How to Turbo Ford Sierra (part 3)

Поділитися
Вставка
  • Опубліковано 3 гру 2024

КОМЕНТАРІ • 24

  • @Kriska98
    @Kriska98 6 років тому +1

    Yea I'm a bit late but yes, that should light up 4:29

  • @bogdan2299
    @bogdan2299 9 місяців тому

    Is the exhaust manifold made from stock?

  • @ahmed-bs9sd
    @ahmed-bs9sd 7 років тому

    kan du inte göra en lista med alla kopplingar å storlek å ungefär hur mycket stålomspunnen slang du har använt? grym video btw keep it up

    • @carculturesweden2668
      @carculturesweden2668  7 років тому +1

      ah med hm, beror ju lite på vilken utrustning man skall använda för att Turbo konvertera, alla saker har inte samma anslutningar men ska försöka hitta gamla kvitton så kanske jag kan göra lite video för sådant :) tackar för feedback!

  • @gaborzaszlavik6176
    @gaborzaszlavik6176 7 років тому

    Hi! For me the same , the 2 things not lightning. I hope it will have any lamp there :D

    • @carculturesweden2668
      @carculturesweden2668  7 років тому

      Gábor Zaszlavik yea in my mind i think those had lights when i bought the Sierra but im not shure, hope someone can confirm it.

    • @loncis
      @loncis 7 років тому +4

      Hi. Both of these have bulbs. 100% they are burned out, just check that and replace bulbs. Good luck.

    • @carculturesweden2668
      @carculturesweden2668  7 років тому +1

      Edgars Lonerts thanks for answer :) just dismantle instrument panel?

    • @loncis
      @loncis 7 років тому

      Just take out that black plastic around the instrument panel and you will see screws for heater (unit??).
      If I remember properly, u should be able to just pull out the cigaret lighter, if not, pull out that pocket near and u probably should see whats happening there. :)

    • @loncis
      @loncis 7 років тому +2

      I apologize if Im wrong in how to dismantle that, as I did it long time ago, but there are bulbs 100%, so just try to locate them.

  • @DzikuSF
    @DzikuSF 7 років тому

    I dont know if you solve that problema already, but many cases of rattling shifter i type 9 gearbox are caused of lack/broken plastic piece in the bottom end of the shifter:
    www.burtonpower.com/saddle-gearlever-to-selector-shaft-type-e-9-gearboxes-gbt9540.html
    Also, about light, there is a grey wire with yellow stripe, for instrument cluster light, cigarett lighter, heather panel etc, so if your speedo is lighten up, you need tho change the bulbs in other places.

    • @carculturesweden2668
      @carculturesweden2668  7 років тому

      Łukasz Dzik OH thanks! :) will give it a try, dont remember if it was missing or broken tho. Will take a look, thanks for the response!

    • @DzikuSF
      @DzikuSF 7 років тому

      No problem, i know how irritating it could be...

    • @carculturesweden2668
      @carculturesweden2668  7 років тому

      alright, the bulbs in the speedo works so it must be the bulbs :x

  • @Osziboii
    @Osziboii 7 років тому

    How about the air mass flow sensor?

    • @carculturesweden2668
      @carculturesweden2668  7 років тому +2

      Erik Mátrai hi! Its not used since im running Ecumaster, the air / fuel is calibrated in the program when Tuned. :)

  • @CopeFPV
    @CopeFPV 6 років тому

    hey man nice job on that sierra.
    And there is light in the board.
    Hire it is how it looks on here's how it looks on mine sierra.
    prntscr.com/hzt6jy
    only that the lighter was ejected at the moment but there are light too,sry for low res

    • @carculturesweden2668
      @carculturesweden2668  6 років тому

      Perica Ristic thanks alot :) yea i managed to change the bulb in the fan speed switch but now i only need to sort out how i change the bulb in heater switch

  • @nikolaitherkelsen8952
    @nikolaitherkelsen8952 6 років тому

    hey M8 cant u see the messages i send to u ?

    • @carculturesweden2668
      @carculturesweden2668  6 років тому

      nikolai therkelsen hi! No i can only see this here

    • @nikolaitherkelsen8952
      @nikolaitherkelsen8952 6 років тому

      oh okay det er fordi jeg kommer fra danmark og er selv igang med mit eget pinto build som jeg måske lige skal have lidt hjælp til ang nogle dele for mit er meget lignede det du har lavet og samt søger jeg lidt dele som måske kan findes i sverige tænkte derfor om det var muligt vi kunne blive venner på facebook ? :) jeg kan addes på Nikolai Kristian Therkelsen

    • @carculturesweden2668
      @carculturesweden2668  6 років тому

      nikolai therkelsen aah kontakta mig på Instagram carculturesweden

  • @kimmikko1
    @kimmikko1 5 років тому

    1 take cossie engine
    2 swap it in
    3 done