DIY 6 Channels Radio Control For Models. How To Make İt

How to make 6 channels radio control. Diy arduino radio control for Rc models. Diy arduino rc receiver and transmitter.
Necessary materials:
2 x Arduino Nano
1 x NRF24L01 + PA Wireless Module
1 x NRF24L01 Wireless Module
2 x Arduino joystick
2 x 100uF Capacitor (16V or above)
1 x 13 * 6 cm PCB Board
1 x 5 * 3.5 cm PCB Board
Arduino Nano: www.banggood.com/custlink/vvG...
Arduino Nano & USB Cable: www.banggood.com/custlink/vDD...
RC Joysticks (No trim): bit.ly/3vIMd4l
NRF24L01 + PA Wireless Modul: www.banggood.com/custlink/33G...
PCB Boards:
www.banggood.com/custlink/v33...
www.banggood.com/custlink/3vG...
100uF Capacitor: www.banggood.com/custlink/DKD...
Headers:
www.banggood.com/custlink/m3v...
www.banggood.com/custlink/vG3...
680R Resistor: www.banggood.com/custlink/KKm...
5mm LED: www.banggood.com/custlink/vmK...
Rocker Switch : www.banggood.com/custlink/vDm...
5mm kraft foam board (50x70 plate): amzn.to/2oE2vOK
JST Connector: www.banggood.com/custlink/DDK...
Mini electrical cutting plier: www.banggood.com/custlink/D3m...
Arduino IDE Installation, Adding Library and Uploading Code : • Arduino IDE Installati...
Thanks for watching. If you want to support my channel, join.
/ @kendin-yap
CODE & SCHEMES: www.rcpano.net/2020/04/09/how...
OR tinyurl.com/47bweu64
Arduino IDE, library file setup and upload tutorial : • Arduino IDE Installati...
My Web Site (KendinYap): www.rcpano.net
All of my videos: bit.ly/2Z9QVYK
Thanks For Watching And Please don't Forget To Like, Share & Subscribe For More Awesome Videos.
KendinYap Channel / @kendin-yap

[@HasanAraycProjects]

Üstadım uzun bi zamandır yoktun emeğine sağlık söylemeye gerek yok yine muhteşem bi Video

[@nicolasmarti6725]

this is awesome ! much respect from a french guy living in japan, sir

[@thanhnamnguyen8888]

Can you give me code of arduino nano, please

[@PunakiviAddikti]

Basically with this setup, you're only limited by the number of input/output/analog pins on your arduino. You can send any data. It's a digital radio control system. Want 15 channels? You'll need 15 input pins and 15 output pins. But be aware that some joysticks use hall effect sensors. Those work differently than potentiometer based joysticks.

[@krulikonik]

You cannot use 15 channels fully, cause you need analog pins for joysticks.

[@Gifted_Gift]

please how can i make 15 channels?

[@PunakiviAddikti]

@@Gifted_Gift You'll need a microcontroller board with enough IO pins

[@AKElectroDIY]

Very simple, use an arduino mega board. It has 16 analog pins

[@JarppaGuru]

can it handle 15 channels or even 1024.
if you need buttons use parallers serial chips LOL
for remote 74LS165 (paraller in/serial out)you can use multiple input using ehh 3 wires?
for vehicle 74LS164 (serial in/paraller out)(74ls595) turn then back output
pins on ardnuino not any limit you can expand input and outputs but can this wireless thing handle more than 15. dont know LOL@@Gifted_Gift

[@francisaaronabadingo3902]

thank you again sir, for sharing this project.. I have tried it and very satisfied with the result..
I'm trying to add a battery monitor on the RX side back to TX -- but I'm still working on it, having a hard time on the codes.. I'll share with you the codes as soon it works.. wish me luck..

[@dontknow479]

I have li ion battery instead of lipo will that enough for transmitter and receiver! Please reply!

[@davydbar]

@@dontknow479 yes

[@shaunferris6063]

hello when you built this did you only use the 3 libraries he added or did you have to add anything else?

[@RohitKumar-wl5fw]

Bro tell me that it work or not

[@suchandrapaul5047]

Marvelous creation ! Very good job.

[@michelemarchese259]

Fantastic! Beautiful work!

