Because I use this video OFTEN as a reference for this board, here are some bookmarks: 0:57 - What is the BigTreeTech SKR Mini E3? 2:21 - What is Different From V1.2 to V2.0? 4:09 - How do you install the mainboard? 4:57 - Compatible out of the box? 6:11 - How can you compile your oen firmware? 8:39 - How does the new EEPROM work? 9:01 - BLTouch Compatible? 10:42 - Filament Runout Compatible? 11:45 - Neopixel and other accessories? 12:59 - TFT35 Dual Mode Touch Screen 13:37 - 3d Printer Wifi 13:43 - UPS 13:55 - How to activate sensorless homing? 15:07 - End summary
thank you kyle! i just finished the long install of all 3 e3pro upgrades and bounced between 3 vids because theres a dif nugget of info in each vid...nothing worked right and i flashed and no ttft display after flash...wracked my brain...drank went to bed...double checked every wire config...bltouch connection wires red and blue were flipped...fixed...found out the damn reset button on the display was being pressed by the factory mount...WHY?! now i sit here dumbfounded and yep...
Kyle, I found this on the listing on Amazon.US for this board 2)Because the fan on the SKR Mini E3 V2.0 control board is a CNC fan, you need to set the wind speed before using it. (Note: V2.0 version of the fan is not ready to use after power on) This looks like BS to me as I can't find any documentation online to support this claim, I did however find issues of people receiving boards with faulty MOSFET's and think this could be some type of getting out for the retailer trying to make people think they have done something wrong with their board, My board worked fine out of the box
Another great guide. I swear, you’re carrying the ender 3 community. I’d have never bought one if not for detailed guides like this. It’s a good thing you’re a science teacher, because you’re great at it!
You'd never have bought the Ender 3 if it weren't for these guides? Don't get me wrong, Michael has the best guides on UA-cam, but the Ender3 has been the best value FDM printer for the last 2 years running.
@@Drakoman07 same here and I agree with what you said (in an odd backwards type of way). I bought the ender 3 based on lots of research with his being very helpful. In hindsight, I would also say "id never have bought one either if it wasnt for micheal. aka: i wouldve had a teribble time trying to figure it all out and probably given up bc well all know DesignProtoypeTest isnt about to put in half the work towards being as helpful, detailed and budget friendly. Not everyone can just up and spend $300 on duet and 5' screen since i spent 2/3rds of that on the printer itself
My son chose to buy the Ender 3 Pro in August based on channels like this and the comments from owners. We've had a straight forward climb from build to very high quality prints in multiple filament types and never looked back. I'm extremely grateful to this channel and the comments from users about their experiences and ideas. There is no way the journey would be as easy as it has been without all of you. Yes it's a bunch of work, careful watching and reading etc, but still no big issues of any sort, and the print quality,,, wow. We upgraded during the build process ( extruder, bed springs,and wheels etc ) , I can't say enough about the value of the learning process , maintenance details and understanding the role of each component that this channel has provided. We use Solidworks to design, those drawings are done very differently had we not had the overall printing experience the Ender ( any good printer ) has provided. It forced us to do small upgrades incrementally and really understand printer setup and tuning adjustment. Best Wishes to all who contribute and Thank You !!
I recently bought an Ender 3 (my first 3D Pinter) and was looking for ways to upgrade it. I started watching your videos while researching printers. Once I got it and started printing, I knew I wanted to quiet it down. So I got the SKR Mini E3 v2.0 and TFT35 E3 V3.0 and installed them. Holy shiznit! It’s so much quieter. The touch screen feels like it belongs in this century. Now I’m looking forward to add a BLtouch and filament run out sensor. I just wanted to let you know that your videos have been helpful and informative as I venture into this new hobby. So, thank you and keep making great videos. :)
I also just bought the Ender 3 as my first printer, will be building it this weekend. I also am strongly considering at a new motherboard adn agree this channel has many helpful videos. :-)
So after installing the SKR Mini E3 v2.0 I was still having trouble with first layer stick and bed leveling in general. I'd already ordered a BLTouch v3.1 and it arrived a couple days ago. So I got it installed along with the firmware available from BTT on github. It took me a little bit to get things figured out but now prints are sticking and I'm getting consistently better results. Yay! :)
@SereneScream considering it too. I have bed adhesion issues as well, have to use the z babystep on the first layer to Get good adhesion then turn it back. Its a pain in the ass
The biggest problem with this upgrade: After you install it, everything else on your printer seems LOUD. Especially the board cooling fan. Which means you'll need to swap those things out, too :D
github.com/StevenCreations/Marlin2.0.x_SKRE3 here is my bin file the hast fast bed leveling and no bugs unlike the big tree tech bin files on github. no issues at all. check your wiring if they are still loud
As a person that has owned an Ender 3 for less than 24hr, I was able to drop this into my stock unit without any issues. Massive improvement to noise and really happy to see you've tested out a lot of the popular upgrades! Side note: Awesome channel. Been very helpful with me dipping my toes into 3D Printing!
My son and I are in the process of purchasing our first 3D printer and have narrowed it down to 3/3 Pro/5. How user friendly is the 3 for first timers?
@@bocconom i just got an ender 3 pro a few weeks ago (for the price its so worth it) , easy to assemble (you shouldn't get stuck but if you do youtube has alot of build guides for all models!), the hardest thing is probably getting the bed level, its not hard to do, but make sure you put in the time to make sure it is as close as you can get it, again youtube guides help you, but once you've done that, its literally load filament choose your model and print it! :D always watch your first few layers to make sure it sticks to the bed! if you ever get stuck theres so many videos on here for 3d printers to help you! good luck
I have a stock Ender 3 Pro. I didn't know it could be upgraded with sensor-less homing, wi-fi or a touchscreen! This video is awesome. I will definitely be looking for the upgrade parts per your recommendations. I'm just as excited to modify the printer as using it to make 3D prints. I really enjoy my Ender 3 Pro and I'm a complete newbie to this hobby (that's what it is for me at the moment). But, I really like designing my own parts to fix things around my home and simply trying out new ideas. I have a sincere trust in your information because you demonstrate how thorough you are and that's incredibly important to me. After I watch your videos, I don't have to guess at what choice to make. I simply have to decide where to buy from. Thanks for your continued efforts on the Ender 3 Pro and please continue to educate those of us looking to learn more about the printer itself and printing techniques, tips, etc. Thank you.
