??
I reload everything I shoot. Regarding the round(s) that did not allow the gun to fully go into battery; do you guys use your barrel to check round fitment _before_ you shoot? I ALWAYS do. Of the brands of gun I have, I've found my Taurus's to be the most sensitive to bullet seating height; if remove the bbl press the round in with my thumb, then turn the bbl upside down -- that round should readily fall out, or the bullet is not seated properly, IMHO. Regardless of what ammo I use, for defensive purposes, I would _ALWAYS_ use the above test!
A chamber fitment check is a part of every GBGuns tabletop video, and yes, this barrel failed. Taurus replaced this barrel under warranty, and we later upgraded to a Lakeline barrel.
I'm thinking that if the chamber isn't right bullets are being pushed into the case a bit during chambering, causing higher pressures. We have been in touch with Taurus and they are sending a new barrel. I've noticed in other reviews that other barrels were marked differently with "GX1", "GX0" etc. Ours is marked "GX3".
I’ve had my GX4 since FEB and only thing I’ve done is put some BIG DOT sights on it. Guns been great so far with 1000 rounds of 124gr . Only issue is I shoot low with this gun . Must be the size along with my huge mitts .
I also shoot a little low with mine. I changed to the larger back strap, but have yet to test it out. I’m 6’2, so same problem… I’m thinking that the thicker back strap is gonna help.
What do you think about all the Lakeline, LLC upgrades to the striker assembly and the stainless steel guide rod? I feel that after doing that, the trigger is smoother.
I've been tempted to buy one. Unfortunately the only media samples have gone to the "for rent" channels. When I see that I tend to think there's a reason they need to pay people. That makes me hesitant to purchase.
It appears we simply got a bad barrel. We have a new barrel in that has a MUCH better chamber fit. We'll do another video with it when we get the chance.
It's a great gun. We had some barrel issues with our early-production model, but Taurus took care of it under warranty. We have more videos on it. Welcome to the channel!
@@GBGuns thanks. Hopefully get a chance to shoot it in the next few days. That large backstrap does make a difference. Even with my pinky dangling, it felt better in my hand than some other micro 9's
Often imitated, but never duplicated... you know what they say, imitation is the biggest form of flattery. You've had me thinking since the table top review, and pointing out two things... the chamber being too shallow vs. unsupported, and the GX3 engraved on the barrel. I am of the opinion that barrel is weirdly liken to a .380ACP barrel, and now with the hard primer strikes... leads me to believe the back of the cartridge is too close to the breech face because the of the shallow chamber. Is it possible... in some odd way you've got a GX4, with a GX3 barrel that should've gone into a future production of a .380ACP micro pistol? Thanks for the usual 'What's For Dinner'™ tests... Tube On! EDIT: Just saw the additional footage at the end regarding the magazines... that IS just another concern to add to my initial thoughts above.
My theory is that the lead was too shallow, the force of clambering was seating bullets deeper in the case resulting in over pressure as we saw evidence of in the form of primer flow. The new barrel arrived today. We'll do a retest soon.
The marking on the barrel is probably a forging machine number. That way if you get a bunch of barrels outta spec you can quickly locate the bad machine and take action. The barrels are definitely not for some future .380 micro gun
It's honestly really nice to shoot. Very manageable recoil despite the smaller size and the grip cushioned a lot of the vibration one sometimes feels in these little guns.
Where the brass is supported there's a small divot in the firing pin hole and that whole a divot to keep and dirt from getting in there because Taurus says it's a normal carry in the pocket pistol and they're afraid the lent and dirt may get in there and stop the firing pin.
Yes, but we also had a chamber fitment issue with our barrel. Taurus replaced the barrel under warranty and all is good now (we have another video explaining that and showing the difference)
bought this baby bout 4 months ago. never had chance to take it 4 a ride just yet. bout to disassemble and lube him up (lol). then I'll feel much more comfortable for every day carry.
Primers look OK slight amount of issues I've ran 100s of reloads in my gx4 toro before I even seen this video if you watch your load data you won't have a problem if you double charge your load your gonna have issues with any manufacturers brand good video tho thanks...with the ppu case I'd reload it again but I'd watch it carefully and I wouldn't load it hot I never seen that before with any brass but I will be looking for that now I think the taurus gx4s trigger is great but then again I like the factory glock slim lines triggers also that everyone hates on
Meh, not anything impressive, and sometimes you really do get what you pay for. Plus my carry Ammo would endanger my life fired through this handgun. Graham do you plan on getting your hands on a Ruger Max-9 or a S&W Shield Plus? It's okay if you don't plan on it. Honestly I can't keep up with all the new releases myself 😳💸 All that aside, great review as always!
