The XSY-AT1 you are working is a model from 2023?. I found one on amazon but its a white, maybe is from an older version. Asking so i can know wich one i should get. Thank you. Btw, what is the exact name and model the tools you are using on the 1:15 minute and also the 1:49. I wanna get those from amazon right away.
@@pureexpanseThanks. I just ordered the same vfd from amazon yesterday, also ordered the crimper. I asked the name because I'm from south America, and the translation of the tools sometimes are confusing. Thanks!
Question - is it possible to set up the VFD Controller XSY-AT1 so that when turned on it works at high speed, about 2-3 minutes, but after 2-3 minutes of operation to a pre-set low speed? A pool water pump is connected to the XSY-AT1 frequency converter.
Didn't you receive the user manual with all the parameters along with the controller? If you are looking for detailed information, I recommend visiting the channel www.youtube.com/@ZygmuntKiliszewski and asking questions there. You will certainly receive more information. He has a lot of knowledge on this subject.
? My wiring is correct. Two 110v hot wires input. No neutral. The inverter spins up to 60hz. The motor does nothing. The table saw has separate Allen Bradley start and stop switches. They are not wired into the remote start/run terminals in the inverter. I thought using the Run button on the inverter would supply current to the motor. I'm getting 130v on all 3 terminals in the Allen Bradley junction box on the saw. Any advice?
Pytanie czy istnieje możliwość zaprogramowanie tego przetwornika częstotliwości tak aby silnik krecił się ok 30 obr na min? Jeśli tak to jak to zrobić?
Yes, it does. It significantly reduces the electric field generated by the cable. When grounding is connected to a shielded cable, there is no electric field.
@@pureexpanse Yes, but the frequency converter itself generates the same magnetic field and would also have to be shielded. (I read somewhere) or only the cable? Thanks
@@InfBerBat143 It is best to have an electromagnetic radiation detector and then you will be able to see the differences after connecting the shielded cable with and without grounding and how much is on the inverter itself
Ciao...siccome ho anch'io un ATI 1 2.2KW installato su un motore trifase 750w per il mio tornio ... ed ho un problema che quando gira il motore mi genera una anomalia tra massa e neutro di circa 20/24v non è normale e mi fa interferenza nel display lcd 16x2 del contagiri comandato da arduino...ho visto nel tuo video che hai messo al motore un cavo a 4 poli SCHERMATO come mai? Grazie in anticipo.
Ehi.si l'ho dato schermato perchè ogni inverter emette interferenze che si possono eliminare collegandosi come nel video.se fai come ho fatto io i problemi dovrebbero scomparire.saluti.
@@pureexpanse grazie della risposta...e che tipo di cavo hai usato? che sinceramente non ho mai visto...mi puoi mandare il link di dove posso acquistarlo? Grazie molto gentile.
@@Roberto-cc4el Ho un cavo di scarto. A volte puoi trovare cavi davvero buoni nella discarica, ma puoi comprarli. E' importante che sia abbinato al cupolino e al diametro del motore, viene sempre descritto per quale potenza è consigliato.
Hi can you please help i have a cross cut saw and need to put in a two way switch so that i can have it running continuously or on the hand button stop&start also i need to put in an emergency stop
Hello, I have a lathe with a 3kw / 380v motor, I can put a 4kw Toshiba converter on it. I mention that at home I have 220v and I connect it to a converter with 220 input and 3 phase output
o kurcze dobry patent 🎉
😉
The XSY-AT1 you are working is a model from 2023?. I found one on amazon but its a white, maybe is from an older version. Asking so i can know wich one i should get. Thank you. Btw, what is the exact name and model the tools you are using on the 1:15 minute and also the 1:49. I wanna get those from amazon right away.
I don't know what year this model is from. One is an insulation squeegee and the other is a connector crimper.
@@pureexpanseThanks. I just ordered the same vfd from amazon yesterday, also ordered the crimper. I asked the name because I'm from south America, and the translation of the tools sometimes are confusing. Thanks!
@@MavG 😉
Question - is it possible to set up the VFD Controller XSY-AT1 so that when turned on it works at high speed, about 2-3 minutes, but after 2-3 minutes of operation to a pre-set low speed? A pool water pump is connected to the XSY-AT1 frequency converter.
Didn't you receive the user manual with all the parameters along with the controller? If you are looking for detailed information, I recommend visiting the channel www.youtube.com/@ZygmuntKiliszewski and asking questions there. You will certainly receive more information. He has a lot of knowledge on this subject.
? My wiring is correct. Two 110v hot wires input. No neutral. The inverter spins up to 60hz. The motor does nothing. The table saw has separate Allen Bradley start and stop switches. They are not wired into the remote start/run terminals in the inverter. I thought using the Run button on the inverter would supply current to the motor. I'm getting 130v on all 3 terminals in the Allen Bradley junction box on the saw. Any advice?
