Put Aluminum Foil on Led Bulb Brightness Will Increase 100%
Вставка
- Опубліковано 6 лют 2023
- Led bulb repair can be done at home with simple methods. You can repair led bulbs with very simple tools such as graphite and aluminum foil. LED bulbs can break down when they get too hot. You can fix these led bulbs at home instead of throwing them away. Aluminum foil and pencil methods are effective in repairing led bulbs. Don't waste money on a new led lamp using these methods.
- Навчання та стиль
New generation clickbait
As u clicked lmao
No! Thats legit i already try that
Thanks for the alert. Didn’t watch.
Do the smart thing and use solder. The graphite will cause resistance heating. The alunium foil will break down and possibly catch fire.
~ Which goes to prove that "a little knowledge is a dangerous thing".
@@gweedomurray9923 awesomely said
@@sumitabhbishoyi6666 ~ Sadly so, Sumitabh Bishoyi . Thank you.
Do the smart thing and don't be a cheap ass, go buy a new $2 bulb ...
I was wondering if it was graphite or a special pencil for electricity. So many things could I theorize be added to the pencil making it electrically conductive.
This is pretty unsafe. Led Bulbs do in fact get pretty warm. The normal heating and cooling cycles when used will break down the adhesive of the tape and it could lift, weakening the aluminum's connection. Now what you have is a small pocket of hot air with kindling (the paper) and an ignition source, the electric arc from a barely touching tinfoil connection. Surrounded by plastic which is most likely flammable. Fire takes 3 things: Heat, Fuel, Oxygen. (a spark creates enough heat to start the process). The graphite seems better, but not much... for the same reasons. Solder it!
that was also my first tought the carbon pen trick maby good , the foil trick unsave, soldering the best
The load will increase on the rest of the remaining worms, and they will burn one after the other... It is a temporary and non-permanent solution... Thank you..
Стабилизатор тока там стоит, нагрузка только на нём возрастёт, но не на светодиодах.
It's normally they are using constant current circuit on the led bulb, so no, you are wrong
temporary and non-permanent both have the same meaning.
EDIT: this comment is wrong, the one below it is correct
@@willtj1787 the same amount of current will split up between less LEDs, meaning each one will get more
@@HolarMusic No, the LEDs are wired in series meaning the same current runs through all the LEDs. That's why the entire bulb quit when one LED failed, the circuit was broken. What will actually happen is since the LED driver is designed to put out a fixed amount of current the voltage output will drop since there is one less LED to push that current through.
Никогда не лезьте во включённую лампу неизолированным инструментом - Вас может запросто убить электричеством, хоть напряжение на одном светодиоде и невелико, но так как источник питания в лампе не имеет галванической развязки от сети 220В, то Вы можете попасть под потенциал сети.
Aaaaaaaahhhhh!!!
Run!!!!!!
But removing one or more LEDs will increase the current in the electrical circuit, which will soon cause other LEDs and other components to burn out. The correct thing is, if you need an LED lamp with more brightness, buy another one with greater power.
Só que retirando um ou mais leds ira aumentar a corrente do circuito elétrico, que logo mais vai causar a queima de outros leds como também de outros componentes. O correto é, se necessita de uma lampada led com mais luminosidade é comprar outra de maior potencia.
Have you heard about constant current circuit?led bulb generally use constant current circuit. So no you are wrong
@@willtj1787 since the LEDs are connected in series, the same amount of current will split up between less LEDs, meaning each one will get more than it should
use a resistor or they will blow even quicker as they are in series. When he says increase brightness by 100% it's because they go from not working to working lol. Use a resistor or another led. Problem is the heat sink it's not easy to get enough heat into the board to solder them due to the built in heat sink or ground plane.
The scares on the left hand of this dude indicate where his way of solving problems leads. I am surprised that he still has both hands.
OK. This might technically work. But be aware that depending on the lamp design you may risk to get an electrical shock that may kill you! This should only be done by people that are aware of the danger working with electricity.
If you ever do it it would be better to replace the burnt out LED by one of the same type. And even though I like the idea to save money and produce less waste it might be better to spent $2 for a new lamp. That's much more environmental friendly than a burning house!
yeah this might be safe on low voltage instalations like those ~40v cables, otherwise it's a bad idea!
Smart people will just buy a brighter bulb instead of rigging a low led bulb.
i find that sticking a fork into the socket also works well.
Be careful when commenting stuff like this coz some people without any knowledge/ kids will try this
@@TRAZExYTYes. For any mentally impaired people or children: Don't do this.
