Modification of Parkside PMSG 200 A1 MIG/MAG/MMA welder | Part 1 - Cables and Choke
Вставка
- Опубліковано 5 жов 2021
- In this part you will see: Replacement of all internal power cables with 25 mm2 copper conductors and addition of an extra choke for higher inductance. I also made a new 25 mm2 Cu ground cable with a 200A clamp.
After modification the welder welds more smoothly. Because of the extra choke, it fires better when spotting lower currents and sizzles less.
The aluminium cables inside the welder are approximately 1 m long and have five connections with poor quality thin flat crimp connectors. There is a voltage drop across them.
I make all modifications so that they can be returned to their original state.
To replace the internal cables: About 1 - 1,2 m of 25 mm2 welding cable, 2 pieces of crimp cable eye ring terminal 25/6mm and 3 pieces of crimp cable eye ring terminal 25/8mm. If you also want to add a choke, then you can use a 13uH, 180 A choke like FERYSTER DEHF-42/0.012/180.
To make the ground wire: 3m (or as required) of 25 mm2 welding wire, a welding clamp with a good quality copper jaw (200A or 350A), and a 10/25 cable welding terminal.
3D model choke inductance holder is downloadable:
cults3d.com/en/3d-model/tool/... - Наука та технологія
Adding an inductor is a very smart action!
Great job! nice video filming!
Nice video mate !
Thanks for the nice work ! Greets from the Netherlands.😃👍
Thank you. Greetings from Slovakia.
Krásna práca. Konečne ďalší SVK kanál. Držím palce na rýchlych 1000 SUB.
Ahoj a vďaka. S tým rýchlym počtom odberateľov to ale nebude u mňa až také ľahké a rýchle. Nie som LidlTuber :-) Chcem prinášať vlastné riešenia a nápady z rôznych oblastí, čo vyžaduje vec vymyslieť, navrhnúť, vyrobiť a zrealizovať. Znamená to menší okruh ľudí, ktorých zaujíma nie len riešenie ale aj nápad a prevedenie na istej úrovni.
Po tomto videu začínam odber
Nemá tá zváračka od výroby tlmivku ? Načo pridávať dalšiu ? Inak super video dávam odber 😉
Yes the induction is very inportant for clean weld. I bought chinese copy of Everlast with button for induction adjusment, was skeptic about it if work, but yes its working, dont know why parkside didnt make in that way. The welder cost me 200 euros.
thank you very much for your work
Thanks
Thanks for this well made informative video!
Would you mind specifying which parts you used for this?
This will help me (and others) doing buying the required parts for this useful modification.
Vopred ďakujem!
Hello and thank you. You'll need one of these if you'd like to do it exactly like I did:
To replace the internal cables: About 1 - 1,2 m of 25 mm2 welding cable, 2 pieces of crimp cable eye ring terminal 25/6mm and 3 pieces of crimp cable eye ring terminal 25/8mm. If you also want to add a choke, then you can use a 13uH, 180 A choke like FERYSTER DEHF-42/0.012/180.
To make the ground wire: 3m (or as required) of 25 mm2 welding wire, a welding clamp with a good quality copper jaw (200A or 350A), and a 10/25 cable welding terminal.
Out standing cheers :)
Parkside should watch this video !!! I am returning mine as I mainly would do gasless flux core which splatters so much on this machine. Lovely informative video bro. Kudos new subscriber from Malta.
Hi, thank you and best regards!
When running gasless welding wire - connect the Earth to positive and Torch to negative, otherwise known as "DC electrode negative", or "straight polarity". (This is the opposite to standard MIG welding with gas, which is torch/wire positive and earth negative).
@@weldphd Thanks for your reply. Yes I did the electrode negative thing yet there still is too much splatter compared to welding sets costing a mere 50 to 100 more. The gas option is very good yet I find that 40 W minimum is too high for anything less than 2mm
When doing this modification, and using only flux core wire, Should i connect the choke to the line for using flux core wire?
