As always I think your videos are outstanding! I've been subscribed to you for a couple years now. But for the second time in that period I find myself mysteriously unsubscribed to you so thanks a lot UA-cam for unsubscribing me unwillfully. Keep up the great work
Duuuuude, it’s been doing it to me for channels I’ve followed for YEARS. I first noticed it when following “Street Banditos” full carbon 240Z build. I would have to keep searching and re-follow. 🖕🏻YT!!!!!!!!!
You you have been an incredible help. I bought your stuff from you guys. You’re your system you use some I suck with computer technology. I’m learning as I go much. Chevelle runs pretty good for what it is. Very nice actually Laguna Chevelle Laguna it was a big block issued 1974 or generation super sport S3 sweet car so great work keep up the good work thank you.
I got 1 of the blemished units off eBay and so far, I really like it. A few problems the boost channel doesn't show anything, it just stays at 0. And it seems you can't add custom channels to the display, which is weird because with the 3.5 I believe you can. Maybe a future firmware will fix this. I tried to update it to the SD contents on the website, but it won't let me remove what is currently on the SD card. So I have some tinkering to do yet.
@@itskamel I did figure out my problems, it was firmware. After I got it to update the boost channel works and I can add any channel I want, even the can module channels. After this however I did notice some of them will show error intermittently, only comes up for a second and goes away. Maybe a future update will fix this idk
Can you run multiple of these dashes on one ECU ? For instance could you run 2, or even 3, with a Dominator? Or one of these along with the 12" Pro Dash? I know you can run the 3.5 alongside them. I was thinking either a 12" or this 5" for the main cluster display and another 5" for an auxiliary display somewhere else in the dash - like the middle or console area that you could keep another set of parameters displayed on.
What sucks is, this will work for the Atomic 2, but tech support told me I'll lose some of the Atomic 2 functions on the display, even though they run on the same firmware. 🤷
Question: when doing 12v electric installation, I get there’s a couple different types of products to use. The one thing I’ve noticed lately is guys using more of the pre wired solenoids with the pigtails over using the all-in-one leash board or even them Amazon cheap’y fuse/relay boards or fuse boxes.
Hey Joe, Can you display custom sensor such as trans temp on the display. Good to here that you can run a 3.5 dash at the same time so log on 3.5" and still read the gauages on the 5" dash going down the track. Never worked out how to display custom sensors on the 3.5" dash Thanks for the great info on the holley products.
Joe so I wouldn’t need the 3.5 inch display to run wizard n such I can just get 5 inch? Just making sure plan on upgrading to sniper 2 this winter I had a nightmare with my sniper 1 lol. I just like thought of efi on my old car 👍
holleys ganna sell a ton of these. people are struggling to afford the stuff they want. When they release options like this that the average 50-70k worker can afford. its a big win.
yes the price is awesome. its going to be interesting to see how things go the next few years. its pretty obvious people want less expensive stuff, look how the terminator X series of ecu's absolutely exploded with popularity! a prodash with a terminator x is kind of a weird combo,the display is 2x the cost of the ecu. this unit makes far more sense for most applications i think.
Joe, is their a separate CAN connect for the pro dash or is there only one? I need to run the wizard again because i going to get new injectors, i dont want to have to undo all my work when i end up getting them so i want to leave the handheld connected as well as the pro dash. Should i be looking at getting that CAN splitter cable? Thanks
So can you run both the 5” and a 3.5”? I have my 3.5 mounted and I’ve been putting off replacing my cluster. This would be nice as a cluster replace my while using the 3.5 for extra gauges
So, the 5" dash is the ONLY dash that Holley sells that advertises that you can "Tune" with a Terminator-X system. For some reason, ALL of the larger dashes specifically say that they "Do not support tuning with Terminator-X systems." Does this 5"dash support FULL tuning? Like that it could take the place of having a laptop, and be able to tune ALL the parameters?
Does the speed get logged to the datalog? This is one channel that I really miss when tuning or rather reviewing Sniper Datalogs. I'm also interested in how well the triggered logging works. When I remember to log with the Sniper, I often forget that I have to manually stop the log before shutting the ignition off, or that log is lost. I've lost hours long datalogs that I wanted to review for long distance economy and transitional states. I assume that the triggered logging will also stop and save the log at key off?