I bought the mini E3 largely because of your video, and I was blown away by how much better the printer performed with it compared to the stock board, particularly regarding noise. I've recommended it to a couple friends as the first upgrade they should buy for their printer, and they've been happy with it as well. Through my journey in printing I've watched your videos, so thank you for helping educate me and many others in the community. I started looking deeper into duet boards a week or two before your video on them, and they seem quite promising and offer several things that marlin doesn't have yet; it would be interesting to see how using a duet in an ender 3 impacted performance and usability. Happy Printing!
Got one delivered one day before this vid went up. On an Ender 3 it's just plug and play, and since I already have an SKR 1.3 running my AM8, I think I could have figured out how to get sensorless homing and the Bltouch to work, but now I don't need to anymore. :]
Great video Michael, I just got the BTT SKR Mini v1.2 and I am extremely happy with it, This new upgrade looks like a great upgrade. Thanks for sharing this video.
I've just upgraded my Ender 3 pro to the SKR min V2.0. Only 2 small issues when using octoprint. I didn't get any comms via the USB port, I'm using a pi 4 and the USB operation has changed. Evidently you need to add "over_voltage=1" to /boot/config.txt of the pi, I had no issues with the stock ender board and the pi so it must be different on the SKR card. Secondly, something I was going to get around to on the previous board but didn't was to put a slither of polyamide/kapton tape on the +5v contact on the USB cable so the pi is not powering the main board. I had false overheat protection alarms from the printer if you turn the main power off on the printer with the nozzle still hot. I didn't get that with the previous board so assume overheat protection wasn't enabled although the version of firmware supported it, it was the stock Ender firmware. I believe thre are other issues around powering the board form the pi, here's a good reference github.com/bigtreetech/BIGTREETECH-SKR-mini-E3/issues/41
My suggestion is to buy a lot of filament. And check out this build video and the one from CHEP. Did you notice that the ender 3 pro is now on sale for $209?
Watch a few build videos I think it was 3d print tomb or something like that saved me sooo many potential heart aches... And start watching a vid on bed leveling when ever in the bathroom
i would love to see a video of converting a creality machine with dual z steppers into dual z endstops like what a i3 mega has. unless there is a better alternative. great video as always
I used this video a while back to updage my ender3. I came back just for the dragon clip to test my new prusa, and you desrve the views. Amazing work man. Glad your still at it.
For those who bought the board for Creality printers: Remember that the positions of the mainboard fan plug and the parts cooling fan plug are switched on the SKR E3 v2.0 and the Ender 1.1.4 mainboard. This is also shown in the wiring diagram but I think it's not directly mentioned in the video.
I was exactly looking for this information... I noticed the discrepancy between the cabling on the original Enders board and diagram shown in the video. Thanks!
Done! The noise difference and driving smoothness is astounding. I'm going to order silent fans for the motherboard enclosure and the PSU because now they sound loud as heck in comparison.
I installed one of these as a retrofit on a Wanhao I3 Plus this weekend, and the only thing I haven't gotten to work is using the second fan connector to be a auto hotend fan. Defining it as the auto fan, it powers up on startup. Other than some pid tuning for the bed and hotend, it's working well with a bltouch also. I didn't bother with sensorless homing.
Picked this up a few days after it came out. LOVE the results I’m getting with it, especially the reduction in noise. Wish I had this guide when I installed it, but forced me to learn.
Just installed the v2 in my ender 3 pro and I'm pretty happy aside from two issues. 1: clicking Stop Print does not immediately stop the print. I have no idea why but there is often a delay between 10 and 30 sec before the print stops and while I don't use this much, when I want to stop a print, I want it stopped NOW! 2: It may be the lack of motor sound but now the other fans sound SUPER loud. This second one is less a serious issue but any ideas on #1 would be greatly appreciated. Love the channel.
Thank you for making this video. I have been going a little crazy trying to figure out why my bltouch isn't work when I try and do a z homing when it is plugged into the probe socket. When someone told me I no longer need the Z endstop. Now I can see that I do need the Z endstop. Thank you it has been most helpful.
4:31 in the diagram the label for G and I should be switched around. had this problem that my part cooling was always on, but now when i switched it up the "G" should be in the "I" it worked normally Please take note of this!
Michael, I like your channel content, you are always providing good info. Also, it is nice to see that you are an F1 fan too. Glad that the new season starts this weekend.
4:29 - Just a heads up that at least on an original CR-10, "B" in your diagram is backwards. I don't know if the polarity is reversed on the SKR board or on the bed heater relay. Either way, after getting a bed heating error I swapped the red and black and it now works fine.
@@chrisstock5210 Yes. I had never taken the time to understand all of the Marlin firmware so it was a good exercise. There's a reddit post on building the firmware for Ender which I followed but started with the generic Marlin Example Config for Cr-10 and retained all the CR-10-specific items, mostly bed size/dimension related config.
This is such an amazing upgrade, buing this with a BLtouch has saved me from having to install a bootloader, and it made it incredibly quiet. Definitely worth the money.
@@doctorsnaketown I think because as you get into the Maker world it turns out to be a popular plugin for using VS Code to program stuff like arduinos and other microcontrollers. But if this is your first entry into that world then (like for me) it is definitely hard to know 🤣
Nice, I just put one of these in my cr10 mini a couple of weeks ago. A great board. With bltouch I had to swap red and yellow wires in the plug to the board
Something to keep in mind: I'm pretty sure there are 2 versions of this board, one having an RCT6 labeled on the processor and another with RET6. I believe the latter is associated with a 512k onboard flash rather than the 256k flash found on the RCT6 model. I'm not sure, but it looks like the build environment he is using in the video would work for the 512k variant, but maybe not the other? Someone let me know as I am a little worried with choosing which one when compiling.
I put one of these in on Sunday with the E35 touchscreen, the silence is amazing, there are a few horror stories on Reddit where they fail but still worth the effort to just drop in.
I installed this and I'm getting a "no printer attached" notification on the touchscreen board. Can't move it tried going through all cables with no luck. Any ideas will be helpful.
I had serious issues at the start trying to connect the BL touch because the company I bought it from on Amazon used RED for ground... So the board was going into automatic shutdown every time I booted up. Once I switched the wires around it worked.
