How To Make Twin Motor RC Model Airplane - DIY Brushless Motor Model Airplane.
Вставка
- Опубліковано 17 вер 2019
- How to make 2 brushless motorized remote controlled aircraft from foam board material.
INFORMATION: The Foamboard is made of foam and the outside is paper-covered. It is lightweight, robust and easy to cut. Easily bonded with hot silicone.
All of my videos : bit.ly/2Z9QVYK
Thank you for watching. Please Remember to Share and Subscribe for More Amazing Videos.
SkyRC Dijital LiPo Charger: ban.ggood.vip/T1oJ
Discount coupon: BGT6X80
Thanks for watching. If you want to support my channel, join.
/ @kendin-yap
Diagrams for dimensions: bit.ly/2NEy4S9
INFO: Two brushless motors may not work with one ESC. In this case, it is necessary to use two ESCs. Some brushless motors can run smoothly. The T-motor brand Air series motors that I use in this airplane work smoothly with a single ESC.
Necessary Materials:
2 pieces of brushless motor 2205 1800-2600KV. (2204 can also be):
www.banggood.com/custlink/GKK...
2 pieces (CW & CCW)
Two Blade 6x4 or three blade 6x3, 5x4.5 propellers: www.banggood.com/custlink/vvm...
OR
www.banggood.com/custlink/KmG...
30A Brushless ESC (35-40A can be used according to the motors you will use):
www.banggood.com/custlink/vDK...
OR
www.banggood.com/custlink/3DK...
OR
www.banggood.com/custlink/DDv...
if you want to use two ESC: 2x 20A ESC: 2 x www.banggood.com/custlink/Kv3...
11.1V 1300Mah LiPo battery:
www.banggood.com/custlink/DKG...
3pcs 35-40mm Wheel:
www.banggood.com/custlink/DvK...
Servo control horn:
www.banggood.com/custlink/KKK...
4 or 6 channel radio control system:
www.banggood.com/custlink/mKG...
4 micro servos (may be 9gr servos):
www.banggood.com/custlink/vvm...
Gold Connectors 3.5mm (for Y cable):
www.banggood.com/custlink/vDK...
Wheel stopper: www.banggood.com/custlink/KGv...
Y extension cable: www.banggood.com/custlink/D3D...
L type nylon clevis keper clip: www.banggood.com/custlink/33m...
Adjustable Linkage stopper (Easy Link): www.banggood.com/custlink/KD3...
Lipo Battery Charger: www.banggood.com/custlink/vKm... OR www.banggood.com/custlink/Kv3... OR www.banggood.com/custlink/GDD...
Hot melt Glue Gun: www.banggood.com/custlink/Kmv...
Pushrods: tinyurl.com/feccnxaf
2mm Rod For Landing Gear: tinyurl.com/rtxk9b9x
Some of the shops that sell Kraft Foam Board:
www.amazon.in/Pacon-Water-Res...
pacon.com/board-480/water-res...
tinyurl.com/4ups272k
www.foamboard.shop/en/foamboa...
www.enasco.com/p/Pacon-Water-...
www.mwmaterialsworld.com/es/p...
SJ5000X Camera: www.banggood.com/custlink/Gvv...
Technicial Specifications:
Lenght: 60 cm
Wing span: 87 cm
Flight weight: About 715 g
Center of gravity: 4-4.5 cm from the front of the wing
Required control system: 4 channels, 4 micro servos
Suitable battery: 11.1V 1300Mah - 1600Mah Lipo battery
Suitable motor: 2205 - 2204 (1800-2400KV)
Suitable propeller: 5x4.5 - 6x4 - Навчання та стиль
This is what I love to see, someone making then flying a project from basics . Just as I remember it was when building involved thinking from first principles, most important well done love it. Such a tonic to watch. 👍
I watched the whole video and I felt so happy when the aircraft was flying...
On
this is amazing... good product and creative. . And also when i search the video i found a video like yours. it also look yours one. here is the link. ua-cam.com/video/BFcrTgH12hE/v-deo.html
Diyanath Dissanayake save
Save to photos
Me too! Great job!
I'm a newbie in this hobby and started exactly from this plane. Nice tutorial. Thank you! Hope to see "Mig 17" with 3d printed turbo engine build from scratch
Wow that's a very impressive project, from the design and construction of the plane, to placing a video camera on the nose of the plane -- so we can get aerial views of the surroundings below. It's a job well done. Thanks.
