How to Replace Camshaft on M276 Engine
Вставка
- Опубліковано 16 вер 2022
- Hello and welcome to my UA-cam channel! In this videos, I want to share with you how to replace camshaft adjuster on M276 Engine.
M276 Camshaft Adjuster kit: amzn.to/3rn8U0O
M278 Camshaft Adjuster Kit: amzn.to/3pOeCsa
Mercedes Benz M157/M276/ M278,
Camshaft Timing Alignment Tools Set: amzn.to/3K4CONT
More Mercedes-Benz videos: mohecta.com
If you like the uploaded videos, please subscribe, like, share and comment for more future videos. Thanks for watching! - Авто та транспорт
Great video!! Thank you so much for taking the time and understandably recording them.
Can I kindly ask you to share the torque specs for this job:
1. bolts that hold the 2 camshafts downs
2. Timing chain tensioner
3. Valve covers/ cam covers,
4. PCV valve
5. High-pressure fuel pump
6. Injector rail
7. Front cam adjuster cover
8. Lower and upper intake manifold
Thank you in advance!!
Very nice. Can you show me how to check which of the four wheels is making noise? How did you know that it was in the right block and on the intake side?
I like this style of video! Worked for MBZ as an apprentice and then moved to VW on the line. Need to do my cam sprocket I believe, due to P002177 (intake camshaft bank 1 implausible signal) for my C400 w/M276 DE 30 LA, no OEM scan tools so tough to confirm with live data, thinking of just ordering parts, removing cam covers (leaking anyways, as they do) and seeing if my cam measures okay, and if the sprocket has failed. Do you have any advice, and also, should I replace chain/tensioner while I'm in there due to slight rattle, or is reusing the chain okay as long as my tensioner isn't fully extended as per the standard? Thanks in advance & keep up the content!
Great video it’s obvious you are great mechanic. Hope you share more. I have same engine. I found oil in one one the spark plugs, so I assume I need to do valve cover gasket. What is reasonable to pay for that job?
Thanks for this video! Would you please explain the requirement & procedure for setting the timing? Also, for fault code P0021 & P054C, which parts need to be replaced please? This is for a 2019 M276.823 bi-turbo 3.0L with less than 11K miles.
Great.
Very good job! may I ask you what's the Torque Specs on the Timing Camshaft Sprocket?
This could have been a fantastic video, had you explained how you set the timing on the new camshaft and the new adjuster. You tried to do that by pointing your finger to a few things, but I have no idea what you were pointing to, or what your criteria were. Perhaps you could edit this video by adding sound to it explaining the timing. Thanks for the effort anyway.
Great suggestion!
If you were talking a little bit to explain it would be awesome.but very great video.do you know the torque required for the torx 100 adjuster bolt? Thanks for sharing
Very good job!!! I love your videos..... What are the torque specs for the valve cover?
10 Nm and 90 degree
Where is the crankshaft position sensor located at on this engine?
Very good job!!! What tools did you used??
Mb hold down tool.
Great video, I would appreciate a little more insight on how to set the camera shaft.
I'll make video for that in the near future.
Thanks
Can clarify the question I don’t understand?
@mercedestipstricks7869 Sorry , I ment cam shaft.
Anyone know torque spec for camshaft holder at 8:25 I’ve been googling forever and can’t find info.
I have the same engine on 2012 ML350. Recently the breather valve was replaced as I was getting P2279 code. Along with it, the intake manifold gaskets was also replaced by the independent mechanic nearby. I think there was 6 baskets replaced. I went to the dealer this week for a service special free diagnostics and he is saying there is a small leak in the left and right cylinder gaskets (not sure if they are called camshafts cylinder?). The rubber seal and ring costs merely $15 but the total cost including labor is a whopping $1300. Is this worth? I touched the oil and it’s barely there. There is no check engine light what so ever. After spending close to $800 just last month I need spend money again? Can you please suggest what you think?
He’s talking cylinder head gaskets leaking. It is very rare that head gaskets are leaking on this engine. Usually, cam plugs and the oil separator on the of the engine are leaking and if they leak bad it would dripping on the exhaust and you would smell oil burning.
@@MercedesBenzTipsTricksM276 still has rear camplugs like M272 used to, really??
Great video. 👍But always remember to disconnect the battery before disconnecting any electrical components. Mainly the brain box.
Thanks!
What Symptom(s) did you have that Will Call For this Replacement???
I think few seconds rattle noise when cold start. I have such a noise and Mercedes service diagnose is change the engine😢. But now I’m looking for mechanic who can do such a work like on this video
I would like to see the oil pressure VVT valves being cleaned and/or being replaced. I have a bank 2 problem where it states cam sensors and actuators and misfires in both intake and exhaust. This 2016 E350 is throwing a multitude of codes!
Have you checked for the oil intrusion on wiring harness from the ME control unit to the components. This is very common on this year model.
I’ve had the oil leak he mentions, make sure land check ECM connector for oil when this happens, and check fuse number 24 fuse under the hood If you are getting multiple misfire/actuator codes on 4,5,6.
Does cam covers need to come off if I only need to replace intake cam adjuster on bank 2?
Yes
@@MercedesBenzTipsTricks I saw
People do the job from the timing cover only
@@MiloTheMiniDachI think he changed crankshaft and crankshaft adjuster so in this case you will have to remove intake but I saw some other video they only change crankshaft adjuster and they did it with our removing the intake. It’s possible but you really need to know what you are doing and pre mark the position before removing old one and putting the new one back. I went to dealer for same job and they quoted me $6800 which I think too high. My car drives and runs fine but from past week I hear rattle at startup early in the morning
I have a 2012 mercedes-benz e350 with the code p0018 can you help me any advice will be appreciated thank you
Did u end up fixing it
Where is the part of the actual instal?
Greets
I found some oil in the engine air filter box, there was more oil in the air intake duct before the throttle body. Could that be due to failing PCV?
No. PCV on Mercedes. It's crankcase system faulty.
@@MercedesBenzTipsTricks so whats the fix there or what if I don’t do anything?
Vacuum Pump removal?
Hallo
I have same engine on my CLS 2012 , when I start it cold or hot some blue smoke come out , and engine have more than normal vacuum. In 2000 km need like half Liter oil .
I was by Mercedes then didn’t found the problem.
Can you please tell me what is the problem.
Thanks
Thanks for reaching out. There are two comment things on blue smoke coming out from tail pipes in your case. You have leaking piston rings or worn valve stem seals or both regardless of vacuum pressure. These are bad that's why the engine consuming lots of oil.
Did you disconnect the battery before disconnecting the ECU?
I did
Would like to have seen the Camshaft adjuster installed and torqued. Kinda critical, me thinks. A lot of good info, but several key pieces omitted from view, especially for a "How to" video.
😮
Removing that PCM bracket would surely help, but looks like a pain to perform.
I would call it rather how to put silicon on the valve cover gasket instead of how to replace camshafts))).. its ok dough.