[@basrikaragulle2933]

Kanalınızın hep bu kalitede devam etmesi dileği ile... tebrikler

[@eduardo33]

Maravilhoso o seu vídeo! Isso deveria ser um curso em escolas o que as crianças aprenderiam seria de imenso valor! Saudações do Brasil mais uma vez.

[@barskaan4014]

senin gibi kanallara ihtiyacımız var umarım hak ettiğin yerlere gelirsin

[@VENOMR9]

bu vidonun önce 2 vidyo işime yarar

[@vilsonandrade8191]

Very nice explanation. Even though as mechanical engineer, I could understand well. Congratulations from Brazil - Parana state - Araucaria city

[@anonymousbay7957]

bro it can not connect VCC pins thand how the every thing is working properly

[@nocomment_uzb]

Juda ajoyib. O‘zbekistondan salomlar.

[@wickedprotos1937]

Incredible work! Can't wait for the next video you mention. the code is so compact, wow.

[@user-dz3dw1wl4f]

Türkiye'nin böyle insanlara ihtiyacı var helal olsun üstad

[@profezor2]

Ohooo Türkiye de ne adamlar var, bu ne ki.

[@debashishdas4865]

Awesome bro.l was finding this type of video for very long time ago.Keep it up and you will get more students and subscriber

[@TheSayargyi]

I'm very poor in this technology, I've followed all steps and builded a receiver but I'm stuck to upload receiver codes. May I respectfully request you to guide me the basic way to upload the codes, please!

[@artmartdc]

I really enjoyed that and it has given me an incentive to make it!

[@purneshchandrayadav8419]

Amazing work. Really loved it ❤❤👌

[@Dragon69FlyTeam]

This is a great idea for my old broken robbe transmitter. eprom get wiped now i can use it again thanks

[@vdm7776]

Meraba!
Many thanks for your video and projects. Just, like a new idea, can you add a LCD screen for back feed with the model, such as a battery voltage and signal strength. And the selection of the model, if you will use two similar transmitters for several models at the same time?

[@shamalapawar4015]

Thanks for the video. Very good for something to make in Christmas

[@nikbivation]

this helps a lot, thank you!

[@masboyrc]

This is so cool !! Really nice idea. Greetings from indonesia 🇮🇩

[@aanandian8925]

sama wek

[@vitorbonis2632]

Parabéns ! Obrigado.... pelo vídeo e por descrever as peças de montagem.... Saudações do Brasil.....

[@dipanshudhote5671]

thanks man ur code really help me..............

[@michey7822]

Nice vid...will try building one too!

[@GustavoLima-jw1vo]

Meu amigo aqui e do Brasil, sou fan dos seus videos, parabéns pelo ótimo canal, ficou muito feliz que você sempre compartilhe com a comunidade os seus tutoriais que são um máximo 😎

[@Kendin-Yap]

Thank you.

[@calibermix8159]

@@Kendin-Yap what gimbals are you using ? the crap gimbals of the banggood link look totally different

[@huseyincan5495]

@@Kendin-Yap videodaki joystickleri bulamadım onlar yerine ne kullanmamızı önerirsiniz

[@warismwarism4300]

@@Kendin-Yap hey thx for this great video its realy informative , so can you plz explaine how we can use 433Mhz Module RF Émetteur + Récepteur

[@islamlechelah2793]

@@Kendin-Yap hey is there is any diff if I use RC Joysticks with 5k resistor?
like this :
www.aliexpress.com/item/1005001616807525.html?spm=a2g0o.detail.1000014.1.133f3ae4JBVZy0&gps-id=pcDetailBottomMoreOtherSeller&scm=1007.40000.326746.0&scm_id=1007.40000.326746.0&scm-url=1007.40000.326746.0&pvid=f9d48c80-abac-4aef-9a42-631366ed2d8a&_t=gps-id:pcDetailBottomMoreOtherSeller,scm-url:1007.40000.326746.0,pvid:f9d48c80-abac-4aef-9a42-631366ed2d8a,tpp_buckets:668%232846%238114%23762&pdp_ext_f=%7B%22sku_id%22%3A%2212000018004611774%22%2C%22sceneId%22%3A%2230050%22%7D&pdp_npi=3%40dis%21EUR%2111.42%2111.42%21%21%21%21%21%402101d1b216776937474897001ed7a3%2112000018004611774%21rec%21DZ%21

