Absolutely gorgeous truck I just picked up a 1999 ford f250 crew cab short bed xlt 5.4 v8 I wish it was a 7.🌲 I’m going to mod it out I don’t know what mods to do otherwise beautiful truck ❤❤❤❤
I got it from a customer I did bodywork for and had to plastic weld stuff on it, it’s a eBay special off a 2008-2010 ford f-250 4x4 there’s no cutting but it will not bolt on because it doesn’t line up to metal, you have to zip tie it to inner bumper brackets sadly but it’s still sturdy since I put it on maybe 4 months ago
Kc300x is a nice ass turbo. Mine was the stage 3 tho with stock fuel and hpop so it didnt gain any performance just sounded nicer, if I would of done injectors etc would of been bad ass. If you got the stage 1 kc300x on stock fuel and oil I think u can get 30 psi of boost or something like that!
It looks really good. I'm not a fan of the deep dish wheels and low profile tires because I do go off road some and my wheels are somewhat similar. I have 20s that are 13.50 wide on Black Rhino wheels. I have a 2000 F250 and it has the mostly white with black wheels, tint trim, stormtrooper look, but I want to repaint it. I like your mirrors and headlights better and the valance. I have the TS-6 tuner and usually run position #4. I'm getting ready to add an HPOP, injectors and 4 inch turbo as I have 300K on mine and the cups on the injectors are wore. My trans finally went out at 305K, which was recently. However, your paint and wheels look pristine. I love my truck but I don't love the steering or suspension and want to get it upgraded with softer suspension and clean up the inside quite a bit. New seat upholstery etc. etc.
@@chadkirby5438 all I did was take bumper and grille off the truck, tape off chrome, scuff up plastic with red scotch brite pad, and spray paint black rustoleum paint on
You can still tow with the spacers and yes they fit without, only reason I have them on is because I normally run 2016 stock wheels that need the spacer to prevent rubbing and didn’t want to take them off for the wide wheels to be on for only a week or so lol
@@nick7.3 I’m 51 I’ve noticed the younger generation have really spaced some of these wheels I followed a truck the other night and I could see his rotors I’m not up on the trends it is a sharp truck
Hey man i have a question or need advise if you dont mind. I'm looking at a 96 F250 7.3 L on 37's. The truck is way too far away for me to go look at it and test drive it. The motor trans axles are all stock. My question are first do you think the truck is going to be ridiculously slow? Second do you think the 37's are going to do damage to the transmission or axles?
Im currently looking into an 02 CCLB F350 7.3 for 5700 it's an 4R100 sadly but I'd either swap a ZF6 in her or built 4r if I'd buy her. I'd prefer a CCLB OBS F350 7.3 but hey CCLB 7.3 is great imo especially since I'm a Ford guy
Yes sir I used to love an obs once you get a superduty you can’t go back. And why not just leave the stock trans? Manuals are slow and useless the auto trans on these are good af for stock in my opinion
@Nick’s Powerstroke idk I'd just prefer a manual and my build would just be mainly for towing Gooseneck but also a street truck I'd have fun with. I've been looking into a couple of 2nd Gen Cummins ext cab long beds as well for Gooseneck towing and as well as a street truck. Even though I'm a Ford guy I've always loved the older 89-08 Ram 2500/3500 Cummins Pickups
@@demetriuspalmer2992 if you do manual so it because you enjoy shifting not because you think you need it because you don’t the obs e4od are way worse than superduty 4r100
@@nick7.3 cool cool cool 🤘🏽🔥 Ik the 7.3s are good engines, at least from what I’ve been researching! I have the dually and I’m in love! It’s actually on my shorts i believe
Very nice, my friend. I’m most interested in that front spoiler thing I have under the license plate. I have an obs 250 and think that’d look great on it as well. I also want a bed cap - for securing items from theft & weather. Also, another upgrade that would look great on yours, and mine as well, cab marker lights (above the windshield.) I think they look badass
That is unfortunately correct, I had to bolt the spacer on to the truck with my factory 99 lug nuts but the lugs on spacer will only fit 03+ lug nuts so you have to buy 03+ lugs in addition to the spacers for it to work
@@nick7.3 Gotcha, i think they changed the thread. Any chance they are 14x1.5 thread? I have a whole bag of lug nuts laying around that ended up being the wrong ones
@@RichBoyLiving my 6.7 powerstroke is faster but no, you havent had less issues 7.3s are better ive tested it ive owned both trucks the 6.0L powerstroke was a failed design, why do you think ford dropped navistar?
