Well done. Thanks for putting this up, as I have this task ahead of me on my '51 3100. I shall refer back to this when the times comes. Color even looks the same, I used Ford Chrome Yellow. The old Chevy doesn't seem to mind a Ford color, so it is all good.
Thanks for the nice comment. Your first series may be different than mine. I believe yours uses wood block spacers. On mine, the front bed panel sits on the leading edge of the boards, it is not bolted directly to the cross member. Good luck with your project!
Good luck with your bed, I hope my video helps. It went smoothly because it was the third time. I had to make a lot of adjustments and do some cutting on the wood before it fit perfectly.
Thanks for the comment. This truck started out as a 2 wheel drive. It requires a few holes drilled in the crossmember and frame to install a NAPCO 4x4 system. It is a bolt up affair. This driveline came off a 58. Just go find the parts and convert yours.
Yes it is. I just had the cab completely redone, & repainted in it's original black. I rebuilt the engine (a '69 327 from an Impala). I have a few more mechanicals to do on it, as well as building the bed ,& it'll be ready to go.
@OldVideoMonkey Yellow is beautiful on these old trucks. Mine is Corvette Yellow. There are a lot of differences on the pre 55.2 beds, but I hope the video helps you! You have wooden blocks to deal with on yours if I remember correctly?
Your garage must be immaculate! I could never go barefoot in mine! haha. Do you know if those clips that hold the sills in place are available aftermarket? my truck came without a bed and all I can find are the rubber pads. Thanks!
Thanks for the comment. I like the 68 year, is it a 4x4? Look at the description of my video to find a link to the finished truck. Or look at my other videos. It was a 6 year labor of love.
I am pretty positive you need them to raise the bed to the correct height. You should buy the factory manual so you can see how those go in. You might be able to find a diagram online somewhere or go to stovebolt[dot]com Good luck!
You can buy the bed sides, front panel, and tailgate from Mar K. Then buy the wood and the stainless strips with a bolt kit and you are good to go. I used the original bed sills and fenders. As you see in the video I had to dado a channel on the outer two bed strips so they fit nicely under the bed sides.
WOW!!! Very nice truck. Thanks for the educational video! I have a 1960 Chevy truck and the time will come soon for me to replace the bed wood.....
Great job ............ VERY nice '55 stepside. Congratulations!!!
Nice truck...AND a NAPCO !!! I have a '68 K-10 that I'm doing a wood bed for. Good luck w/it.
Very nice job! That bed turned out great. I'm just getting started on a '56 Stepside 4-spd
Well done. Thanks for putting this up, as I have this task ahead of me on my '51 3100. I shall refer back to this when the times comes. Color even looks the same, I used Ford Chrome Yellow. The old Chevy doesn't seem to mind a Ford color, so it is all good.
Great job! I've got to build my bed in a few days.
Thanks for the nice comment. Your first series may be different than mine. I believe yours uses wood block spacers. On mine, the front bed panel sits on the leading edge of the boards, it is not bolted directly to the cross member. Good luck with your project!
Nice truck
Good luck with your bed, I hope my video helps. It went smoothly because it was the third time. I had to make a lot of adjustments and do some cutting on the wood before it fit perfectly.
Thanks for the comment. This truck started out as a 2 wheel drive. It requires a few holes drilled in the crossmember and frame to install a NAPCO 4x4 system. It is a bolt up affair. This driveline came off a 58. Just go find the parts and convert yours.
Outstanding BTW
Thanks. The wood has been holding up to weekly trips to the dump, scratches and Florida sun. I'm glad I didn't go with a varnish finish.
Wow, that video didnt seem anything like 17 minutes... All I can say is that you have a new subscriber...
Yes it is. I just had the cab completely redone, & repainted in it's original black. I rebuilt the engine (a '69 327 from an Impala). I have a few more mechanicals to do on it, as well as building the bed ,& it'll be ready to go.
@OldVideoMonkey
Yellow is beautiful on these old trucks. Mine is Corvette Yellow. There are a lot of differences on the pre 55.2 beds, but I hope the video helps you! You have wooden blocks to deal with on yours if I remember correctly?
Sweet video man! are those bias ply tires? Wish my 59 was a NAPCO.
I am building a 1958 Chevy short bed step side Your Film. will be Helpful When I Get to the bed.
Nice build; Question, I'm putting together a bed for a '51, but on the bed sills I have wood blocks do I need them or r they optional?
Where did you buy the rubber seals for between the rear fender and side bed panel.
Great video .i have a 1957 chevy truck that needs a bed. Where did you buy your bed?
Your garage must be immaculate! I could never go barefoot in mine! haha.
Do you know if those clips that hold the sills in place are available aftermarket? my truck came without a bed and all I can find are the rubber pads.
Thanks!
Thanks for the comment. I like the 68 year, is it a 4x4?
Look at the description of my video to find a link to the finished truck. Or look at my other videos. It was a 6 year labor of love.
Were did u order the bed parts at
How much do those metal strips weigh altogether
I am looking for a truck like this to buy I love the yr. and style
I am pretty positive you need them to raise the bed to the correct height. You should buy the factory manual so you can see how those go in. You might be able to find a diagram online somewhere or go to stovebolt[dot]com
Good luck!
I know the boards are a kit , is the bed a kit?
You can buy the bed sides, front panel, and tailgate from Mar K. Then buy the wood and the stainless strips with a bolt kit and you are good to go. I used the original bed sills and fenders. As you see in the video I had to dado a channel on the outer two bed strips so they fit nicely under the bed sides.
That 2nd sieres gmc is in ment condition
Chevy not gmc
Not sure, maybe a 5-10 pounds.
And so whats the name of that yellow?
It's a modern Chevy yellow that they use on the corvettes. There was a Yukon Gold available in 55, but it had a more orange tint that I didn't like.
Shite...
Was it just me that thought that first panel was the wrong way round??
Blutu