Very helpful video. My Ranger only has 600 hrs on it but the u- joints were making noise and needed changed. Your method worked well and and saved dismantling the front end and taking the diff out. Thanks !
I just knocked the pin out, removed the bumper/ brush gard, four bolt on front diff and slid it out the front. Also used an air chisel with 5/16 punch bit.
Sweet..im betting the ujoints are going out and causing the splines to go bad after. thoughts on a rubber O ring on the front diff shaft before sliding the prop back on?
Not sure about putting an o-ring on the front shaft, there is no Groove for it to sit in. The last couple I have done the splines have stayed tight on the front yokes (rusted in) and the U-joints still ended up failing as normal. I have been able to extend the life of the rear prop shaft splined yoke by siliconing around the end of the Yoke to keep dirt and water from entering. Its helped alot.
i wonder why polaris doesn't go to a cv joint on their drive shafts. i don't know how many rear drive shafts I've replaced on dad's polaris four wheelers for that exact same reason, worn u joints and bad splines. the slop got so bad on the rear diff that i had to replace the whole thing, it just gets rust and dirt in there and wears itself out. pretty nice winter we're having.
Hi. Nice video. Where did you buy this item and how big is this peace? I trying to get one for my Ranger 570 midsize but this is so confuse. Alot different information. Can you please help me on this information?
There is about 6500 miles and 900 hours on this unit now. The other two 570s have between 600 and 800 hours, probably between 4500 and 6000 miles on them. We bought three of these 570s at the same time a year back. They were on rebate and we were able to reuse our 800 cabs on these models. so far these have been good machines, simple to service good on fuel and easy to repair. So far all three have needed a drive clutch and prop shaft at about the same miles an hours. The clutch would have lasted much longer if Polaris had put the intake for the CVT box up front like they used to. Instead they move the intake behind the seat where it picks up a lot more dust than it should
I'm really glad I watched this video, saved me a bunch of dismantling.Thanks.
Very helpful video. My Ranger only has 600 hrs on it but the u- joints were making noise and needed changed. Your method worked well and and saved dismantling the front end and taking the diff out. Thanks !
Thanks for the good info. Was going to remove the front diff. Saved a lot of time. The part # info was invaluable too.
Great instructive video! We followed it fully and the job went exactly as you described. Thanks!!!
I just knocked the pin out, removed the bumper/ brush gard, four bolt on front diff and slid it out the front. Also used an air chisel with 5/16 punch bit.
Buddy you're the best!
Great video TKS, Mine was a mid size 2016 570 an it did great!!
Thanks for showing us how you got the pin out that’s the only problem I’m having
Thanks for sharing. Great instructional video.
Sweet..im betting the ujoints are going out and causing the splines to go bad after. thoughts on a rubber O ring on the front diff shaft before sliding the prop back on?
Not sure about putting an o-ring on the front shaft, there is no Groove for it to sit in. The last couple I have done the splines have stayed tight on the front yokes (rusted in) and the U-joints still ended up failing as normal. I have been able to extend the life of the rear prop shaft splined yoke by siliconing around the end of the Yoke to keep dirt and water from entering. Its helped alot.
Considering using a bicycle tube stretched over the joint and a couple of zip ties.after I fill it full of grease!
i wonder why polaris doesn't go to a cv joint on their drive shafts. i don't know how many rear drive shafts I've replaced on dad's polaris four wheelers for that exact same reason, worn u joints and bad splines. the slop got so bad on the rear diff that i had to replace the whole thing, it just gets rust and dirt in there and wears itself out. pretty nice winter we're having.
THANK YOU!!! it worked great.
Hi.
Nice video. Where did you buy this item and how big is this peace? I trying to get one for my Ranger 570 midsize but this is so confuse. Alot different information. Can you please help me on this information?
I ordered mine from superatv it’s called a front propshaft for a reg cab Polaris . It’s prob 4 feet long approx . It ain’t cheap
Mine is 2015 same problem but for your viewers drop plastic bottom shield slide back loosen 4 mount bolts on front diff . Comes out bottom
They are not fun
Where did you find the driveshaft? Can you post a link! Thanks
It's a polaris driveline
Where did you order this prop shaft from?
Very good
How many miles do you have on it and how many 570 do you have
There is about 6500 miles and 900 hours on this unit now. The other two 570s have between 600 and 800 hours, probably between 4500 and 6000 miles on them. We bought three of these 570s at the same time a year back. They were on rebate and we were able to reuse our 800 cabs on these models. so far these have been good machines, simple to service good on fuel and easy to repair. So far all three have needed a drive clutch and prop shaft at about the same miles an hours. The clutch would have lasted much longer if Polaris had put the intake for the CVT box up front like they used to. Instead they move the intake behind the seat where it picks up a lot more dust than it should
But ranger has a 2 inch lift
Ive brought mine in 2 times for broke u joints . Polaris sucks and don't fix things right.