Üstad ellerine sağlık. Gerçekten güzel bir çalışma olmuş. Bir sonraki menzil testi videosunu merakla bekliyoruz. İmkanınız varsa bu sisteme birde fpv ekleseniz süper olur :))

[@sivambhai1971]

Shivam

[@RcModwerks23]

Awesome video! I like cool DIY videos like this ! Keep it up 👍

[@suleymandogan8205]

elinize emeginize sağlık . çok güzel görünüyor

[@moathnaji2763]

Salam friend
I like all your tutorials and your channel one of my favorites…
Could you make step up USB cable dc-dc booster 5v to 12v
with 1 amp or more. Please?

[@mcreativeworks9931]

VERY NICE AND I AM ALSO WORKING OF MAKING ON EOF THIS

[@Smartliving-udanagayan]

Wow very nice ..im really waiting for your next video..please upload it as soon as possible..I really appreciated your works..its amazing

[@sumonmondal5041]

Your every video is helpfull.Thanks.Go on.

[@ekojokosetyono5823]

thank you so much, Bro. it's very good for me to learn arduino.

[@GAMEmaster-ir8ge]

I need help

[@jithashaju4331]

​@@GAMEmaster-ir8ge😮

[@moviecinema7262]

Thank you so much for the code! It worked without any delays

[@antonisvianos8017]

Perfect Job and works very good.!!!!!!!!!

[@tomjoad1060]

Very nice work, Kendin Yap!

[@baddreams0919]

Now I know what i'm doing this summer vacations

[@xxxtrib]

did you do it?

[@animeepisodes6724]

Maynn, where do you keep all this talent?!?

[@topglobal6kagura27]

In your mom closet
JK XD

[@peterbogner1675]

Dear Kendin Yap,
i like your videos very much.
The best thing ist, that i can learn now, on my old days good electronic stuff that is totally new for me. But your videos are good and your website
make the rest ... i will hope so ...... :) .... to build my own controller and other stuff.
Thank you very much for your work !
Greets from germany,
Peter

[@SatishKumar-si1fl]

I like your tutorials and see attention thank you very much..

[@JoaoNelsonLima]

The next version, print the case on 3D Print. =)

[@SummerBR]

Good Idea even though the way he made it is good. Makes it original

[@tahayasin0004]

Menzil'i kaç metre ?
How many meters is its range?

[@agussp6731]

@@tahayasin0004 about 120 meters

[@TECH_HELPER_irfan]

Superb than all the videos in the entire UA-cam 👍👍👍👌👌👌😍😍😍

[@AnttiMaeki]

Nice job. That looks very much like 1970s radio controllers. They had a metal frame though but it was usually coated with pale brown paint. I wonder where could you find those control stick modules?

[@abelconsiglio2224]

Excelent! Congratulations!

[@beratbaki1681]

Artık bu alıcı ile bir dron toplarsınız.

[@ryansmithza]

I found my old Walkera WK-2402 yesterday, it will be my new Arduino transmitter! 🎊🎉

[@Uditproject-yt5si]

Thank you for the helping😊😊😊😊😊😊😊❤❤❤❤❤❤❤❤❤❤

[@JavierCastro-om3tk]

Muy bueno quedo 👍👍👍👍👍
Un saludo desde Argentina

[@firazpeerjade]

For better range use rfm98w

[@fusseldieb]

What is the difference between the rfm96w and the rfm98w ?

[@ManusWorkbench]

Awesome video brother , i have a doubt could use this transmitter and receiver for quadcopter . If yes could you explain that for me. It will be good if you post another video about this 😊👍

[@vilho4649]

I would not use it with a quad

[@mitofun6967]

Wow! This is awesome!!!

[@evandromp4277]

Top demais Evandro from Brazil!!!🇧🇷🇧🇷🇧🇷

[@kisacaek]

Hocam sayende atölyeme birçok ekipman katkısı yaptım.Kağıt öğütücü / doğrayıcı yapabilirmisiniz. Malum bazı resmi evraklar oluyor imha edecek yer veya durumumuz olmuyor.

