GREAT IDEA. Gonna try and make us a few. I read in a comment below about splintering and I have had some guard poles splinter on me. I think that the fiberglass with a coat of flexseal, especially on the handle would really help, especially if the fiberglass started splintering. Thanks.
Thanks for all of your hard work you put into these videos! One thing I can say is If you run the rope through the handle, then cross the rope about 10 times around each side of the tee (should look like an “x”), tie a bowline knot into your slack rope and make it as long as you want. Unless you’re applying 24 kN of force, it won’t go anywhere. I guess the real factor there is how much your rope can withstand lol. But it’s not really that hard to keep the rope tied to the stick. There’s hundreds of ways. That’s just the way I did it.
I made one from a similar garden stake I got at Walmart for around 6 bucks. I used epoxy (JB WELD) and added a small bolt through the pvc and fiberglass area for security. I made one 6 Ft. out of 1/2 inch spike and one 8 Ft. out of 3/4 inch stake. The 6 Ft will serve most of my needs as I fish a lot of shallow water. I also think the 8 Ft.-3/4 in. is considerably heavier but may be useful. I added JB Weld to the tips for wear resistance. If it wears away over time I can always reapply down the road.
The 1/2 inch is very stiff and anchors very well. Built and had my wife use it a couple of times. She likes it. You can slide it through a scupper hole or just stake it in and tie off to it. Her I use it in the ring on my anchor trolley.
I did the Wal-Mart fiberglass pole for mine. For the handle to go the bicycle section and get a pair of rubber handlebar grips, the old school type with the flair flange at the opening. They fit real tight, no need for glue. On the second handle with a razor knife i cut off the flange and use it as a sliding stop with an "s-biner" on my anchor line in between. The rubber ring is real sticky on the pole and stays where you put it.
I used the miracle grow fiberglass stake. I found its diameter to be a little to thick for the areas I fish. Yeah i could get it pushed in but in some areas it really took some effort. So I put on the painters mask and spun it on a home made lathe to get the diameter I wanted.and a rough point. I then to some marine grade putty and on the pointed end I covered it with putty but the. Also made some vertical barbs. Picture a arrow hunting tip. Not the field point. But the triangular hunting point. I formed the putty in that shape around the point fiberglass rod. What that does is even in the strongest currents ive had my pole pull out all except that last two inches of my pole. Kind of acts like a barb on a fishing hook. Works well...
I bought the 1/2 poles from them, but couldn't find a handle that fit it properly. May have to bump it up a size or two then. And that zip tie pool noodle hack is one of the best I have seen for a stake out pole. I lost the only real $80 stake out pole I bought because the noodle didn't hold it up. That's when I began my quest for DIY stake out poles.
Nice work. I use a 6' stakeout pole also, as I'm usually in fairly shallow water too, and anything longer would just be in the way while transporting/stowing it on the kayak. Keep an eye on the garden stake you're using so it doesn't start shedding/flaking fiberglas off into your hands. I believe some fiberglas starts doing that after exposure to wet environnents and UV rays.
I was reading thru the comments to see if anyone made this point> My "school of hard knocks" lesson involves pulling out my rock marker buoy at season's end. The buoy was designed to ride up and down with changing water levels on a fiberglass shaft. After a few seasons, as I grabbed the shaft to lift it out, it filled my palm with glass splinters. I promise, you'll only do it once....
I was thinking of a cheap SUP pre-made handle instead of PVC. At the handle end of a tomato pole, a wood dowel with a 1/4"-20 bolt through the center of the dowel. Inside the handle, a wood dowel with a 14"-20 T-Nut. This way I can mount a camera with the 1/4"-20 thread. Stick the pole/camera in the bottom, then pedal by for the fly-by B-roll shot.
Here are a couple options Option 1: ua-cam.com/video/yVnWF6NKrJ0/v-deo.html Option 2: ua-cam.com/video/EJtHxDm789k/v-deo.html Option 3: ua-cam.com/video/XgSDHecctaY/v-deo.html
I liked ur idea of using a solid fiberglass pole. I was able to get one from Walmart online sold by another seller without having to cut off my right arm to pay for shipping. It’s 8ft and .875. The 3/4 size was only available in 6ft. I was wondering about the weight. The pole weighs 3.5 lbs and was interested in ur thoughts as to whether this is too heavy. I fish off my Bonafide SS107
Post the link to the product if you get a chance so others can take advantage of your find. Mine weighs 3 pounds and I think the extra 1/2 pound on yours will make it easier to stick.