Great video, thanks a lot! Do you know if those modifications also fit 1 2 1 to the newer PMSG 200 A2 welder?
thanks
Uwe
I don't know the construction of the PMSG 200 A2, I don't have it.
Sehr gute Idee und sehr gute Umsetzung. Ich mag das PMSG sehr.
Mit der zusätzlichen Spule soll ja der harte „Einsatz“ beim Schweißen reduziert werden.
Gibt es schon Erfahrung ob sich dadurch die „Spritzer“ reduziert haben?
Das einzige was mich bei dem Gerät noch stört ist, das sich der Strom nicht unter 50A regeln lässt.
Manchmal stößt man damit bei Dünnblech an die Grenzen des machbaren.
Ist es möglich auch hier Hand anzulegen und die Einstellung auf zB. 40A zu reduzieren?
These modifications cost me about 45 Euros. The welder cost me 158 Euros, which is 203 Euros in total. For 200 there is nothing else that welds better. All welders that weld naturally better cost twice that price. In doing so, even some welders for 380 - 480 Euros have aluminum wires and aluminum grounding cables and less good pliers in them. In any case, the investment has paid off.
Dujú hovoriť in Slouaensky? 🤔
@@majkokorko Ja hovoriť slovensky.
It's a good video I like it. Could you tell me please can I put this on the minus pole to?
Yes. Thank you
Thanks for your answer.
I can see you're printing bumper corners as a kit, will this be available as a kit too for people who doesn't have crimping tool with a bit longer cable for euroconnector then original? At least without choke, cable can be cut and soldered easily but crimping is not available for everyone...
Nice video!!
Wat does a choke do, and what is its function on this welding machine??
Thank you. The choke smoothes the voltage waveform, especially at low currents and improves spotting.
@@Tech-3D Thanks!👍
can you explain what the choke does? You say higher inductance but what effect does that have?
Information given in the description below the video.
Thanks for your comment on my Factory parkside tig torch video, I came over to check your channel and really like it, subscribed! I know a real Parkside connoisseur when I see one, using the parkside cable stripping tool :) What kind of improvements did you notice after the upgrade? How long did it take to animate your intro, what program did you use, I'd like to make something similar for my channel? Keep up the good work, cheers!
The Parkside stripping tool is a good tool, although not as good as my old JOKARI No15 stripping tool. It has a suitable blade height and cuts through the insulation on 25 mm2 cable without damaging the conductors.
After modification the welder welds more smoothly. Because of the extra choke, it fires better when spotting lower currents and sizzles less.
The aluminium cables inside the welder are approximately 1 m long. All have poor quality thin flat crimp connectors. There is a voltage drop across them.
I made the animated intro in about two hours using plugins. I use Final Cut Pro X on Mac OSX.
ok grazie
Jakou jsi zvolil tlumivku? Jaké má parametry? Děkuji za odpověď.
FERYSTER DEHF-42/0.012/180 13uH, 180A
The welder will be an inverter type? I am almost sure that a choke should only be fitter to a transformer (old buzz box) type welder. calculations are made so that the choke matches up with transformer. . I hope that choke does not damage yours as it works at a very high frequency. Someone correct me if I am wrong.
Chokes are commonly used on inverter welding machines. Some more expensive MIG/MAG welders have electronically adjustable chokes. Don't worry, the welder will certainly not get damaged because of the choke, as the one output choke is already there from the factory :-)
@@Tech-3D As my mate said "you learn something new every day" many thanks
@@daracus1202 We are all learning. Thank you and may you do well.
Good video !!. Can you advise us another cheaper choke with the same or similar especs. 30 eur is in my opinion too much for just one component.
Thanks in advance. Greetings from Spain.
Thank you, but I can't help with a cheaper one. A choke for such a high current will always have a price, and the chokes that are available as spare parts for welders are either even more expensive or dimensionally larger.
Does this modification helps for gasless mig welding?
