Just got done putting this switch in a 2022 refresh with the Duramax. Everything is the same, except getting through the firewall was a pain in the butt. The air intake tubes block it. Removed the first elbow, and access was still tight, but I got it... if you remove the back part of the intake hose, it wouldn't be too bad, but that seemed like it would be more trouble than it was worth. Oh, and finding the wire was a little challenging in the cab. I don't know if the 2022s have more sound insulation, but I had to dig for it.
Nice Job, Don. I just bought this unit for my 2019 Tacoma. It arrives tomorrow and I wanted to jump right in cleaning up all the wiring that some unprofessional professionals left excessed of tangled up under my hood. I've watched a few of the tutorials/reviews for this product and found that yours was presented the clearest and most helpful. Thank you, sir.
I have a Auxbeam and a light bar just like that, I want to learn how to install but I’m having trouble. So I cut the wires like you did in min 14:22 but I don’t know hot to connect to the box which wire goes to negative and positive since it’s it has a red blue and white wire, it’s also a RC led light bar with DRL
Prefer the replaceable relay version, easier troubleshooting. Also if relay fails you can swap positions to put the circuit back in operation. Relays fail, I like the option to replace. I would not like to replace the whole relay power unit because (one) potted relay failed. They should keep the previous (old) form factor and add the RGB/Blue-Tooth features. Don, great videos. Thank-you!
I like how you responded to his video . Great to see someone thinks lie me . I also would like to know if this company will provide any help, customer support and is in the USA most importantly this system is not waterproof from what I can see I put my money on Finex 4200 mini controller made in the USA, they provide lighting equipment for fire, police and public safety
Just wanted to point out that there is also a firewall penetration on the pasenger side as well. Might be a little harder to access from inside the cab though depending on the size of your hands.
Don - loved the video and the step by step install directions. My AR-800 arrived yesterday and followed your video and the supplied installation brochure supplied by Auxbeam. Unfortunately, despite everything being hooked up correctly I cannot get the control box to turn on and illuminate. I tried to reach Auxbeam for assistance but to no avail, and they don't have any Q&A or Troubleshooting links on their website, or none that I could find. My 2016 Toyota Tundra has LOW PROFILE mini fuses, so I used the supplied fuse tap, which is designed for mini fuses, and replaced my 10 amp low profile mini ignition fuse with a 10 amp mini fuse. The supplied fuse tap seems to fit fine into my truck's fuse box, and even with replacing the truck's 10 amp low profile mini fuse with a 10 amp mini fuse the truck started up just fine. I haven't hooked up any accessories yet, but one would conclude the control box should display it is receiving power with or without any attached accessories. Do you think the issue is using a fuse tap with mini fuses instead of LOW PROFILE mini fuses? Any troubleshooting ideas?
Sorry just saw this message. UA-cam flagged it as spam. Have you tried bridging the trigger wire to the main power lead just to test it out for power. That small trigger wire is on a two prong pin. Maybe the other side is live. Just making guesses in the dark
very good step by step explanation - question? the ignition/accessory switch wire - where would I connect it since I can't do your option where you spliced into a red wire? I have 2024 GMC Canyon elevation - please advise
If you leave the light bar on in the switch panel and you turn off you engine and you turn on the engine back on the lights are on or you have to press the on button in the switch panel to turn them on again
If main power is cut from the panel, everything is off and has to be repressed. You can wire it up differently of course. After this video I added a wireless remote that can turn it on regardless if the truck is on or off too
Great video instruction. I see that you connect the remote wire to the ignition. Does that mean you can only turn lights on when the ignition is in "on" position? If so, is there a way to bypass that and give you the ability to turn the lights on without turning on the ignition?
Thanks for taking the time to go through the app. Many videos and still no one has demonstrated the app as clearly as you have. Is the app compatible with android auto? (Disregard, I now know you mean something like carlinkit.) Im looking for a replacement to the CTS2 powerswitch.
Since most of the viewers don’t have the same vehicle, I left it open ended for the ignition trigger. But I did make a video following up: ua-cam.com/video/aV7ey5415dI/v-deo.html
Good morning, For the wiring of the RC light bar. I notice u cap the red wire for the switch, at 14:29 of video {New Switch Panel Auxbeam AR-800} that being said..... you run the WHITE wire into the positive terminal using 30 amp location on AUX box and then the BLUE wire into positive terminal of next switch over ? Using the 30 amp switch right next to it ??? Lastly, do you connect the power leads that come with wiring harness for the light bar or just burying them ? Thanks Don J
Question. If the light bar has 2 color modes (amber and white) , would you need to wire them to separate switches? It looks like you did but wanted to confirm! Thank you. Great video looking to get one for my father in law
I have the Chevy 1500. You used a existing fuse tap. Which fuse number would you recommend to tap into? Engine bay fuse number or passenger side fuse panel number?
Hi, Don. Excellent channel. I am interested in the AR-820, but do not wish to mount switches in the truck. I have a 2023 Canyon Denali, with Google built into the infotainment enter. Do you know if the app could be downloaded to the truck, and I could control my accessories with the screen? Thanks
So I'm wondering if I can cut the switch controls off and tap my DRL so they can work automatically? Then make everything automatic except things like light bars that are not for road use! Maybe i just need to find a way to split or separate the switch controls wire. Great videos keep up the great work!
I was looking to use this panel to run white/Amber pod lights. Would I be able to have 2 switches control each color of the light (set one to run solid white, the other strobe Amber). Would I have the jump the ground between the two switches? Thank you.
I have a newer light bar with amber and white DRL’s. They are hooked up to 3 switches. One for each color and the lightbar array itself. Works wonderfully. You should be able to run each positive wire to each individual switch too.