Bautifull plane
飛んだ瞬間感動した。マジスゲ!
Thank you very much for this engineering project. Its fun and lovely.
I love your work and I watch your video very fondly you make very good video and I like your channel very much hope you are well
Thank you very much for reminding us that we will be grateful to you
Excelente trabajo amigo mi hijo y yo admiramo por completo el video....! Felicitaciones, Saludos.!!
すごい!ワンダフル。脱帽。少年魂を忘れない人。感動。(^^♪
Are you mad
Hi
03054391750
what a lovely rc plane making with neat explaination? simply superb flight but the hard work behind that plane is mind blowing.cheers from india.
amazing, great proyect and the process is very enjoyable. Maybe someday use this video to build one
Thanks for sharing. It is so exciting to see the airplane take off at the end and land safely.
Good job. A lot of work went into the making of this aircraft. Nice to see you get it to fly. When I built mine, on the maiden flight, I flew it into a tree!! I still have a good laugh after all these years!!!
Congratulations for your working that make Motor Model Airplane flying well , good sir !
Nice plane and a nice day
Elinize sağlık
Congratulations! became a powerful model plane with excellent controls.
The best DIY of my life...amazing...thanks man...
Luar biasa.. mantap.. sungguh saya salut dengan karya anda... saya sedang belajar RC airplane.. maaf saya tidak bisa bahasa inggris..
Terimakasih..
So nice work you have done dude....
Все четко и понятно! Шикарный самолет для первого раза!
Nicely done and well documented. I love scratch building too for over 50 years. Excellent work.
One of the best flying creatures I've ever seen, and a professional video maker made also.
The video was so gentle and I just loved it.
All the steps are shown which makes it easier for us to make.
I will also try to make the same.
LOVED IT...!
Did you make it?
Tjakepzzz 👌👍 Sangatzzz
Creative ✈💯👏
Very 👌👍 Nice
Congratulations young fellah. This is the best build-it video that I have ever seen!
I finally made a plane and 6ch controller in accordance with your guide. Thx for your video.
Ohh I see your wonderful item list. THANK YOU FOR LISTING IT.
Wow I need to save for a year or more. I have to be patient.
AMAZING! MASTERCLASS! THANK YOU VERY MUCH! MASTERCLASS!
It was so nice to see it flying after all that work :)
ikrrrrrr
ضجثكوثثيكومقاافتطدثجثد
What a beautiful plane smoth landing
sou apaixonado por essas coisas
what incredible work. Congratulations.
Hocam eline emeğine sağlık. Uçağa kamera koymak ve görüntü almak çok güzel olmuş. Böyle görüntüleri bundan sonra ki videolarda da bekliyoruz 😊
I'm happy that it fly, great work!
I love this project. Great work boss. I'LL try to replicate it to make one for my younger bro I'm sure he'll appreciate it. Great work.
thank u bro for making this video im a beginner thanks a lot
Very detailed... I like the attention to detail about adding reinforcements. I am a bit worried that I will not do the placement of servo on the wings... Can you provide more measurements for that. All-in-all amazing build.Loved it.
It gave me so much fun to watch building this plane from a piece of foam till it was all finished. The only thing I did not understand and love to learn was the connection of circuit
Its really simple. The battery is connected to an ESC, which controls the speed of the motor, and provides a stepped down current for the receiver to work with and the receiver sends a PMW signal to the servo to tell the servos what position they should be in and sends the same type of signal to the ESC to tell the ESC what speed it should drive the motors at. Its really simplified but i hope it helps.
Ne kadar keyifliydi anlatamam =) Birçok teknik öğrendim, en kısa zamanda deneyeceğim. Teşekkürler
Mera channel ka video thoda dekhlo
@@gopalkishanpanda6623 Bhai wo Indian nhi ha
One day
Git hazirini al daha ucuza gelir
Good work, model flew just like a full scale.
We made this project for our college program and finally we got success✈️
Glad to hear. I was thinking of doing something similar.
Which type of problem you faced during making this project please tell me bro I'm also trying this project
@@madhiyand516 1.weight of the plane because lack of availability of foam board
Oh and you actually put everything needed to do it ourselves in the description i love you
i love you too
MaşaAllah vallahi helal olsun.