It's a joke and very dangerous in reality.
It s like telling people they can learn to fly by jumping from a bridge...
For the brightest effect, the foil should be wrapped all over the screw of the bulb
🤣
Hahaha
@@blackknight9558Don't forget to have a little bit of thermite
This is a joke
I've been getting my LED bulbs to work again the same way. I got the idea from the Christmas lights that failed in the same way back in the day😅. Leave the cap off so they don't overheat tell everyone to keep their friggin hands away from them. They all still work many years later.😮 No problem I'm just getting my money's worth😂.
use a resistor or they will blow even quicker as they are in series. When he says increase brightness by 100% it's because they go from not working to working lol. Use a resistor or another led. Problem is the heat sink it's not easy to get enough heat into the board to solder them due to the built in heat sink or ground plane.
والله انك شخص راءع سيدي شكرا لك
Видео неправильного ремонта. Правильно это надо паяльником припаивать новый светодиод
Зачем новый,что есть то дочтаточно...
@@I.X.Y.18 быстро перегорит, потому что будет больше тока на меньшее количество светодиодов, если тупо один выкинуть
Hot damn! I just this minute tried it and it works completely. But I think I'll go the way of solder instead of the foil. THANK YOU FOR THIS FIX!!!
use a resistor or they will blow even quicker as they are in series.
Harmful video, nice time catching fire. 👍
This looks completely safe…
The rubber tape will melt and fall off. The current through the remaining LEDs will increase and the will burn out.
Ток не увеличится.
bad tapes will. 3M Scotch TM won't.
Человечество давно создало паяльник. 😊
Синяя изолента - это то что надо!
Every light has it's unique look n rich lighting
doesnt make the bulb brighter... this is just a how to fix a broken led lightbulb. smh
And you are being very generous with the word "fix" . Kludge, bodge, rig, and other more appropriate words come to mind.
Good video, but misleading thumbnail
You will get a free light show if you screw a ball of foil into the light socket.
Dumb people: if you havent burned your house down yet, dont try this its a joke.
С синей изолентой можно было даже фольгу не подкладывать. С синей изолентой все работает! 😂😂😂
你要用鉛筆的鉛來做 導電目標 久了也是會因高溫而脫落(用錫箔紙亦同)，用錫焊接不是更好!最好的方式還是買相同 燈珠 做更換壽命才長，要不然其他 燈珠 受電增加，整體燈珠壽命也會跟著縮短~
Die idee ist Wortwörtlich der Burner 😂
Cool wie man einen Wiederstand vom Hersteller überbrückt . Mit glück reduziert es die Lebensdauer mit Pech auch die vom Bastler 😂
Most definitely
Yep well said.
olá bom dia parabéns gostei muito Eusou Antônio de viçosa Minas Gerais
I felt the same way when initially seeing this actually played out. However, now I feel I may have been mislead to some degree. But why, what is the end game? What do they want? Who is "they"?
Mas gostam de aparecer... faltou colocar o RG e CPF...
This just means they are going to blow even quicker. If you are going to try it this way put a resistor in.
Hope everyone is doing good and staying safe
Graphite increase conductivity with increased heat. Eventually your house could burn down.
To add radiating aluminium particles are the biggest cause of cancer. Please research further.. also can correct me if I'm wrong. Thank you..
You are wrong.
taka naprawa wystarcza maksymalnie na miesiąc
po napprawie swieci jasniej bo w szeregu diod jednej już nie ma, więc napięcie rozkłada się na pozostałe, ale są one wtedy jakby przeVoltowane, więc ich zywotność maleje . To jjuż lepiej wlutować tam nową diodę
LED칩을 교체하고 납땜 할거라 생각했더니 그냥 포기하고 은박으로 붙였네요. 잘했습니다.
Bravo..bravo..BRAVISSIMO😂 CIAO
Nice work. Thanks.
The thumbnail😅😂😂😂
THIS ISNT HOW TO MAKE THEM BRIGHTER THIS IS HOW TO FIX BROKEN LEDS
I'll just go with a higher lumen bulb for an extra couple of bucks.
Awesome idea to cause fire
The LED connection is in series if are going to short the busted LED the good LED will overload. Correct me if i'm wrong
Correct, better bro solder led or resistance on it. This trick will not last more than a few weeks.
Correct
CESAR bro you are wrong.. As the current remains same in series, other LEDs won't be overloaded. This is DOB circuit. Trust me, I am an engineer.