@@Kratos_God_of_50_BMG FYI, most reviews that compare this and the Max-9 have noted the GX4 feels far more solid, just better built and has shot better as well. The Max-9 wouldn’t be on my short list. The Plus…..maybe. But the grip is like coarse sandpaper and that’s not a comfortable feel for me. YMMV.
Thank you and welcome to the channel! Most of our videos are part of articles, check for pinned comments (some of them have pricing and where to find stuff).
You said there was no trigger “pull”, with this gun. That’s actually one of things that I like about it. Very little travel, distinct wall, and crisp break. No “mush”. Also, the reset is very short. All pluses, in my book…
It certainly makes for a more pleasant shooting experience. We describe and explain our experiences and leave it up to you if that's something you want or not.
@@GBGuns I really enjoyed that review. Thanks guys. I actually already own the GX4, and I absolutely love it, for a carry gun.
We have been in contact with Taurus are are going to try another barrel. The more we shoot this the more likely it seems the chamber is out of spec. Stay tuned for a follow up video with a new barrel. Article: www.gbgunsdepot.com/post/taurus-gx4-enters-the-micro-compact-game
thanks for the input . will have to wait if they changed or made a new barrel . that happened with the tx22 .
Not being in spec was found with a replacement Taurus G3C barrel from Lakeland! This was a Fan Boy for Taurus who had sent for another barrel for his factory provided barrel! This had proved to be not Lakeland but a Taurus not cut to spec! They were able to get another to fit the slide!
thanks for the info!
I waited 4 months for a repair on the TX22, which turned out being a barrel replacement. Done with Taurus...
@@cantputt3378 with a completely new barrel or a replacement?
Long time handgun reloader here. Almost 40 years.
The primer flow is a non-issue as far as reloading goes. The hole in the slide for the firing pin is larger than it needs to be and you get a little flow. As long as you stay within spec you'll be fine. If I saw that on a magnum revolver with lighter loads I would have a problem; but not in 9x19.
The smile is less pronounced than a 40 Glock, or even an early 9mm Glock. Not a problem as long as you don't use the case for multiple really hot handloads. Again, almost no one reloads hot 9mm unless they are "making major" in a match gun, which certainly doesn't apply here. I haven't seen a case fail from smiley until the fourth or so hot load. You can see it progressing, so just watch your brass.
The smoke ring is usually low pressure loads. An oversized chamber will do it too, which is common in defensive guns.
The failure to return to battery is likely just debris of some sort; dirty gun, what have you. The one round that never chambered is obviously out of spec and doesn't reflect on the gun.
Hopefully the new barrel fixes what ails this. And try the Arex Delta Gen 2; in this climate you can always sell a gun for list price.
I really appreciate your insight, it's been years since I've reloaded and find it quite fascinating
Thank you for the information! I want a subcompact delta if they ever make one.
@@11spitdms They can't import one do to the point system for handguns. But since the gun is modular they can sell micro grip modules and smaller slide assemblies. Look for them to do that when/if they get enough "base" models sold that they think they can turn a good number of conversions kits.
Very few comments on UA-cam altogether are that informative and right-sized. Bravo.
A defensive handgun should emphasize function over most other things
Long time shooting enthusiasts especially love shooting Pocket guns and Micro 9mms. Never owned a Taurus. However, after testing this gun with others at my club, I was a instant fanboy. Man I love this gun. IMO the very best Micro 9mm money can buy. I was shocked at the quality and shooting control. My new one now has over 700 rds of every thing I could find to put into it and not one single issue. NONE. Just recently bought the Toro Slide to go with it for only $149.00.
Taurus obviously went into the competitive market to come out on TOP and that they did. They took the best of all the Micro's and put into this gun. Love the Trigger for EDC. What a unique design. I would not be surprised to see others try and copy it. I was not looking for a Budget gun and I did not get one, What I did get was a top quality gun at a budget price. I would have paid much more if that had been the cost.
