@@seikojason meinst du vom hersteller? Oder er hat es vorher entfernt um den effekt zu zeigen🤷(wenn da ne nut ist gehört da eigentlich ein lager rein,sonst würde das anders(ohne nut)gespritzt werden)..
I hope you think you are very smart now but I have the same one, took it apart and there is only one bearing in it. He just added an extra one in the other slot that is empty by factory. Making dumb comments out of ignorance is also priceless. :D
@@hunjoey Maybe. But we have so many videos on youtube with such stupid repairs. It was so strange to me that the manufacturer did not put an additional bearing when there is a prepared place for it. It looks like an attempt to make a video out of nothing.
@@vovashka2245totally agree with u) if we imagine, that he get instrument with only one bearing and add second - why he use "magic trick" with lent? It's illogical, if we assume the fair repair. But it"s easy to explain, if we assume the fake repair.
@@matb748this is wrong. I have this one twice and it doesnt vibrate at all. The chuck itself is most likely to fail due to being made of cheap aluminium.
Well fuck me, either it only comes with one or there's a factory fudge up. Mine only had one bearing, Cheers bud, now my hands don't tingle after every time I have to use this tool 😂😂😂
Aaah the wonderful sound of a unbalanced tool mounted, which is primarily what wears out the bearing very quick, I’ve found that mine is very quiet and nice if you take a little care trying to reposition the tool just a little in order to balance it before using. Making sure the tool is very balanced is super important especially when using heavier or big size ones like the grinding discs etc, also pressing very hard with the tool against something while unbalanced eats up bearings even faster still. Good luck everyone, and remember to balance your spinnymathingy! 😉
@@RobertPucovsky I usually balance my tools instead, it’s a process of checking for vibration before using it on stuff, and if there’s “too much” simply loosen it a little and turn the tool just a smidge, tighten and check again - then repeat until it’s decently stable. Depending on if the tool is sharp or not, if the latter I also check with my finger against the tool to feel for vibrations, once you have gotten it right you will immediately know if it’s balanced or not even if it’s a small and thin tool, but never do that with any tool that can hurt your fingers! Also remember that using a chuck makes it more likely to be unbalanced compared to using the collets that comes with. And if you use a tool that’s not balanced it will be worn unevenly, making it harder in the future to use and balance too. Good luck!
Não sei se está certo mas usar fita pra tirar folga mas se sim, essa tecnologia top😅 Geralmente troca o eixo ou faz preenchimento de solda Mas para elucidar foi legal
Tenía una y solo tenía un rodamiento,es para desgastar el buje del del motor, obsolescencia programada,x lo demás muy buen aparato,😢una pena se mw daño el motor,comprare otra y le hago esta adaptacion😊
Jak widzę takie naprawy to chce mi się płakać że śmiechu 😂 skoro łożysko wybiło stalowy wałek to jakie szansę ma miękka taśma teflonowa 😅 lepiej wykonać tulejke chociażby z stalowej blaszki po puszce 😉
@@Alex-uh1mjas of a mechanical engineering standpoint of view, you never use more than two bearings on one axle. Nothing is manufactured perfectly and two bearings have enough wiggle room to handle this. If you put a third bearing on the axel there is no wiggle room anymore. You force it in place. The weakest point will now wear out quickly. Now the weakest point is the bronze bearing of the motor... So this modification isn't really good, it will wear out the motor bearings. With a bit of luck this will not make problems, because the axle has two bearings and will "hold" the motor axle in place. But it will most likely get noisier and noisier over time. The motor axle can even break if it's wiggling too much. PTFE is also too soft, as it was used here. The bearings will lose again. Loctite bearing glue would be better. The best modification here would be glueing in one single bearing in the upper place and securing the motor if it is wiggling around. If the rotation is then eccentric/wobbly the axle is not straight. Forcing it in place with an additional bearing will cause the mentioned problems above. The goal then is to straighten it up somehow.