I have a X-Max with a pro 6.86 and the speed IS logged on my log files that I hit record on the plugged-in laptop. Logging will stop when the car is shut off - I've had the car die and when I restarted the engine, obviously the holley power cycled and the log file was still saved on the laptop. Not sure about internal logging -
Question for all as I'm lost. Is terminatorX a newer version of the original Terminator? I have the Terminator Stealth system and as I sometimes do research for adjustments I notice everything is now Terminator X. Is it the same thing?
Thank you for the clarity. When you don't live or play with these systems daily and suddenly need some advice or knowledge and start researching and everything says terminator x you start wondering what you missed
@@JoeSimpsonAtTempest Can you screenshot a list of the different parameters that you can display on this unit? I'm looking to see if I need to buy aux gauges/indicators that make sense or if it can display everything I'm looking for. Need to see if I can put fuel level, turn signals, high beams, etc on this display in addition to boost pressure meth on/off, etc.
Its super easy to setup thru holley if you want to do it, get a small super bright led light, mount it wherever you find it conveniently lighting up into your face and make holley turn that on at whatever rpm you like
Man! They SHOULD have put the GPS terminal connecter down in the CANBUS connector end of the cable, so that you dont have 2 cables hanging out of the display. Fail
Was this video sponsored by Holley?...it feels like it is .... !st half was like I'm watching an add for Holley... they gave you really good talking points...for $409.95 seems a little over priced
but for the 7 inch being around double the price, it makes the 5inch the best budget option unless you wanna do a 3rd party screen like tinker electronics.
For it only being $100 dollars more than the shit 3.5” one, Holley’s cheap assh*les better start putting these in the efi kits… Especially for their wiring harness being complete shit… they can’t even route the wires in the right directions in their harnesses… Tps, and iac won’t even reach the throttle body on an ls2 with their own high ram intake lmao 😂 Next one I do, going to give FuelTech a shot, even though it’s about $650 more… if it’s a better fit and quantity, it’ll be way worth it… Well by the time you buy $170 coil harnesses that aren’t included, and 3 ICT billet extensions… not a $650 dollar difference anymore…
FuelTech's 25 year old fuel modeling should be a nice surprise for you.... there are so many better options for the price but people are just enamored by the marketing.
I wish they would add a dashboard editor to the desktop apps that you could create cool dashboards with.
Im sure they will have updates for that
Be great for all their screens. Pain in the ass
As always I think your videos are outstanding! I've been subscribed to you for a couple years now. But for the second time in that period I find myself mysteriously unsubscribed to you so thanks a lot UA-cam for unsubscribing me unwillfully. Keep up the great work
Duuuuude, it’s been doing it to me for channels I’ve followed for YEARS. I first noticed it when following “Street Banditos” full carbon 240Z build. I would have to keep searching and re-follow. 🖕🏻YT!!!!!!!!!
The more I watch your stuff, the less afraid I am of the wires, sensors and all that jazz that comes with EFI. #CARBLIFE
The wires are easy, it's the tuning that's much harder
Thanks for this. great video. Surprised these are still aren’t sold out everywhere. Seems like the best bang for the buck when it comes to dashes.
Please do a video comparing the functionality of them all!!!
You you have been an incredible help. I bought your stuff from you guys. You’re your system you use some I suck with computer technology. I’m learning as I go much. Chevelle runs pretty good for what it is. Very nice actually Laguna Chevelle Laguna it was a big block issued 1974 or generation super sport S3 sweet car so great work keep up the good work thank you.
I got 1 of the blemished units off eBay and so far, I really like it. A few problems the boost channel doesn't show anything, it just stays at 0. And it seems you can't add custom channels to the display, which is weird because with the 3.5 I believe you can. Maybe a future firmware will fix this. I tried to update it to the SD contents on the website, but it won't let me remove what is currently on the SD card. So I have some tinkering to do yet.
ever figure this out? mine randomly flashes "ERR". i cant seems to figure it out.
@@itskamel I did figure out my problems, it was firmware. After I got it to update the boost channel works and I can add any channel I want, even the can module channels. After this however I did notice some of them will show error intermittently, only comes up for a second and goes away. Maybe a future update will fix this idk
Sure wish the 7in dash had these functions on terminator x
Can you run multiple of these dashes on one ECU ?