Hi sorry to bother you, I have a 2022 gmc sierra at4 and purchased the smoked mirror lights with signal lights. Came with no instructions and wondering where would be the best place to run the signal wire to. It's the light on the mirror face
@Donslife I was hopping to tap in the harness in the door if there was a wire for the signal, not sure if there is or not. If not I would have to do it the way you said. Thanks so much for getting back so fast and for your time
If I power off the vehicle “cutting power to accessory wire turning off the unit” if I turn my car back on without turning the switches off first will the buttons that were on. Will it come back on when you start? Or do you gotta turn them back on every time
The switch is designed to turn on and off with an ignition or accessory trigger. You would need to turn the connected device on again after the panel loses power. You can likely do some creative wiring outside of how the manufacturer instructs the installation. Going this route you can forgo using a switch altogether and just use a relay.
@@Donslife hold on I think we might not understand eachother, let’s say switch 1 is on currently, you turn off ur truck without turning off switch one. the device looses power, turn ur truck back on, will switch one also come back on or do you gotta press the button again.
@@uniteddrones7626 sorry! Shutting of the vehicle resets the panel to ‘off’ for all the the connected devices. You have to repress each item or group you have programmed to turn things back on.
Nice video 👍 If my light bar needs 35 amps (420W on 12V) and the switch panel only has up to 30 amps, how would i wire the original harness with a 40 amp relay into the auxbeam switch panel? Would that work? Thanks.
You would hook it up with 40amp harness/relay as per the lightbar manufacturer’s instructions and just use the Auxbeam as a switch. You could use a 5A circuit just for switching the 40amp relay on and off
Here’s one: How to Install a Wireless Compressor for your Air Suspension ua-cam.com/video/pLCIiavqKtE/v-deo.html Later on I add an auxiliary air line too
Is there an option to have the system turn an input on (light bar) when you start the truck instead of having to manually turn it on via the all or in-cab control?
Great Video! Thank You, with the RC Light that comes with three position switch, is it okay for the DRL and the flood to be on at the same time? is it really okay to eliminate relays and fuse holders and tap straight in with this unit? thanks
Thanks! I have looked into the flood light and DRL being on at the same time couldn't get a straight answer. The most of have learned is that it won't hurt it in the short term. The flood light drowns out the DRL too. Each Auxbeam switch has it's own fused circuit and relay so yes, you can eliminate the ones that came with the light bar.
Please someone help been trying to find this information everywhere. I have auxbeam light bar that has a power button and a toggle button to switch from white amber both and stobe would this allow me to turn them on and switch in between the different modes? Thanks
It would have to have each feature (wire) hooked up to separate switches on the Auxbeam panel instead of using the switch it came with. Then you would program each switch to behave how you want it to (on/off, momentary or strobe)
@Donslife would I be able to switch in between the different color modes I don't know if I explained it right. Have a switch with 2 buttons one is on/off the other switches in between white, amber, white and amber then white stobe Amber strobe and white and amber strobe. Thanks for ur info and time.
Ah Don. I was waiting for you to visually show me mounting options inside the cab. Anyhow, I just bought one using the code. Originally $300, Auxbeam is currently already 10% off at $269. With your code it gets down to $243.
Just curious 🤔 if you can have constant power to the panel since you can shut off the lights anyway? More or less if you're at a car show, that you're not having your acc,on
So, theoretically, would I be able to run this purely from my phone without installing the switch panel? I'm looking at getting these for my RHD Jeep so I can finally get some strobes on it, but not super keen on the idea of tearing the dash apart to run the wires. Great video, super informative!
Great vid. Do you know the power the panel uses to operate itself? Like standby power when all the circuits are turned on but no accessories actually drawing power? I have a different panel that draws 1a constantly just to have switches in on position.It’s a bit of an issue and I need to find new panel. Thanks
Yes if you wire it up that way. Here is a video where I can turn it on remotely too: Adding a Wireless Remote For My Accessories! ua-cam.com/video/aV7ey5415dI/v-deo.html
If I have lights that I would like functioning while the ignition is off, does this switch Bank drain the battery if the accessory wire is hooked up to a power source that isn't ignition dependent?
It will drain a little power to illuminate the LED backlights for the panel if the remote wire is connected to an ‘always hot’ source. I left my panel powered up overnight and my vehicle wasn’t really drained. Over a few days it could be a problem. You might want to do something like this : ua-cam.com/video/aV7ey5415dI/v-deo.html
Can you turn the pod light on without the ignition on or no? And if yes, how do you wire where the pod light can turn on without the ignition being on and would it drain battery? Thank you
Great video. I have a question. Can it be operated via Bluetooth with the ignition off? I camp in the middle of nowhere and if something is stirring around camp I would like to be able to "Light up the night". Thanks
great video, have a question.. I install the one thats not compatible with the app. if i get the one with the APP do i have to chasnge just the control pannel?
Good question, as far as I know the control panel that goes in the vehicle is what ‘talks’ to the app. So as long as the switch box is compatible with a Bluetooth capable panel at a later time, I think it would work. I would ask Auxbeam to be sure just in case the physical connections vary. To be fair, I only installed the one panel and haven’t had experience with their other switches/panels
There are two circular grommets on the firewall. One on the driver’s side and passenger side. They are made out of rubber and need the end cut open to pass wires through. That’s what they are there for. In some of my videos I show them
Yes, when the truck is turned off the panel will lose power too and shut off all accessories connected to it. I chose to wire it up this way. In a later video, I added a remote to be able to turn the panel on and off independently of the truck. Adding a Wireless Remote For My Accessories! ua-cam.com/video/aV7ey5415dI/v-deo.html
I am leaning towards Auxbeam > more expensive options but I don't like that I have to turn my IGN on to power up my accessories. Is the app control also dependent on IGN being on?
Fair point. You can wire up the switch panel to constant too. Really up to you…….or you can add a diode and a remote switch like I did in the video. Now I can sit by the campfire and turn the switch on remotely, while controlling all the gadgets. (For example) 😊 Adding a Wireless Remote For My Accessories! ua-cam.com/video/aV7ey5415dI/v-deo.html
No, you can install a remote switch like I did in this video if you wanted: Adding a Wireless Remote For My Accessories! ua-cam.com/video/aV7ey5415dI/v-deo.html
I just got to the part of the video where you said you have a compressor under your hood? I know I didn’t hear that wrong because I even ruined it in. Heard it again, lol. Do you have a video showing the install of your compressor?
