Ford Mustang: Crank no start - No fancy tools required
Вставка
- Опубліковано 9 вер 2024
- This 2000 Ford Mustang is fresh off the hook, and I'm bringing you guys' along real time! Customer stated that the car will not start! He replaced the battery, and it still isn't starting! What's going on? Well let's find out, follow along as I take you through some basic troubleshooting using some basic tools. The Power of a test light AKA "my scope on a rope" Hope you enjoy it! Thanks for watching
- Авто та транспорт
Thanks from all of us that can’t afford a $1000 scanner.
You welcome 👍
If u have an auto zone near u, u can rent one for like 10-20 bucks and when u return it, they give u ur money back
This is the best troubleshooting video for these models of Mustang fuel pumps, the wiring diagram is very useful.
Excellent methodical fault finding, at the roadside we used to listen for the fuel pump at the fuel filler , mind you we nearly always had the driver of the broken down vehicle to turn the key!
Thank you Kevin! That’s a great suggestion to listen at the pump.
Ooooo. I see no fancy tools and I am already hooked in to watch !
Great process like always. 👍
Thank you Keith! After editing, I’m realizing I tend to drag it out more than I need too sometimes, with hopes it may help someone with less knowledge. The old scope on a Rope never lets me down 😄
Saw Will on your PHAD live stream. Nice of you to return the visit he made. Seems good techs tend to show up in the same places.
@@robinsonsauto wondering was it the fuel pump? I've seen a lot of videos with mustangs having fuel problems. issues with pats and not the actual pump thank you
Being lazy I'd try a squirt of brake clean down it's throat. Then if it's still no start, on Fords, especially with TFI {cause I have seen them fire the plugs, but be dead on the injector pulse.} I usually do noid light on injector, fuel pressure gauge on test port, and a spark tester on the plug wire 3 quick tests at once. With no fuel pressure, ck fuse, inert switch, then go to tank with scope on a rope..But for you trying to help DIYers you approach was spot on.
I can resonate with your experience man! I've been on my first Mustang job ever - fuel problems - starts, runs ok until operating temp. then breaks up and shuts down...GrrrrRRRRRRR! I try to view the engine compartment as you record - I also have the 3.8 (not MINE) belongs to a non mechanical friend... FUNNY! I like the part about the mouse! I have gone thru that too - livin in the woods having nests in my air cleaner, in the trunk, under the seats, even had 'em running up over the pass seat while I was driving... kept thinking I was seeing floaters moving in my peripheral... sure enuf... little bastard was freaking out cuz the car was moving! The one I'm working on is a 2001/3.8 so like I said, I'm trying to glimpse the engine compartment for similarities to my issue. The FP fender relay location is an absolute engineering joke!!! PLUS I understand the relays are SOLDERED in. C'mon Ford - get a clue!
Im having the problem that you describe buddy with my 99 mustang . Need help did you find the problem?
Great video Will showing your thought process. One quick way to hear the pump is to remove the gas cap and place ear close to filler neck. Of course, it helps with two people or you could use the microphone on the camera. And like you said, go for the easiest stuff first. And no troubleshooting steps are wrong as long as you get to the final culprit. And man, that shop was cold watching you work. Take care Will and wishing you the best!
Thank you! If all else failed I wouldn’t have blew the dust off our old scope 😄 I couldn’t keep up with the cold last week! Thank you again
And that’s a great Tip using the filler neck!!!
@@robinsonsauto When I was by myself Will, I would just pull the relay for the fuel pump if available and jump across the female contacts and let the pump run. Then I'll just go back and listen through the filler neck to hear the pump run.
@@robinsonsauto It sounds like you might need to get a mini-split heat pump for your garage. I installed one for my garage a few years ago, and it's been a nice addition. Take care and stay warm. I'm ready for the warm weather.
Qa@@stuzman52
Hey Will, better set some mouse traps in your shop. That mouse probably jumped ship and is now living in your tool box. :)
😳 I didn’t think of that! lol wouldn’t that be something
Looked like Mickey had a cozy little condo in there!
Lol 😂 we all gotta try and stay warm somehow. Glad to see he’s behaving back there
Lol I just had a no crank no start today that kicked my a$$ 3 1/2 hrs chasing a wire that should took 40 mins tops. First mistake I made is trusting the other shops testing (I know that's a big no no but I did). So instead of starting at the easiest testing location I went straight for the pcm thinking they already tried the basics. It took me 40mins just to get to the pcm and do my tests. Then after that checked out I went to the ignition and found a missing power. The power came from the fuse box and for some reason alldata wiring diagram sucked for this certain truck. It labeled 10 red wires as ignition feeds and nothing else plus they all said C1 (I think they accidentally wrote it wrong) . So I checked every red 12/14 gauge wire. All checked out plus I unplugged it with a test light in series a tried to see if I could find it that way. One test light to ground on ignition power I'm missing and touching each red wire with a test light to positive no luck no light. Now Im thinking I have a broken wire from fuse box to ignition. I spend another 40 minutes removing part of the dash only to find everything checks out. I go under the hood remove some brackets and by luck I find the red wire do my series thing and find out I only have 6 inch left before it goes back under the fuse box. So I remove the fuse box for a second time and find the problem. The freaking wire was burnt and changed from red to brown so I didn't see it. I swear it looked like it was made brown. After unplugging that leg of the box you could see it clearly. I unplugged everything but 2 connectors because they didn't have a red 12/14 gauge wire I thought.