@@matthiash.4670 mate. What are you on about. There was only one bearing in there. I said it was strange there is space in the molding for 2 and its stange there wasnt 2. Im an engineer i design vehicles
Hi I recently watched your video on tools for working with computers and other electronics, and I found it very informative. I am currently in the market for an electric screwdriver pen that meets the following criteria beter for es666 screwdriver: Has a USB-C charger Uses a Li-ion battery Is slim and long enough to reach deep screws in computers and other materials Could you please recommend a brand or model that you trust and have had a good experience with? Thank you in advance for your help!
Nel primo video manca un cuscinetto, inoltre la prova iniziale la smerigliatrice girava più lentamente aumentando le vibrazioni è l’effetto di squilibrio nella punta e solo un falso😮
I have this exact tool here in Australia got it from Bunnings Burnie I seen this video and disassembled and sure enough the comments are real it's a view revenue scam because mine has the top and bottom bearing installed.. it's obvious that the Dremel needs it or it will chew up the bottom bearing from excess wobbling from not enough support of the shaft!!! It really does have the 2 bearings from the factory.. either you got a tool assembled by an idiot and the company has no QC inspector or your video is garbage lies!! Oh and so you know I've had cheap Dremels and expensive one's and the driver shaft on all including the cheap Chinese shit has 2 top bearings to stop wobbling and so it doesn't vibrate itself to death after 5 minutes of grinding or cutting.
Me wondering why they didn't include a second bearing in the first place... Also how much did you pay for that electric screwdriver? I got one for 10 bucks but it's not anything to write home about.
Ну как минимум изначально одного подшипника не хватало, а вот садить подшипник на фум ленту - мой профессор по стандартизации перевернулся в гробу😂😢...
Wo ist denn das vordere Lager geblieben. da war doch ursprünglich auch eins drinn. Der Wellendurchmesser ist auch unterhalb der Lagertolleranz, dann mit Teflonband die fehlenden 0,05 mm ausgeglichen, was für ein Müll. Da ist doch 3 Jahre Garantie auf dem Gerät.😂😂😂
Контент мейкер без головы, думаешь мы не заметим отсутствие второго подшипника? Подшипник второй перед съёмками: "ну да нуда пошел я нахер, чтобы меня сначала сняли перед сьемками а потом поставили на посадочное место"
Гениально! Подшипник на валу болтается , а уплотняет фумом с наружи. Да это же ШЕДЕВР!
Без синей изоленты на день хватит🤣🤣🤣👍
То есть то что люфта он демонстрировал с 1 подшипником а собирал с двумя это ты не заметил? То есть фумка там чисто для понта
На 15 минут работы
Я таку проблему убирал меднением
Там в конце ещё волшебный второй подшипник появился которого изначально по ооочень непонятным причинам не было
Warum fehlt am anfang das vordere kugellager?😅
Material gespart
@@seikojason meinst du vom hersteller?
Oder er hat es vorher entfernt um den effekt zu zeigen🤷(wenn da ne nut ist gehört da eigentlich ein lager rein,sonst würde das anders(ohne nut)gespritzt werden)..
@@Rantanplan-0815 vom Hersteller. Ich habe das gleiche Gerät.
Parkside🤷
@@Rantanplan-0815 Parkside stellt diese Geräte so her. Ich habe selber zwei Stück.
Removing 1 bearing takes 5 minutes, deceiving everyone is priceless.
I hope you think you are very smart now but I have the same one, took it apart and there is only one bearing in it. He just added an extra one in the other slot that is empty by factory. Making dumb comments out of ignorance is also priceless. :D
@@hunjoey Maybe. But we have so many videos on youtube with such stupid repairs. It was so strange to me that the manufacturer did not put an additional bearing when there is a prepared place for it. It looks like an attempt to make a video out of nothing.
@@vovashka2245 I have this exact tool and they are made only with one bearing. For cost cutting reasons i suspect.
@@vovashka2245It literally has a space for the bearing, I assume the other comments is just the OP with an alt account
@@vovashka2245totally agree with u) if we imagine, that he get instrument with only one bearing and add second - why he use "magic trick" with lent? It's illogical, if we assume the fair repair. But it"s easy to explain, if we assume the fake repair.
Nah you removed 1 bearing to make it look like a defect
Sorry but no it is from factory with one Bearing I also improved my grinder with a second bearing and it works for the third year as new
@@matb748this is wrong. I have this one twice and it doesnt vibrate at all. The chuck itself is most likely to fail due to being made of cheap aluminium.