@john burns is the gx4 snappy i want to replace my ruger ec9s for a better feel and shoot and capacity
Just picked up a GX4 after watching multiple reviews including yours. Took it to the range today for the first time after the initial field strip and lube and put 160 rounds on steel, including Federal AE 115gr FMJ, Remington UMC 124gr FMJ, Winchester WB 147gr Flat Nose and Fiocchi 115gr JHP. NO failures of any kind. The trigger was very good, perhaps a little grittiness in the initial take up, but after reaching the wall it broke crisply at my guess of about 5 lbs with minimal over travel. Reset was very short and tactile. The slide release was easy to manipulate during reloads unlike a lot of micros that are very stiff. POA/POI were right on once I figured out the sights seem to be regulated for a "combat" hold. I am by no means a marksman and despite my shaky old man hands I had no trouble hitting a 8" plate at 15 yards.
After your discussion in the video about the primer blowout and "smiley face" marks on the brass, I checked several of my spent cases and they showed the same although the smileys were less visible than the one's you had. To the naked eye I didn't seen any bulging on any of the cases.
All in all I am very impressed with the GX4. For me personally I find it fits me better, is easier to shoot well, and recoils less than my Kimber Micro 9 and carries 4 more rounds. I have ordered two of the pinky extensions from Taurus to get the full 3 finger grip (I only get 2 1/2 with the 11 round mag with the flat base plate) and am considering replacing the front sight with a fiber optic or painting it green or orange to make it easier to see.
I had my choice narrowed down to the GX4 and the CZ P-10S. The CZ is a fine pistol in every respect and it was a toss up between the two but I went with the GX4 due its' slightly easier to conceal footprint. Maybe for Fathers Day I'll get myself the CZ!!
Thank you both for a very thorough and informative review! Love the balance that two people can provide. Also thanks for your contribution and sacrifices made for our great nation.
Great to see a big variety of what's for dinner. Hopefully a sign of better days coming in ammunition supplies.
I hope so too. Sadly this was just supply we've held on to since 2019. We have 40 or so loads we rotate through, shooting just 3 at a time plus the lack of new guns recently has helped us milk the WFD supply.
Kudos to your more in depth review of this handgun. Your lovely shooting companion wasn't keen on the guns trigger but her shooting accuracy was impressive. Excellent review.👍
Thank you. I've learned that over time trigger drag improves and we did notice that the more we shot it the easier it became. Knowing a gun well is crucial in self defense.
Thanks Graham.
I'm glad things turned out well, and there were no injuries. I know that some of the companies reduce chamber support to increase reliability. But if you do like Sign with the P365XL and split the difference between the feed ramp and the ejection side, you won't get the smile. The G3 is so well supported, that a wide mouthed HP bullet (also Lehigh XD, XP) will NOT chamber from a full mag for me.
I definitely would not reload any casings from a gun that does not have a truly supported chamber. Primer hole is too big on that gun, Graham, that's why the primer is flowing back.
I waited to buy the P365 and its now a trusted EDC after they fixed the initial issues. I think I'll wait to buy this one as well.
Another great and trusted review by the two of you with things pointed out that others had not. Thank you. 🙂
Took my GX4 out to the range, and found that once I felt comfortable with my hold and sight picture, accuracy at 15 yards was quite nice -- easily a good CCW. I had absolutely no malfunctions!
I tried it with both back-straps, and preferred the smaller one. The larger one was a tad too large and the smaller one a tad too small. I used 124 gr ammo. IF Hogue comes out with a new grip that will stretch over the smaller backstrap, I bet it'll be the best of the three worlds.
Use a piece of bicycle inner tube.
I bought the Taurus G3. Glad I did. I love my Springfeild Armory Hellcat the best. You both are wonderful and very honest about what you review. Outstanding to all of us viewers to get truth and not media biased bologna.
I own a GX4 & a GX4 XL TORO
I break in my 9mm pistols with 124gr ammo .. and I have ran lots of ammo through both of them
Zero malfunctions …. These little pistols are not finicky
Great pistols
Your channel is one of the best on here. I always want to know your opinion before i buy a new gun. 'That is if you have reviewed it"
Thank you. I wish we could cover them all!
Some of us prefer our pinky to dangle. Especially after my last motorcycle crash.
I got a taurus g3c...last month...shoots well handles very well "GODD JOB" TARUS ON THE G SERIES...
You mentioned an extremely important thing that nobody else talks about. Ballistics. 9mm from a 4” barrel is one thing. Once you go to 3.5” (G26)things change and 147gr HP’s don’t always reliably expand, in my experience. I carry a 43x, 3.4” barrel, and that’s right on the line. 3.0”-3.1” are going to be a crap shoot. I wish people would do gel tests with the micros. I’m sure a 115gr-124gr +p would open up but probably not through all test mediums. Thank you for bringing this up.
