Differences In Stroker Engines
Вставка
- Опубліковано 25 сер 2024
- To have an engine make more power a common technique is to increase cubic inches. That can be done 3 different ways: increase bore size, the length of the stroke, or a combination of the two. The term stroker is used when referencing high-performance engines but let's get into what it really means.
A stroke is an engine that has the stroke of its crankshaft increased beyond stock specs. This mod can be done 2 different ways. First, you can offset grind the crankshaft. Before after-market crankshafts were readily available, the crankshaft's rod journal would be intentionally ground into a smaller diameter and to a center line further from the actual center of the crankshaft. This effectively lengthened the travel of the piston in the cylinder, increasing its cubic inches. With the offset grind yields a small increase because the crankshaft can only be ground so much. In addition, it was labor-intensive, expensive, and potentially weakened the stock crankshaft.
The second method is to replace the stock component with a purpose-built aftermarket crankshaft. These are designed specifically for longer strokes, are constructed out of better material, and are built to yield maximum cubic inches without sacrificing strength.
Stroker engines are categorized into 3 types: over-square, square, and under-square. Over-square means the bore is larger than the stroke, square means the two are equal, and under-square means the bore is smaller than the stroke.
Over-square strokers are common in most racing applications. The larger bore and shorter stroke produce the needed air displacement while keeping the average piston lower at high RPM. This improves reliability and allows for efficient air induction.
Square strokers have a good balance of horsepower and torque production. They can be tailored to make stout low-end torque or high-end horsepower depending on the components selected. They're excellent for weekend warrior race cars and high-performance street cars.
Under-square strokers shine in lower RPM and high-torque applications. When the engine's bore size is limited, an aftermarket crankshaft will increase the size by 60-60 ci.
Several aftermarket companies offer not only stroker crankshafts but entire rotating assemblies with all the associated parts to get your bullet together. The only thing that limits stroker applications are the physical size of the engine block and your bank account!
Websites:
www.PowerNatio...
www.PowerBlock...
Facebook Pages:
PowerNation - / powernationtv
PowerBlock - / powerblocktv
PowerNation Daily - / powernationdaily
Detroit Muscle - / detroitmuscletv
Engine Power - / enginepowertv
Truck Tech - / trucktechtv
Xtreme Off Road - / xtremeoffroadtv
Twitter:
PowerNation - / powernationtv
PowerBlock - / powerblocktv
Instagram:
PowerNation - @PowerNationTV
PowerBlock - @PowerBlockTV
For more on PowerNation, check out PN+ at bit.ly/2oTCIyJ
I'm in the minority by liking short stroke engines. Like the 327 Chevy and Ford 302. They wind up fast and will scream lol
would a bigger cam be recommended for a daily driven ls3 if I were to get it stroked ?
so, by increasing the stroke downward, you will get an increased upward stroke or TDC, so you use custom made shorter pistons.
Can you guys do a 396/402 bbc build
Ohhh I love a good stroke every now and then. I'm all about cranking my shaft and giving it a good stroke as well.
Boss gd afternoon,,where is the more power,,long rod or hi stroke,,?😊
Thanks for the informative vid
Why not do a 2 stroke conversion:www.4btswaps.com/attachments/2cyclesbc-jpg.6839/
400 sbc crank in a 4.3L? cut and mill the end to match the 4.3L?
would you need the 400 cam?
Well I don't think that would work.
You would end up with a 271 ci v6
The main journals are bigger on a sbc 400 and the cross plan crank would shaped like a Y in the v6. The V8 would be a +.
So over all possible but unreasonable.
@@Soundsofthewood Stroker
@@kingjeremysircornwell7847 over all you'd be better choosing a different engine. I don't know what you are looking at putting this in.
If you are looking for something weird then get a straight 6 gm engine.
@@Soundsofthewood I'm also running 2.8liter Fuel injectors. And seat foam in my air cleaner. I'm adding manual steering and flame thrower ignition box next. lowered 2" inches with revers wheels and wheel spacers. Fire & Brimstone
Bank account lol
Doesn't increased stroke limit rpm in turn affecting peak hp?
jayknight139 I think there’s a ratio where increase stroke increases torque and hp and there’s a threshold where it flattens out. Increasing stroke allows more air and fuel
@@WesternReloader ok that makes sense. And I would like to know more about this because most racing that I'm aware of like motorcycle and f1 stay away from increasing stroke to much because they operate at high rpm. But for street use it might be great.