There are a couple related to it. Here is the main one : How to Install a Wireless Compressor for your Air Suspension ua-cam.com/video/pLCIiavqKtE/v-deo.html
Hey Don, love all your vids and mods. Will this work just off the auxbeam phone app or infotainment screen without having to run the 8gang controller into the cab?
Thank you sir! Technically you could leave the control panel tucked away somewhere safely in the engine bay away from heat and moisture. Your phone app via Bluetooth would do the controlling. Personally I would find that inconvenient and would want the panel in the cab, even if you left it sitting in the glovebox or something. If you want to control it with your infotainment system, you’ll need something like my CarPlay AI box to control the Auxbeam switches.
I am loving this control panel. One question. Does anyone if it is possible to set the control to power on the last set accessories as soon as it powers up with the car? As it stands now, when you turn the car off, powering off the panel, next time you power the car on, you must press the main power button on the panel to activate it. I would like to set it to power on automatically with the car startup. Is this possible?
A+ work as always! If mine wasnt a lease id consider doing alot of your mods. Have you considered installing the sierra sportsbar from the 16-19 all-terrains? I swapped mine over but on the x-31 package not the at4. Ive had many compliments and would def look good on the artic white!
Gm had a factory sportsbar they offered on the 16-19 all-terrainX packages. I kept mine when i sold the truck and put it on my next one which was the '21 new body style.
Box cover definitely wont work. I had to do a bit of modding to the tonneau cover to make things fit right. The factory covers will not fit either. Only certain aftermarket ones will work.
This look identical to the non rgb non app version. I'm thinking maybe all that functionality is built into the switch itself. My biggest dislike is that it doesn't remember what's on when I turn the car back on. So DRL would be pointless to wire up since they'd have to be turned on every time. I actually mounted my switch to my GMRS radio's mount underneath it so it's kinda like a console of equipment. Love the auto dim feature, works very well. Hopefully this will hold up better than the junk wiring harnesses KC sent me with my lights. Corroded and burned at the relay since it was 1 wire in and 2 out to each 80 watt light. The outputs were fine but the input wire was just burnt.
@@Donslife I was thinking of wiring in a normally closed relay and using the switch to turn it off. But was hoping maybe it could be an option in the upgraded one to just be normally closed vs open. Thanks
Hey Don, a little curious when you are speaking about the "App" and choosing the Colors. Are the Colors associated to the Buttons on the App or colors coming out of your Lightbar?
Hi there, the switch won’t control a dimming function. The light strip itself would need to have a dimming feature that you’d have to adjust with it’s own app or mechanical knob/slider.
@@Donslife This is the biggest question I have as well. I looked and a few others, and they also have this question, but I, unfortunately, don't understand your responses. I do think I understand that it's your pink wire in this video. I went to the compressor video but could not find exactly what you did here. Is there another wire or anything anywhere closer or easier to find? or do you have a video clip of this? Thanks so much for all the videos. Just used a ton of your discount codes so thank you!
gotcha, but to confirm no way to dim the actual lights outside of the vehicle? I have Baja S2s on my roof rack, but at night camping it would be nice to dim them from being too bright
Nice video! Does the controller lose memory of the switches that were on after an ignition cycle from on to off to on again? Engine cooling fan for example should have immediate power without having to turn a switch on each time you start the vehicle. Thanks in advance
When the ignition is turned off the devices it controls turn off too. When the first ignition is on again, the devices need to be turned back on manually but they will stay programmed as groups and/or pulse, toggle and momentarily mode if you set them up that way. I installed a remote control circuit with a diode so I can keep the switch on without starting the truck too.
Why did you put a blank wire end on one of the three wires where you cut off the connector? Was the wire you blanked the illumination wire for the switch that normally connects to that lead?
I am not sure. My assumption would be each circuit is up to 30Amp but don’t exceed 60Amps total running at the same time. You’d have to ask the manufacturer if you can go higher than 30amps on one circuit
Bro can you confirm that the auxbeam panel is defect. A lot of people on UA-cam telling that after a month of use the box is damaged making some equipment on all the time. Replaced by auxbeam but the issue persists.
Mine works perfectly. I was just using it at a car show and had my lights on a strobe effect using the Bluetooth app on my phone. I have not had any issues at all
Underglow kit!! But it has to light the entire area under the truck and hiding the lights is the key! I hated seeing the neon and led strips.... took away the whole effect. Bright white to match the light bar and running lights. All other colors optional lol
@@Juddmann007 I have been looking. I also do prefer the glow and not being able to see the bulbs. So much junk out there, I have been having trouble finding some that look like they’ll survive 4 seasons.
I ran a set of streetglow neons back in highschool but on a car. Not sure if they are still around or even make neon tubes anymore. They held up through several winters and were brighter than any led strips ive seen
Great video, and detailed installation vide. Let me comment that AuxBeam switch panel are crappy products, and customer service is terrible I install AuxBeam switch panel AR-800 according to included brochure, and only lasted 3 days, and I had to fight hard with customer service department to get my refund, I do not recomend this product at all!!!!!
Did you ask Auxbeam if this controller is waterproof system ip67 rated ? What about customer services to take my phone calls if there’s any issues with this 6 or 8 gang controller
Don, great work, Gained a subscriber! I'm curious if you know, I reached out to Auxbeam asking if you always had to turn the switch on (for a specific device i.e. DRL, clearance lights etc) with each power up? They replied with, you will always need to turn the unit on via the on/off button on the control head or thru app once you have either key in ACC or ignition on. Is that true? Does each button have memory of previous use at power off? However, I also wanted to be able to have the unit automatically turn on with ACC or ignition and have the preset lights come on. Trying to eliminate always having to turn the unit on after keying up the vehicle to turn on my DRL and clearance lights each time I start the vehicle. Thanks!