Finally thinking about doing some upgrades to my machine. Thank you very much for this video, I am positive it will come in handy soon. This, a bltouch, and a few other little things are in the very near future for my Ender 3.
I Also purchased and installed an SKR Mini E3 V 2.0. Now I need quieter fans. One thing you did not mention was that the positive voltage and ground terminals are backward when compared to the original Creality board. This applied to the input voltage, hotend fan, hotend heater, bed heater and the BLtouch servo connector. I had to re-wire the BLtouch's 3-pin connector due to this polarity reversal relative to Creality's original BLTouch upgrade kit. Also, there is another firmware file in BTT's github which does use the BLtouch as the Z-axis endstop, without requiring the original Z-axis endstop be present.
One advantage would be that the drivers are seperate on the 1.4. So if one breaks you don't need to replace the whole board. And there are 5 instead of 4. PS: I'm also looking for either the 1.4 turbo with 2209's or the mini. Now that the mini 2.0 is out, the choice is even harder.....
Cookie with the cost only being $35 it’s a non question. I assume the drivers are inexpensive? Guess it all depends on if you want the newer board. Assuming your not running dual extruders.
Just finished installing this on my Ender 3 Pro. The steppers are now eerily quiet! Thanks for the checklists, they helped a lot and it all worked the first time. Keep up the great work! Shipping to me in AU (Brisbane) took 5 weeks, so it seems shipping is getting back to normal now.
Wow I just installed this last night and it’s working great so far. I have the EZABL so I had to do a little extra work with the firmware. My direct drive arrives tomorrow which I purchased because of your MDD video. I also printed the HMG5 with dual 5015 fans. You’ve taken my printer way farther than I ever thought it could go.
Thank you for this tutorial and all your work.. just one little thing to correct.. the wiring diagram, you say that bed thermistor wires are white/white.. well them, mines at least, are black/black. Thank you again!!
Bit late to the party, but just installed one on my Ender 3 (original version). Wow!!!!! I know everyone says how much quieter the steppers are, but didn’t quite believe just how much quieter!
I ordered this the same day I ordered my Ender 3 Pro. I like the board - much quieter than the OEM part, more features, etc. I installed a bltouch v3.1 and wanted to keep my z endstop, so I tried to use the probe ports as indicated in the manual (the "1st way" as indicated in the video). This never worked with the BTT-compiled firmware or my own custom Marlin build: the probe would self-test, deploy/retract, but WOULD NOT TRIGGER at all. I checked, re-checked, and checked the wiring again - it was all correct. I plugged the probe wires into the z endstop pins, et voila! it worked. YMMV.
This has always been kind of a problem with every BTT board that has both a Z-endstop and a Probe pin. I can't remember the details correctly but the way the firmware is written you needed to do some hacky changes to the code to make it work the way you want. I think there have been attempts at introducing config settings to change the behavior but I'm not sure what's the current status since my printer has been down for a couple months.
Was it difficult to add the BLTouch to the Ender 3 install? Did you use the pre-made firmware or did have to compile your own? Great videos BTW! Very helpful!
Many thanks for this video as to the next step on my CR-10 Mini. I am so tired setting up the glass bed everytime I print. I wanted to do the next logical step and this seems to be the one; one that I can grow a step at a time. Will research your vids on compiling and the editor to use. Thanks again!
Hi! I just installed this board using your video as a guide. I'm very pleased with the results! Much quieter, better onboard OS, and room for upgrades! Thanks for the content!
Wow!, Kudos to you! i have never been able to compile a firmware with VSCode, you were the first to actually make a step by step which included the copying over of the config files,.. duh,.. after the fact. I am an owner of an Endor 3 Pro for three weeks now and have acquired two rubber duckies already! LOL,.. the mini E3 works like a charm and prints better as well. I encourage everyone to look at your calibration page on GitHub along with your other great you tube pages on maintenance and upkeep. The only thing left now is to print print print. Who knows?, maybe ill break out my old GoPro and look into a Raspberry Pi. Thank you so much for maintaining such a great resource. Even a dumb dumb like me feels like a technical Guru! LOL
Thank you, Michael. I would really like to see actuation of the LED light indicators on the board if possible. When the features activate, they light up certain lights, etc. Where they are, what color they are, and what they represent. Thanks again.
Very good guide! It helped me a lot to configure the new Board. Sadly the Neopixel Workaround does not work anymore, because the Repository has changed in that specific code snippet.
Thanks a million for this - been waiting for a good review and walkthrough :-) The changes make sense and might make it into my printer now :-) Thanks again.
thank you for this video. I just received the board and with your help I feel more positive of making all the correct changes in the software. thank you once again.
Good luck getting the EZABL Pro working with this board. TH3D's support page only points to a "Vanilla" support web page on compiling your own firmware. Only problem is the config from BTT has bugs, and building the config directly from Marlin also failed as a result from bugs within PlatformIO. Considering that BLTouch is supported directly from BTT, I would STRONGLY recommend users follow that route.
Thx. own my ender a couple of weeks and the bed warped. So I decided to go for a board upgrade together with the bltouch(easier and hassle free firmware upgrades as a bonus)
Thank you so much for these videos. I just bought an ender 3 pro and you have made my learning curve much shorter. Do you know if the SKR Mini E3 V2.0 will work with an EZABL sensor instead of the BLTouch?
buy the ender 3 they say its dirt cheap they say then pow you end up spending more just on upgrades lol. I recently brought my first 3D printer ender 3 pro and i really do love everything about it and love just how much to can add to it thank you for this video i was not sure weather to go with the v1.2 or v2 board but i ended up going for the v2 as it just makes sense now i got the fun task of trying to fit it but that really should not be a problem i am mostly looking forward to the mesh leveling feature as the manual level process is a massve pain in the ass to be honest
It looks good. I recently installed a 4.2.7 board with CR touch and touch screen. Touchscreen is awesome but I’ve lost e-steps, accelerations, etc. Does this V2.0 board and its open-source firmware support touch screen?
Great video! subscribed! im planning to do this upgrade very soon together with the bltouch. that said, is there a specific version of bltouch for this board? (v1,v2,v3) and do i still need the pin adapter that comes with the bltouch kit?