For instance could you run 2, or even 3, with a Dominator?
Or one of these along with the 12" Pro Dash?
I know you can run the 3.5 alongside them.
I was thinking either a 12" or this 5" for the main cluster display and another 5" for an auxiliary display somewhere else in the dash - like the middle or console area that you could keep another set of parameters displayed on.
So the pro dash doesn't have a log trigger BUT the basic screens do... so odd. I'd even burn an input to have a physical log start/stop option!
What sucks is, this will work for the Atomic 2, but tech support told me I'll lose some of the Atomic 2 functions on the display, even though they run on the same firmware. 🤷
Hi! Grate video. Just to know, is iut possible to use that GPS to activate a "speed limit" or "cruise speed" if you use a Holley Sniper Efi? Thanks!
Question: when doing 12v electric installation, I get there’s a couple different types of products to use. The one thing I’ve noticed lately is guys using more of the pre wired solenoids with the pigtails over using the all-in-one leash board or even them Amazon cheap’y fuse/relay boards or fuse boxes.
Hey Joe,
Can you display custom sensor such as trans temp on the display.
Good to here that you can run a 3.5 dash at the same time so log on 3.5" and still read the gauages on the 5" dash going down the track.
Never worked out how to display custom sensors on the 3.5" dash
Thanks for the great info on the holley products.
Joe so I wouldn’t need the 3.5 inch display to run wizard n such I can just get 5 inch? Just making sure plan on upgrading to sniper 2 this winter I had a nightmare with my sniper 1 lol. I just like thought of efi on my old car 👍
Do they sell just the display and conector too the dominator if yes can you give me the part number ?
Excellent review, my 3.5 is laying on the floor 😂
Your GOING to step on it one day. Pick the fugger up
holleys ganna sell a ton of these. people are struggling to afford the stuff they want. When they release
options like this that the average 50-70k worker can afford. its a big win.
yes the price is awesome. its going to be interesting to see how things go the next few years. its pretty obvious people want less expensive stuff, look how the terminator X series of ecu's absolutely exploded with popularity! a prodash with a terminator x is kind of a weird combo,the display is 2x the cost of the ecu. this unit makes far more sense for most applications i think.
@JoeSimpsonAtTempest yup. I just hope they add more background layouts, and it will be an awesome purchase.
@@JoeSimpsonAtTempest not to mention a gps speedo gauge setup cost over 350$ after its all said and done. Big value there alone
I have a sniper XFlow on my 69 Nova. Do I download the Terminator X software to my laptop ?
Joe, is their a separate CAN connect for the pro dash or is there only one? I need to run the wizard again because i going to get new injectors, i dont want to have to undo all my work when i end up getting them so i want to leave the handheld connected as well as the pro dash. Should i be looking at getting that CAN splitter cable? Thanks
Hey Joe I see you have an injector cleaner / tester. How do you like it and what brand is it. Thanks
I'm in the process of putting together my NA sbf 408W with an AOD/4r70w. Which system would you use the terminator x or sniper.
Can i read a datalog file on the display screen?
I bought one of those and my software has to be updated. Currently running V2, which update should I load?
Will it show flex fuel content?
I ordered the 553-200. Says sniper efi. Is this an older model? Will it work with the dominator?
So can you run both the 5” and a 3.5”? I have my 3.5 mounted and I’ve been putting off replacing my cluster. This would be nice as a cluster replace my while using the 3.5 for extra gauges
Yes just need a splitter cable
So, the 5" dash is the ONLY dash that Holley sells that advertises that you can "Tune" with a Terminator-X system. For some reason, ALL of the larger dashes specifically say that they "Do not support tuning with Terminator-X systems."
Does this 5"dash support FULL tuning? Like that it could take the place of having a laptop, and be able to tune ALL the parameters?
@@davelowets no - the laptop based software will always be 1,000% better for tuning with any of the dashes or ecus
Yeah I gonna keep saving up for a pro dash.
Wilm this work for msd atomic efi?
Is the an Odometer feature?
Nice thanks for the intro
Does the speed get logged to the datalog? This is one channel that I really miss when tuning or rather reviewing Sniper Datalogs.