[@profezor2]

2 tane kaz yavrusu al, kagıtları altina ser, paramparça ediyorlar 🤣😅

[@peytonsmith8765]

Can you pls send me a link to the joysticks with trim? Great vid btw

[@8.2deck]

They're in the description

[@peytonsmith8765]

@@8.2deck those don’t have trim but I found some that do

[@Matt-rq5yn]

@@peytonsmith8765 hey, i have been looking everywhere for joysticks with trim, where did you find them?

[@ahmetizmir1081]

Güzel olmuş, elinize sağlık.

[@justhamba24434]

Luar biasa MANTAP...👍👍

[@Kendin-Yap]

Flight Test video … ua-cam.com/video/we1i5VTC-9c/v-deo.html

[@gultekineroglu3070]

hocam yeni baslayacaklar icin bu malzemeleri nerden buluruz onu da açıklamalara ekleseydiniz keske

[@bird9]

very good video !
But Can you make an RC controller with just elementary electronic components like transistors, self, capacitors.... Without using components like NRF24l01 or arduino or or...... Please ANSWERRRRRR I am so and so interested by this 💪💪🤗

[@debashishdas4865]

We are eagerly waiting for your upcoming video

[@samerbenmbarek7348]

Bravo good job ❤

[@peace4128]

balık yemleme botu bait boat yaparmısınız?

[@imagineperest9958]

Abi bununla da bir uçak uçursana bakalim menzili ne kadar olucak hazir onceden yaptigina entekre edebilirsen etmeye çalışırsın

[@profezor2]

Menzilinin çok iyi olduğunu düşünmüyorum.

[@acelectronic2831]

wwow good arduino project, thanks you

[@premkumarms1772]

Mannn that is awesome and im following your video to make my own. Ill really appreciate if you could add an oled display to it really liked it maann

[@sakofar3506]

Thanks for this video. Can I know your name on the Facebook page in order to speak privately, please

[@indunilprabhath1484]

great video, how to controlled drone using this transmitter and receiver, please make tutorial , thanks

[@motivational67624]

Very Nice.. In Bangladesh 🎉

[@manishgowda8641]

Awesome work really helpful

[@sakofar3506]

I have some questions for this work

[@BakshishSingh-rc6ki]

What is the total range of transmitter and reciever?

[@John-hg3mo]

he spoke in the commentary that he will test in the next video.

[@keenanjensen5552]

according to the website, 1100 meters

[@AshishKumar-bz4qs]

Ye items kaha se milenge bhai kon bechta he

[@AshishKumar-bz4qs]

@@keenanjensen5552 z

[@tahacevherunal2690]

1100 meters

[@bugracanbagrack3470]

hocam ellerine sağlık mükemmel olmuş :D

[@elbecer]

kardesim , emegine saglik. Ayni seklinde DEVam!

[@MythHoor]

3d Yazıcı kullanarak yapmalısınız artık. Her vakit karton olmaz yani

[@berkaypolat6621]

İnsanlar da yapabilsin diye uğraşıyor bence. Ve bunu 3d yazıcı ile yapsa kanalın amacının bir anlamı olmaz çünkü her evde 3d yazıcı yok

[@MythHoor]

@@berkaypolat6621 Her evde joistik ve RC alıcılarda yok. Haklısınız ama evde yapılabileceğini söylese How to Home a make olarak başlık atar.Söylemek istediğim daha kaliteli bir video da ortaya çıkmış olur.

[@hafsathkk8236]

How many meters are range in this remote control

[@devashreenasare950]

120

[@patrickczader3995]

You could map it to whatever range you want. Like if u wanted precise control u could do 0-50 but if u want the full range just do 0-180

[@Crystalservices]

3 misguiding comments 😂

[@pinobarberio6193]

Hi, I just made the remote control that works very well, except that the joy on the left is not at zero, but with the kk2 and not only, it oscillates between 9/10 values. I saw in the video that your radio control has in trims ... but I couldn't find them ... putting these could solve the problem of these variable values. Thanks for your reply and always great compliments for your accomplishments of which some have successfully succeeded me ... a greeting

[@prateeksharma1981]

Thanks for teaching me this

[@dahamdhibihansa9843]

What's the library

[@huseyinakcit1165]

Usta senin kanalı yeni keşfettim, çok şey kaçırmışım, başarıların devamını dilerim....👍🏼👍🏼👍🏼

[@alaminsnighdho3818]

great work

[@radenaguspurwardi2025]

Excellent projects..