Awesome vid! Just out of curiosity when do you need to format the SD card to FAT32? I noticed you say do that in some other videos when uploading marlin.
How did you code the neo pixel effects? Are they right in thr firmware? I'm used to creating my own code or using the fast led library. Great video though
Another great mainboard video! I would really like to see a comprehensive comparison to the SKR V1.4 Turbo. The V1.4 Turbo appears to be about $10 more, so is it worth it? Especially on an Ender 3?
The SKR V1.4 is a much more capable board. This is designed to be more plug and play/convenient. If you have grand plans for adding dual extrusion something like the V1.4 would be better but for most people this will be fine.
Another good video Michael, but I have the SKR-Mini-E3 V2.1 and would like to know if it's worth the trouble of upgrading again to the version 2 board?
I know I'm a year late but have the SKR Mini V3 and TFT in my cart ready to go. Biggest question is I am assuming I can use this in my Ender 3 S1 or am I mistaken? Thanks for all your videos! Subscribed straight away.
Would you be able to use this on the CR-10s as well? Since it has dual Z it seems very favorable. And thank you for all the amazing content! I would have given up a long time ago if it weren't for your channel!
Thanks for the video. Complete noob looking to upgrade the board on a CR10 S5. I also have an Anet A6 that arrived with a broken frame and no controller. I ordered it from GearBest. They shipped me a return from an Amazon Warehouse in Arizona, that had been dis-assembled broken/damaged and shipped in a Pampers Baby diaper box. 3 months later and GearBest and PayPal say I have to ship it back to China for a refund at my expense. Shipping is $128 for a refund of $119. I'm thinking the mini E3 will fit my needs as I don't need a lot of expansion. Does it support thermal protection for hot end and heat pad? How about print resume after a power failure? Lots of thunder storms here in Central Fl. Thanks again, Ken
That is a nice looking flex plate you have on your ender, I see that BTT are selling one just like it and they're very cheap compared to other options when things like shipping are considered, I would be quite interested in hearing about how it's working for you.
Because I use this video OFTEN as a reference for this board, here are some bookmarks:
0:57 - What is the BigTreeTech SKR Mini E3?
2:21 - What is Different From V1.2 to V2.0?
4:09 - How do you install the mainboard?
4:57 - Compatible out of the box?
6:11 - How can you compile your oen firmware?
8:39 - How does the new EEPROM work?
9:01 - BLTouch Compatible?
10:42 - Filament Runout Compatible?
11:45 - Neopixel and other accessories?
12:59 - TFT35 Dual Mode Touch Screen
13:37 - 3d Printer Wifi
13:43 - UPS
13:55 - How to activate sensorless homing?
15:07 - End summary
you are my hero for today.
thank you kyle! i just finished the long install of all 3 e3pro upgrades and bounced between 3 vids because theres a dif nugget of info in each vid...nothing worked right and i flashed and no ttft display after flash...wracked my brain...drank went to bed...double checked every wire config...bltouch connection wires red and blue were flipped...fixed...found out the damn reset button on the display was being pressed by the factory mount...WHY?! now i sit here dumbfounded and yep...
@@507helmet I had the same problem, took some measurements, went to my very cold shop, drilled a 3/8" hole in the bracket, problem solved.
Kyle, I found this on the listing on Amazon.US for this board
2)Because the fan on the SKR Mini E3 V2.0 control board is a CNC fan, you need to set the wind speed before using it. (Note: V2.0 version of the fan is not ready to use after power on)
This looks like BS to me as I can't find any documentation online to support this claim, I did however find issues of people receiving boards with faulty MOSFET's and think this could be some type of getting out for the retailer trying to make people think they have done something wrong with their board,
My board worked fine out of the box
thanks man, so freaking helpful. skipped half the video just to listen to the part i needed to in 2 seconds :)
I love how your intro is exactly ten seconds long, so I can double tap through the intro as I binge watch these videos
One other fancy thing you can do is press L. J and L shift it by 10 seconds rather than 5 =D
@@thebasketofgoods9753 I think he was meaning on mobile
KONO DIO DA oh okay. That makes sense too.
Either way, good intro to use time skip on =3
Another great guide. I swear, you’re carrying the ender 3 community. I’d have never bought one if not for detailed guides like this. It’s a good thing you’re a science teacher, because you’re great at it!
You'd never have bought the Ender 3 if it weren't for these guides? Don't get me wrong, Michael has the best guides on UA-cam, but the Ender3 has been the best value FDM printer for the last 2 years running.
Heroman I mean that I learned about the printer through Michael
@@Drakoman07 same here and I agree with what you said (in an odd backwards type of way). I bought the ender 3 based on lots of research with his being very helpful.
In hindsight, I would also say "id never have bought one either if it wasnt for micheal. aka: i wouldve had a teribble time trying to figure it all out and probably given up bc well all know DesignProtoypeTest isnt about to put in half the work towards being as helpful, detailed and budget friendly. Not everyone can just up and spend $300 on duet and 5' screen since i spent 2/3rds of that on the printer itself
My son chose to buy the Ender 3 Pro in August based on channels like this and the comments from owners. We've had a straight forward climb from build to very high quality prints in multiple filament types and never looked back. I'm extremely grateful to this channel and the comments from users about their experiences and ideas. There is no way the journey would be as easy as it has been without all of you. Yes it's a bunch of work, careful watching and reading etc, but still no big issues of any sort, and the print quality,,, wow. We upgraded during the build process ( extruder, bed springs,and wheels etc ) , I can't say enough about the value of the learning process , maintenance details and understanding the role of each component that this channel has provided. We use Solidworks to design, those drawings are done very differently had we not had the overall printing experience the Ender ( any good printer ) has provided. It forced us to do small upgrades incrementally and really understand printer setup and tuning adjustment. Best Wishes to all who contribute and Thank You !!
I recently bought an Ender 3 (my first 3D Pinter) and was looking for ways to upgrade it. I started watching your videos while researching printers. Once I got it and started printing, I knew I wanted to quiet it down. So I got the SKR Mini E3 v2.0 and TFT35 E3 V3.0 and installed them. Holy shiznit! It’s so much quieter. The touch screen feels like it belongs in this century. Now I’m looking forward to add a BLtouch and filament run out sensor.