On any type of welder, a good choke will help with arc ignition and burn stability.
Hello agaín. I have done the changes you show in your video. Even so, I would like to do another question. I was wondering what about the wires of the external welding gun and the electrode clamp. Should I change these wires too ?. If I change the ground wire, why don´t change these two components wires as well ? . Thanks in advance.
Feel free to replace the welding gun as well.
Hello, thanks for the video, i am just waiting on parts to make this modification. Should we solder the wires directly to choke ? or is it possible to use some connector to choke that is crimped on wires ?
What about the welding torch ? is it ok or should be replaced for something better ?
What about the ferule to use in the 10-25 quick connector? any specs or we can use anything.
Hey. It is best to solder the choke, it is designed for that and has tin coated winding ends. The connectors are unusable, due to the high currents that flow in the circuit. It is still possible to fix the cable to the choke by drilling holes in the winding cubes for an M3 - M4 screw and tightening it with a screw joint.
The welding torch is ok, just replace some better quality tip there.
The 10-25 quick couplers are standard, copper, nothing special.
@@Tech-3D ok i will solder it... any reccomendations for the tips ?
what are the parameters....thread length etc ... is it M6 x 25mm ? could i use any other length ?
@@Dulus0 If you mean the eye ring terminal, see the description for the video.
@@Tech-3D i meant tips for welding torch ... the welding torch is i think copy of MB15 AK and that uses welding tips M6x25, correct ?
@@Dulus0 Yes, M6 and length 25 mm. I recommended tips CuCrZr, not as frequent replacement as with E-CU couplings.
thanks for your contribution
a doubt, if the choke is 180A
What happens if you weld with tig at 200A?
Nothing happens :-) This welder will not realistically give 200A continuous current in the WIG method.
thanks for your prompt response@@Tech-3D
It will heat a bit more, then the smell of burning laquer will indicate overheating)
@@nt976 ok, thanks for your contribution
Is there any way to disable post-gas ?
Only by some modification to the throttle valve switching. For example, turn it off when the engine stops or the trigger button is released.
How much is improved by changing aluminum cables to copper cables?
This is individual. It also depends a lot on what is being welded, or at what high current, or what gas is used. In any case, arc burning is more stable. However, if the welder is used occasionally and for undemanding hobby welding, the welder may not even notice it very much.
@@Tech-3D thanks a lot
Ciao puo dirmi dove ha preso i supporti per fissarlo?
Ciao, che tipo di supporto intendi?
how have you calculated the size of choke to the size of welding machine. Is this related to maximum amps on welding unit. Please help a novice.. :D
The choke is not calculated or designed specifically for this welder. I used a proven choke that is also used in welders and is for current up to 180 A.
Tech 3D ok
ciao il supporto per fissare l induttore interno alla saldatrice
Ciao. Ho progettato e stampato il supporto dell'induttore su una stampante 3D. Se siete interessati, potete scaricare il supporto da Cults3d, il link è nella descrizione del video.
Hello! Suitable for a2 modelo?
Hi, I don't have the newer A2 model. I don't know.
Ahoj. Super video, inšpiroval si ma ;-) Len drobná otázka, tlmivka sa montuje na + výstupu alebo je to v princípe jedno? Lebo mám jednu, len je väčšia a asi by tam nesadla, preto by som ju mohol dať len externe cez - pól. Vďaka.
Ahoj, ďakujem. Tlmivka sa zapája kdekoľvek do obvodu, takže kľudne môže byť aj externá.
@@Tech-3D Vďaka za odpoveď. Čo sa týka tlmivky, je na to nejaký výpočet alebo pravidlo alebo tam môžem dať (s rozumom) akú chcem? Lebo doma mám túto: omicron(bodka)sk/products/vystupna-tlmivka-gama/
Tak či pôjde použiť alebo nie?
A chcem sa ešte opýtať, na kanále ForWorkAndFun si písal, že na tejto zváračke ide zvýšiť zaťažovateľ. Ako sa to dá spraviť? Vďaka.