I'm also interested in how well the triggered logging works. When I remember to log with the Sniper, I often forget that I have to manually stop the log before shutting the ignition off, or that log is lost. I've lost hours long datalogs that I wanted to review for long distance economy and transitional states. I assume that the triggered logging will also stop and save the log at key off?
I have a X-Max with a pro 6.86 and the speed IS logged on my log files that I hit record on the plugged-in laptop. Logging will stop when the car is shut off - I've had the car die and when I restarted the engine, obviously the holley power cycled and the log file was still saved on the laptop. Not sure about internal logging -
Nice upgrade. I hope it drives down the price of used 3.5" displays
Question for all as I'm lost. Is terminatorX a newer version of the original Terminator? I have the Terminator Stealth system and as I sometimes do research for adjustments I notice everything is now Terminator X. Is it the same thing?
The old terminators are actually hp ecus and better than the terminator X’s. Not sure how they decided on naming them so confusing
Thank you for the clarity. When you don't live or play with these systems daily and suddenly need some advice or knowledge and start researching and everything says terminator x you start wondering what you missed
Will it read boost instead of kpa. Ain't nobody got time to look up what a kpa is
of course, you can display boost on any of the holley displays/software
So can you reuse the spots for tach and speed, or is it locked to those?
you can change them. touch the gauge, hold down, let go, go to edit, and edit the channel.
@@JoeSimpsonAtTempest. Excellent. Thanks!
@@JoeSimpsonAtTempest Can you screenshot a list of the different parameters that you can display on this unit? I'm looking to see if I need to buy aux gauges/indicators that make sense or if it can display everything I'm looking for. Need to see if I can put fuel level, turn signals, high beams, etc on this display in addition to boost pressure meth on/off, etc.
Is this just specifically for the Sniper series? Or can this be used for all the Holley ECU's across the board?
All of them. It was originally for snipers only. It was connected to a terminator x in this video
Is it still not compatible with Sniper 2?
Just missing a built in shift light!! 😢
Its super easy to setup thru holley if you want to do it, get a small super bright led light, mount it wherever you find it conveniently lighting up into your face and make holley turn that on at whatever rpm you like
@v8tergt653 right but im on terminator so I'm out of outputs
@@stealthybrandon Yea time to get a can i/o module or dominator 😖
leave it to holley to use a non standard automotive connector that sticks straight out the back, and not give you the ability to configure the layout.
This should be included, or at least a $150 add-on..
Man! They SHOULD have put the GPS terminal connecter down in the CANBUS connector end of the cable, so that you dont have 2 cables hanging out of the display. Fail
5 inches is what some say, is the perfect size....
TIME FOR SOMEONE TO CRACK THE SOFTWARE AND COPY OVER THE PRO DASH PROGRAMMING TO THE 5"!!!
I think the 7 inch display is perfect size for a street car. Jealous that the 7 inch screen doesn’t come with a GPS module
you can buy that cheap
I love my 5” screen. Soo much easier to use.
Was this video sponsored by Holley?...it feels like it is .... !st half was like I'm watching an add for Holley... they gave you really good talking points...for $409.95 seems a little over priced
but for the 7 inch being around double the price, it makes the 5inch the best budget option unless you wanna do a 3rd party screen like tinker electronics.
oR! RUN a android pad at any inch you want lol
hmmmm... well isn't that special. . . #churchladyvoice lol
For it only being $100 dollars more than the shit 3.5” one, Holley’s cheap assh*les better start putting these in the efi kits…
Especially for their wiring harness being complete shit… they can’t even route the wires in the right directions in their harnesses… Tps, and iac won’t even reach the throttle body on an ls2 with their own high ram intake lmao 😂
Next one I do, going to give FuelTech a shot, even though it’s about $650 more… if it’s a better fit and quantity, it’ll be way worth it… Well by the time you buy $170 coil harnesses that aren’t included, and 3 ICT billet extensions… not a $650 dollar difference anymore…
FuelTech's 25 year old fuel modeling should be a nice surprise for you.... there are so many better options for the price but people are just enamored by the marketing.
why cant they just wifi or blue tooth. edlbrock have a better idea with the android so you can use anything you want