I just wanted to let you know that your videos have been helpful and informative as I venture into this new hobby. So, thank you and keep making great videos. :)
I also just bought the Ender 3 as my first printer, will be building it this weekend. I also am strongly considering at a new motherboard adn agree this channel has many helpful videos. :-)
So after installing the SKR Mini E3 v2.0 I was still having trouble with first layer stick and bed leveling in general. I'd already ordered a BLTouch v3.1 and it arrived a couple days ago. So I got it installed along with the firmware available from BTT on github. It took me a little bit to get things figured out but now prints are sticking and I'm getting consistently better results. Yay! :)
@SereneScream considering it too. I have bed adhesion issues as well, have to use the z babystep on the first layer to Get good adhesion then turn it back. Its a pain in the ass
The biggest problem with this upgrade: After you install it, everything else on your printer seems LOUD. Especially the board cooling fan. Which means you'll need to swap those things out, too :D
github.com/StevenCreations/Marlin2.0.x_SKRE3 here is my bin file the hast fast bed leveling and no bugs unlike the big tree tech bin files on github. no issues at all. check your wiring if they are still loud
@@steveandre763 Does your firmware use the BLtouch as a Z stop?
@@steveandre763 Are you able to answer the question Balan had? Does your firmware use the bltouch as a z stop?
@@steveandre763 LOL He means since the stepper drivers are silent the fans SEEM loud, not that they are louder.
I'm brazilian and love how many Ayrton Senna's t-shirt you have.
I remember watching him race in the '84 Dallas Grand Prix, he was an incredible driver.
Worlds greatest to date
I'm American and I agree! Not only one of the greats on track, but off track as well!
@@myphone7568 did a lot for the sport pushing safety real modern day legend
After that your looking back to the days of jim clark to find more legends
As a person that has owned an Ender 3 for less than 24hr, I was able to drop this into my stock unit without any issues. Massive improvement to noise and really happy to see you've tested out a lot of the popular upgrades!
Side note: Awesome channel. Been very helpful with me dipping my toes into 3D Printing!
My son and I are in the process of purchasing our first 3D printer and have narrowed it down to 3/3 Pro/5. How user friendly is the 3 for first timers?
@@bocconom i just got an ender 3 pro a few weeks ago (for the price its so worth it) , easy to assemble (you shouldn't get stuck but if you do youtube has alot of build guides for all models!), the hardest thing is probably getting the bed level, its not hard to do, but make sure you put in the time to make sure it is as close as you can get it, again youtube guides help you, but once you've done that, its literally load filament choose your model and print it! :D always watch your first few layers to make sure it sticks to the bed! if you ever get stuck theres so many videos on here for 3d printers to help you! good luck
@@bocconom Very very friendly for first timers. I'd argue that it's probably the best printer for a first timer.
@@Mr-ZinK Thank you much. Did you do any other upgrades?
@@leopshef I think we have settled on the 3 Pro. Thanks.
I have a stock Ender 3 Pro. I didn't know it could be upgraded with sensor-less homing, wi-fi or a touchscreen! This video is awesome. I will definitely be looking for the upgrade parts per your recommendations. I'm just as excited to modify the printer as using it to make 3D prints. I really enjoy my Ender 3 Pro and I'm a complete newbie to this hobby (that's what it is for me at the moment). But, I really like designing my own parts to fix things around my home and simply trying out new ideas. I have a sincere trust in your information because you demonstrate how thorough you are and that's incredibly important to me. After I watch your videos, I don't have to guess at what choice to make. I simply have to decide where to buy from. Thanks for your continued efforts on the Ender 3 Pro and please continue to educate those of us looking to learn more about the printer itself and printing techniques, tips, etc. Thank you.
I'm glad my creality silent board order was canceled last month. I'm going to pick one of these up instead!
Bought a silent board, had weird-a** unfixable extruder bugs, returned it and bought this board instead !
I bought the mini E3 largely because of your video, and I was blown away by how much better the printer performed with it compared to the stock board, particularly regarding noise. I've recommended it to a couple friends as the first upgrade they should buy for their printer, and they've been happy with it as well. Through my journey in printing I've watched your videos, so thank you for helping educate me and many others in the community. I started looking deeper into duet boards a week or two before your video on them, and they seem quite promising and offer several things that marlin doesn't have yet; it would be interesting to see how using a duet in an ender 3 impacted performance and usability. Happy Printing!
I was literally just considering buying this and looking up how to install. Thank you!!
Blade Ron SAME
Got one delivered one day before this vid went up. On an Ender 3 it's just plug and play, and since I already have an SKR 1.3 running my AM8, I think I could have figured out how to get sensorless homing and the Bltouch to work, but now I don't need to anymore. :]
Gerd L. Plüü it’s an awesome upgrade when u think that the 1.1.5 costs more then this board and. (Skr have better driver too)
Great video Michael, I just got the BTT SKR Mini v1.2 and I am extremely happy with it, This new upgrade looks like a great upgrade. Thanks for sharing this video.
Same here with the 1.2, only had it for 2 weeks and watching this makes me want to get the V2.0 now!🤦♂️ more money😫
hey man what is the difference for you?
@@dcf476 there is no reason to upgrade from 1.2 :)
I've just upgraded my Ender 3 pro to the SKR min V2.0. Only 2 small issues when using octoprint. I didn't get any comms via the USB port, I'm using a pi 4 and the USB operation has changed. Evidently you need to add "over_voltage=1" to /boot/config.txt of the pi, I had no issues with the stock ender board and the pi so it must be different on the SKR card.
Secondly, something I was going to get around to on the previous board but didn't was to put a slither of polyamide/kapton tape on the +5v contact on the USB cable so the pi is not powering the main board. I had false overheat protection alarms from the printer if you turn the main power off on the printer with the nozzle still hot. I didn't get that with the previous board so assume overheat protection wasn't enabled although the version of firmware supported it, it was the stock Ender firmware. I believe thre are other issues around powering the board form the pi, here's a good reference github.com/bigtreetech/BIGTREETECH-SKR-mini-E3/issues/41
I just ordered Ender 3 for my 1st 3d printer. Can't wait to explore and upgrade after seeing your videos. Thanks for your channel!
My suggestion is to buy a lot of filament. And check out this build video and the one from CHEP. Did you notice that the ender 3 pro is now on sale for $209?