@@robertionescu_ I did get this unit and although it powers up (the buttons light up) if using the accessory lead. Then you can either hit the "memory button" in the center of the unit to turn on any switches/buttons that were on when you previously cut power to the unit or, select which button(s) you wish to turn on individually. It will not power on any items connected to the buttons by default when turning the key on. hope this helps.
Get your AUXBEAM Panel Here:
shrsl.com/3qdzv
Use 12% Discount Code : DONS
linktr.ee/donslife - Links to all of my products and discounts
Oh yes! Finally a DIY channel with clean installs. Clear video quality and angles. Thank you for taking the time to do this. Gained a subscription 💥
Happy to be of service! Lots of videos over the past couple years. Hopefully they are getting better 😂
As always, excellent step-by-step walkthrough as well as post install feature demonstration is greatly appreciated.
Glad you liked it. It takes a long time to film 😂
i install that in my truck 3yrs ago.it works and held up great...and i live in a cold and snowy area like you🤣👍❗
Just got done putting this switch in a 2022 refresh with the Duramax. Everything is the same, except getting through the firewall was a pain in the butt. The air intake tubes block it. Removed the first elbow, and access was still tight, but I got it... if you remove the back part of the intake hose, it wouldn't be too bad, but that seemed like it would be more trouble than it was worth.
Oh, and finding the wire was a little challenging in the cab. I don't know if the 2022s have more sound insulation, but I had to dig for it.
Nice Job, Don. I just bought this unit for my 2019 Tacoma. It arrives tomorrow and I wanted to jump right in cleaning up all the wiring that some unprofessional professionals left excessed of tangled up under my hood. I've watched a few of the tutorials/reviews for this product and found that yours was presented the clearest and most helpful. Thank you, sir.
I appreciate the kind words
I have a Auxbeam and a light bar just like that, I want to learn how to install but I’m having trouble. So I cut the wires like you did in min 14:22 but I don’t know hot to connect to the box which wire goes to negative and positive since it’s it has a red blue and white wire, it’s also a RC led light bar with DRL
I made me some wheel lights out of a 5 gal bucket and the 5050 leds and they work perfectly
Prefer the replaceable relay version, easier troubleshooting. Also if relay fails you can swap positions to put the circuit back in operation. Relays fail, I like the option to replace. I would not like to replace the whole relay power unit because (one) potted relay failed. They should keep the previous (old) form factor and add the RGB/Blue-Tooth features. Don, great videos. Thank-you!
Thanks for sharing! Weighing the pros and cons as you research what works best for your project makes sense
I like how you responded to his video . Great to see someone thinks lie me . I also would like to know if this company will provide any help, customer support and is in the USA most importantly this system is not waterproof from what I can see I put my money on Finex 4200 mini controller made in the USA, they provide lighting equipment for fire, police and public safety
Thanks buddy for your vid but I’m still looking for quality waterproof system
Don your incredibly smart!! All your work is impressive 👏 your a great DIY! 👍 thanks for your time chatting with me too!
Happy to help Chad!
Just wanted to point out that there is also a firewall penetration on the pasenger side as well. Might be a little harder to access from inside the cab though depending on the size of your hands.
True! I used the passenger side one for my onboard compressor auxiliary circuit. Either route, I found them both difficult 😂
So, Don quick question, on the driver side, penetration can you give a little input how or what did you use to get it through the fire wall?
Don - loved the video and the step by step install directions. My AR-800 arrived yesterday and followed your video and the supplied installation brochure supplied by Auxbeam. Unfortunately, despite everything being hooked up correctly I cannot get the control box to turn on and illuminate. I tried to reach Auxbeam for assistance but to no avail, and they don't have any Q&A or Troubleshooting links on their website, or none that I could find.
My 2016 Toyota Tundra has LOW PROFILE mini fuses, so I used the supplied fuse tap, which is designed for mini fuses, and replaced my 10 amp low profile mini ignition fuse with a 10 amp mini fuse. The supplied fuse tap seems to fit fine into my truck's fuse box, and even with replacing the truck's 10 amp low profile mini fuse with a 10 amp mini fuse the truck started up just fine. I haven't hooked up any accessories yet, but one would conclude the control box should display it is receiving power with or without any attached accessories. Do you think the issue is using a fuse tap with mini fuses instead of LOW PROFILE mini fuses? Any troubleshooting ideas?
Sorry just saw this message. UA-cam flagged it as spam. Have you tried bridging the trigger wire to the main power lead just to test it out for power. That small trigger wire is on a two prong pin. Maybe the other side is live. Just making guesses in the dark
very good step by step explanation - question? the ignition/accessory switch wire - where would I connect it since I can't do your option where you spliced into a red wire? I have 2024 GMC Canyon elevation - please advise
Heated seats circuit? I used my cooled seats for these things
If you leave the light bar on in the switch panel and you turn off you engine and you turn on the engine back on the lights are on or you have to press the on button in the switch panel to turn them on again
If main power is cut from the panel, everything is off and has to be repressed. You can wire it up differently of course. After this video I added a wireless remote that can turn it on regardless if the truck is on or off too
Finally something cheaper than the switchPro
Nice option. I just had the OEM Up Fitter switches put in, but this looks like a cool option, too.
Thanks. I have both now! No shortage of switches 😂
Great video instruction. I see that you connect the remote wire to the ignition. Does that mean you can only turn lights on when the ignition is in "on" position? If so, is there a way to bypass that and give you the ability to turn the lights on without turning on the ignition?
This video should help:
Adding a Wireless Remote For My Accessories!
ua-cam.com/video/aV7ey5415dI/v-deo.html
Any sealant needed where you cut the rubber portion of the firewall?