Great video. I´m gonna do the same modification. One question about the wires. When you say internal cables and ground cable, are you using exactlyl the same kind of wire ?. I understand that all the wires, either ground wire or internal wires, are Cu welding wires. Please correct me if I´m wrong.
Thank you, yes the same cable everywhere.
PMSG 200 A2 - also has aluminum wire? It's 199Eur so ?
I don't know. I can only assume that at this price level, aluminium is used everywhere in these Chinese welders.
@@Tech-3D Does it state anywhere what cables are used? Did you contact Lidl to ask them? In Germany there should no problem to get this information, maybe it turns out Lidl is selling fakes? Who would want welder with 12mm2 welding cables ? 25mm aluminum is same as 12mm copper.
Great video, I will absolutely try the same choke and cables!
I would like to ask you if you have tried to weld 1,5mm iron with this machine and what kind of settings/wires did you use, because with the 1mm no gas wire included, I had a lot of troubles with the lowest amp settings (50 amp).
Thank you
Set it on 1.0A (Upper) and lower down voltage -5 or what ever you like best.
Super video, tiež mám túto zváračku a zvára super, hoc mám už Omicron 1550, ktorá si asi bude hľadať nového majiteľa, kedže táto Parkside ju oveľa lepšie nahradí. Akurát mám v košíku tlmivku z TME :-), ale chcem sa spýtať, ako zásadne sa zmenilo zváranie po tejto modifikácii? Je to cítiť ak hej v čom? Jedná sa mi hlavne o zváranie MIG/MAG a TIG. Ďakujem veľmi pekne za odpoveď. Kábel si kupoval kde?
Vďaka. S TIG zatiaľ nemám skúsenosti, preto neviem posúdiť. Parksajdka zvára aj bez úprav v podstate veľmi slušne a za tie peniaze nemá konkurenciu. Všetko čo zvára lepšie je dva krát (a viac) drahšie. Je to cítiť pri malých prúdoch a bodovaní, drôt sa lepšie zapaľuje, to dohladzuje ešte tlmivka, a pri väčších prúdoch, neochádza k takému úbytku napätia na kábloch a prehrievaniu. Čo sa týka úprav, tak asi najzásadnejšie je vymeniť ten zemniaci hliníkový vodič s plechovou svorkou za kvalitnú meď. Kýbel som kupoval na zvaracka eu.
Zdravím, jaké paramtery tlumivky zvolit?
Hello I have a problem with the machine,I bought it as open package and when I started it, it goes on but it does not react to pressing any button,it does not react to roller for voltage setup, the screen for voltage blinks showing 0,H then 74,3 constantly.
The screen for amperage shows 890.
Neither value can not be changed.
Any idea what coule be cause ?
Probably the control unit is defective.
@@Tech-3D where could I get a spare one? or can this one be repaired? well I guess this is how you end when you buy of of Ebay, I bought it as a new - but open box , paid and waited 15 days to arrive and when I start it it starts, the fan works, but buttons do not react, upper displays shows 74.3 than O.H, and the buttons have no reaction at all...
@@Tech-3DThanks for fast answer. Can it be fixed or replaced and where can I find new contro unit ?
Vďaka za super video, mám rovnakú zváračku a zvažujem túto úpravu. Pri zváraní s elektródou očakávam zlepšenie. Ovplyvnilo ti pridanie tlmivky nejako zváranie na MIG/MAG, alebo v TIG režime?
TIG nepoužívam, taktiež elektródu. Pri MIG-MAG je lepšie zapaľovanie oblúka, hladší zvar s ArgónMix, neprská tak.
Hi, electricity travels on the outer wall of a conductor, so alu core but copper shell is an economical solution, and should be ok.
Hi, try to measure it 😃
@@Tech-3D exactly my thought...
read a bit more on this, then spread it on the internet :)
Electrons travels on the outer wall of a conductor only at high frequencies, not on DC. Would be MAYBE ok on AC tig for alu welding, not on DC.