Yes, I explain in this video - ua-cam.com/video/yVnWF6NKrJ0/v-deo.html However, you could do a DIY with one of the PVC gear head adapters I explain with a simple 1" T fitting on top. I am going to make a video on that soon.
Love the video! Where are you guys finding 8' fiberglass poles? I found a 6' fiberglass at Walmart, and I see there are some 8' at Lowes but they are a plastic coated metal which is really thin and can bend/break on you. I'm looking for 8' fiberglass but having some trouble finding one. :( Thanks!
I guess you need to continue to try garden centers. I got mine at AM Leonard, but they only charged $15 for shipping back then. Now it is exorbitant. Maybe see if you can order online thru Lowes or Home Depot with the free ship to store option...
@@KayakhacksFishing We don't have any AM Leonard stores here unfortunately so I'll just keep digging. I know I can get a 6' fiberglass from Walmart for like $7, but I'd really like an 8'. May just try the 6 and see how it goes. :)
The fiberglass is quite dense and will sink, if you drop it, or if the water turns out to be deeper than expected. The pool noodle provides flotation to allow retrieval.
Yes... but I just found out Leonard charges a fortune for shipping now. It only cost a few bucks last year. Try some of the other options folks mention in the comments.
Hey y'all, was just wondering if the pole is made from fiberglass, it would seem that it's not good for the wildlife. Just saying!! An would hate for someone to get a big fine for pollution. I would check an make sure it's safe.😎
I am sure that you can't put any fiberglass in the wild, I mean with fibers coming off of it. It might be covered in the middle but the ends have nothing on them, I was just saying that maybe you should ask the FWC if it would be legally to do so, that's all. Just thinking of the wild life that's all.😎
It's true that a lot of boats are made of fiberglass, but they put two or three coatings on it to seal in the raw fiberglass. If you didn't seal it every time you touch it you would get tiny fibers on you, I speak from experience. I've made a few big fiberglass coolers to store fish in on long trips, it's nasty stuff.😝😎
Thanks for the video. Ever since I broke the DIY Anchor Pole that I saw on UA-cam made from those green plastic/ sheet metal gardening stakes for tomatoes from home Depot I've been looking for a new way to make one. Especially one that's sturdy (I fish Marina Del Rey & Redondo Beach CA). For ocean use.
Me too... i had the volume cranked and had to put my headphones on...other than that love your videos.. you saved me.. cause i saw your video on the fish finder transom / scotty install and made sure I didnt put it on the side of my anchor trolley! Thanks.
Home Depot has a 6 ft fiberglass plant stake with metal tip. I added a 1/2" pvc tee to the end. Less than $10
Perfect!
GREAT IDEA. Gonna try and make us a few. I read in a comment below about splintering and I have had some guard poles splinter on me. I think that the fiberglass with a coat of flexseal, especially on the handle would really help, especially if the fiberglass started splintering. Thanks.
I put shrink wrap tubing on it. No issues since I did that
@@KayakhacksFishing now that's a great idea.
Thanks for all of your hard work you put into these videos! One thing I can say is If you run the rope through the handle, then cross the rope about 10 times around each side of the tee (should look like an “x”), tie a bowline knot into your slack rope and make it as long as you want. Unless you’re applying 24 kN of force, it won’t go anywhere.
I guess the real factor there is how much your rope can withstand lol. But it’s not really that hard to keep the rope tied to the stick. There’s hundreds of ways. That’s just the way I did it.
That is a great idea! Thanks
Made mine a couple years ago like that and love it. Got my stake at Walmart.
I made one from a similar garden stake I got at Walmart for around 6 bucks. I used epoxy (JB WELD) and added a small bolt through the pvc and fiberglass area for security. I made one 6 Ft. out of 1/2 inch spike and one 8 Ft. out of 3/4 inch stake. The 6 Ft will serve most of my needs as I fish a lot of shallow water. I also think the 8 Ft.-3/4 in. is considerably heavier but may be useful. I added JB Weld to the tips for wear resistance. If it wears away over time I can always reapply down the road.
Does the 1/2 inch hold well?
The 1/2 inch is very stiff and anchors very well. Built and had my wife use it a couple of times. She likes it. You can slide it through a scupper hole or just stake it in and tie off to it. Her I use it in the ring on my anchor trolley.
Perfect! Hope other folks see your comment.
I did the Wal-Mart fiberglass pole for mine. For the handle to go the bicycle section and get a pair of rubber handlebar grips, the old school type with the flair flange at the opening. They fit real tight, no need for glue. On the second handle with a razor knife i cut off the flange and use it as a sliding stop with an "s-biner" on my anchor line in between. The rubber ring is real sticky on the pole and stays where you put it.
Thank you for those tips!