Not really. I mean you could but the chances of water or dust getting in is highly unlikely
Thanks for taking the time to go through the app. Many videos and still no one has demonstrated the app as clearly as you have.
Is the app compatible with android auto? (Disregard, I now know you mean something like carlinkit.)
Im looking for a replacement to the CTS2 powerswitch.
to group lights do you have to have your phone hooked up all the time or will the control panel remember the group?
No need to use the app each time.
I would like to see the video from where you took the power with the ignition switch thanks
Since most of the viewers don’t have the same vehicle, I left it open ended for the ignition trigger. But I did make a video following up: ua-cam.com/video/aV7ey5415dI/v-deo.html
Good morning, For the wiring of the RC light bar. I notice u cap the red wire for the switch, at 14:29 of video {New Switch Panel Auxbeam AR-800} that being said..... you run the WHITE wire into the positive terminal using 30 amp location on AUX box and then the BLUE wire into positive terminal of next switch over ? Using the 30 amp switch right next to it ??? Lastly, do you connect the power leads that come with wiring harness for the light bar or just burying them ? Thanks Don J
Question. If the light bar has 2 color modes (amber and white) , would you need to wire them to separate switches? It looks like you did but wanted to confirm! Thank you. Great video looking to get one for my father in law
Yes I have each DRL to their own dedicated switch
What kind of compression is that that fits in that front quarter panel?
AirLift wireless compressor. I’ve made videos for the installation
Can you make a group that would turn on all of you lights and make them flash but the other buttons would be a normal setting of on and off?
I have the Chevy 1500. You used a existing fuse tap. Which fuse number would you recommend to tap into? Engine bay fuse number or passenger side fuse panel number?
Hi Thank you for the nice review Can I control the intensity of the lighting, make it dim or strong?
No problem. Thanks for watching. This product doesn’t allow you to adjust the brightness of the connected devices.
@@Donslife
Mmmm
Thanks 😊
First Purchase HERE
The cord was long enough. The only cutting of wires was my light bar switch
You should add dual roof ditch lights next!
🤔
Hi, Don. Excellent channel. I am interested in the AR-820, but do not wish to mount switches in the truck. I have a 2023 Canyon Denali, with Google built into the infotainment enter. Do you know if the app could be downloaded to the truck, and I could control my accessories with the screen?
Thanks
Not that I know of
So I'm wondering if I can cut the switch controls off and tap my DRL so they can work automatically? Then make everything automatic except things like light bars that are not for road use! Maybe i just need to find a way to split or separate the switch controls wire. Great videos keep up the great work!
I was looking to use this panel to run white/Amber pod lights. Would I be able to have 2 switches control each color of the light (set one to run solid white, the other strobe Amber). Would I have the jump the ground between the two switches? Thank you.
I have a newer light bar with amber and white DRL’s. They are hooked up to 3 switches. One for each color and the lightbar array itself. Works wonderfully. You should be able to run each positive wire to each individual switch too.
Hi sorry to bother you,
I have a 2022 gmc sierra at4 and purchased the smoked mirror lights with signal lights.
Came with no instructions and wondering where would be the best place to run the signal wire to. It's the light on the mirror face
I’m consider finding the fuse for each signal light and connect there with a fuse tap
@Donslife I was hopping to tap in the harness in the door if there was a wire for the signal, not sure if there is or not.
If not I would have to do it the way you said.
Thanks so much for getting back so fast and for your time
If I power off the vehicle “cutting power to accessory wire turning off the unit” if I turn my car back on without turning the switches off first will the buttons that were on. Will it come back on when you start? Or do you gotta turn them back on every time
The switch is designed to turn on and off with an ignition or accessory trigger. You would need to turn the connected device on again after the panel loses power. You can likely do some creative wiring outside of how the manufacturer instructs the installation. Going this route you can forgo using a switch altogether and just use a relay.
@@Donslife hold on I think we might not understand eachother, let’s say switch 1 is on currently, you turn off ur truck without turning off switch one. the device looses power, turn ur truck back on, will switch one also come back on or do you gotta press the button again.
@@uniteddrones7626 sorry! Shutting of the vehicle resets the panel to ‘off’ for all the the connected devices. You have to repress each item or group you have programmed to turn things back on.
Nice video 👍 If my light bar needs 35 amps (420W on 12V) and the switch panel only has up to 30 amps, how would i wire the original harness with a 40 amp relay into the auxbeam switch panel? Would that work? Thanks.
You would hook it up with 40amp harness/relay as per the lightbar manufacturer’s instructions and just use the Auxbeam as a switch. You could use a 5A circuit just for switching the 40amp relay on and off
@@Donslife Thank you loads. This is a big relief. 🙏
Great video and clean installation.
In regard to the compressor, how do you deflate/flate the tires pressure?
Without an auxiliary tank it is slow, but possible:
How to Install an Air Line in Your Truck!
ua-cam.com/video/RhqsI4NC2rU/v-deo.html
You have a compressor on your truck? Any video of the install?
Here’s one: How to Install a Wireless Compressor for your Air Suspension
ua-cam.com/video/pLCIiavqKtE/v-deo.html
Later on I add an auxiliary air line too
Is there an option to have the system turn an input on (light bar) when you start the truck instead of having to manually turn it on via the all or in-cab control?
Not on this model that I am aware of. If you wanted to do that, just hook up a relay as a trigger wire to your high beams
@@Donslife thanks, man!
Great Video! Thank You, with the RC Light that comes with three position switch, is it okay for the DRL and the flood to be on at the same time? is it really okay to eliminate relays and fuse holders and tap straight in with this unit? thanks
Thanks! I have looked into the flood light and DRL being on at the same time couldn't get a straight answer. The most of have learned is that it won't hurt it in the short term. The flood light drowns out the DRL too.
Each Auxbeam switch has it's own fused circuit and relay so yes, you can eliminate the ones that came with the light bar.