The stance on that sucker is mint. so clean, love it.
Love the look of the truck, great video!
Thank you🤟
I would kill for this truck. I love everything but the spacers.
Thanks! I run 2016 platinum f250 stock wheels most of the time is why the spacers are on, makes it not rub when turning
What beautiful unit good job man ! Shes tons of Love ❤ keep Them Alive 💪
Bro I love this truck, literally how I want my 7.3 to be 🔥
That’s one of the cleanest 7.3s I’ve seen
beautiful truck!
Beautiful truck 😮😊 I just got me one for my landscaping company 😍 love the way it looks 👌
Nice build man !
Absolutely gorgeous truck I just picked up a 1999 ford f250 crew cab short bed xlt 5.4 v8 I wish it was a 7.🌲 I’m going to mod it out I don’t know what mods to do otherwise beautiful truck ❤❤❤❤
Badass truck new subscriber quick question do you have a link for the front lower valance? and does it just bolt on no cutting required
I got it from a customer I did bodywork for and had to plastic weld stuff on it, it’s a eBay special off a 2008-2010 ford f-250 4x4 there’s no cutting but it will not bolt on because it doesn’t line up to metal, you have to zip tie it to inner bumper brackets sadly but it’s still sturdy since I put it on maybe 4 months ago
Bad ass truck my man i just picked up an 02 f 350 with 220k im about to upgrade the turbo how is that kc300 working out
Kc300x is a nice ass turbo. Mine was the stage 3 tho with stock fuel and hpop so it didnt gain any performance just sounded nicer, if I would of done injectors etc would of been bad ass. If you got the stage 1 kc300x on stock fuel and oil I think u can get 30 psi of boost or something like that!
Nice truck bro! She's purty!
It's not though. The minute that thing goes off the road and hits a wet blade of grass it's getting stuck
@@biggus_dickkus I don't have that issue in my F250, but it's also 4x4.
Clean rig
Absolutely mint. Love it
It looks really good. I'm not a fan of the deep dish wheels and low profile tires because I do go off road some and my wheels are somewhat similar. I have 20s that are 13.50 wide on Black Rhino wheels. I have a 2000 F250 and it has the mostly white with black wheels, tint trim, stormtrooper look, but I want to repaint it. I like your mirrors and headlights better and the valance. I have the TS-6 tuner and usually run position #4. I'm getting ready to add an HPOP, injectors and 4 inch turbo as I have 300K on mine and the cups on the injectors are wore. My trans finally went out at 305K, which was recently. However, your paint and wheels look pristine. I love my truck but I don't love the steering or suspension and want to get it upgraded with softer suspension and clean up the inside quite a bit. New seat upholstery etc. etc.
I agree I only had these wheels for a week bc I preferred the stocks on 35s
I love the stance!
Thank you! Considering selling this setup for a ranch hand but we will see
@@nick7.3 how much for the whole damn truck
@@clarkwilliams9967 I couldn’t ever sell it I do have like 20 people that want to buy it tho😂
Did you paint the grey parts of the grill and lower front bumper black?
@@chadkirby5438 all I did was take bumper and grille off the truck, tape off chrome, scuff up plastic with red scotch brite pad, and spray paint black rustoleum paint on
@@nick7.3 perfect!! Thank you! I’ve been considering doing the same to my truck but have not seen what it would look like….great job…thank you!👍🏼
Nice Truck
Not a ford guy, but that trucks hot man
Do you rub at all ? Are you leveled ?
Yes it has a leveling kit and it rubs pretty bad
If you didn’t have the spacers would the 22 x14 still work I pull with mine spacers won’t work for me
You can still tow with the spacers and yes they fit without, only reason I have them on is because I normally run 2016 stock wheels that need the spacer to prevent rubbing and didn’t want to take them off for the wide wheels to be on for only a week or so lol
@@nick7.3 I’m 51 I’ve noticed the younger generation have really spaced some of these wheels I followed a truck the other night and I could see his rotors I’m not up on the trends it is a sharp truck
@@rivett40 lol thanks, I usually don’t like wide wheels I got these for cheap and know I could flip them for profit is the only reason I got them
So I just started running the same set up just different rims but how do you keep it from rubbing the rear fenders in the front
You dont, they will rub
Can you possibly explain all that you had to do to fit that valance ? Looks very good
Put it up under the bumper and zip tie thru the bolt holes on it to the brackets on the bumper
Love it dawg good job👍
Hey man i have a question or need advise if you dont mind. I'm looking at a 96 F250 7.3 L on 37's. The truck is way too far away for me to go look at it and test drive it. The motor trans axles are all stock. My question are first do you think the truck is going to be ridiculously slow? Second do you think the 37's are going to do damage to the transmission or axles?