I watched the whole video and I felt so happy when the aircraft was flying.
Vou
Oi, tudo bem eyu8yfm
O governo do lii880pi
I don't understand your language
@@manasedwankar1330 Nobody does... :)
Good
Great video!
You inspired me to build my airplane model :D
And he put a camera in it too! Good job! 💯💯💯
Emeğinize sağlık muhteşem bir çalışma ⚒ 👏🏻👏🏻👍🏻
This is SOOooooooo COOL! I sent the link to my Grandson!
I really like it, when I had ample amount of time, I didn't have money to make like this and when I had money I dont have time.
If you can get a radio and reciever, a motor, a few propellers (cuz you're gonna bust a few), an ESC, and a Lipo battery, the hard parts done.
He puts alot of work into something that wont last for most people. If your new to it, you're gonna crash ALOT. Dont put alot of money into the plane. Dollar Tree sells 20"×30" foamboard for $1.
I found its cheaper, easier, and more fun making tube planes. Basically, you make 2 different sized tubes (3"× 2 1/2" and 2 13/16"× 2 5/16" ((the smaller one is 3/16ths smaller on all 4 sides so it fits snug in the bigger tube. Big tube is "30 long, smaller is 20" but is cut in half. One half holds the motor, esc, battery and reciever. Preferably in that order. The end with the receiver slides into the bigger tubes about 5" in. The vertical and horizontal stabilizers are glued onto the other half, allowing 5" to slide into the big tube. Elevator and rudder servos are mounted through the top of big tube about 5" from the rear if big tube, where wiring can extend out of the front of big tube 2 or 3 inches. Long enough to plug them into the reciever while the front small tube is pulled out. Foot long control wires connect to popsicle stick ends at 45° angles with holes drilled in used as control arms. Coffee stirrers used as guides glued to big tube.
The wings are easy. Two boards. Each one 20" long, 8" wide. Just like he shows how to make 90° angles by shaving 45° off of both sides you have to shave about 60° both sides.
This part is easy but important. The top gets curved, the bottom doesnt. So, the top is 9" wide and the bottom is 8". When you get the angles shaved, get a broom handle or long round bar and smash the inside of the top piece near where the they were shaved. This gives the wing the venturi bump. Top of the bump should end up about 1/3 from the front edge. Glue the two ends which should match up. When you've done both halves, glue them together. You should now have a wing 40"× 8". If you know anything about dyhedral angles, nows the time to do that. If not, dont worry about it.
I dont do landing gear. Throw and land in grass.
The beatiful thing about this whole thing is that it assembles and disassembles, except for the wing you can disassemble it, but it has to be reglued each time.
When I get it down where I can make a video thats easy for me to explain, I will. That should be soon.
Kittelizer Laurelott have you build this design
Kittelizer Laurelott can you tell me if you use 2 motors for one ESC will it effect your motors power or speed or will it stay the same
@@vedpatel8365
No. I think you gotta use one for one. If you put two motors on one ESC, they'll both run slow and/or fry the ESC. I think.
Kittelizer Laurelott your right I think this video is fake. Fake like he really did build the plane but he is not providing real links or links to the electronics that he used. He is showing use links from the same company maybe he has a brand deal with them. He also uses different ESC battery and motor and they aren’t the same as the one he provides in the link below. When I ask him for the real link he didn’t really so I moved on from this video and saved my money. I would do the same if I was you.
Dude, that's awesome. From 27:37 I felt like I was flying this thing, OMG.
Search up FPV. Its basically a hobby where people strap on really low latency cameras on their aircraft and fly it around
Buen trabajo y bien explicado sigue asi
Beautiful work, dude! Really nice! 😃
You should try putting FPV in one!!!
MC's Creations. How are you not verified? 8.4k subs?
German Hunter UA-cam sucks
depressed as always. Yeah no kidding
@@monkeyman7048 No idea, dude. Go figure. 🤷♂️
The landing was so smooth
✈️✈️✈️🛩️🛩️🛩️🛫🛫🛫🛬🛬
@@saiyadaajafri1901 thanks for the sign language I was not able to understand it in English......
I watched the whole video and I felt so happy when the aircraft was flying........................!
