Has the F63B3, evolved to newer Models suitable for Aventura's 1054 size vessels ? These seem new Models: F65B3 or F65C or F69A3 or F69C ( as current?)
Hi, I have F63B3 installed. Overhead tank is connected to underground tank with sensors for automatic functionality. Only issue i do see is , at the time of regeneration, if overhead tank is full, water pump doesn't run which makes regeneration steps doesn't work. How do we overcome with this? are there any settings to be changed?
Hi, Do you have a pump from the overhead tank? You need at least 2 bar pressure for the valves regeneration to function, so if it is from a tank it would need to be 20M up.
Sir, can we use this Auto multiport valve for the sand filter & carbon filter..if yes..then what about regeneration setting?? I think their is no require of regeneration to sand filter and carbon filter..only back wash , slow & fast rinses are required.. then what should do about regeneration setting..plz sir suggest me.
Your video has been very helpful. I am probably just missing something but can use your help. How do I know how much water we are using in order to set the number of days between regeneration? I hope i am asking this correctly. I have set it as 7 days at this point but may be too often but not exactly sure how decide the correct setting. Thank you.
The easiest is to test the water for hardness with a test strip just before the regeneration. If you have no hardness yet extend the interval, if you have a lot of hardness then shorten the interval.
Hi, during the fast rinse, the softener resin is pushed back down into place at the bottom of the Vessel in preparation for normal operation. During this process, any excess salt is also flushed out to the drain point.
What happens if we have both this one and the other one? How do we go about setting them? Should they be the same?
This video was very helpful, thank you for your explanation
how to reset it?
Good Morning.
Could you help me where to find to sell the Flow sensor?
How reliable are these valves and how long do they last avg life ? Thanks for the video.
Thank you. Very concise explanation
Has the F63B3, evolved to newer Models suitable for Aventura's 1054 size vessels ? These seem new Models: F65B3 or F65C or F69A3 or F69C ( as current?)
is the volume per min or hour per day?
Hi, I have F63B3 installed. Overhead tank is connected to underground tank with sensors for automatic functionality.
Only issue i do see is , at the time of regeneration, if overhead tank is full, water pump doesn't run which makes regeneration steps doesn't work. How do we overcome with this? are there any settings to be changed?
Hi,
Do you have a pump from the overhead tank? You need at least 2 bar pressure for the valves regeneration to function, so if it is from a tank it would need to be 20M up.
Sir, can we use this Auto multiport valve for the sand filter & carbon filter..if yes..then what about regeneration setting?? I think their is no require of regeneration to sand filter and carbon filter..only back wash , slow & fast rinses are required.. then what should do about regeneration setting..plz sir suggest me.
Your video has been very helpful. I am probably just missing something but can use your help. How do I know how much water we are using in order to set the number of days between regeneration? I hope i am asking this correctly. I have set it as 7 days at this point but may be too often but not exactly sure how decide the correct setting. Thank you.
The easiest is to test the water for hardness with a test strip just before the regeneration. If you have no hardness yet extend the interval, if you have a lot of hardness then shorten the interval.
Thank you, this video very helpful.. 👍
What are the steps for trial running after installation?
Can you explain to me what happens during the fast rinse?
Hi, during the fast rinse, the softener resin is pushed back down into place at the bottom of the Vessel in preparation for normal operation. During this process, any excess salt is also flushed out to the drain point.
Thanks, that really helped!
Hello, how to fix the -E1- error and it continues to beep.
Same. Problem
He nice explanation ..Thank you
seria muy amable de realizarlo en español