Watch a few build videos I think it was 3d print tomb or something like that saved me sooo many potential heart aches... And start watching a vid on bed leveling when ever in the bathroom
i would love to see a video of converting a creality machine with dual z steppers into dual z endstops like what a i3 mega has. unless there is a better alternative. great video as always
I used this video a while back to updage my ender3. I came back just for the dragon clip to test my new prusa, and you desrve the views. Amazing work man. Glad your still at it.
For those who bought the board for Creality printers: Remember that the positions of the mainboard fan plug and the parts cooling fan plug are switched on the SKR E3 v2.0 and the Ender 1.1.4 mainboard. This is also shown in the wiring diagram but I think it's not directly mentioned in the video.
thanks for mentioning that
I was exactly looking for this information... I noticed the discrepancy between the cabling on the original Enders board and diagram shown in the video. Thanks!
didnt work for me
@@bobf3598 what didnt
Is the hot end fan supposed to be turned ON all the time? If not, how can I fix it?
Great video - just ordered myself one of the new boards, a wifi dongle and TFT35. Glad I waited and didnt just grab the 1.2 like I was going to!
FYI, the little paper insert in my SKR Mini E3 V2.0 box has a link to this video. :D
Done! The noise difference and driving smoothness is astounding. I'm going to order silent fans for the motherboard enclosure and the PSU because now they sound loud as heck in comparison.
I installed one of these as a retrofit on a Wanhao I3 Plus this weekend, and the only thing I haven't gotten to work is using the second fan connector to be a auto hotend fan.
Defining it as the auto fan, it powers up on startup. Other than some pid tuning for the bed and hotend, it's working well with a bltouch also. I didn't bother with sensorless homing.
how noticeable the improvement?
Picked this up a few days after it came out. LOVE the results I’m getting with it, especially the reduction in noise. Wish I had this guide when I installed it, but forced me to learn.
Just installed the v2 in my ender 3 pro and I'm pretty happy aside from two issues. 1: clicking Stop Print does not immediately stop the print. I have no idea why but there is often a delay between 10 and 30 sec before the print stops and while I don't use this much, when I want to stop a print, I want it stopped NOW! 2: It may be the lack of motor sound but now the other fans sound SUPER loud. This second one is less a serious issue but any ideas on #1 would be greatly appreciated. Love the channel.
Thank you for making this video. I have been going a little crazy trying to figure out why my bltouch isn't work when I try and do a z homing when it is plugged into the probe socket. When someone told me I no longer need the Z endstop. Now I can see that I do need the Z endstop. Thank you it has been most helpful.
4:31 in the diagram the label for G and I should be switched around. had this problem that my part cooling was always on, but now when i switched it up the "G" should be in the "I" it worked normally Please take note of this!
Also E should read black/black and not white/white (at least on my printer)
Also, on the SKR diagram, connection B ... the wires shown are the wrong way round. Positive is closest to the side of connection C, not H.
Michael, I like your channel content, you are always providing good info. Also, it is nice to see that you are an F1 fan too. Glad that the new season starts this weekend.
I'm very excited about F1 finally being back. Need to get some McLaren merch ready for Dan Ricciardo's switch next year.
Teaching Tech yeah Daniel is one of my favorite. Hopefully McLaren can come back a give Daniel the tools to take the fight at the front
4:29 - Just a heads up that at least on an original CR-10, "B" in your diagram is backwards. I don't know if the polarity is reversed on the SKR board or on the bed heater relay. Either way, after getting a bed heating error I swapped the red and black and it now works fine.
After you installed the board in the CR10 did you have to compile new marlin firmware, or did it work out the box?
@@chrisstock5210 Yes. I had never taken the time to understand all of the Marlin firmware so it was a good exercise. There's a reddit post on building the firmware for Ender which I followed but started with the generic Marlin Example Config for Cr-10 and retained all the CR-10-specific items, mostly bed size/dimension related config.
Thank goodness for you! I couldn't figure out what was wrong. Now I'm set after swapping those 2 wires!
This is such an amazing upgrade, buing this with a BLtouch has saved me from having to install a bootloader, and it made it incredibly quiet. Definitely worth the money.
@teachingtech will you do a video on the BTT skr mini e3 v3.0?
Is it that much different?
Awesome! I've had motor dampers but without heatsinks and the motors are crazy hot. I put off buying the v1.2 and now here's a better version!
You'll need to install the Platform IO extension in VS Code in order to get the tick option at @7:10!
Thanks! I was wondering why this wasn't mentioned in the video...
@@doctorsnaketown I think because as you get into the Maker world it turns out to be a popular plugin for using VS Code to program stuff like arduinos and other microcontrollers. But if this is your first entry into that world then (like for me) it is definitely hard to know 🤣
Nice, I just put one of these in my cr10 mini a couple of weeks ago. A great board. With bltouch I had to swap red and yellow wires in the plug to the board
Something to keep in mind: I'm pretty sure there are 2 versions of this board, one having an RCT6 labeled on the processor and another with RET6. I believe the latter is associated with a 512k onboard flash rather than the 256k flash found on the RCT6 model. I'm not sure, but it looks like the build environment he is using in the video would work for the 512k variant, but maybe not the other? Someone let me know as I am a little worried with choosing which one when compiling.
I put one of these in on Sunday with the E35 touchscreen, the silence is amazing, there are a few horror stories on Reddit where they fail but still worth the effort to just drop in.
I installed this and I'm getting a "no printer attached" notification on the touchscreen board. Can't move it tried going through all cables with no luck. Any ideas will be helpful.
Ty
Solved update touchscreen firmware
Mine shows that until the mainboard finishes booting up. Takes maybe 5s or so.
I had serious issues at the start trying to connect the BL touch because the company I bought it from on Amazon used RED for ground... So the board was going into automatic shutdown every time I booted up. Once I switched the wires around it worked.
Finally thinking about doing some upgrades to my machine. Thank you very much for this video, I am positive it will come in handy soon. This, a bltouch, and a few other little things are in the very near future for my Ender 3.
I can't understand the software upgrade. I watched all the other videos at least 10 times. Damn.
I Also purchased and installed an SKR Mini E3 V 2.0. Now I need quieter fans.
