Fiat Punto 188 Power Steering Motor repair

this is a common problem on Punto from 1999 up to 2004
these relays are a known failure in these cars

[@DoNaSbaR]

13:30 The 4117-U-Z relay is equivalent to V23072-C1061-A308. Nowadays it is very difficult to find the original for sale. Thanks for the video.

[@M3PowerCZ]

Thank you for the instructions. Today I successfully repaired my wife's Fiat Punto!

[@PSICompanyPerformance]

Thanks for watching.
Glad to help my friend.

[@davorbabic8720]

Thanks you for sharing! After 3 years of heavy turning my Puntos steering is like in Mercedes :)

[@gaelb.6035]

Thank you for sharing, it's very precious and I see you work very well, congrats 👏🫡

[@dookieday1]

Great video ,I will reference from this when I do mine ,it's playing up lately..

[@PSICompanyPerformance]

Thanks for watching.
Go for it this the most common problem with these.
Good luck

[@Alan-mg1rp]

Hello where can i get the relays from i have a mk2 2005 punto 1.2 in UK.... it work ok then stops working then works again I think its time to get it fixed... great video easy to follow...

[@x-men6367]

Very good 👍👍👏👏

[@rafiekahmed8568]

Hi thanks for sharing I was wondering if the if motor have brushes if have Alfa mito and the power steering gets hard from time to time while driving I replaced the relays but I’m still the same problem
Thanks in advance

[@PSICompanyPerformance]

Thanks for watching.
No these motor are brushless...you can have a rare case of the module under the steering column failling.
Good luck..
Also make sure your battery is in good condition and the alternator too.

[@geaninamarculescu6776]

hello, these relays also work on fiat punto 2004 , 1.2 ? Thank you very much

[@PSICompanyPerformance]

thanks for watching.
2004 Punto i think uses a little diferent motor thyat has no relays on them....if thats the case the problem is going to be the control module located under the steering wheel.
good luck

[@ndia60]

On the road while driving, the steering wheel became very hard after I turned off the car, it was fixed but it did it again later fiat punto evo 2010

[@PSICompanyPerformance]

Thanks for watching...
In your case, your car does not have this motor...but i have a video in my channel about the steering angle sensor replace of a grande punto that is exactly like yours...
Good luck

[@tonykidd13]

Hi
Any ideas on a fiat punto mk2b 2004
Same issue, would it be easier to change the motor or is it a module??
Any help would be great 😊

[@PSICompanyPerformance]

Thanks for watching
In 2004 the motor is diferent and i never had an issue with those but i had issues with the module under the steering wheel..good luck

[@tonykidd13]

Thanks for the quick response, what is the module? Do you mean the steering ecu part? Sorry to ask
Best wishes 🙂

[@PSICompanyPerformance]

@@tonykidd13 yes that is exactly that

[@nic0lac]

I have a fiat punto 2002 , it’s the same ralay?

[@PSICompanyPerformance]

Thanks for watching
Well there are two types of electric motor, these or tge other type that doesnt have relays....so if yours has relays then these are the ones you need.
Goid luck

[@nic0lac]

@@PSICompanyPerformance thank you

[@dariopretorius984]

Hi
I have this problem with the steering light it only happend when i am driving after a while and in higher speeds when i stop turn car off and then back on it works again normal until it does it again
This is the relays correct?

[@PSICompanyPerformance]

What is the year of your car?

[@DailyWonders90]

From where I can buy these relays?

[@PSICompanyPerformance]

Thanks for watching...
I bought mine in a electronics store in my city...
But i have seen them on Amazon, Ebay and even on Aliexpress...
But if you want the original and probably better quality i would search for these in sites such as Farnell or Robert Mauser.

[@AbdurRahim-by9my]

Hey there. I was wondering, do you know what are the others reasons could be show red steering light on dash board . Because I tested the relay both are good. And sometimes my power steering works. Its means my motor are good. Is it or ? Anyways any information will be help. Thanks

[@PSICompanyPerformance]

Even when you test the relay some times when they get hot they fail..
Have you checked the solder points with a magnifying glass...its the most common issue.

[@AbdurRahim-by9my]

@@PSICompanyPerformance I did re soldering all the join, also checked if relay click with 12v. Its make the click noise , so I assume its good. Then I tried it. But unfortunately I didn't worked.

[@AbdurRahim-by9my]

Also can you please comment the relay reference. That will be great

[@PSICompanyPerformance]

@@AbdurRahim-by9my reference do you mean from the relay...its on the video...