Please go to Zygmunt Kliszewski's channel and ask him questions. He has extensive knowledge on this subject. I think he will help you.
www.youtube.com/@ZygmuntKiliszewski
Thanks @@pureexpanse
@@PatHudgins 😉
Pytanie czy istnieje możliwość zaprogramowanie tego przetwornika częstotliwości tak aby silnik krecił się ok 30 obr na min? Jeśli tak to jak to zrobić?
Proponuję abyś odwiedził kanał Pana Zygmunta Kliszewskiego.Ma bardzo dużą wiedzę na ten temat.Na pewno odpowie na Twoje pytania.
Does the shielded cable do anything? the frequency converter also needs to be shielded, right?
Yes, it does. It significantly reduces the electric field generated by the cable. When grounding is connected to a shielded cable, there is no electric field.
@@pureexpanse Yes, but the frequency converter itself generates the same magnetic field and would also have to be shielded. (I read somewhere) or only the cable? Thanks
@@InfBerBat143 It is best to have an electromagnetic radiation detector and then you will be able to see the differences after connecting the shielded cable with and without grounding and how much is on the inverter itself
Ciao...siccome ho anch'io un ATI 1 2.2KW installato su un motore trifase 750w per il mio tornio ... ed ho un problema che quando gira il motore mi genera una anomalia tra massa e neutro di circa 20/24v non è normale e mi fa interferenza nel display lcd 16x2 del contagiri comandato da arduino...ho visto nel tuo video che hai messo al motore un cavo a 4 poli SCHERMATO come mai?
Grazie in anticipo.
Ehi.si l'ho dato schermato perchè ogni inverter emette interferenze che si possono eliminare collegandosi come nel video.se fai come ho fatto io i problemi dovrebbero scomparire.saluti.
@@pureexpanse grazie della risposta...e che tipo di cavo hai usato? che sinceramente non ho mai visto...mi puoi mandare il link di dove posso acquistarlo? Grazie molto gentile.
@@Roberto-cc4el Ho un cavo di scarto. A volte puoi trovare cavi davvero buoni nella discarica, ma puoi comprarli. E' importante che sia abbinato al cupolino e al diametro del motore, viene sempre descritto per quale potenza è consigliato.
Witam. Można konkretny namiar na produkt . Szukam na ale... Ale dużo podobnych jest . Dziękuję i pozdrawiam 👊
Niestyty nie podam ci bo nie ja zamawiałem lecz znajomy a zamawiał na al..
Hi can you please help i have a cross cut saw and need to put in a two way switch so that i can have it running continuously or on the hand button stop&start also i need to put in an emergency stop
I'm not that versed in electrical stuff. You would have to find a forum or channel dealing with these things.
Can this connection be use for higher speed motor that turning electric alternator motor
It's best to read the full specifications of the device.
Four panels go 560 watts and the second thing is which GFT will be applied to the three piece motor
👍👍ten falownik ma funkcję hamowania silnikiem? tak to przynajmniej wyglądało jak zmieniałeś obroty
Tak ma na jednym ujęciu masz cały opis ustawień jest tego sporo.
@@pureexpanse To spoko bo chyba nie drogi tylko ja będę chciał na 3f
@@pawekowalski7469 Chyba jeden z najtańszych. Na 3 fazy jest z tego co pamiętam AT3
Hello, I have a lathe with a 3kw / 380v motor, I can put a 4kw Toshiba converter on it. I mention that at home I have 220v and I connect it to a converter with 220 input and 3 phase output
You will receive all information by asking a question on the Zygmunt Kliszewski channel.
Prosze o pomoc
Witam czy ten falownik wektorowy jest i jaka firma
Mode jest w opisie XSY-AT1 VFD jaka firma nie wiem pewnie jakiś chińczyk bo tani był.Najlepiej wpisać model i poszukać dokładnej specyfikacji.
@@pureexpanse dziękuję
@@krzysztofgros4245 Proszę
Jak z Panem można sie kontaktowac
A o co chodzi?
Cos naklikałem w ustawieniach i znikły mi obroty mam nastawione 2800 w falowniku a moge tylko 1069 prosze obejżyj film
Nawed po zresetowaniu falownika do fabrycznych ustawien nic nie momaga
Ktos mi napisał zebym sprawdził parametr p25 ale w instrukcji nic tam nie ma otym jak wchodze sa same zera
Jestem w stanie odplatnie za sparcie
Son un hueso tengo días intentando quitar el bloqueo de cambió la clave en p09 y se olvidó ahora no deja cambiar ningún parmetro
W sprawie falownika