Zdravim. Kde kupujete tie ocka a konektory?
Hagard Hal, TME, zvaracka.eu
@@Tech-3D dakujem za info.
The airflow is a calculated matter. It is not adviced to change it by lowering the flow. Electronica getting really hot and need to cool otherwise they will burn up. The best way to lower the noise is to buy a silent one.
This is all true, but it relates to heavy use of the welder. I use the welder mostly without a fan and have not managed to overheat it yet. When it overheats, the indicator light comes on and shuts off. It has its own thermal protection. When I'm not using it at full power but only at 40 - 60 amps, or when spotting, or clamping the structure before welding, or when I'm doing short welds with breaks, I don't need the fan to run constantly and suck dust. I can just turn it off, and not even feel the welder heat up. When I'm welding at 130 amps and long welds, I'll add the fan speed.
@@Tech-3D sorry, not a very good argument. Overheated electronisch will break much earlier than cooled ones. Does the fan irritatie you? Replace it by a silent one with the same capacity. Overheated electronics can be dangerous. Maybe you use it in a safe way, your viewers might not. Your project is a nice solution as a fanregulator, but a warning is adviced. Keep up the good work!
@@HanD_1964 In the case of the Parkside welder, I disagree. The point is that the load capacity quoted by the manufacturer is understated, in practice there is no overheating when used according to the load table. Another factor is that the thermal protection value is on the low side and does not even reach the semiconductor operating temperature limits.
Another factor is that if you were to closely examine the parameters of the fan used, you would find that there is no fan available that has the same static air pressure and the same air flow with less noise. There are only a few Panasonic fan models with the same parameters as the mounted noisy fan but their price is worth a third of the price of the welder.
If the welder were to break down sooner, that is not a problem because it would have to break down before the 3 year warranty period. In practice, however, Parkside welders break down to a manufacturing defect in the semiconductors or Mosfets, or to a short circuit rather than overheating. However, this is exactly the opposite of the case with Parkside power tools, which suffer from overheating of the windings of the stator motors and rotors in angle grinders.
@@Tech-3D Ok, we disagree. The best way is to inform Parkside and advice them to use low noise fans like other brands do.
What about the responsability to your viewers?
Maybe an idea to build an automatic speed regulator as a fine compromis.
@@HanD_1964 Automatic fan speed control is not a compromise. Automatic temperature control means disconnecting all connectors from the motherboard, removing the motherboard, drilling a hole in the heatsink, installing the thermistor - temperature sensor and controller.
Basically, I have no problem to rebuild even this PWM controller for temperature based control in a few minutes. But all this means LOSS OF WARRANTY.
All modifications to the welder, in case of failure quickly, I did as easily reversible and quickly putting it in its original state, without interference to the electronics. It's just an idea, it's not a guide or a recommendation. Whoever wants to, do it their own way, maybe with temperature control or replace the fan or leave it that way.
prosim vas načo ste tam davali tlmivku, ked tlmivka uz je na doske?
Uvedené v popise k videu.
Parádně kvalitní videa, musím hlavně pochválit kvalitu osvětlení a obrazu. Střih bych trochu zkrátil, např nepotřebuji vidět kazdé krimpování očka. Šlo by ještě udělat video jak svářečku používat v režimu MIG? Vím jen, že budu potřebovat CO2 bombu, ale zbytek je pro mě tabu.
Ďakujem. Osvetlenie je vlastnej výroby, z môjho prvého videa ua-cam.com/video/PXN5Z1EWXVk/v-deo.html, a som s ním veľmi spokojný.
Ďakujem Ti aj za pripomienku k strihu, máš pravdu, beriem, nabudúce to zlepším.
