Thanks for the video, was able to replace my kids in his 08 mariner. No more worrying if it will start for him! Your link wasn't working for me, but I found the part for $45, came with the new switch as well. Had it swapped in about 30 minutes. thank you!
Ordered the part listed three-year affiliate marketing thanks for the tutorial. Can't wait to get the part and fix my mom's car already replaced the starter solenoid and cables... 🙃
So if you can push the key in towards the column firmly and it will start, your issue is definitely the lock assembly. It's a relatively easy fix and will save you a fair bit.
Everybody else was telling me I had to pull the steering wheel and grind that break off bolt. Saw your video and in 30 minutes I had it all apart. About that much time to get back together after I got the part. Thanks $600 times.
You're amazing man. My daughter called me to say her car wasn't starting and she couldn't pick up her little brother. I watched your video, was able to bike over to autozone (they only had 1 left) and about 20 mins later, car starts right up WITHOUT HAVING TO JAM THE KEY INTO THE STEERING COLUMN.
Just changed the ignition assembly today on my 2008 Escape. Great Video....I watched it and referred to it throughout the entire process. Worked like advertised...thank you so much! It took me about a little over 3 hours from start to finish. I had to run to harbor freight to get a tool to remove one bolt. Once again, thank you!
Thanks for the video, it sure made the job possible!! I had a hard time getting the key assembly back into the new ignition assembly. Ended up having to turn the "D" shaped part back and forth from the opposite end of the assembly while putting the key assembly in slowly.
Just fixed my car for $200 instead of $450+ I needed to tow it to the shop as well .. would’ve been well over $500 for all of that .. thank you so much for your video! Did this in about an hour. Crazy!
6:40 was the worst part of the whole job, my name-brand ratchet was too bulky to get in there so I had to make a trip to Harbor Freight. I bought $12 of junk, but I got the job done! Thank you for posting this, you saved me $550.00
@NotSoGrandGarage it's been acting up since we got it in July but it has only happened 3 times before and she found a video on her own to jiggle steering wheel last time but wasn't working today. When I get home from work headed up there. Just ordered part and will have tomorrow. Thank again for video lot better than pulling steering wheel
The key doesn't need to be reprogrammed to change the mechanical part of the switch. You're not replacing anything electronic if following the video. What parts store did you go to?
@@erikajohnson6858 tell them you need the "Ignition Lock Housing" Dorman Part# - 989-019 It's the mechanical part of the switch assembly so nothing to program or anything.
I have been doing the press hard and turn thing for a couple months now ('11 Mariner w/ 260k miles) and I think its finally giving out completely. My question is this, if needing to replace the whole assembly anyways, would it be just as easy to get a remote start option installed? Or is that something completely separate? Sorry if that's a very dumb question.
Not a dumb question and in theory, it could work assuming the start function is the only issue with the switch/cylinder. With that said, the switch is probably cheaper than a remote start kit.
I woudln't go that route. The keys won't be coded to the doors and I'm not sure if it uses a transponder or not. I think it does which means you'd have to tow it to the dealer and have it all reprogrammed (if possible... I'd call the dealer first and make sure they can do it).
@@ralphwhitaker8761That I don't know. I know they can program the fob to open the doors and such assuming you have an original key. The physical key won't match the door at that point though
Great video, I appreciate you. I would like to buy that part . That is what happened to my daughter's Mercury Mariner. Can you tell me the name of the part or how I can order it.
Man im trying to do this myself but the issue im having is that the 5.5mm socket is way too small as is 6 and 6.5. But with 7mm it like too big. Whats up with that
Which screws? If 6.5 is too small and 7 is too big, I'd try standard sizes. It's possible someone has had it apart before and replaced the screws with something else.
I'm having this exact issue on my Mercury Mariner. Do you happen to have the part number of the first item you tried? I'm assuming it's the whole Lock Assembly but I'd like to try this first.
![Lp. Сердце Вселенной #60 РОЖДЕНИЕ ЛОЛОЛОШКИ [Финал] • Майнкрафт](http://i.ytimg.com/vi/YoR0pAV9FVQ/mqdefault.jpg)
Thanks for the video, was able to replace my kids in his 08 mariner. No more worrying if it will start for him! Your link wasn't working for me, but I found the part for $45, came with the new switch as well. Had it swapped in about 30 minutes. thank you!
Glad it was helpful. Yeah for some reason, it's been out of stock for a bit. I'll update the link. Thanks for letting me know.
Thank you so much for your tutorial, it helped me replace the ignition module by myself. This saved me so much money. So again, Thank you
No problem! Glad it was helpful!
Ordered the part listed three-year affiliate marketing thanks for the tutorial. Can't wait to get the part and fix my mom's car already replaced the starter solenoid and cables... 🙃
So if you can push the key in towards the column firmly and it will start, your issue is definitely the lock assembly. It's a relatively easy fix and will save you a fair bit.
Everybody else was telling me I had to pull the steering wheel and grind that break off bolt. Saw your video and in 30 minutes I had it all apart.
About that much time to get back together after I got the part. Thanks $600 times.
Nice! Glad it was helpful!
Thank you, thank you, thank you, Without your video I never would have tried to fix our old Mariner. I liked the chisel trick. Nice.
Glad it was helpful! Thanks for watching!