It's a serious point. There are some great modern specialty loads designed to perform well at the lower speeds these shorties create, but they still don't deliver the energy that a longer barrel does. I personally don't carry less than a 4". I want my HPs to open and I want as much energy dumped into the target as possible.
Well explained vid, nice way to test a gun with different ammunition, long story short... im subscribing to the channel. Love this content. Good job!
Thank you and welcome to the channel! We test every gun in this format so you have a better idea of what you're getting into. More in depth than "it's a good or bad gun" descriptions without any scientific process to back up that conclusion.
Mine broke after 230 rounds. Sear snapped in half. Taurus charged me 50 to ship it for repair. Only gun company not paying for postage on warranty items. I've purchased 3 Taurus pistols and all 3 broke early on. They work great until failure. Then how do you trust for carry? Waste of money. Save up and buy something else. I bought a canik sc.....awesome.built like a tank.
How do you like the Canik SC ? I want one . I bought the GX4 due to wanting something smaller for summer carry but been very intrigued by the Canik SC
It is bad that you have had such a bad experience with Taurus. Just my experience. I have bought close to 40 Taurus handguns and never had any issues but one. I bought 4 spectrum 380's and only one of the 4 was finecky with the ammo. I have revolvers, 9mm, 22, and 380's. I love Taurus. I also own P365, Hellcat, M&P 2.0. I love them all.
Good info. I will be shooting the GX4 tomorrow for my review, so I'll watch for the brass/chamber issues.
My TX22 had a nice scratch across the slide. Sights off a bit too! Thanks for the share!!
About to buy this tomorrow
I agree about the larger backstrap. Fixed my problems with GX4.
I've never had an issue with steel - Tula or Wolf in my Glock43, Beretta APX, as well as the Taurus G2C. Glad to see they work well in the Taurus GX4. The current deal with BudsGunShop of $209 after the $50 Taurus rebate make this a win-win in my book. Waiting on arrival now.
Great review and excellent presentation. Thanks for pointing out your observations regarding the casings, the barrel configuration, and variety of barrels. Thank you both for all you do. 🎩☯️♠️
I am a reloader and my initial thoughts are NO WAY would I shoot reloads out of this firearm. The lack of chamber support and blow back of the gasses are not safe in my opinion. This will not be a likely purchase for me or mine. Thanks you two for another great review.
If you wait until Taurus works out their QC problems, design flaws, and mandatory safety recalls before buying the G4, there will be a G5 coming out.
😂😂😂
Seriously though!
Lucky my experience has been hit n miss I don’t own anything Taurus 🤷♂️
Today @ about 1600 rounds my firing pin broke in the GX4. I noticed the firing pin drag on the struck primers when I fired my first shots and knew that was common on micro-compacts as firing pins were breaking but it wasn't a huge concern. Firing pins are cheap right? I have broken them in Glocks. This is the first Taurus I have owned in 33 years and only revolvers. Now, getting off the phone with Taurus and finding out they won't sell me a firing pin, I have to send them the gun, and it cost a lot to ship it that's not covered by the warranty, and it will take 4 to 8 weeks. Just to take two minutes to remove the back plate and change the firing pin assembly. It makes me realize I wasted my money buying a Taurus. I'm sticking with Glocks and Sigs. I can buy spare parts for those.
Just Ordered Mines Yesterday And It Shipped Out Today, Can't Wait Till It Arrives...Best Deal On The Market
The algorithm opened with the ad, “BEEF. It’s what’s for dinner.” 🤣🤣🤣
Excellent Review! Brass with a slight bulge at the belt like that should not be reloaded and will require more effort to resize. Case life will be shortened considerably and could cause a blowout. Not worth the effort to reload! Firing Pin hole in the Slide boltface is too large allowing the Primer metal to flow back.
I have other Taurus Pistols with which I am pleased with, but I doubt I would buy a GX4. I often carry a 9mm Taurus Millennium Pro or a Canik TP9V1.
I went ahead and purchased one for close to MSRP and I am looking forward to shooting it. You mentioned in your shooting impressions video that the GX4 down not feel like a budget gun, it doesn't shoot like a budget gun and that is one of the reasons I bought it. I've enjoyed owing Taurus handguns through the years specifically the G2C, TX22 and the Beretta clone 92.
I realize this is 2 yrs old but i love the format and team yall got.
This is a Great Carry Gun, no Matter What Your Budget is.