One thing you did not mention was that the positive voltage and ground terminals are backward when compared to the original Creality board. This applied to the input voltage, hotend fan, hotend heater, bed heater and the BLtouch servo connector. I had to re-wire the BLtouch's 3-pin connector due to this polarity reversal relative to Creality's original BLTouch upgrade kit. Also, there is another firmware file in BTT's github which does use the BLtouch as the Z-axis endstop, without requiring the original Z-axis endstop be present.
I provided colour coded wiring diagrams. I don't know what else I can do beyond that? If people ignore them that's beyond my control.
I so wish that I bought one of these instead of the 1.4 turbo for my cr-10 mini!
That is probably better than this
Buy one then u have both ther both good
Thank you for this great guide. I really love the style, with just the details I need, and the perfect explanations. Very instructive.
Is there a reason or advantage to buy a SKR 1.4 turbo and 2209's over the SKR mini?
One advantage would be that the drivers are seperate on the 1.4. So if one breaks you don't need to replace the whole board. And there are 5 instead of 4.
PS: I'm also looking for either the 1.4 turbo with 2209's or the mini. Now that the mini 2.0 is out, the choice is even harder.....
Currently I have to make the same decision :D and I have no Idea which one...
If you are planning big future upgrades like switching to dual extrusion, the V1.4 will be better. In most case the mini will suffice.
Cookie with the cost only being $35 it’s a non question. I assume the drivers are inexpensive? Guess it all depends on if you want the newer board. Assuming your not running dual extruders.
Just finished installing this on my Ender 3 Pro. The steppers are now eerily quiet! Thanks for the checklists, they helped a lot and it all worked the first time. Keep up the great work!
Shipping to me in AU (Brisbane) took 5 weeks, so it seems shipping is getting back to normal now.
You missed one new feature: support for a second Z-axis motor.
3:34
@@TeachingTech OK, I missed it 😁
Wow I just installed this last night and it’s working great so far. I have the EZABL so I had to do a little extra work with the firmware. My direct drive arrives tomorrow which I purchased because of your MDD video. I also printed the HMG5 with dual 5015 fans. You’ve taken my printer way farther than I ever thought it could go.
FFS! I'm unsubscribing! This is costing me a fortune watching these and buying everything because you're making them look like great upgrades. Lol.
it is a great upgrade though... I'm getting it mostly for the extra flash storage so I can use bltouch
although most of the upgrades are a waste, like linear rails. Ender 3 has such good quality with extrusions, why change it?
dude Im literally applying for a new job with the sole motivation that this new position can fund my projects better lmao
@@anglerfish61 thats what we live for 😂
@@ilyas5708 yes 😂
Thank you for this tutorial and all your work.. just one little thing to correct.. the wiring diagram, you say that bed thermistor wires are white/white.. well them, mines at least, are black/black. Thank you again!!
Bit late to the party, but just installed one on my Ender 3 (original version). Wow!!!!! I know everyone says how much quieter the steppers are, but didn’t quite believe just how much quieter!
Proved very helpful not only in setup but choosing what direction to go with my Ender3. Thanks for putting such great how to videos together!
Finally, I have upgraded my cr 10 mini with board and steppers are running smoothly with no jerks and noise. I am happy with this upgrade.
How would I add a creality lazer please and thank you love your channel and all you teach
I ordered this the same day I ordered my Ender 3 Pro. I like the board - much quieter than the OEM part, more features, etc. I installed a bltouch v3.1 and wanted to keep my z endstop, so I tried to use the probe ports as indicated in the manual (the "1st way" as indicated in the video). This never worked with the BTT-compiled firmware or my own custom Marlin build: the probe would self-test, deploy/retract, but WOULD NOT TRIGGER at all. I checked, re-checked, and checked the wiring again - it was all correct. I plugged the probe wires into the z endstop pins, et voila! it worked. YMMV.
This has always been kind of a problem with every BTT board that has both a Z-endstop and a Probe pin. I can't remember the details correctly but the way the firmware is written you needed to do some hacky changes to the code to make it work the way you want. I think there have been attempts at introducing config settings to change the behavior but I'm not sure what's the current status since my printer has been down for a couple months.
My patrons tell me that particular work around has been implemented in Marlin now. Fingers crossed it's easier moving forward.
Was it difficult to add the BLTouch to the Ender 3 install? Did you use the pre-made firmware or did have to compile your own? Great videos BTW! Very helpful!
Many thanks for this video as to the next step on my CR-10 Mini. I am so tired setting up the glass bed everytime I print. I wanted to do the next logical step and this seems to be the one; one that I can grow a step at a time. Will research your vids on compiling and the editor to use. Thanks again!
Hi! I just installed this board using your video as a guide. I'm very pleased with the results! Much quieter, better onboard OS, and room for upgrades! Thanks for the content!
Wow!, Kudos to you! i have never been able to compile a firmware with VSCode, you were the first to actually make a step by step which included the copying over of the config files,.. duh,.. after the fact.
I am an owner of an Endor 3 Pro for three weeks now and have acquired two rubber duckies already! LOL,.. the mini E3 works like a charm and prints better as well.
I encourage everyone to look at your calibration page on GitHub along with your other great you tube pages on maintenance and upkeep. The only thing left now is to print print print.
Who knows?, maybe ill break out my old GoPro and look into a Raspberry Pi.
Thank you so much for maintaining such a great resource. Even a dumb dumb like me feels like a technical Guru! LOL
Thank you, Michael. I would really like to see actuation of the LED light indicators on the board if possible. When the features activate, they light up certain lights, etc. Where they are, what color they are, and what they represent. Thanks again.
Very good guide! It helped me a lot to configure the new Board.
Sadly the Neopixel Workaround does not work anymore, because the Repository has changed in that specific code snippet.
Has anyone figured out a fix for this? Really want to use some.
Try the newest version this seems to work for me, at least I am able to compile it after installing git on my machine.
I’ve instaled two weeks ago... awesome. Thanks for the video.
Nice shirt, I bet the fans here from Brazil enjoy seeing it!
I installed mine a few weeks ago and it has been working great.
Thanks a million for this - been waiting for a good review and walkthrough :-) The changes make sense and might make it into my printer now :-) Thanks again.
Amazing, precise and concise review. I was about to buy 1.2 but I managed to cancel the order and switch to this instead!