Please someone help been trying to find this information everywhere. I have auxbeam light bar that has a power button and a toggle button to switch from white amber both and stobe would this allow me to turn them on and switch in between the different modes? Thanks
It would have to have each feature (wire) hooked up to separate switches on the Auxbeam panel instead of using the switch it came with. Then you would program each switch to behave how you want it to (on/off, momentary or strobe)
@Donslife would I be able to switch in between the different color modes I don't know if I explained it right. Have a switch with 2 buttons one is on/off the other switches in between white, amber, white and amber then white stobe
Amber strobe and white and amber strobe. Thanks for ur info and time.
With the Auxbeam you could do all of those modes separately
Thanks for this video, great install and demo, definitely a good investment to slowly add accessories to your vehicle, gonna do this on my 4R.
It has been a great solution for me so far. Filled up 7/8 spots!
@@Donslife can you list all of those 7 items? Just to see the possibilities?
Light Bar
Light Bar DRL (White)
Light Bar DRL (Amber)
Rock Lights
On Board Compressor
Pod Lights
Interior ambient LED lighting
Videos for all of these on the channel
Ah Don. I was waiting for you to visually show me mounting options inside the cab. Anyhow, I just bought one using the code. Originally $300, Auxbeam is currently already 10% off at $269. With your code it gets down to $243.
I only found the one spot that wouldn’t involve screws or cutting
You may have answered this, but I have a 3 way switch for light. On/off/backlit. Will this panel allow for all 3 positions?
Not that I am aware of. A 3rd position would need a 2nd switch to be used.
Just curious 🤔 if you can have constant power to the panel since you can shut off the lights anyway? More or less if you're at a car show, that you're not having your acc,on
Yes you can. You’ll just drain your battery a little more quickly depending on what you have running as well as the backlight for the switch
I added a remote switch : Adding a Wireless Remote For My Accessories!
ua-cam.com/video/aV7ey5415dI/v-deo.html
So, theoretically, would I be able to run this purely from my phone without installing the switch panel? I'm looking at getting these for my RHD Jeep so I can finally get some strobes on it, but not super keen on the idea of tearing the dash apart to run the wires.
Great video, super informative!
Great vid. Do you know the power the panel uses to operate itself? Like standby power when all the circuits are turned on but no accessories actually drawing power? I have a different panel that draws 1a constantly just to have switches in on position.It’s a bit of an issue and I need to find new panel. Thanks
Awesome job, can you turn on the lights with the app even if the truck is turned off?
Yes if you wire it up that way. Here is a video where I can turn it on remotely too:
Adding a Wireless Remote For My Accessories!
ua-cam.com/video/aV7ey5415dI/v-deo.html
Any chance you could make a reel or shorts about which accessory you have in which slot?
My Community page here on UA-cam and my Instagram both have a picture with labels that can help you out
If I have lights that I would like functioning while the ignition is off, does this switch Bank drain the battery if the accessory wire is hooked up to a power source that isn't ignition dependent?
It will drain a little power to illuminate the LED backlights for the panel if the remote wire is connected to an ‘always hot’ source. I left my panel powered up overnight and my vehicle wasn’t really drained. Over a few days it could be a problem. You might want to do something like this : ua-cam.com/video/aV7ey5415dI/v-deo.html
Can you turn the pod light on without the ignition on or no? And if yes, how do you wire where the pod light can turn on without the ignition being on and would it drain battery? Thank you
Yes there is a way. Here is one way that I did it :
Adding a Wireless Remote For My Accessories!
ua-cam.com/video/aV7ey5415dI/v-deo.html
You still need to have the actual controller hooked up to use the app though?
Correct. The App communicates with the controller via Bluetooth.
Great video. I have a question. Can it be operated via Bluetooth with the ignition off? I camp in the middle of nowhere and if something is stirring around camp I would like to be able to "Light up the night". Thanks
Yes if you wire the panel to be live with the ignition off
@@Donslife do you know if it has any amperage draw that way? With all accessories off, of course. Thanks for the quick reply.
You can add a remote turn on like I did
Adding a Wireless Remote For My Accessories!
ua-cam.com/video/aV7ey5415dI/v-deo.html
This way I can turn the panel on from 20ft away and connect my bluetooth to operate anything
Can you dim the light bars and stuff with the app also like the trigger controller?
No you can’t with this switch.
great video, have a question.. I install the one thats not compatible with the app. if i get the one with the APP do i have to chasnge just the control pannel?
Good question, as far as I know the control panel that goes in the vehicle is what ‘talks’ to the app. So as long as the switch box is compatible with a Bluetooth capable panel at a later time, I think it would work. I would ask Auxbeam to be sure just in case the physical connections vary. To be fair, I only installed the one panel and haven’t had experience with their other switches/panels
It worked with just the controller. Thanks for responding tho
Wish you would’ve shown were the wire comes through under the dash!
There are two circular grommets on the firewall. One on the driver’s side and passenger side. They are made out of rubber and need the end cut open to pass wires through. That’s what they are there for. In some of my videos I show them
Hey Don. Betcha that truck will soon be able to make coffee in the AM before too long with all your DIY mods! Hahhaa...nice work (as always)
Great idea 💡!
We'll done video. Great production value
Hi, thanks for the tutorial. What's the name of that light bar that you show on your truck?
No Problem. I had a 20” Rough Country with DRL but now I have upgraded it to a Strands Siberia 22” lightbar. I have videos for both
@@Donslife great, thanks 👍
If you forget to turn the lights off does this automatically turn them off after shutting the truck off?
Yes, when the truck is turned off the panel will lose power too and shut off all accessories connected to it. I chose to wire it up this way. In a later video, I added a remote to be able to turn the panel on and off independently of the truck.
Adding a Wireless Remote For My Accessories!
ua-cam.com/video/aV7ey5415dI/v-deo.html
Are you able to customize the pulse pattern? Or is it always the same?
This species unit allows the one speed for pulse on each switch
thanks!@@Donslife
Do both units do the strobing or just the one with the Bluetooth ?