I have a pt111G2, a G3 and. G3X. As a big guy my favorite is the G3X for the 15+1 capacity and decent trigger. I’m thinking of going with the GX4 Carry as all the tests I’ve seen seem to point to the GX4 strengths and adding the 15 round capacity and accessory rail as on the G2 and 3. All the testers comment on the less barrel flip than comparable models and as you watch the videos it seems that it recoils straight back which may be due to the barrel being closer to the grip. Great review. It helps seeing a women give her take as often men don’t have the same likes and dislikes.
Good review.
I'll stick with the G3C.
I like the restrike capability of the G3C & this gun is new and has no long term history yet.
The cartridge burn concerns me.
Not just Taurus, but a lot of guns get produced before they have been thoroughly tested and developed.
I have put 4 people 6 feet under so far with my gx4. It works. Stop being an overthinking Suzie.
Picked one up today
I went with the ruger. All my guns are range guns. I shoot them all equally.
That's the one that I would like Graham to review, but we can't buy all of them now. I do have this extra kidney laying around here......
If you look at the firing pin hole on the breach face you will notice an oblong chamfer with the largest part pointed down. This 'primer flow' look is caused by the shape of it. I'm not a fan of the unsupported chamber. I don't think these things will be a problem but only time will tell now that the pistol has been released.
We've been in touch with Taurus. The replaced our barrel. We will retest with the new barrel. If you look at our Tabletop video you can see the chamber fitment was off to being with. My guess is a short lead causing the projectile to be seated deeper by the force of chambering and resulting in slight over pressure.
@@GBGuns primer flow thing is just the shape of the firing pin hole. I get the same thing. Did you get the new barrel and did anything change?
Thats all in the update video
Great video now I really appreciate your information and more excited to take my gx4 to the range 😀
We have a third video after this one with updates on the barrel.
My new gx4 jams like a rock band.Shot many brands about 800 rounds and jammed on all outings.Shot great when it fired.Also got trigger finger pinch.Back to taurus it goes
Let us know if they fix it.
Always enjoy your videos and I look forward to the follow up when the new barrel comes in.
I bought mine same day I also bought a Hellcat Pro and was surprised it printed tighter groups than the Pro. Better trigger and grip angle so looking forward to also getting a Gx4 Carry.
Great team assessment.
Ok, now I've bought a new Taurus GX4 Micro Carry. My primers look just like yours, being my reloads or factory loaded ammo. If you look at the firing pin hole, you'll notice that it isn't round, but has some relief cut below the hole itself. Taurus says it's to help with any debris that may get in that area to fall out. It seems that they all have that relief cut in them, so your primers are actually normal, for a Taurus anyway. It also makes it look like you are getting light primer strikes, (Which I have had a few of), when you're not, because it also allows the dent in the primer to blow back out somewhat. I learned that my light strikes were due to primers not seated deep enough into the primer pocket. When you're loading range brass you are loading many different brands and makers of brass, and they are not all the same. In some cases, the primer actually seats below level with the head of the case. If that is done, it will fire them every time. You want to use a small primer ram to reload for this pistol so it can push the primers all the way to the seated position and if you do that it will be one hundred percent reliable. As far as your (Smiles), I've not noticed that, even with very hot loads. What I've found with my used G2C and the new GX4 is they are one hundred percent reliable.
Taurus confirmed this was a bad barrel and replaced it under warranty. We have a follow up video on that.
Just a thought about the ammo. I have had some of the same issues with 22lr. It's like the manufacturers have had to loosen the specs a bit to produce more ammo. They can sure sell it.
Nice pistol love mines, I got the 13rd mag but plan to order 2 pinky extensions soon
Impressive review and extremely helpful. I purchased my GX4 yesterday and I prefer a small gun for a conceal carry/defensive situation because my hand fits better; however, I will try the bigger backstrap. Unfortunately, when I brought the gun home and went to load one of the magazines, it was defective, and I cannot even get one bullet into the magazine. I pray Taurus has improved their customer service from the first time I tried contacting them a few years ago about my Taurus G2.
Let us know how the experience goes
@@GBGuns I was elated they answered the telephone and Taurus is sending me a new replacement magazine.
@@GiselleMarieXIII That's great. I've heard things have improved. We had issues with this gun at first (we now have four videos on it) but Taurus took care of things quickly, and much better than my customer experience with them back in 2015.
I am an Avid reloader and was really thinking about buying this pistol. Had never seen a video before yours point out the chamber problem. (not being fully supported). One reason I'm not a big Glock fan. I own a G2C and for some reason I've never noticed a problem with guppy bellying with it at all. Maybe they changed their chamber dimensions on this one. But then they talk about the G2C having such a crappy trigger and I have no problem whatsoever with mine. No worse than any Glock I've ever shot anyway. And I own two Glocks.