Perfect timing! I ordered one of these recently and it's coming in soon!
Great Video, Just installed this board on my Ender 3 Love the silent drivers, can't wait to install the smart filament sensor and BL touch probe
Just bought one following your advice. It's excellent, so much quieter.
Man good timing i just got the board yesterday and need to put it in my ender 3 pro
thank you for this video. I just received the board and with your help I feel more positive of making all the correct changes in the software. thank you once again.
Fantastic guide. I'm going to refer to it often when my printer and mods arrive.
What a coincidence, mine came in the mail today! Thanks for making these videos.
Ordered it just now because my 1.2 X motor stopped working... Can't wait for it to arrive!
Wow thanks. I came for the Sensorless homing part. Had it working in minutes. 50/50 worked well for me as well.
Good luck getting the EZABL Pro working with this board.
TH3D's support page only points to a "Vanilla" support web page on compiling your own firmware.
Only problem is the config from BTT has bugs, and building the config directly from Marlin also failed as a result from bugs within PlatformIO.
Considering that BLTouch is supported directly from BTT, I would STRONGLY recommend users follow that route.
Been waiting for this guide! Loving my 2.0
here is my bin file the hast fast bed leveling and no bugs unlike the big tree tech bin files on github.github.com/StevenCreations/Marlin2.0.x_SKRE3
Thanks, another timely video, I too have one, and a BLTouch, coming Tuesday. Like so many others....$200 printer with a gazillion in upgrades.
I ordered mine bundled with the TFT35 v3. Pretty awesome.
The video is great and a wonderful reference, however have you done a video connecting the skr mini e3 v2 with the BTT 24v ups?
Perfect timing! I literally have this 2.0 arriving in the mail tomorrow and will be rewatching this for the install. Thanks!
I just got mine today and said to myself "I wonder if Teaching Tech has an install video yet?"
I just ordered this board after seeing your video, can't wait to see it in action :D
Thanks Michael! Great content as always. I might just upgrade my stock CR-10 finally. This sounds like a pretty good replacement.
Thx. own my ender a couple of weeks and the bed warped. So I decided to go for a board upgrade together with the bltouch(easier and hassle free firmware upgrades as a bonus)
Thank you so much for these videos. I just bought an ender 3 pro and you have made my learning curve much shorter. Do you know if the SKR Mini E3 V2.0 will work with an EZABL sensor instead of the BLTouch?
I just wanted to buy the ender silent board and you upload this video. Legend
buy the ender 3 they say its dirt cheap they say then pow you end up spending more just on upgrades lol. I recently brought my first 3D printer ender 3 pro and i really do love everything about it and love just how much to can add to it thank you for this video i was not sure weather to go with the v1.2 or v2 board but i ended up going for the v2 as it just makes sense now i got the fun task of trying to fit it but that really should not be a problem i am mostly looking forward to the mesh leveling feature as the manual level process is a massve pain in the ass to be honest
Literally ordered this on the weekend.
Hello Michael the SKR Mini E3 v3.0 is out! you can make an updated Guide?
It looks good. I recently installed a 4.2.7 board with CR touch and touch screen. Touchscreen is awesome but I’ve lost e-steps, accelerations, etc. Does this V2.0 board and its open-source firmware support touch screen?
Great video! subscribed! im planning to do this upgrade very soon together with the bltouch. that said, is there a specific version of bltouch for this board? (v1,v2,v3) and do i still need the pin adapter that comes with the bltouch kit?
Awesome vid! Just out of curiosity when do you need to format the SD card to FAT32? I noticed you say do that in some other videos when uploading marlin.
How did you code the neo pixel effects? Are they right in thr firmware? I'm used to creating my own code or using the fast led library. Great video though
are you kidding me, i just got my SKR Mini E3 v1.2 working literally yesterday, loll. Great video, as always.
My V1.2 has been perfect fort a long time so don't despair.
Did you get neo- pixels working ?
I'm getting an Ender 3 Pro on Saturday. Is this upgrade recommended for the Pro version? As always, a fantastic info packed video!
@The Technology Technician Thank you!
Another great mainboard video! I would really like to see a comprehensive comparison to the SKR V1.4 Turbo. The V1.4 Turbo appears to be about $10 more, so is it worth it? Especially on an Ender 3?
The SKR V1.4 is a much more capable board. This is designed to be more plug and play/convenient.
If you have grand plans for adding dual extrusion something like the V1.4 would be better but for most people this will be fine.
@@TeachingTech Thanks for the response. That's what I needed to know!
Cool board. Another great video. Thanks for doing these.
Another good video Michael, but I have the SKR-Mini-E3 V2.1 and would like to know if it's worth the trouble of upgrading again to the version 2 board?
I know I'm a year late but have the SKR Mini V3 and TFT in my cart ready to go. Biggest question is I am assuming I can use this in my Ender 3 S1 or am I mistaken? Thanks for all your videos! Subscribed straight away.
Would you be able to use this on the CR-10s as well? Since it has dual Z it seems very favorable.
And thank you for all the amazing content! I would have given up a long time ago if it weren't for your channel!
Thanks for the video. Complete noob looking to upgrade the board on a CR10 S5. I also have an Anet A6 that arrived with a broken frame and no controller. I ordered it from GearBest. They shipped me a return from an Amazon Warehouse in Arizona, that had been dis-assembled broken/damaged and shipped in a Pampers Baby diaper box. 3 months later and GearBest and PayPal say I have to ship it back to China for a refund at my expense. Shipping is $128 for a refund of $119. I'm thinking the mini E3 will fit my needs as I don't need a lot of expansion. Does it support thermal protection for hot end and heat pad? How about print resume after a power failure? Lots of thunder storms here in Central Fl. Thanks again, Ken
Thanks man! Your channel is always there when I want to install an upgrade in my printer. I don't know what would I do without your great videos :)
That is a nice looking flex plate you have on your ender, I see that BTT are selling one just like it and they're very cheap compared to other options when things like shipping are considered, I would be quite interested in hearing about how it's working for you.
I've installed this version on my Ender3. Good product.
Hi Yohann. Can you remember which port you installed the Z stepper? On the wiring diagram its not clear if this should fo into ZBM or ZAM ports.
Man I was hoping for this video. Just ordered mine off of Amazon now.