Installing a Rectangle to Round Transition into an Existing Metal Duct

Поділитися
Вставка
  • Опубліковано 13 гру 2024

КОМЕНТАРІ • 27

  • @Mabalzitch2024
    @Mabalzitch2024 4 роки тому +9

    That drive cutting trick is great! Thank you for sharing.

  • @resurgensix
    @resurgensix 3 роки тому

    Eduardo in Charge Yo! Binging all your work.
    Deep diving sheet metal vids thanks to you.

  • @hangngoaigiare
    @hangngoaigiare 4 роки тому +1

    please make vids about the whole house duct plan out and installation

  • @hozerhvac4406
    @hozerhvac4406 4 роки тому +5

    You need to keep this guy going with videos. Is he a Kalos employee ?

  • @ThePachucoMix
    @ThePachucoMix 2 роки тому

    Thank you very much for share your knowledge hope you keep making sheet metal videos 👍

  • @JimGrady67
    @JimGrady67 4 роки тому +1

    Good video!

  • @Sirvivu
    @Sirvivu 4 роки тому +1

    cut the hole, turn out 25 mm on the the square to round duct then used pop rivet gun or weld,

  • @briangraham7363
    @briangraham7363 4 роки тому +1

    Thank u

  • @willmek
    @willmek 4 роки тому +1

    why would you use a square to round instead of a takeoff?

    • @Sirvivu
      @Sirvivu 4 роки тому

      That way for the take time guys mate. For me, cut the hole, then turn out 25mm at square to round duct, silicon on that. Done on 5 minutes

    • @willmek
      @willmek 4 роки тому +2

      @@Sirvivu 5 minutes? Sounds like you’re a take time guy yourself. You must be a plumber.

    • @Sirvivu
      @Sirvivu 4 роки тому

      @@willmek nah, just kidding guys, in Australia we not use that joint.

  • @FLAWLESKILLER
    @FLAWLESKILLER 2 роки тому

    The Sq to round piece should of been large ended to slide over the existing vertical duct, cut out inside measurement of the Sq to round piece, and screw the sq to round to existing duct

  • @tealkerberus748
    @tealkerberus748 9 місяців тому

    All this when you didn't even actually want a 90 degree bend? Why not use a piece to give a Y branch?

  • @anthonygonzalez7488
    @anthonygonzalez7488 4 роки тому

    5:55 / Malco actually makes tools ( s2rls ) that make this part of the construction professional looking rather than using a tool meant for plumbing work,,,

    • @joshuaricks7730
      @joshuaricks7730 4 роки тому +2

      He said he left his duckbill pliers.

    • @paulgaras2606
      @paulgaras2606 4 роки тому +2

      Channellox are what service guys use.💪🏻

    • @hvacir9176
      @hvacir9176 4 роки тому +3

      he said that he left it somewhere and u still commented.

    • @gonzaloalcantar6522
      @gonzaloalcantar6522 4 роки тому +1

      Pay attention! He said he forgot them somewhere 😑

    • @anthonygonzalez7488
      @anthonygonzalez7488 4 роки тому +3

      Quite a few new students coming into the trade need to be shown how to do a job correctly. In the video it was shown that a tool, not designed for the job at hand, could be substituted. Those schooled it the trades know otherwise . Hand this been a joe handy man channel the premise would be understandable.

  • @KentuckyReef
    @KentuckyReef 4 роки тому +1

    Tongs

  • @baba-sm1fm
    @baba-sm1fm Рік тому

    Ma sei Italiano?