They are mildly slow at stock and if your towing save for a transmission
Sick truck ❤🤙🏻
Thank you 🤟
Does the wheel setup rub? Is the ride harsh?
@@aoFlipMan both, it rubbed extremely bad and it did ride very rough because low profile tires
Im currently looking into an 02 CCLB F350 7.3 for 5700 it's an 4R100 sadly but I'd either swap a ZF6 in her or built 4r if I'd buy her. I'd prefer a CCLB OBS F350 7.3 but hey CCLB 7.3 is great imo especially since I'm a Ford guy
Yes sir I used to love an obs once you get a superduty you can’t go back. And why not just leave the stock trans? Manuals are slow and useless the auto trans on these are good af for stock in my opinion
@Nick’s Powerstroke idk I'd just prefer a manual and my build would just be mainly for towing Gooseneck but also a street truck I'd have fun with. I've been looking into a couple of 2nd Gen Cummins ext cab long beds as well for Gooseneck towing and as well as a street truck. Even though I'm a Ford guy I've always loved the older 89-08 Ram 2500/3500 Cummins Pickups
@@demetriuspalmer2992 if you do manual so it because you enjoy shifting not because you think you need it because you don’t the obs e4od are way worse than superduty 4r100
How are the wheel spacers on it always been scared to put spacers on a heavy duty pick up
@@ocshredders9058 Never had an issue, had them on this truck, my 6.7, and my current 2000 7.3. No difference running them on a half ton vs 3/4
The first thing I noticed was the flare on the truck bed. How's that paint holding up with those tires?
Perfect I don’t have any rock chips yet
How did you paint your valence and plastic part of the bumper ?
Scuff pad it and rattle canned rustoleum on it, the valence was stock black
That is nice 7.3
Thank you 🤝
Which 100hp tune do you run? I also have the hyrda canned tunes. I've been running 80 DD
It’s the canned tunes
@@nick7.3 I only have performance and racing on my app
What led headlights are you running?
I believe they are from “LED street light” they are super bright and we’re only like $60
Do you know the part number for them?
@@McMurrayMotors it’s these: ledlightstreet.com/products/2005-ford-f-250-super-duty-led-headlight-bulb-h13?variant=29291504533557&Google%20Shopping&gclid=Cj0KCQiA-oqdBhDfARIsAO0TrGGMdN5E66wL2nU9GgU73J-ZwPoDTKboXNwQ32wmqtp4vvyH3fP6R88aAtzBEALw_wcB
What pigtail adapter do you run for your lights?
You should make a video on the light setup in general
Where did you get them tow mirrors I want some like that but white I can’t find any for my 02
They are 08-16 mirrors I got them on ebay they are all the same
Did you have to throw spacers on the back as well?
Well naturally
The rough country stocks ride nicer when new?
Well naturally lol
@@kmeinh7097 yea the stock ones are 100% junk on any 24 year old truck
Do you have a picture of how you 2.5 lift looks on stock 20 wheels I can’t decide if I want to go with a 2.5 lift or a 4 in. Thanks
My profile picture and some other videos on my channel have 20” stocks with 35” tires
those wheels are butter, whats the specs?
22x14 hostile sprockets on 33” nitto trail grapplers
what wheel spacers did you have on this?
2” rough country
What size are your tires and rims ?
@@tveenpollard1317 22x14 wheels on 33x14 tires
how much you asking to sale? i wamt that truck
How many miles ? I have 259k on my 2001 f350 7.3 diesel! You think that’s a lot ? It was used for transport, so mainly highway miles
180k at the time of the video 259 is still gonna be going strong I wouldn’t even worry until at least 300k
@@nick7.3 cool cool cool 🤘🏽🔥 Ik the 7.3s are good engines, at least from what I’ve been researching!
