I have to give you a huge thank you, you saved my ass. I followed your instructions and everything worked except the motor would stop when I let go of the button. I noticed you were using momentary switches like mine so I re-watched your video and realised I had forgotten to program the PO-11, so I did that and it all works perfectly now. I’m so happy. Now I switch a big master switch and the VFD turns on and the original power lamp on the front of the lathe lights up to let me know there is power to the lathe. The original on / off switches also work too so it’s hard to tell there is even a VFD there. Thank you so much for your easy to follow and well explained video. Cheers mate, Stuart 🇦🇺
I thought i had it figured out but the programing far is what i couldn't get right. Even though the VFD stats rpm or hz i change it to. When i adjust it, the speed never changed on motor. I hate these kind of vfd where the programing is very hard to understand and get right
Not this model but a cheap VEVOR one , I did exactly what you said. Potentiometer for changing speed’s. But programming and understanding/fluking the pin out and setup to get it working. Can be done though
I have to give you a huge thank you, you saved my ass. I followed your instructions and everything worked except the motor would stop when I let go of the button. I noticed you were using momentary switches like mine so I re-watched your video and realised I had forgotten to program the PO-11, so I did that and it all works perfectly now. I’m so happy. Now I switch a big master switch and the VFD turns on and the original power lamp on the front of the lathe lights up to let me know there is power to the lathe. The original on / off switches also work too so it’s hard to tell there is even a VFD there. Thank you so much for your easy to follow and well explained video. Cheers mate, Stuart 🇦🇺
Thank you for explaining this setup. It has helped me a lot. 👍
You are an amazing teacher! Thank you
Thank you the explanation is clear sir.
Amazing video. Thanks a lot for the info; it was crystal clear!
Many thanks for your useful information and good videos
Thanks for knowgable video sharing.
Very well explained
Thank you very much sir!
Very well explained.
super sir pls tell about 24 volt what is the purpose
நன்றி.
thank you nice video keep it up
You are a great teacher
Thank you! The RUN button is NO and STOP button is NC
Hi i have a motor from eurodrive and this is 3 phase i already put the plates in the motor to Delta do i only need to install it on the VFD then?
Helpful video
hi sir in an application with start stop of 3 phase motor what is the best way to connect it so the motoer is not hot
the triangle or the star ?
super explanation, but one thing i m not clear, how do you know if is three wire control or two? thx!
Single phase connection running 3 phase Gear Motor possible please reply
Great explain sir
good job
Hi! You use the NC or NO for both start and finish?
Good job
Good one
Thanks . can you please make available the circuit diagram
Is there Any recommended speed for a 3 face motor for a York Pack unit ?
Hi, Can i know the output of motor is in star or delta
Please do one with a outside rehestat along with a push button to start.
How about using potentiometer to regulate speed of motor?
I thought i had it figured out but the programing far is what i couldn't get right. Even though the VFD stats rpm or hz i change it to. When i adjust it, the speed never changed on motor. I hate these kind of vfd where the programing is very hard to understand and get right
Not this model but a cheap VEVOR one , I did exactly what you said. Potentiometer for changing speed’s.
But programming and understanding/fluking the pin out and setup to get it working.
Can be done though
Hello sir your video is very helpfull sir may i ask how many KW of vfd i need to use my 3phase motor 220v 2.5hp and 220v supply thank you
you will have a label but if you are telling 2.5hp i think above 1.5kw so 2.2kw will be enough for you
Jak wyświetlić na tym wyświetlaczu obroty w jednostkach rpm zamiast Hz
Thanks
Good videos
Thank
How many hp does a vfd can operate? Is this applicable to large motors?
can you pls explain the same on/off control with only one 24V PNP proximity sensor?
what is ratting of this vfd..
Can you help me to display a rpm ?????? Thanks in advance
How can I use Dc to control a 3 phase induction motor?
Super
Nice
it need a wiring diagram for a beginner to understand
One comment:
Start button should be NO (normally open).
Stop button should be NC (normally closed).
Help me to programing the vfd
What is v f d in electrical
How to reset alll settings.. i think i mess up
Where is the overload relay?
Anna siemens tell me
❤
Bro Ths MFD prise ?
Share the link for two wire connection
He did. It’s at the bottom of the description.
Sabina Falls
Oh you dont say torque of the motor depends on magnetic field density and current , and speed depends on the frequency . You dont say .
Waters Knolls
Ratke Hills
Where’s the input voltage earth???
Zieme Lights
Lucy Fields
Where are the earth's?
Hane Path
Runte Circle
Jayce Station
Mitchel Path
Grant Streets
Althea Creek
Cummings Village
Cordia Road
Brennan Centers
Cummerata Expressway
West Fort
Braun Summit
Rowe Valleys
Upton Views
Kris Station
Abshire Drives
Wunsch River
Jessie Dale
Fannie Turnpike
Emard Valleys
Oran Junction
Speak in to Urdu & hindi
Hey electrical guy, I had a technician wire my 4kw inverter to a toilet paper but when I put speed on 1.5 the machine runs too fast
Hindi in
watch on this channel www.youtube.com/@ElectricalTechnician
4493 Jerel Plains
81986 Graciela Street
74477 Fredy Loaf