Yes😂😂😂😂
It does appear there is a slot for a second bearing that was missing.
Well fuck me, either it only comes with one or there's a factory fudge up. Mine only had one bearing,
Cheers bud, now my hands don't tingle after every time I have to use this tool 😂😂😂
Разобрал, в корпусе место под второй подшипник. Вопрос: или уже проипал второй, или это экономия на фабрике.
я свою точ таку машинку розбирав там не було 2-го подшипника
@@МарянЛазурка-м1о у него даже след на валу от второго подшипника
Или всё сделано намеренно, чтобы показать МОЩНЫЙ ЛЮФТ😂
Автор скорее всего сам снял чтобы был люфт
Судя по комментам там с завода 1
Aaah the wonderful sound of a unbalanced tool mounted, which is primarily what wears out the bearing very quick, I’ve found that mine is very quiet and nice if you take a little care trying to reposition the tool just a little in order to balance it before using.
Making sure the tool is very balanced is super important especially when using heavier or big size ones like the grinding discs etc, also pressing very hard with the tool against something while unbalanced eats up bearings even faster still.
Good luck everyone, and remember to balance your spinnymathingy! 😉
I have the same Parkside dremle, how do you balance it? Like go full out on a lathe?
@@RobertPucovsky I usually balance my tools instead, it’s a process of checking for vibration before using it on stuff, and if there’s “too much” simply loosen it a little and turn the tool just a smidge, tighten and check again - then repeat until it’s decently stable.
Depending on if the tool is sharp or not, if the latter I also check with my finger against the tool to feel for vibrations, once you have gotten it right you will immediately know if it’s balanced or not even if it’s a small and thin tool, but never do that with any tool that can hurt your fingers!
Also remember that using a chuck makes it more likely to be unbalanced compared to using the collets that comes with. And if you use a tool that’s not balanced it will be worn unevenly, making it harder in the future to use and balance too.
Good luck!
where the first bearing beafore you replace it ?
So satisfying to watch 😊
Ахренительная надёжность- фум лента, это круче чем синяя изолента
Фумка?😂 Серьйозно ? Даже не алюминий из банки ? 😂 Шедевр .
Nice, that's a satisfying repair❤
Parabéns pelo trabalho de qualidadeee!!
Que Deus nos abençoe sempreeee 😊
При разборке верхнего подшипника вала уже не было 😂😂 автор гений
Não sei se está certo mas usar fita pra tirar folga mas se sim, essa tecnologia top😅
Geralmente troca o eixo ou faz preenchimento de solda
Mas para elucidar foi legal
Фум лента это вещь а ещё он классную отвёртку показал И вопрос а заяем на новый инструмент старая обжимная гайка?
А чо ей будет?
Powinni dodawać taką taśmę do każdego urządzenia i serię nazywać " zreperuj to sam"!😂
Love your screwdriver. What model is it?😊
Das Video gefällt mir 😊 man kann was sehn und lernen
Well done, I am satisfied with you
Tenía una y solo tenía un rodamiento,es para desgastar el buje del del motor, obsolescencia programada,x lo demás muy buen aparato,😢una pena se mw daño el motor,comprare otra y le hago esta adaptacion😊
Hold up that screw driver is cool asf, were u get that
If he would have not added the second bearing, nobody would have noticed it 😅
Mais uma excelente ideia. Muito obrigado
Jak widzę takie naprawy to chce mi się płakać że śmiechu 😂 skoro łożysko wybiło stalowy wałek to jakie szansę ma miękka taśma teflonowa 😅 lepiej wykonać tulejke chociażby z stalowej blaszki po puszce 😉
I cut a beer/coke can (~0.03mm) or a spray can(~0.06mm) for thin metal stripes (alu or steel) One can coil it to the shank as much as needed.
Please can you tell us the number of the ball bearing? Thanks
687Z (7 x 14 x 5)
Thank you very much. Aggelos from Thessaloniki Greece
So strange there is space for 2 but they didnt use 2
@@Alex-uh1mjas of a mechanical engineering standpoint of view, you never use more than two bearings on one axle. Nothing is manufactured perfectly and two bearings have enough wiggle room to handle this. If you put a third bearing on the axel there is no wiggle room anymore. You force it in place. The weakest point will now wear out quickly. Now the weakest point is the bronze bearing of the motor...