[@galendcia]

awesome works

[@amazingthings1702]

AMAZING VIDEO.I REALY LIKE IT

[@samiabbasi4278]

Good morning, all your project s are very nice, I have a question : what is The most radio transmitter in the 2 this models : FLY-SKY OR FUTABA T8J ?

[@math_bilingue_college7944]

good job , thank you !

[@truescalefpv4089]

Nice project👏
Can you please show how to get PPM signal from this transmitter for scenario where I want to connect a different radio module, or if I want to use as trainer in buddy box, or if I want to connect to an RC USB dongle for flight simulator. PLEASE I NEED TO MAKE ONE FOR THAT TYPE OF APPLICATION😎

[@vaampa_gaming69]

Nice vdo bro...I like ... I wanna try to make an rc car ..with this remote .....❤️

[@rubialugattimoreira1978]

Fantastic! Thanks.

[@erolzabunoglu6295]

Çok iyi. Eline sağlık.

[@pkf4124]

Nice job

[@mezat8745]

Abi senin projelerin bize çok yardımcı oldu
Seni bulursam elinden öpücem

[@Wagnorama]

muito legal parabéns

[@ahmetoguzhan7122]

Şuan bu işin maliyeti 377 TL tuttuyala😲 bu paraya 6 kanallı uzun menzilli bir kumandaya sahip oluyorsunuz! Bu devirde imkansız gibi bişi😕 her ne olursa olsun bu kanalın ve bu adamın emeği yenmez! Bu kalitede ki bir videoyu hazırladığı için ne kadar teşekkür etsek azdır😉

[@MEKATRONA]

Çalıştı mı

[@ahmetoguzhan7122]

@@MEKATRONA evet ama ben artı olarak şarj etmesi için TP4056 Type-c 1S 3.7V Lipo/ lityum pil şarj devreside eklemiştim ,

[@maximilianworld4113]

Good job.

[@suleymandogan8205]

kendi milletimden bu kadar uğraşıp ticari amaç gütmemeniz beni şaşırttı. genelde bizim toplum iyi bişeyi bedavaya kolay kolay yapmaz. umarım hal ettiğiniz yere gelirsiniz.Tekrardan elinize emeğinize sağlık

[@unity3d706]

Keep it up upload some more videos plz bro like this

[@Rubafix989]

Great project ;)

[@mundotudofacil7624]

Show. This is excellent.

[@movingears5582]

Hello! Have you tried programming the BK2461 (FLIP51) radio module chip itself? According to the datasheet, it has 4 ports for PWM control, which is very interesting. But I can't find documentation anywhere on how to program it.

[@Playersdodigital]

It was great, but it would be better if you made a mix similar to that of model airplanes, integrating this joystick on the right so that when you move it upwards, two servos go upwards and when you move it downwards, the two servos move downwards, when you move upwards. the left one goes up and the other down, when moving to the right one goes up and the other goes down.

[@SAHNI-um1jh]

Will try this 👍

[@bayramarslan6176]

Verimli bir video, emeğine sağlık. abone olmaya değer :)

[@vanderwaltjan]

This is very cool 😀

[@SevenWelt]

Super Video!👏👍

[@nightsaber2272]

I've make rc control almost 20 yrs ago. Even joysticks was handmade :)

[@icanseeyourfuture8674]

How did u get the circiut board?Did u sauder everything yrself??

[@nightsaber2272]

@@icanseeyourfuture8674 Made it myself drawing all by hand. :)

[@icanseeyourfuture8674]

@@nightsaber2272 wow nice🤝🏾.So someone like me who wants to build something cool,what course do u think i should do?Whatd the easiest path to learn to build controls from scratch?

[@nightsaber2272]

@@icanseeyourfuture8674 Best and cheapiest way is to buy)