Taurus sent us a new barrel under warranty after this video. We have a follow up videos with the replacement barrel.
I would absolutely reload that brass. Of it was more of a crack I’d say no way but for 9mm I would reload
I place the GX4 ahead of several "top tier" edc pistols (Glock 43x, SIG 365, Hellcat (not Pro) and MC9). I found it be a little snappy, but nothing like the 365 or Hellcat. I'm just more accurate with it than the Glock. The MC9 I just don't care for... More to do with ergonomics for me. I saw that they released an extended mag, that actually comes all the way back under the rear of the backstrap. That may change my mind on it somewhat, because the MC9 does have a really good trigger.
Thank you for this honest review I love watching all your videos
Thank you. We do have follow-up videos on this gun. It turned out to indeed be a bad barrel which Taurus replaced under warranty.
I just bought the GX4 and took it out to the range for the first time yesterday and shot it side by side with my Sig P365. I actually found that the Taurus fits my (medium) size hands better than the Sig, and with the Sig using my normal grip my support hand thumb always seems to be resting on the take down lever. You guys made this video a year ago and I'm wondering if Taurus has since made some adjustments to the trigger. My personal experience in my 200 round range session yesterday was absolutely outstanding, and I was able to shoot the GX4 more accurately than my P365 and lower recoil impulse. I did also notice the slightly bulged primers and the burn marks on one side of the spent shell casing, but I see the burn marks on several of my Glock casings too. I didn't have any issues of the pistol going into battery but wasn't shooting the same ammo as you guys. Great informative video guys! Nicely done and nice shooting!
Taurus may have made some changes. They also replaced our bad barrel, we have follow up videos with the bew barrel.
@GBGuns thanks! I was just watching your table top review the on the cartridge not being fully supported. I learned something new there, thank you!
great review thnx
We have a follow up about the barrel
Interesting you guys are the only ones that pointed out the anomalies on the brass and primers, and probably the only ones that fussed about the trigger pretty much everybody else really liked the trigger I guess a lot of it boils down to personal preference or what you really like.
Oh good, the shooting impressions. Shame about the pin, hopefully it really is just this barrel.
This is all i need to see , besides the unsupported chamber it looks like a good gun.
I'm thinking that if the chamber isn't right on our barrel and bullets are being pushed into the case a bit during chambering, causing higher pressures. We have been in touch with Taurus and they are sending a new barrel. I've noticed in other reviews that other barrels were marked differently with "GX1", "GX0" etc. Ours is marked "GX3".
@@GBGuns I didnt know that , mix up of barrels and i hope they send you the right barrel.
@@user-jetmachinist I don't think it's a mix up so much as there were different barrels made. That or the "media guns" we see out there had an earlier barrel design. I've seen some people say the "GX3" marking on our barrel is because it's a GX series gun, 3" barrel, but that doesn't explain why there are 3" barrels marked "GX1".
@@GBGuns That is interesting to know , i hope the riddle will be solve.
@@GBGuns the most plausible guess I read is it’s a milling machine number. If that’s the case and you get a bunch of barrels that fail QC you can quickly identify the out of spec machine by number and either repair it or take it out of service to repair it
Nice review 👌 👏 👍
There is a follow-up video after the barrel was replaced under warranty.
I was the 1000th like! Woohoo! It's the little things. Great review! This is looking like the bang for your buck in the micro 9 department.
Thank you, and it's an excellent pistol. The issues we experienced were resolved with a barrel swap under warranty.
Ofcourse it will run without issue ,thats how good TAURUS designs these days!
Never heard anyone more concerned about their pinky. You actually don’t need your pinky to shoot.
Nice gun
I've reloaded 10's of thousands of rounds of 9mm. As long as you resize the cases there should be no issues. The leaking gas around the case will effect your velocity and even aim as the bullet may drop more as a result of lose of pressure around the casing, however this is very common with many small cal. auto guns. The primer flow is due to poor fit between the firing pin and hole bolt or slider and should be corrected in future by manufacture. No need for concern as long as there is no hole in primer after firing it. If you find a hole in primer be sure to have it repaired ASAP.
Our barrel was faulty and replaced under warranty, we have follow up videos on this.