So this modification isn't really good, it will wear out the motor bearings. With a bit of luck this will not make problems, because the axle has two bearings and will "hold" the motor axle in place. But it will most likely get noisier and noisier over time. The motor axle can even break if it's wiggling too much.
PTFE is also too soft, as it was used here. The bearings will lose again. Loctite bearing glue would be better. The best modification here would be glueing in one single bearing in the upper place and securing the motor if it is wiggling around. If the rotation is then eccentric/wobbly the axle is not straight. Forcing it in place with an additional bearing will cause the mentioned problems above. The goal then is to straighten it up somehow.
@@matthiash.4670 mate. What are you on about. There was only one bearing in there. I said it was strange there is space in the molding for 2 and its stange there wasnt 2. Im an engineer i design vehicles
😊Thank you for the method of repairing this tool.👍🏻👍🏻👍🏻
I have had the same problem with my el-cheap-o rotary tool... I will have to re-measure my arbor so that I can order a better fitting bearing.
Es el Lidl 😂😂😂
Yo también tengo una.
Hi
I recently watched your video on tools for working with computers and other electronics, and I found it very informative. I am currently in the market for an electric screwdriver pen that meets the following criteria beter for es666 screwdriver:
Has a USB-C charger
Uses a Li-ion battery
Is slim and long enough to reach deep screws in computers and other materials
Could you please recommend a brand or model that you trust and have had a good experience with?
Thank you in advance for your help!
Nicely done
DANKE SCHÖN MUSS HEUTE ZAHNARZT UND MUSS BOREN
Почему был 1 подшипник изначально ?
Для контента снял
@@Сергей-о3л2ж неа не для контента там реально не було я свою розбирав така сама фигня
Deswegen kaufe ich gleich etwas, was dann verlässlich ist. Auch wenn der fix gut gemacht ist😊
Nel primo video manca un cuscinetto, inoltre la prova iniziale la smerigliatrice girava più lentamente aumentando le vibrazioni è l’effetto di squilibrio nella punta e solo un falso😮
Why is there only 1 ball bearing in why did you take out the 1st one
Dat vibration occurs because u remove top bearing for the video..😂😂😂😂
Anyone who has this one knows that they are with single ball bearing.
@@ErCanEverything Then why was there a built in slot for a second bearing
Its from factory with one Bearing... don t judge IF you didn t know
Not if they havent took it a part they dont as most people wouldn't,why would they.
Bit of a ludicrous statement to say the least.
I have this exact tool here in Australia got it from Bunnings Burnie I seen this video and disassembled and sure enough the comments are real it's a view revenue scam because mine has the top and bottom bearing installed.. it's obvious that the Dremel needs it or it will chew up the bottom bearing from excess wobbling from not enough support of the shaft!!! It really does have the 2 bearings from the factory.. either you got a tool assembled by an idiot and the company has no QC inspector or your video is garbage lies!!
Oh and so you know I've had cheap Dremels and expensive one's and the driver shaft on all including the cheap Chinese shit has 2 top bearings to stop wobbling and so it doesn't vibrate itself to death after 5 minutes of grinding or cutting.
На туалетной бумаге лучше бы работал
Le habéis puesto 2 rulemanes en lugar de 1 que tenía originalmente. Pero ¿era necesaria la cinta adhesiva?
I had to put a tape because there is a lot of clearance between the bearing and the shaft.
La levigatrice performance ha lo stesso difetto, sai se è risolvibile?
Open it and see if it has a 2.nd bearing slot, I think it will work.
Lo voy a hacer ya 😮😮
When you break an arm or leg, let the doctor fix it with tape...😅
Me wondering why they didn't include a second bearing in the first place...
Also how much did you pay for that electric screwdriver? I got one for 10 bucks but it's not anything to write home about.
I bought it 2-3 years ago for €22
Are we going to ignore that one bearing was missing?
Сначала снять второй подшипник а потом якобы усилил. Гениальное налюбилово
Контентище же надо пились))
Купи и убедись, там всего один подшипник!