@@DEEPAKSINGH02041992 nope, you are tech support
You are right . After all the main flow cannot be checked when the circuit in the led bulb is tampered . It’s just like reigniting the filament bulb when the tungsten matter draws more electricity . For example a tungsten bulb when the loosened filament burns 4 times brighter than its original power.
it's not a good solution, because this way the other leds have a higher voltage and thus the others will be destroyed sooner.
KORREKT !
Incorrect i did this procedure on 2 led lights about 6 moths ago and they still work fine
@@teammouse add that more
LED is very sensitive to current...
.
The driver is a constant current limiter so the remaining LEDs should be fine
Wow pencil
Dont mess with live socket voltage
It's not 100% brighter if you remove one of the COB elements 😅
why not just replace the led?
that is indeed the best , i have done it and the now keeps on working for many hours but it is very very fiddly job with these smd leds and normal solder station.
А если убрать два светодиода то яркость увеличится в 200 раз? А если три? 🤯 А для увеличения яркости если нужно то можно просто снять колпак.
пффф, я только 3 оставил и лампа весь город освещает! по плану - вообще все убрать и вместо солнца использовать!🤣
ну, а если серьёзно - автор ролика явно долба.б
Чем больше закарачиваешь перегоревших светодиодов тем лампа светит хуже ,а не ярче как вы тут пишите.Говно оно и есть говно,в Китае это стоит копейки ,а у нас дерут деньги .Вчера сын купил на алике лампы с прозрачной колбой и из 10 штук одна не исправна,моргает как паралитик и ни где ни чего не подрегулируешь.Только в мусорку.
@@user-pb3cb3eh3l yeah damn skippy!!!
@@user-pb3cb3eh3l это к нанооленеводу))... оно тут же высрет супермегонано-заводик...из могил поднимет конструкторов и инженеров... эх, заживём))))))
Ой! Фсё! Я сразу при покупке закорачиваю ВСЕ светодиоды! Теперь у нас в селе каждый день солнечный!!! светит на 100500 ярче солнца! Вот так то!!!
😮 wow 😳
👍👏👌
Why is it he tested in the 3rd outlet, passed about and didn't put it back in the same outlet 🤔
Độ sáng thì phải nói là sáng hơn nhiều nhưng độ bền thì lại giảm xuống cũng k ít. Nếu làm như vậy thì thắp sáng đc mấy canh h là bị cháy thôi à. Vậy thì sáng hơn để rồi vứt thì sáng hơn làm cái gì chứ😅😅😅
Millennial's, am I right? They think this is a disposable world.
bord ısınınca bant gevşeyerek devreyi keser. board gets hot and tape loosens and it cuts off
How to burn your house down with graphite and tin foil modifications to a cheap light bulb. Yeah, I think I got it now... Thanks.
current limited at the DC convertor chip.......the Brightness of each LED are no change
You are correct kk, that's what I am trying to teach to the commenters, but they are dumb and don't understand. Looks like tiktokers are all over.
I believe it is the voltage that is the constant. No current limiting....
defintly constant current.
recipe for fire in your house?
Just buy a new lamp. You will live longer 👍
LED драйвер ограничивает ток, даже, если останется лишь один светодиод, он не перегорит от якобы перегрузки, как здесь многие пишут. Нагрев драйвера возможно увеличится, и только.
the LEDs are wired in series, so the same amount of current from the regulator meant for all of them will split up between less LEDs, meaning each one will get more
holarmusic cleary has not paying attention enough during science class.
NIce job, thank's for the video.
If you remove 1 led bulb from series after someday another led will burnt
just a bridge..wich will make the rest of LED get more current and wear way faster
nope constant current circuit
Regardless, these things are theown away i. Masses because they are not easily servicable.
Responsible production needs to be enforced. Too much wastage is going on for corporate greed
Forgot to put on tin foil hat
It was a great fix until my house burned down.
Good job broo
i hear you loud and clear
Sip
Why not solder new led in 🤔
He showed how to 'resurrect' a dead LED bulb without special skill such soldering etc. Perhaps the bulb's life will last shorter than before, but it doesn't matter.
@@123syamsul It may cause fire shorting circuit.
best but very fiddley with these smd leds.
Wouldn't it be cheaper to buy a new bulb?
Do try this at home
Will there be any change in power consumption?
Yes, it will shortly change to zero. Because doing this will increase the current across the rest of the LEDs and I can promise you they will be short lived. I give it a week at even light use
This might cause fire.