I used the miracle grow fiberglass stake. I found its diameter to be a little to thick for the areas I fish. Yeah i could get it pushed in but in some areas it really took some effort. So I put on the painters mask and spun it on a home made lathe to get the diameter I wanted.and a rough point.
I then to some marine grade putty and on the pointed end I covered it with putty but the. Also made some vertical barbs. Picture a arrow hunting tip. Not the field point. But the triangular hunting point. I formed the putty in that shape around the point fiberglass rod. What that does is even in the strongest currents ive had my pole pull out all except that last two inches of my pole. Kind of acts like a barb on a fishing hook. Works well...
Now this a damn good hack. 👍
Thank you
I bought the 1/2 poles from them, but couldn't find a handle that fit it properly. May have to bump it up a size or two then. And that zip tie pool noodle hack is one of the best I have seen for a stake out pole. I lost the only real $80 stake out pole I bought because the noodle didn't hold it up. That's when I began my quest for DIY stake out poles.
lol! My expensive one is on the bottom as well!
Miracle grow fiberglass plant pole is 7 bucks at Walmart and you can put any handle you want on it
they don't carry it anymore
Nice work. I use a 6' stakeout pole also, as I'm usually in fairly shallow water too, and anything longer would just be in the way while transporting/stowing it on the kayak.
Keep an eye on the garden stake you're using so it doesn't start shedding/flaking fiberglas off into your hands. I believe some fiberglas starts doing that after exposure to wet environnents and UV rays.
Hmmmm. good point. I think I'll cover it with shrink wrap
@@KayakhacksFishing Shrink wrap is a good idea.
I was reading thru the comments to see if anyone made this point> My "school of hard knocks" lesson involves pulling out my rock marker buoy at season's end. The buoy was designed to ride up and down with changing water levels on a fiberglass shaft. After a few seasons, as I grabbed the shaft to lift it out, it filled my palm with glass splinters. I promise, you'll only do it once....
Very nice. Doesn't get much tougher than fiberglass!
That sucker could double as a way to terminate vampires.
I thought it had to be a wooden stake! lol
I was thinking of a cheap SUP pre-made handle instead of PVC. At the handle end of a tomato pole, a wood dowel with a 1/4"-20 bolt through the center of the dowel. Inside the handle, a wood dowel with a 14"-20 T-Nut. This way I can mount a camera with the 1/4"-20 thread. Stick the pole/camera in the bottom, then pedal by for the fly-by B-roll shot.
Give it a shot and let me know how it works!
I love your show, but I'm not sure how the best way to connect to my kayak
Here are a couple options
Option 1: ua-cam.com/video/yVnWF6NKrJ0/v-deo.html
Option 2: ua-cam.com/video/EJtHxDm789k/v-deo.html
Option 3: ua-cam.com/video/XgSDHecctaY/v-deo.html
Do you stake through the anchor trolley or attach the pole to a piece of rope?
I always go through the ring in the anchor trolley so I can pull the trolley to position the kayak.
I made one like that, and I made one out of a 98" plastic coated steel pipe, garden stake, it's lighter, and very strong.
Good idea! Thanks
Great tip! Thanks
Glad it was helpful!
This is what I use, I'm sure I got the idea from that same subscriber, Key West Kayak Fishing. Works great! I like your handle line attachment
I feel like you was in my shop watching over my shoulder ...... I just built dang near same pole ...set the hook brother.
I liked ur idea of using a solid fiberglass pole. I was able to get one from Walmart online sold by another seller without having to cut off my right arm to pay for shipping. It’s 8ft and .875. The 3/4 size was only available in 6ft. I was wondering about the weight. The pole weighs 3.5 lbs and was interested in ur thoughts as to whether this is too heavy. I fish off my Bonafide SS107
Post the link to the product if you get a chance so others can take advantage of your find. Mine weighs 3 pounds and I think the extra 1/2 pound on yours will make it easier to stick.
Kayak Hacks Fishing I just checked and unfortunately the link is no longer there.
We love your videos
I really appreciate that! I'll work even harder!
Another great video!
Glad you enjoyed it!
Is there a bracket on the boat that it goes in?
Yes, I explain in this video - ua-cam.com/video/yVnWF6NKrJ0/v-deo.html
However, you could do a DIY with one of the PVC gear head adapters I explain with a simple 1" T fitting on top. I am going to make a video on that soon.
It would be helpful to know what diameter you used.
The stake was 3/4. But.. I just found out A. M. Leonard does not ship these cheaply any longer. Try home depot or Walmart.