Some non-Bluetooth models have the feature. Look for ‘pulse’ as an available function
What was the noise when you made the light strobe?
Without rewatching the video, probably the relays clicking on/off rapidly
How is that motherboard? Much taller than regular 8 gang? Thanks
I am leaning towards Auxbeam > more expensive options but I don't like that I have to turn my IGN on to power up my accessories. Is the app control also dependent on IGN being on?
Fair point. You can wire up the switch panel to constant too. Really up to you…….or you can add a diode and a remote switch like I did in the video. Now I can sit by the campfire and turn the switch on remotely, while controlling all the gadgets. (For example) 😊
Adding a Wireless Remote For My Accessories!
ua-cam.com/video/aV7ey5415dI/v-deo.html
Does the car have to be on in order to use the app? Would be cool to turn on lightbars from the rooftop tent if need be.
No, you can install a remote switch like I did in this video if you wanted:
Adding a Wireless Remote For My Accessories!
ua-cam.com/video/aV7ey5415dI/v-deo.html
@@Donslife thanks! 🙏
The light strip had 3 cables, how did you connect it?
I replied to your instagram message 😊
I just got to the part of the video where you said you have a compressor under your hood? I know I didn’t hear that wrong because I even ruined it in. Heard it again, lol. Do you have a video showing the install of your compressor?
There are a couple related to it. Here is the main one :
How to Install a Wireless Compressor for your Air Suspension
ua-cam.com/video/pLCIiavqKtE/v-deo.html
And another:
How to Install an Air Line in Your Truck!
ua-cam.com/video/RhqsI4NC2rU/v-deo.html
Thank you for the quick reply. What did you do with the negative and/or ground? Did you just have to run it to one of the switches?
You can terminate them on the body/frame or the switch
Those with a 2022 or so GMC AT4 where did you connect the fuse tap wire to an ignition source?
Passenger side fuse box has more options. The cooled seats is the one I used. Not sure the location on the 22’s
Hey Don, love all your vids and mods. Will this work just off the auxbeam phone app or infotainment screen without having to run the 8gang controller into the cab?
Thank you sir! Technically you could leave the control panel tucked away somewhere safely in the engine bay away from heat and moisture. Your phone app via Bluetooth would do the controlling. Personally I would find that inconvenient and would want the panel in the cab, even if you left it sitting in the glovebox or something. If you want to control it with your infotainment system, you’ll need something like my CarPlay AI box to control the Auxbeam switches.
Do it have any trigger inpputs?
Like hight beam signal = turn on switch 1 and 2 ect.
I think I liike the Switch Pros better.
I get it but this is 1/3 the price is all
Great stuff thanks 👍 you said you were going to up a different light bar Which new light bar you going with ✌️🇨🇦
I am thinking the Strand 22” dual row with DRL. I haven’t ordered it yet, but I think that’s the one
I am loving this control panel.
One question. Does anyone if it is possible to set the control to power on the last set accessories as soon as it powers up with the car?
As it stands now, when you turn the car off, powering off the panel, next time you power the car on, you must press the main power button on the panel to activate it.
I would like to set it to power on automatically with the car startup.
Is this possible?
A+ work as always! If mine wasnt a lease id consider doing alot of your mods. Have you considered installing the sierra sportsbar from the 16-19 all-terrains? I swapped mine over but on the x-31 package not the at4. Ive had many compliments and would def look good on the artic white!
What is this sportsbar you speak of? I have the same truck
Gm had a factory sportsbar they offered on the 16-19 all-terrainX packages. I kept mine when i sold the truck and put it on my next one which was the '21 new body style.
I have thought about a couple sport bars including the one you speak of. With my current box cover I just can do it. But I haven’t ruled it out
Box cover definitely wont work. I had to do a bit of modding to the tonneau cover to make things fit right. The factory covers will not fit either. Only certain aftermarket ones will work.
This look identical to the non rgb non app version. I'm thinking maybe all that functionality is built into the switch itself. My biggest dislike is that it doesn't remember what's on when I turn the car back on. So DRL would be pointless to wire up since they'd have to be turned on every time. I actually mounted my switch to my GMRS radio's mount underneath it so it's kinda like a console of equipment. Love the auto dim feature, works very well. Hopefully this will hold up better than the junk wiring harnesses KC sent me with my lights. Corroded and burned at the relay since it was 1 wire in and 2 out to each 80 watt light. The outputs were fine but the input wire was just burnt.
Are you able to set anything to turn on with the ignition? ie DRL always on unless you switch it off?
Yes it could be done but more wiring would be involved.
@@Donslife I was thinking of wiring in a normally closed relay and using the switch to turn it off. But was hoping maybe it could be an option in the upgraded one to just be normally closed vs open. Thanks
Exactly my first thought. If you do it, let me know how you like it that way
Hey Don, a little curious when you are speaking about the "App" and choosing the Colors. Are the Colors associated to the Buttons on the App or colors coming out of your Lightbar?
Strictly the look of the panel buttons can be changed with the APP
@@Donslife Thank you, Sir. Great Videos and modifications. Must be nice to be rich! Ha, Ha, Ha........
Can you dimmable LED strips with this? I want to install LEDs inside my camper and be able to dimmable them also. Is this possible with this switch?
Hi there, the switch won’t control a dimming function. The light strip itself would need to have a dimming feature that you’d have to adjust with it’s own app or mechanical knob/slider.
Which fuse was your pink wire going to? I am not sure which fuse to connect to on my 22 sierra.
I ran it to the ventilated seat fuse on the passenger side panel inside the cab
@@Donslife This is the biggest question I have as well. I looked and a few others, and they also have this question, but I, unfortunately, don't understand your responses. I do think I understand that it's your pink wire in this video. I went to the compressor video but could not find exactly what you did here. Is there another wire or anything anywhere closer or easier to find? or do you have a video clip of this? Thanks so much for all the videos. Just used a ton of your discount codes so thank you!