Čo sa týka zvárania MIG/MAG, zatiaľ nemám v pláne k tomu robiť video, pretože takých videí sú stovky. V podstate na zváranie s inertným plynom alebo aktívnym plynom potrebuješ vhodný drôt a vhodný plyn. Plyn volíš podľa zváraného materiálu, buď CO2, mix Argónu a CO2 alebo čistý Argón. Okrem tlakovej fľaše potrebuješ ešte redukčný ventil a plynovú hadičku do zváračky.
A ďalej čo sa týka zvárania tak postupuješ štandardne. Nastavíš na zváračke nejaký vhodný prúd podľa hrúbky materiálu, ako štartovaciu hodnotu, zváračka podľa synergie nastaví nejakú hodnotu napätia, na redukčnom ventile nastavíš prietok plynu na hodnotu 8 - 10 l/s a začneš zvárať. Podľa správania sa zvaru a aj podľa zvuku zvárania upravíš prúd (zváračka tým de facto zmení rýchlosť podávania drôtu) a potom to ešte jemne doladíš zmenou napätia. Nejde to naučiť sa to za hodinu ale treba to skúšať, meniť a hlavne získať zručnosť v rukách. Ale ako som psal, na internete sú skvelé videá o tom.
@@Tech-3D Děkuji za vyčerpávající odpověď. Zatím ještě tuto svářečku nemám, ale připadá mi, že proti elektrod by mi Mig ušetřil hodně času. Po odladění tedy 🙂 přeji hodně štěstí s kanálem, věřím, že když vytrváš tak se úspěch dostaví.
Reguláciu otáčok som tiež urobil, ten hluk bol otravný.
Tvoje video je pre elektro - zdatného zrozumiteľné, ale hlasový doprovod mi tam chýba. Je to také neosobné, suché..., laik nemá šancu si to podľa neho urobiť.
Máš pravdu ale video nie je návodom. Ani mi o to nešlo. Zverejňujem len svoje nápady a riešenia prevedení. Ten, kto chce, môže sa inšpirovať ale spôsob prevedenia si zvolí podľa seba. Môže použiť iný regulátor, nemusí použiť PWM reguláciu ale napäťovú reguláciu, môže si to umiestniť na úplne iné miesto alebo si vymení ventilátor za ventilátor s nižším prietokom alebo ventilátor tichší.
Ak niekto nemá 3D tlačiareň alebo si nevie navrhnúť montáž na regulátor v 3D programe, použije nejakú hotovú prístrojovú škatuľku.
Dá sa to urobiť všetko aj inak a určite aj lepšie, ak by sa zváračka rozobrala viac. Nevadí mi viac rozobrať zváračku ale všetky úpravy som robil s cieľom minimálneho zásahu do zariadenia tak, aby všetky úpravy boli vratné a v prípade poruchy zváračka neprišla o trojročnú záruku kvôli zásahom do nej. Niekomu na tom nezáleží a kľudne ju celú rozpitvá, poprestrihuje káble, stočí ich a olepí páskou. Takže ide len o inšpiráciu a ukážku práce.
Jak se to chová proti verzi bez tlumivky? Ovlivňuje to mig svařování nebo víc mma?
Aj MIG aj MMA... Všetko podstatné je už myslím napísané v komentároch pod videom a popise k videu.
@@Tech-3D díky, za odpověď, mám ji taky a občas se přilepí kostra ke svařenci, ty kabely vyměním.Pod tu tlumivku ten držák nikde nevidím asi výroba 3D?
V popise pod videom
ked zoženiem aj ja taku tlmivku tak sa pokusim dat aj ja do svojej.... dakujem za inšpiraciu.... na spojenie tlmivky ake kable mozem použit? vela miesta vo vnútri nemam ... ma zvaracku Laston mini 160 HT .... dakujem p.s. ked som si dobre vsimol tak tlmivku si dal na +sko ? niekde som videl video a tam zase na -sko.... kde by som ju mal dať?
Kdekoľvek do obvodu...
tu tlmivku si kde kupil v TME ?