I have the dually and I’m in love! It’s actually on my shorts i believe
Looks good
Very nice, my friend. I’m most interested in that front spoiler thing I have under the license plate. I have an obs 250 and think that’d look great on it as well. I also want a bed cap - for securing items from theft & weather. Also, another upgrade that would look great on yours, and mine as well, cab marker lights (above the windshield.) I think they look badass
@@ThePolishRifle thank you, not sure if this valence will fit on a obs or not its a 08-10 superduty 4wd lower valence
I have a question has anybody ever done a facelift on this truck ? I'm thinking on doing it I like the way the big lights look 😊
@@JoseLuis-b4x what face lift are you referring to? You can put any front end on these from 99-16
@@nick7.3 with the big lights
have a link for the spacers? it says they only fit 03 and up
That is unfortunately correct, I had to bolt the spacer on to the truck with my factory 99 lug nuts but the lugs on spacer will only fit 03+ lug nuts so you have to buy 03+ lugs in addition to the spacers for it to work
@@nick7.3 Gotcha, i think they changed the thread. Any chance they are 14x1.5 thread? I have a whole bag of lug nuts laying around that ended up being the wrong ones
@@blueseventhree the rc spacers are what ever thread the 03+ is
@@nick7.3 says they’re 14x1.5, you just used the regular lugs to bolt the spacers on?
@@blueseventhree I bolted the spacer to the hub with my stock 99 lug nuts
How heavy have you towed?
With this exact truck only 10
This truck is just sexy
Are you from dekalb Illinois?
No I am not I farm in Michigan, we plant delalb corn
I need a opinion should I get my truck painted all black or should I just get a brighter red
Never do all black lol
How did you put the 2008 valence on it do you have to customize the bumper a little bit
No, you have to ziptie it on tho impossible to bolt it up
@@nick7.3 oh ok thank you
@@nick7.3 also do you have to make holes in the bumper to zip tie it
@@TBFISHINGTV no I did not drill
Nice!
dude, nice
Do you have bigger injectors or are they stock?
Stock injectors
@@nick7.3 oh ok I’m surprised you didn’t run bigger injectors but she was still a very clean truck
@@dschmidt.7 thank you lol didn’t want to waste money is why
@@nick7.3 I understand that very much😂 they are a bit pricey
@@dschmidt.7 especially when it already ran good and smoked a lot anyway
Nice 👍🏼
Time for king ranch interior
I sold the truck sadly but ironically I bought a whole king ranch truck to replace it
Does the valence bolt on?
No you have to zip tie it up
What’s your average mpg?
@@dillonkizer all my 7.3s get 13-15 mpg
Sweet 7.3
Thank you!
Arnt canned tunes trash? And recommend customer tunes? Just curious
No not necessarily, im sure custom tunes could be better but I loved the canned tunes on that truck
Thats a bitchin truck 😮
What is it with the ugly wide wheels imo. Never got that fad
To look cool I ran stocks and mud tires 99% of the time with this truck ran these wheels for 2 weeks
Things bad ass
Thanks! Started off as a rotted plow truck when I got it I try to make it as nice as I can
duuuuuuude i need to get another one lol
Yes you do son
Different wheels Brap 😂
That thing is gonna sink when it goes in mud
I do not mud bog any of my trucks
nice truck. wheels: no
Check out my other videos 99% of the time I run a bubba setup was just trying something new
7.3 sucks! 6.0 for life!
@@RichBoyLiving you legit couldnt be more wrong
@@nick7.3 so why is my truck faster than yours runs better then yours and has lasted longer then yours with no issues what so ever?
@@RichBoyLiving my 6.7 powerstroke is faster but no, you havent had less issues 7.3s are better ive tested it ive owned both trucks the 6.0L powerstroke was a failed design, why do you think ford dropped navistar?
@@nick7.3 dude my truck has over 300 thousand miles on it and I’ve never had any issues get out of here with your nonsence
Those rims are trash. You and some others might like them but to me they are ugly and hold no value. Strictly cosmetic.
No value? These rims were 6k new lol
@@nick7.3 You uh......overpaid
@@cjcourter1477 no I did not lol
@@nick7.3 It's ok, we all make mistakes.
@@cjcourter1477 I didn’t pay 6 I bought them used for under 2. I just sold them a hour ago for 3,000 so clearly I know what I’m doing
That air intake is garbage
To me air filters arent a big deal, as long as it filters dust out I dont care