You know what; to hell with all that. I've got a few bucks, I'll just go buy a couple of new ones.
OK...?
....I'll pass, i don't feel like setting my house on fire today.
considering the price of these bulbs it’s not worth the fire risk.
Fantastic idea!!!!!!
No it's not. It's temporary at best. It will increase current across the rest of the LEDs and they will be short lived.
Fantastically bad idea
You just put it on OFF.
100 %
Result !!
I do not understand why you do not use soldering iron. i repaired my bulbs always but i see this video. what for you trying with pencil and aluminium? go solder it.
Its costly.
@@Life_is_short_Enjoy ahah do not live if you do ot have 0.0001 cent
Thanks my house is on fire. But at least it's pretty bright here now.
The thumbnail lied to me.
Неужели вы не можете купить новую? Всё они одноразовые и тратить время неразумно.
top top top
Funny
Do the smart thing and go buy a new $2 bulb ... how cheap are you? Something like this is what intelligent people call "a fire hazard waiting to happen" ...
& se lämp flies dävn ön blödvväyh ^ ^
i can feel how it murders eyes
more current for the remaining bulbs-If overload led life is reduced.........
Yes, you are right. But for the moment it doesn't matter especially in emergency (late night and we don't have spare bulb, for example).
Залепушник! Синяя изолента даже легендарная, отвалится через пару часов. Перемыкать сгоревшие светодиоды совет для глупых пацанов!
All he is doing is just increasing the current amount. He will be paying more money now!🤔😜
Tried this on a phillips led bulb and it doesnt work, can t find the faulty LED.
Good. It's a stupid idea anyway.
It's temporary at best. It will increase current across the rest of the LEDs and they will be short lived
Might be the wires from the socket part of the bulb to the board.
Thanks sharing
Все эти лампы перевод денег; лампа накаливания горит по несколько лет не сгорая,а это говно порой и на месяц не хватает.
Terbiyeli yorum yap mide bulandırma ayıp.
Это не лампы, а продавец. Или электричество.
Да, но только электричества лампа накаливания расходует в 10 раз больше светодиодной при той же яркости свечения.
@@user-dd3sr5dc5g То что берет лампа накаливания ,ты в разы больше истратишь на эти светодиодные покупая их часто или расходуя электричество на перепайку этих диодов,а еще они вредны для нашего зрения.
@@user-pb3cb3eh3l , у меня в месяц за электричество получается цена этой лампочки. То есть за год - 10 лампочек. Работают они 5-7 лет, а если со стабилизатором, то и 20 лет могут. Нет, если заявленные 30000 часов они проработает - гораздо выгоднее по деньгам, чем лампы накаливания, хоть они сами и стоят в 5-7 раз дешевле. Это когда электричество стоило 4 копейки - тогда да.
Just buy some solder
Most graphite in pencils will not do what is claimed, though it could act as a resistor if there is enough carbon content. Note that doing it live is EXTREMELY dangerous as some LED lights have mains voltage across the LEDs. I would definitely NOT Follow any advice is this video. It's too dangerous. LED globes are cheap enough to just replace if they fail, or if you know what you are doing, properly solder a resistor in place to bridge a failed one. If you do what is claimed in this video and manage to get it work, well just remember the carbon poweder from a pencil just falls off and because no connections are soldered, they will fail very quickly, if they work at all to start with. Fire risk is very high
Just buy a bulb with higher wattage. Who has the time for all of this?
Brightness Will Increase - life will decrease
Wat is name of tat which ur checking the led
If you don't want your house burn down, don't do any of those craps. put a new bulb in.
У меня уже несколько ламп горят после такого ремонта больше года. Светят ярче. Использую в быту в нормальных условиях.
Это просто муж забыл вас предупредить, что он давно выбросил лампы "после ремонта" купил и вкрутил новые.Вот они и нормально горят.Сегодня даже новые лампы ,и те не все работают по году и дольше, а вы тут рассказываете сказочки, как у вас выхолощенные так долго светят.Я несколько раз пробовал такие "ремонты" , только посерьезнее, с хорошей пропайкой,но лампы после этого живут считанные дни.
Не пезди пиздобол. Больше года.
You bumped your head
is that real?
Perform at your own risk. Don't believe everything you see/read on the internet.
@@philparrish6914 true
Yes, but it's a waste of time. It's temporary at best. It will increase current across the rest of the LEDs and they will be short lived
Thanks you for the good idea.
It's not really a good idea