@@radofer Ano
Kde seženu ten plast pod tlumivku? Díky
Pozri popis k videu, pod videom.
Našel jsi pod videem tu podložku pod tlumivku? Hledám....
Dove posso scaricare il file per stampare gli supporti della bobina?
E anche protezione angoli
Il link è nella descrizione sotto il video.
Dobrý den mám jen drobnou otázku. V popisu potřebných součástek máte napsané lisovací oka 2x 25/6mm a 3x25/8mm podle videa není poznat kam jste které použil. Mě přijde že u desky jsou všechny oka stejná ale to by musely v tom popisu být některé 4x a to není. Děkuji za odpověď omlouvám se za hloupou otázku.
Dobrý deň, 6 mm idú na dosku, 8 mm na rýchlospojky a pohyblivý prívod ktorým sa mení polarita k horáku.
@@Tech-3D Děkuji.
Can you do the same in the PPSK 40 A1?
I don't know the construction of the PPSK 40 A1, I don't have it.
@@Tech-3D how can I contact you? E-mail?
@@SrTiKuka Yes
@@Tech-3D what is your e-mail?
It is presented in the information tab of the Tech 3D channel on UA-cam.
These modifications are great for you! I'm interested in this choke you added ... did you make it yourself or not? I have the same device and I would like to improve it ... so if you have any more advice .. Sorry in bad English :)
Greetings from Croatia!
Thank you. I have given the choke parameters in the description to the video.
@@Tech-3D thanks! Go on💪
Jak a kde se da sehnat za 160 eur?
V Lidl e-shope, keď je akcia, alebo veľká zľava na všetko cez víkend.
👍👍👍🤝🤝🤝
Uměl by někdo udelat ve 3D ten držák tlumivky?
Možno stačí čítať popis pod videom :-)
Sei italiano? I cavi sono made in Italy
No, ma i cavi Made in Italy sono venduti in tutto il mondo. Immagino che siano buoni :-)
@@Tech-3D ahahah ho visto che sei della Slovacchia. Grande! Sei dello stesso paese di for work and fun che è un altro grande.
Comunque sei bravissimo. E fai dei video splendidi. Continua così! Ti seguiamo dall'Italia 💪
??
А сразу нормальный аппарат купить не судьба?
Конечно, нет. Обычный сварочный аппарат, который сваривает так же хорошо, стоит как минимум вдвое дороже. К тому же, я бы не получал от него такого удовольствия, потому что не смог бы настроить его под себя, что мне нравится.
Я купил сварочный аппарат на распродаже за 158 евро, модификации и кабели обошлись мне в 45 евро. За цену обычного сварочного аппарата, которая составляет около 400 евро, я получил баллон с аргоновой смесью, редукционный клапан, шланг и сварочный колпак True Color. Кроме того, даже некоторые сварочные аппараты ценой 450 евро имеют алюминиевые кабели и некачественные сварочные клещи.
Это идеальный сварочный аппарат за небольшие деньги с гарантией 3 года.
Ahoj. Keď si spajkoval kable k tlmivke prikladal si ich len z jednej strany alebo si ich rozpolil a spajkoval z oboch. Nie je to na videu dobre vidieť.
Lanenie káblov je rozpolené a pevný privod od tlmivky je vložený doprostred. Zaspájkované je to potom spolu. Stačí z jednej strany, kvalitný cín s dobrým tavidlom sa rozleje. Takto kábel vychádza z tlmivky v ose vývodov.
Autor videa je zručný a bezpochyby technicky vysoko zdatný.
Mňa by veľmi zaujímal výsledok takejto úpravy v praxi. Som tiež elektromontér, elektronik, rádioamatér... a teoreticky rozumiem, čo spôsobí zapojenie tlmivky do obvodu, ale rád by som poznal Tvoj názor na praktické zváranie po takejto úprave.
K mojej otázke ma vedie najmä skutočnosť, že oddnes som majiteľom práve tohto typu zváračky. 🤔