Друг, покажи что у тебя за отвёртка такая, пожалуйста 🤝
Мягкое нельзя 😂 вы где такие профи беретесь😢😂😂😂
Thanks 👍🙏🌹❤
First was only 1 bearing. Sneaky little cheat. 🤔
I have this exact tool and they are made only with one bearing. For cost cutting reasons i suspect.
Ну как минимум изначально одного подшипника не хватало, а вот садить подшипник на фум ленту - мой профессор по стандартизации перевернулся в гробу😂😢...
Sólo era que pusieras de nuevo el rodamiento que quitaste 😂
So satisfying
I think I have to do this to mine now.
Where is the top bearing that’s supposed to be there. Did you lose it or remove it for the sake of the video?
Where did you get those bearings from, I am looking for them
aliexpress
На сколько времени хватит этой фумки при работе?
В магазине полно новых и не только подшипников !😊👍⚙️
Nice fix
Hay soldadura fría de aluminio se utiliza para botes de pesca pequeños eso sirve para este uso
بد نبود دمت گرم
You can just use bearing glue instead of tape
Welcher mini schrauber ist das?
Jak długo podziała?😂
this grinder is very poor, it slows down with a little pressure, any way how to hack its torque limiter?
1 bearing? Why?
🤷 Parkside
You added second bearing?
Yes
@@ErCanEverything It looks like it should be there in the first place.
Оригинальный подшипник не заказать?
Nice 🥰
where did you get those bearings?
where did you get your phone?? 😮
hi, could you please give me the measurements of the bearing, I have the same model and I would like to make this change
Before Bering there was only 1😂😂
So the tape does the trick?
Its teflon don't buy that unless you like toxic
а никого не смущает что при разборке изначально там стоял один подшипник?
That's exactly what I'm showing you, the place is planned but there was no bearing🤷
Гениально вытащил 2 подшипник создав иллюзию что он там не был и поставил новый и все заработало как надо 😂😂😂
Удивись, там нет второго подшипника!
У меня точно такой же агрегат.
хотел ехать с стоматологу, как только услышал звук, сразу перехотел
Феерично, место под второй подшипник есть, а подшипника нет. Экономия должна быть экономной, прааильной дорогой идёте камрады.
Теперь вал будет разбит раньше и, намного сильнее. После фум лентового ремонта вал можно выкидывать.
Wo ist denn das vordere Lager geblieben. da war doch ursprünglich auch eins drinn.
Der Wellendurchmesser ist auch unterhalb der Lagertolleranz, dann mit Teflonband die fehlenden 0,05 mm ausgeglichen, was für ein Müll. Da ist doch 3 Jahre Garantie auf dem Gerät.😂😂😂
А где второй подшипник в начале разборки?
Там всего один !
Cette mini meuleuse est super jen ai une et la batterie tiens pas trop mal
Сколько может стоить такая электро отвёртка, подскажите.?
фикс на 10 минут)
Bro, it's has only one bearing from the factory, just please listen to him
What bearing type is in there?
You didn't need to change the bearings, just put the bearings on the top of the K. 😂😂
Ou acheter les roulements ?
Would have been easier to just throw it in the trash and buy a Dremel tool..
🤦🙂
Чёт я нихрена не понял, в итоге сколько там подшипников, 1 или 2?
Контент мейкер без головы, думаешь мы не заметим отсутствие второго подшипника?
Подшипник второй перед съёмками: "ну да нуда пошел я нахер, чтобы меня сначала сняли перед сьемками а потом поставили на посадочное место"
But why it had only 1 before?
Už vidím, jak to hoří, kvůli malé vůli. 🤣
Don't use tape. Take tin from soda can.
which moter is this??
Soy mecánico ajustador, tornero fresador, ver esto me da fatiga. Qué pena.
They didn't put the slots for the snaprings on the to bearing
Liar liar pants on fire 🔥🔥
Well, you only put 1 ball bearing, it must put 2 pieces.
И что, под нагрузкой фумка не продавится?!
What name about that tool.
Не дай бог чтоб такой мастер ремонтировал инструмент
i have the same problem too the bits sway