Les doy las gracias por sus bonitos vídeos que suben aquí en interné atodos ustedes ya quetienen bien su memoria porque yo no pormi en fermedad
すばらしい
adorei,cara ficou show parabéns
Very good and detailed demonstration and making of sturdy and feature full plane . Very good flight test, the flight and its recording is wonderful and in a nice location. Superb, brilliant!
25:21 to 25:31 low budget rc plane shaped rc car
edit:
great video man ..looks dope
I wish i had the skill's and the experience, great job.
its quite easy
Very impressive! Nice video. A big thumbs up from Moi University in Kenya.
Worthy of applause. I salute you. It was like watching a skylark my favourite bird.
Thank you
So Nice , a good Idea for a Beginner like me I will built it
helal olsun wallaha mükemmel yapmışsın ellerine sağlık
Excellent
Superb
Mind-blowing
I wish I could be there while DIY n test...
with u
God bless you
Thnk you
I never knew something that small could travel that fast by propelling air!
Mantul bosq.
Like
I love your hard work keep it up
Excellent job Turkish Brother. Love from Pakistan.
I thought he from russia
Çok güzel ellerinize sağlık bayıldım
Great work GOD BLESS
So beautiful. You are a great master. Thank you for this video.
Impresionante!...buen trabajo
bro this is godly! love the way how it flies
Hey, thanks for the design. I built one. Very easy to build (If you have built a foam plane before.) I have everything on have to build it except the motors. They are on order. Can't wait to fly it.
Önce her zamanki gibi yabancı bir kanal izlediğimi düşündüm sonra bir baktım ekranda Türkçe yazılar yazıyor.Nasıl sevindim anlatamam.Sonunda uçakta uçtu ya 10/10.😎😎😎
Would you please tell me where is the location of this RC runway?
One of the best helpful features of your DIY channel is the English text instructions.
Thanks a lot man for your effort and yet for your kind will of sharing your lovely hobby videos.
Keep on enjoying us with your amazing projects.
This RC Runway is located in the Kurtköy district of İstanbul
@@Kendin-Yap yapıp satarmisiniz fiyatı ne olur ? Biz sizin kadar kabiliyeti değiliz basarilar
That's it; I'm making one! Excellent video brother!
I am too
this was awesome to watch, so inspiring. i suppose learning to fly one of these planes is the first step before building one!!
parabens... belo trabalho....e muito bom o vôo.
The most useful videol in Yotube history. :) Amazing work. I hope I can make a model plane this like.
Здоровский самолётик получился ! У вас руки растут из правильного места !
The illustration is detailed and precise. Imagine the level of precision that will be required to design a real aircraft. Awesome!
its a real pain
Sir what material need to make this airplan
Nice work! Here, we can't get those type of foamboard easily. I have a wing made for a flite test cub. I also have 2306 motors laying around. I think I'll make your fuselage and mate it with the wing. I've always wanted to build a twin motor plane
Me 2
what material did you use for the wings?
Polystyrene foam board
Красавчик все понятно и легко.
gerçekten güzel oldu. Eline sağlık..
Videoya boş boş müzik koymamanız iyi olmuş. Çok kafa ağrıtıyordu. Böyle yapılış sesi daha hoş😊.
Thank you so much brother you really made my day and I felt happy that people like you exist thanks bro I hope you have much more good ideas
Thank you.
@@Kendin-Yap No problem
I can see you worked too hard for it .
I wish that I can also make it like you.
fun with Ashish nice job I will make a drone
@@oyeniyioluwaseun2598 ya I can also make it. If you have that much of skills then you can make 😋😛😝
I like how the propeller's sound is like YEEEEEEEEEEEEEEEEEEEEEEEEEEE
Agree
Cuando lo he visto por primera vez me quedé sin palabras ,.very good
Dude this video is very informative. I watched through the whole video.
eduado tinamo
fjddjzzn
fjfzhnzzjkss
qeyhakz
hkgd
bau scquedodo
mididamapa ....x lucas
wow it's really awesome!! 4 thumbs up for you bro
Спасибо за открытый проект! Лайк и подписка!
Thank you open source!
Harika çalışma. Tebrikler ve teşekkürler.
Magnífico!
This project was great.
Chất lượng, Sỹ Luân chắc thích bản Cover này lắm này! Chúc mừng em cùng toàn thể Ekip F. Studio
what a genius!! love it.