I noticed you didn’t touch the brightness in the middle. Is the brightness for the panel or for the lights you’re turning on/off on the light bar?
Brightness is for the panel, which also has an ambient light sensor to adjust itself
gotcha, but to confirm no way to dim the actual lights outside of the vehicle? I have Baja S2s on my roof rack, but at night camping it would be nice to dim them from being too bright
@@jeromefronda252 unfortunately this panel only does switching, no dimming. Be careful too, not all lighting will allow dimming.
Great video, this honestly sold me on it.
It made sense for me and has been working well
Nice video! Does the controller lose memory of the switches that were on after an ignition cycle from on to off to on again? Engine cooling fan for example should have immediate power without having to turn a switch on each time you start the vehicle. Thanks in advance
When the ignition is turned off the devices it controls turn off too. When the first ignition is on again, the devices need to be turned back on manually but they will stay programmed as groups and/or pulse, toggle and momentarily mode if you set them up that way. I installed a remote control circuit with a diode so I can keep the switch on without starting the truck too.
@@Donslife Could you do a video on that setup? I am wanting to have power without the truck being on but still want to have safeguards in place.
Done : Adding a Wireless Remote For My Accessories!
ua-cam.com/video/aV7ey5415dI/v-deo.html
What sort of range do you get on the app and phone use??
Normal Bluetooth range, like 10-30ft. They make a RF remote version too now
Great walk thru, appreciate it!
Absolutely 👍🏼 Glad you like it
Hey Don what fuse do I use for my acc I have the same truck
Try the cooled/ventilated seats on the passenger side interior fuse panel
Why did you put a blank wire end on one of the three wires where you cut off the connector? Was the wire you blanked the illumination wire for the switch that normally connects to that lead?
Yes I believe so
Do you know if you are able to swap out the fuses to higher amp? Or is 30 max? Thanks for the great video
I am not sure. My assumption would be each circuit is up to 30Amp but don’t exceed 60Amps total running at the same time. You’d have to ask the manufacturer if you can go higher than 30amps on one circuit
Bro can you confirm that the auxbeam panel is defect. A lot of people on UA-cam telling that after a month of use the box is damaged making some equipment on all the time. Replaced by auxbeam but the issue persists.
Mine works perfectly. I was just using it at a car show and had my lights on a strobe effect using the Bluetooth app on my phone. I have not had any issues at all
What’s your next lighting install now?
Maybe the Strand. Any other suggestions…I have some ideas
Underglow kit!! But it has to light the entire area under the truck and hiding the lights is the key! I hated seeing the neon and led strips.... took away the whole effect. Bright white to match the light bar and running lights. All other colors optional lol
@@Juddmann007 I have been looking. I also do prefer the glow and not being able to see the bulbs. So much junk out there, I have been having trouble finding some that look like they’ll survive 4 seasons.
I ran a set of streetglow neons back in highschool but on a car. Not sure if they are still around or even make neon tubes anymore. They held up through several winters and were brighter than any led strips ive seen
I'd like to see ditch lights!!
Hey Don
With the ignition cable… where would you put that for somebody who doesn’t have a compressor? Lol
Cooled seat fuse tap on the passenger side of my Sierra. Any ignition switched fuse will work. The current draw is minimal
@@Donslife thank you man 🤙🏼
Gained another subscription! I would be interested in knowing if the Ar-800 is still performing well after a few months now.
Welcome! It absolutely is. I just wired up some more lighting in this video last week!
ua-cam.com/video/SChkEK-RlUE/v-deo.html
How did you end up mounting the panel? Adhesive or screws/cutout? Was unclear
3M adhesive strips on the flat area of my dash.
Whats your thoughts on garmin powerswitch?
Soo I have RC lights that have a full light mode and a DRL mode. Will that still work with this panel?
Yes, just wire each feature to a switch. You can also program switches to turn on together
@@Donslife thank you
Really smart, like got both standards buttons or the Bluetooth.
Nice one thanks
I also like the dual functionality
Great video! Quick question though. How do you connect to the app? I've been struggling.
It works fine for me. Restart your phone and if that doesn’t work delete the app and try reinstall it?
Great video, and detailed installation vide. Let me comment that AuxBeam switch panel are crappy products, and customer service is terrible I install AuxBeam switch panel AR-800 according to included brochure, and only lasted 3 days, and I had to fight hard with customer service department to get my refund, I do not recomend this product at all!!!!!
Sorry about your experience. Mine has been consistent and reliable. I have 7/8 switches being used currently.
Did you ask Auxbeam if this controller is waterproof system ip67 rated ? What about customer services to take my phone calls if there’s any issues with this 6 or 8 gang controller
Every switch has its waterproof rating listed on the website. I have always had replies 📧 mg them. Never have I attempted a phone call
Don, great work, Gained a subscriber! I'm curious if you know, I reached out to Auxbeam asking if you always had to turn the switch on (for a specific device i.e. DRL, clearance lights etc) with each power up? They replied with, you will always need to turn the unit on via the on/off button on the control head or thru app once you have either key in ACC or ignition on. Is that true? Does each button have memory of previous use at power off? However, I also wanted to be able to have the unit automatically turn on with ACC or ignition and have the preset lights come on. Trying to eliminate always having to turn the unit on after keying up the vehicle to turn on my DRL and clearance lights each time I start the vehicle. Thanks!
I have exactly the same question about the memory function...
@@robertionescu_ I did get this unit and although it powers up (the buttons light up) if using the accessory lead. Then you can either hit the "memory button" in the center of the unit to turn on any switches/buttons that were on when you previously cut power to the unit or, select which button(s) you wish to turn on individually. It will not power on any items connected to the buttons by default when turning the key on. hope this helps.
@@davymill6696 Thank you. This helps a lot 👍
hope you see this but how did you mount the pod on the dash?
Double sided tape (good quality) used on emblems