I sharpened a wooden 5' flagpole, tied on a piece of pool noodle, and have used it for over 8 years. It's ugly but light, easy, cheap, and works fine.
Great idea! Thanks
Yep that's how I built mine. Bought a 6' fiberglass tree stake at Walmart for 7 bucks.
Perfect - even cheaper than mine
Love the video! Where are you guys finding 8' fiberglass poles? I found a 6' fiberglass at Walmart, and I see there are some 8' at Lowes but they are a plastic coated metal which is really thin and can bend/break on you. I'm looking for 8' fiberglass but having some trouble finding one. :( Thanks!
I guess you need to continue to try garden centers. I got mine at AM Leonard, but they only charged $15 for shipping back then. Now it is exorbitant. Maybe see if you can order online thru Lowes or Home Depot with the free ship to store option...
@@KayakhacksFishing We don't have any AM Leonard stores here unfortunately so I'll just keep digging. I know I can get a 6' fiberglass from Walmart for like $7, but I'd really like an 8'. May just try the 6 and see how it goes. :)
Can you purchase a fiberglass tree stakes like that at Home Depot, Lowes, etc?
I'm sure you can. I almost bought 1 from Walmart the other day. Look in the gardening area by the tomato stakes
I hope so since I just saw what Leonard charges for shipping now...
Im confused on what the pool noodle is for?
With the stakeout pole stuck how could you lose it?
If the pole falls off the boat or if you have to pull the pole to chase a fish, the floating pool noodle allows you to come back and pick it up
The fiberglass is quite dense and will sink, if you drop it, or if the water turns out to be deeper than expected. The pool noodle provides flotation to allow retrieval.
What size is the pole? 3/4? Thanks for vid
Yes... but I just found out Leonard charges a fortune for shipping now. It only cost a few bucks last year. Try some of the other options folks mention in the comments.
Hey y'all, was just wondering if the pole is made from fiberglass, it would seem that it's not good for the wildlife. Just saying!! An would hate for someone to get a big fine for pollution. I would check an make sure it's safe.😎
I have never heard of that. It is covered with plastic, so I do not believe it is an issue. What state would prohibit it?
I am sure that you can't put any fiberglass in the wild, I mean with fibers coming off of it. It might be covered in the middle but the ends have nothing on them, I was just saying that maybe you should ask the FWC if it would be legally to do so, that's all. Just thinking of the wild life that's all.😎
@@pinkydavis4223 thanks - I really wonder about it though when you consider the thousands of boats made out of fiberglass
It's true that a lot of boats are made of fiberglass, but they put two or three coatings on it to seal in the raw fiberglass. If you didn't seal it every time you touch it you would get tiny fibers on you, I speak from experience. I've made a few big fiberglass coolers to store fish in on long trips, it's nasty stuff.😝😎
Thanks for the video. Ever since I broke the DIY Anchor Pole that I saw on UA-cam made from those green plastic/ sheet metal gardening stakes for tomatoes from home Depot I've been looking for a new way to make one. Especially one that's sturdy (I fish Marina Del Rey & Redondo Beach CA). For ocean use.
This one will work. No bend at all
I know this is late bro, but lowes had these. Only place around me that did.
You picked this up locally or had it shipped to you house ?
It was shipped last year for a few bucks. I just saw they charge a fortune for shipping now....
Idk if I did something wrong but that website wants to charge me $200 shipping for that pole
Go to Walmart they are around $7 I think
Holy Mackerel! I ordered mine last year and the shipping was only a few bucks. I just tried to order it and got the same answer you did! Try Walmart!
I can barely hear you on this video.
Sorry - I don't know what the issue is. Comes through fine on my phone.
Me too... i had the volume cranked and had to put my headphones on...other than that love your videos.. you saved me.. cause i saw your video on the fish finder transom / scotty install and made sure I didnt put it on the side of my anchor trolley! Thanks.
Be sure and watch Part 2 as well: ua-cam.com/video/xv9HW2PKwq8/v-deo.html
Here's an easy mount: ua-cam.com/video/yVnWF6NKrJ0/v-deo.html
$200.00 shipping for a $6 fiber glass pole, SMH! Yes, 2 hundred dollars
I know... they had free shipping when I got mine. Lowes has decent poles as well.
@@KayakhacksFishing got the fiber glass pole from Walmart in the garden section, 6 foot pole for less than 10 bucks. Thanks for idea, works great.
@@hectorconcepcion5777 that works!
Fill the pvc with sand
Use a 3/4 pvc and fill it with 3/8 wooden dowels. Cut at an angle and fill the tip with cement putty.
👍
It's worked for me for over 6 years now.
It will work better. 👍👍👈🤪