I an a reloader and I have experienced a lot worse cases, but from a Hi-Point. Brass from a 40 cal. looked like it had been dragged through coarse gravel for hours. It reloaded okay after being tumbled for several hours. The worse case scenario is from 40 Cal. shot in a Glock... big-time bulges at the base. A bulge buster fixes that problem though and I reload only once if it's from a Glock. BTW, the primers don't appear to be a problem, IMO.
Thanks. Taurus replaced this barrel, you can see the difference in our follow up video
I've been watching this Shooting Impressions multiple times because this pistol really peaked my interest. I held one at a local gun shop this afternoon for the first time. And imo, the trigger felt very nice to me? I'm really thinking you might have a real "lemon" model there.. especially with your barrel issues as well?? Maybe??
We have a replacement barrel and will retest.
@@GBGuns Yes, I read that. Looking forward to the update. Thanks
I reload everything I shoot.
Regarding the round(s) that did not allow the gun to fully go into battery; do you guys use your barrel to check round fitment _before_ you shoot? I ALWAYS do. Of the brands of gun I have, I've found my Taurus's to be the most sensitive to bullet seating height; if remove the bbl press the round in with my thumb, then turn the bbl upside down -- that round should readily fall out, or the bullet is not seated properly, IMHO. Regardless of what ammo I use, for defensive purposes, I would _ALWAYS_ use the above test!
A chamber fitment check is a part of every GBGuns tabletop video, and yes, this barrel failed. Taurus replaced this barrel under warranty, and we later upgraded to a Lakeline barrel.
Look at the 2022 los lunas bug scores on practiscore. 5th place was won using this gun. With handloads...
❤ that syntech defense! 😁👍
All the things!
The spinner test should be called What's for Spinner
Thanks GB. Great job. Good info.
The primer flow issue might be striker drag or the flash hole might be a wee bit too large for the diameter of the striker.
I'm thinking that if the chamber isn't right bullets are being pushed into the case a bit during chambering, causing higher pressures. We have been in touch with Taurus and they are sending a new barrel. I've noticed in other reviews that other barrels were marked differently with "GX1", "GX0" etc. Ours is marked "GX3".
This is the second video I've seen these guns having jamming issues
The gun is not trash.
@Your Daddy you said, "trash operator" which is someone who operates trash.
Your ignorance is astounding, but you have internet access so there is hope.
@Your Daddy There were no valid points to debate. Had you accused us of being aliens i wouldn't have bothered with that either.
You tell me. Thabks for the boost against the algorithm though. Your mindless comments still count.
I’ve had my GX4 since FEB and only thing I’ve done is put some BIG DOT sights on it. Guns been great so far with 1000 rounds of 124gr . Only issue is I shoot low with this gun . Must be the size along with my huge mitts .
I also shoot a little low with mine. I changed to the larger back strap, but have yet to test it out. I’m 6’2, so same problem… I’m thinking that the thicker back strap is gonna help.
What do you think about all the Lakeline, LLC upgrades to the striker assembly and the stainless steel guide rod? I feel that after doing that, the trigger is smoother.
We've tried the ported barrel. Lakeline makes good stuff, we've been a supporter of their for years.
@@GBGuns thanks for the answer.
we would like to see arex delta gen 2 pistol, seems like an great all-around and affordable option
I've been tempted to buy one. Unfortunately the only media samples have gone to the "for rent" channels. When I see that I tend to think there's a reason they need to pay people. That makes me hesitant to purchase.
Think I'll let Taurus work on this issue before I think about picking this one up
It appears we simply got a bad barrel. We have a new barrel in that has a MUCH better chamber fit. We'll do another video with it when we get the chance.
Good job. I like your test criteria.
Thanks you, we've reviewed dozens of guns in this format.
The trigger not having any adjustment and be able to adjust your shot is the exact point of the trigger.
very thorough review, thanks!!
We have followed up videos too after getting the replacement barrel.
New sub here. Just picked up the gx4 because I needed something for bike rides/family walks/around the house/in the yard etc.
It's a great gun. We had some barrel issues with our early-production model, but Taurus took care of it under warranty. We have more videos on it. Welcome to the channel!
@@GBGuns thanks. Hopefully get a chance to shoot it in the next few days. That large backstrap does make a difference. Even with my pinky dangling, it felt better in my hand than some other micro 9's
Often imitated, but never duplicated... you know what they say, imitation is the biggest form of flattery. You've had me thinking since the table top review, and pointing out two things... the chamber being too shallow vs. unsupported, and the GX3 engraved on the barrel. I am of the opinion that barrel is weirdly liken to a .380ACP barrel, and now with the hard primer strikes... leads me to believe the back of the cartridge is too close to the breech face because the of the shallow chamber. Is it possible... in some odd way you've got a GX4, with a GX3 barrel that should've gone into a future production of a .380ACP micro pistol? Thanks for the usual 'What's For Dinner'™ tests... Tube On!