@@jayknight139 Do something like this:www.4btswaps.com/attachments/2cyclesbc-jpg.6839/
@@jayknight139 yeah you wanna crank a longer stroked engine a little less like the 383 vs a 350
I need help with purchasing the right engine. I recently just purchased a 1979 Chevrolet Malibu (V6) and I want to swap it out with a V8 engine. I’m also a 1st timer so I need a ton of advice.
build a 632 or 638ci BBC for it, or buy you a Chevy crate engine 632ci BBC that makes 1,000 n/a hp.. Or an LS7 that makes 505hp n gives good 25+ hwy mpgs.. Or any other, but why go with any other engine than those 2?? lol..
Does bigger bore better top end?
In n/a it would but in a boosted engine it would be better not to risk making thin cylinder walls
@@jayknight139 unless you have an aftermarket block or had your block concreted or have had a good set of aftermarket sleeves put in your block but yes your right if you're working with a stock block with stock sleeves and nothing else than it is a good thing not to go too crazy on having your block being bored out too much and just go with a stroker kit which is longer rods and a bigger stroked crankshaft like taking a 350 SBC and putting a 400 SBC crankshaft in it thus turning it into a 383 stroker or taking a 400 block and putting a 350 crank in it does the same thing but I do believe if you do it that way you have to use a 6.0" rod and if you were to use a 350 block with a 400 crank than you could use a 5.7" rod
@@keefespencer1173 the 350 crank in a 400 block makes it a 377
I'd like a 425 small block oldsmobile out of a 350 oldsmobile diesel block... care to take a bad check lol 😆
I have a question about.
I am dealing to buy a Trans am 1977 From Germany.
This man buy it from Florida,and the car it doesn't have the original motor (4,9 turbo) instead it has a 350 block with 383 stoker.
The motor is ebelbrok. I don't know what does means because here i live we don't have those types of cars or engines.
And also if i buy it can i find parts from USA???
I am waiting for your answer.
Regards from Greece
it means that the 383 stroker engine is originally a 350 ci small block (5.7 litres) bored 0.030 over ( a 350 cylinder diameter is 4 inches and has been increased to 4.030 inches). then a bigger crankshaft has been installed (3.48 inch for a 350ci, swapped for a 3.75 inch ). the combined cylinder diameter increase and bigger crankshaft increases the overall volume to 383 cubic inches (6.3 litres). more volume means more power. 383 engines are beasts! You can find parts at various shops in the usa and import them easily to europe. some car shops in germany and france also have parts (although in smaller variety and quantity). I hope I answered your question buddy. take care.
What heads are best for a stroker, like a 383 chevy
Dart iron eagle
Short stroke big bore common on a lot of racing applications
Why people think that’s false is beyond me
i'm taking my 4.6L 2v n stroking it to 5.0L n 0.030 over, if not it'd be a 4.9L or a bit less..
So how big can a mopar 383 or 440 be stocked too? Low end mild Thumper two balls to the wall all out race motor
I've built a 526 in a factory 440 block and it wasn't terribly difficult.
@@DaveMcLain what rod size did you use? im buying parts for mine and i thought 💭 7in long rods will fit? or at least longer than 6in with stock ( 10-12in ish aka no decking down ) RB deck hight aiming for higher compassion thats why i picked it / big cam so it needs it. crankshaft throws are 4.5 in as thats the biggest one that fits a stock block without grinding
@@richardprice5978 The customer had supplied a kit for that build and that engine used a 7.1 inch rod with big block Chevy wrist pin and rod journal sizes. This engine had a 4.375 stroke and it was easy to make it clear. You'll be getting another .062 closer to everything but that shouldn't be a whole lot more work.
@@DaveMcLain thanks im going for stock sizes of bearings or bigger sizes ( aka ford 460 bbf as i don't trust my engine to K24 Honda sizes ) as im not planning on reving it past 6k-6500 rpm but it basically going to have the same loading as a heavily loaded industrial / marine / blower motor / big gulps of nitrogenous
@@richardprice5978 The rods for the 2.375 journals have the bolts spaced wider than a rod for 2.200 journals usually. On the big Chrysler engine getting the rod past the place where the oil pickup screws into the block is the problem. I've done a 4.140 stroke with an Eagle rod using the Chrysler journal and I had to do some grinding to get past that boss on the block. With a 4.375 stroke and a similar rod made for a 2.200 journal I had to grind a very similar amount. With a 4.500 I think it'll be close to impossible with a larger journal than 2.200 without going with an external oil line to the pickup.
If I change the stroker crankshaft, do I need to change the piston and conrod?
Typically you need a piston with a shorter compression height. Some situations do need a longer connecting rod.
Skyline Fever thank you man
3rd way,,weld journals and grind,,,,The old way!!!
No.