Installing Longtube Headers, X Pipe, and Cat Delete On My C5 Corvette! DIY, Louder With More Power!
Вставка
- Опубліковано 18 вер 2024
- Installing some go fast parts on the corvette. I'll also be showing some tips and tricks along the way. Thanks for watching!
Speed Engineering Long Tube Headers
(great kit, but junk the exhaust clamps and buy some good ones)
speed-engineer...
Exhaust Header Wrap
2 Rolls of 2" x50ft www.amazon.com...
ARP 134-1102 Header Bolt Kit www.amazon.com...
Spark Plug Wire Sleeve Covers www.amazon.com...
IWISS Stainless Steel Cable Tie Gun www.amazon.com...
Cable Ties, 304 Stainless Steel (100 Pcs) www.amazon.com...
3.0 Inch Butt Joint Exhaust Clamp Stainless Steel 2pcs (decent clamps, but not the best)
www.amazon.com...
Thank you for your Service.
💪💪💪💪💪💪💪💪💪💪
Thank you, I appreciate it
Love it! Semper Fi!
I appreciate it, Semper Fi 🤘
Nice channel and Semper Fi!!
I appreciate it, Semper Fi 🤘
That laugh, lol. Thanks for the video, sounds good.
Haha glad you enjoyed it 🤘 thanks for the support!
Header wrap is a great way to hold in moisture and rust the headers out. If you just gotta have it, I’d stop after the primaries.
You are correct. These are also budget headers, and I only drive the car in the warmer months. I'm not really worried about it.
Nice work
Thanks, I appreciate it!
Sounds good!!
Thank you! Definitely a huge improvement, I should have done it years ago! But it still has a long way to go, before I get even close to your level haha.
@@TheKingCoopa My level might be some level of stupidity so dont worry LOL. Keep it up, cant wait to see what else you have in the works
Hahaha for sure. And I also installed a flame thrower kit, just because lol
Frc ....... Nice!!
I appreciate it 🤘 in my other video I did a nice setup of a flamethrower kit lol, just to mess around with. Its pretty fun.
@@TheKingCoopa thank you, i have one of this beauty too ,1999 torch red, we are fortunate, , i follow you bro,,,,,👍
@@richysoto6332 oh nice, thats awesome!! Same year as mine too. Definitely some awesome cars, I love mine. Thank you for the support!
Which steel gasket did you use for the headers? Thanks for the info
Hey, sorry for the late reply. I just used some multi layer steel gaskets.
www.summitracing.com/parts/btc-btr17944?seid=srese1&gclid=EAIaIQobChMI1aKYxoe7-AIV4R6tBh0ZXQ5eEAQYAiABEgKeQvD_BwE
But I ended up going with some remflex graphite gaskets. They are a one time use only. They seal alot better
Remflex 2048 Exhaust Gasket for Chevy V8 Engine, (Set of 2) a.co/d/6P3e9BF
Does police give you a hard time for the tinted covers on your tailights? Mine had them on when I bought the car but I took them off so I didn't get pulled over. Looks so much better with them on.
Hey, I think it kinda depends on your state. Indiana i think is petty relaxed. I've never had a single issue for exhaust, tint, or the tail light tint. I've been running them for years.
Thanks for replying! I'm putting them back on today@@TheKingCoopa
For sure! If you're nervous about it, before I ran my lens covers, I installed the left two covers. Then walked back like 40 feet. I couldn't even really tell a difference in the brightness between stock and tinted. So it made me feel better, and not worried about it at night time. (Unless yours are SUPER dark tint 😅) Hope that helps, good luck with the car, and thanks for the support! 🤘
You bet, I subscribed! Yah, my wife was following me home the evening I picked the car up and she said could barely see the brake lights. I'll need to go check it with me own eyes:-)@@TheKingCoopa
@@shaehatfield1899 oh haha yea. I think mine were from corvette creations. Its been a while, I remember there were kinda expensive though. Thanks for the subscribe!
I have corsa with x pipe do I have to remove that air pump ur talking ab?
Hey, with that setup, you don't have to. I ran that setup for a lone time. But if you go with longtube headers (deleting the catalytic converters) then I would definitely recommend it. It would be useless at that point, and just taking up weight/space.
id pay for u to do this for me, no cap
Hey boss, eventually I'd like to open up a custom shop. I think it would be cool to modify peoples rides. I appreciate the offer, but I just don't have the time for it man. Gotta finish my single cab, its all torn apart taking up my whole garage.
Rah
Semper Fi