EDIT: Just saw the additional footage at the end regarding the magazines... that IS just another concern to add to my initial thoughts above.
My theory is that the lead was too shallow, the force of clambering was seating bullets deeper in the case resulting in over pressure as we saw evidence of in the form of primer flow. The new barrel arrived today. We'll do a retest soon.
The marking on the barrel is probably a forging machine number. That way if you get a bunch of barrels outta spec you can quickly locate the bad machine and take action. The barrels are definitely not for some future .380 micro gun
What’s for dinner, followed by what’s for spinner. 🙂
How does it shoot compared to the Taurus G3C or others in this class? Thought about getting the G4, G3C or SCCY DVG if it ever comes out.
I was impressed with the $275 g3c but i want this one too
It's honestly really nice to shoot. Very manageable recoil despite the smaller size and the grip cushioned a lot of the vibration one sometimes feels in these little guns.
Where the brass is supported there's a small divot in the firing pin hole and that whole a divot to keep and dirt from getting in there because Taurus says it's a normal carry in the pocket pistol and they're afraid the lent and dirt may get in there and stop the firing pin.
Yes, but we also had a chamber fitment issue with our barrel. Taurus replaced the barrel under warranty and all is good now (we have another video explaining that and showing the difference)
Great informative review. 500 rounds and no issue. However, I do use the same ammo. Maybe that's the key?
bought this baby bout 4 months ago. never had chance to take it 4 a ride just yet.
bout to disassemble and lube him up (lol). then I'll feel much more comfortable for every day carry.
I wonder how much the xl model would change if any these tests?
Hey Graham, try crossing your pinkies next time.
Primers look OK slight amount of issues I've ran 100s of reloads in my gx4 toro before I even seen this video if you watch your load data you won't have a problem if you double charge your load your gonna have issues with any manufacturers brand good video tho thanks...with the ppu case I'd reload it again but I'd watch it carefully and I wouldn't load it hot I never seen that before with any brass but I will be looking for that now I think the taurus gx4s trigger is great but then again I like the factory glock slim lines triggers also that everyone hates on
I hate Taurus but think i might have to give the gx4 a try.
Train till the brain forgets and the body remembers will solve
the issue with trigger.
Picked up my new GX4 yesterday and wondering what specific 9mm ammo to use when breaking in the gun....don't want to use my critical defense rounds.
Any 9mm will do
32:45 my 365xl does the same thing
Wait, did she just say "BBC sized"??🤣🤣 I was driving and wanted to make sure I heard that right .
B6C
@@GBGuns 🤣🤣🤣 I laughed so hard either way. I thought I heard "BBC sized".
Meh, not anything impressive, and sometimes you really do get what you pay for. Plus my carry Ammo would endanger my life fired through this handgun. Graham do you plan on getting your hands on a Ruger Max-9 or a S&W Shield Plus? It's okay if you don't plan on it. Honestly I can't keep up with all the new releases myself 😳💸 All that aside, great review as always!
Thanks. We might to the S&W, won't do Ruger.
@@GBGuns Oh right, right, I forgot about your beef with Ruger. My bad!
@@GBGuns Er, uh, why not? Inquiring minds want to know!.......................elsullo
Nothing with their products, just the way they've interacted with me in the past. It's personal.
@@Kratos_God_of_50_BMG FYI, most reviews that compare this and the Max-9 have noted the GX4 feels far more solid, just better built and has shot better as well. The Max-9 wouldn’t be on my short list. The Plus…..maybe. But the grip is like coarse sandpaper and that’s not a comfortable feel for me. YMMV.
hi! is that something taurus will have to fix by changing the barrel so it will support the case of the ammo??
We may have had a bad barrel, Taurus is replacing it
How does this trigger compare to the Canik Mc9 trigger?
Pages 9 &10 of the operator's manual states Do NOT use +P Ammo in this pistol. Warn your viewers please.
My manual says it's ok.
I'm not expert but my manual says +P is okay, but not +P+
New subscriber here, looking to buy a gx4. Liked your review! P.s. I'd hate to have Tia shooting at me!
Thank you and welcome to the channel! Most of our videos are part of articles, check for pinned comments (some of them have pricing and where to find stuff).