You're amazing man. My daughter called me to say her car wasn't starting and she couldn't pick up her little brother. I watched your video, was able to bike over to autozone (they only had 1 left) and about 20 mins later, car starts right up WITHOUT HAVING TO JAM THE KEY INTO THE STEERING COLUMN.
Easy peasy! Glad it helped. Thanks for watching!
Just changed the ignition assembly today on my 2008 Escape. Great Video....I watched it and referred to it throughout the entire process. Worked like advertised...thank you so much! It took me about a little over 3 hours from start to finish. I had to run to harbor freight to get a tool to remove one bolt. Once again, thank you!
Good deal. Glad it helped and thanks for watching
Thanks for the video, it sure made the job possible!! I had a hard time getting the key assembly back into the new ignition assembly. Ended up having to turn the "D" shaped part back and forth from the opposite end of the assembly while putting the key assembly in slowly.
Thanks for watching. Yeah they can be a bit tricky but glad you got it
This helped me so much I was able to fix my car within two hours which allowed me to still make it to work the next day
Glad it could help!
Just fixed my car for $200 instead of $450+ I needed to tow it to the shop as well .. would’ve been well over $500 for all of that .. thank you so much for your video! Did this in about an hour. Crazy!
Good deal! Glad it was helpful. Thanks for watching!
6:40 was the worst part of the whole job, my name-brand ratchet was too bulky to get in there so I had to make a trip to Harbor Freight. I bought $12 of junk, but I got the job done! Thank you for posting this, you saved me $550.00
Glad it was helpful! Thanks for watching
Great video thank you!
No problem! Thanks for watching
You are a lifesaver, my man!!!!! every trick you showed worked flawlessly. Thank you.
Good deal! Glad it was helpful
Followed the same instructions.great video.thanks
Thanks for watching and glad it helped.
Thanks for video! My daughter's mariner sitting in walmart parking lot right now cause won't start. Guess I know what I'm doing this weekend
Try to push the key inward firmly while turning. If the problem just started, it'll get it home anyways.
@NotSoGrandGarage it's been acting up since we got it in July but it has only happened 3 times before and she found a video on her own to jiggle steering wheel last time but wasn't working today. When I get home from work headed up there. Just ordered part and will have tomorrow. Thank again for video lot better than pulling steering wheel
@@Darealdirtydonkey no problem!
Is this the same for a 2009 mercury mariner HYBRID??? thanks
I would think so, but I've not done one on a Hybrid model.
well done Sir! Outstanding video 5 Stars!
Thanks
Great job buddy! Great info! 👍👍👍👍🇺🇸🇺🇸🇺🇸🇺🇸🙏🙏🙏🙏
Appreciate it!
I went to buy the part at the store but they said the key needs to be programmed to it. I didn’t see you do this part in the video
The key doesn't need to be reprogrammed to change the mechanical part of the switch. You're not replacing anything electronic if following the video. What parts store did you go to?
@@NotSoGrandGaragecost less auto parts in Vancouver WA
@@erikajohnson6858 tell them you need the "Ignition Lock Housing" Dorman Part# - 989-019 It's the mechanical part of the switch assembly so nothing to program or anything.
@@NotSoGrandGaragethank you so much, it’s very appreciated 😊
@@erikajohnson6858 No problem at all. Thanks for watching!
I have a 2010 mariner, would the part numbers be the same
Should be the same
I have been doing the press hard and turn thing for a couple months now ('11 Mariner w/ 260k miles) and I think its finally giving out completely. My question is this, if needing to replace the whole assembly anyways, would it be just as easy to get a remote start option installed? Or is that something completely separate? Sorry if that's a very dumb question.
Not a dumb question and in theory, it could work assuming the start function is the only issue with the switch/cylinder. With that said, the switch is probably cheaper than a remote start kit.
Do I need to program the key if I get the whole ignition with keys from a junkyard
I woudln't go that route. The keys won't be coded to the doors and I'm not sure if it uses a transponder or not. I think it does which means you'd have to tow it to the dealer and have it all reprogrammed (if possible... I'd call the dealer first and make sure they can do it).
@@NotSoGrandGarage ok thanks, but if it can be done, I think a locksmith should be able to program it
@@ralphwhitaker8761That I don't know. I know they can program the fob to open the doors and such assuming you have an original key. The physical key won't match the door at that point though
Great video, I appreciate you.
I would like to buy that part . That is what happened to my daughter's Mercury Mariner.
Can you tell me the name of the part or how I can order it.
Link to that part is in the video description. If its not in stock there, just copy the part number and search for it that way. Thanks for watching!
Man im trying to do this myself but the issue im having is that the 5.5mm socket is way too small as is 6 and 6.5. But with 7mm it like too big. Whats up with that
Which screws? If 6.5 is too small and 7 is too big, I'd try standard sizes. It's possible someone has had it apart before and replaced the screws with something else.
I'm having this exact issue on my Mercury Mariner. Do you happen to have the part number of the first item you tried? I'm assuming it's the whole Lock Assembly but I'd like to try this first.
Should be SW6958 which is a motorcraft part. Amazon has it and easy enough to return it if it doesn't fix it.
I need a camera person. Actually thats a form of cheating I think. Good stuff!
Lol.. I typically don't either. Appreciate you watching!