Man that’s a good catch in the end! Trusting other shops and wrong service information at times has led me to redoing prior work/tests just to get back to square one. It’s the worst feeling. I can feel your frustration. the time and effort it takes to trace out the system, not just physically, mentally as well. Most will never know this challenge, especially while being under the gun. Being persistent payed off.
What do we do in these cases?
I feel we should get paid this time in full?
especially if others where there already.
This experience will add another notch to your already great Skills . These experience make us better and can be the most awarding feeling of accomplishment.
It’s a repair that can’t be referenced in a time guide or predicted..
Awesome video thank you very much buddy nice to see you again thank you
Thank you! It’s great being here. Your welcome anytime
Great troubleshooting, I like that way you explain, thank you I be following you.
Good video Will! Great to see you back on line.
Thank you Bart! I appreciate it. Great being here
That was an easy one Will!
Thank you James! Yes easy peasy
I cut hole in the trunk above fuel pump. Did not have the jack to drop tank. The fuel pump is right below your spare tire in trunk.
Thanks Will I appreciate u using your time to educate Cheers
Thank you Anthony it’s a great feeling cheers
Nice review of the process, I would have checked fuses and relays first, also good to check when u got a mouse in the house for wire damage, it’s looks a little chilly in the shop, thanks for posting this frosty vid, stay warm!🥶
Thank you! it’s the times When I skip ahead, that I often find myself tracking back to the beginning latter. Definitely a great place to start…
Yes it’s been a nasty week! Soon as I get heat some heat in the shop, I end up letting it all out with the bay door.. I’m to hot in the summer and to cold in the winter ❄️ 🤷♂️
very good video, thank you
Thank you Annie
This looks just like my 98 v6. That is exactly what mine is doing.
Very nice video.
hello... I have a 2000 Mustang gt that I just did a swap on.... The injectors and coils have no polarity on the ground end.... They have power but nothing from the ground which is creating no spark and no injector pulse for the trigger wire... Do you know what that could possibly be or could you point me in the right direction?? Any help would be appreciated
I did not find voltage at the fuel pump connector or the inertia switch with the ignition switched to the on position, the culprit and easy fix was a 30 Amp fuse that protects the PCM module. The symptoms were the car would not start, the anti theft light flashed quickly and there was no odometer reading. I don't know what caused the PCM fuse to blow, I am a little worried that it could happen again while driving again on a slightly bumpy road.
Myself I just took the intake off threw a little starter fluid and it fired up from that just time to replace the fuel pump
your diagnostic was done very well .but for me i would did is spray brake cleaner in trottle body to see if try to start .thank great video
Thank you! Yes quick easy and effective
I'm gonna try that first. Mine won't start as well
I'm curious- was this Mustang's theft light flashing when it wouldn't turn on?
Mine is doing the same exact thing- wasn't turning on, figured it was the old battery dying from sitting there for a few years. Got new battery, theft light flashing, crank no start. Suspect it may be the fuel pump, just don't see what that would have to do with the theft light flashing. Hoping it's a simple fix like this though
nice laid out video here. my old 95 Lexus sc400 that has been sitting for 3 years will crank and crank but no start. after about 3 attempts it will turn over and run fine with no issues. I tried tapping on the tank and that helped one time. i also siphoned the old gas and replaced with fresh gas and at that helped on another time. The problem is once i have it running and turn it off then go to restart it after 30 minutes it wont restart. Can that be the relay or pump? Can I eliminate going down the spark route since it already has turned over and ran fine or will something in the spark chain cause these intermittent issues?
Any resolve?
The mouse picture 😂
just went through this. -27f morning 14 month old group75 650cca acdelco battery was dead battery charged it would no longer hold charge went to dealership with 2nd vehicle got new 700cca acdelco battery but absolutely would not fire could clearly hear fuel pump running every on/off cycle of ignition poured some gas down throttle body it started/ran good then shut off poured more gas down about 4 more times its been working since not sure what was wrong but beginning to think battery charger wrecked a $182 battery that should have lasted more than 14 months. my car is coil over setup
brrr now that is cold!!! I’m sure many things have problems at those temps 😬 including myself I’d be useless probably 🥶 when we get down near 0 here, I see so many battery issues and strange things. Really hard to say, I can relate to this to a certain extent
Thank you sir; Great, easy to understand troubleshooting steps in solving the no start problem. Please give us a update on this stang, I have a Fiesta 1.6 liter five speed manual. Love it.
Fiul pump you have to put fiul starter inside the intake
You didn’t check the CCRM
Yes, I was driving my Mustang n I had a flat and I drove to the tireplacion on the rim. My car will not stop what is going on.
I got a mustang It has similar symptoms I just replaced the fuel pump it cranks no start. Do uk wat it could be
I have the same problem if any help?
Me too what’s the fix
What if the fuel pump was replaced but the fuel pump fuse keeps blowing when you try to start it. What could be the problem
Maybe a faulty fuel pump or something got pinched/shorted out during the installation.
Sounds to me there is a crank going on. Nice video moving on..
Probably not going to respond but how do I check fuel pressure if I don't have a fuel rail access port
Most times in that case you need to separate the line at a fitting and use an inline adapter
95 Accord Will Roll Start , but when you try starting it with the key using the starter which does crank. The car won't start? Any suggestions? I sure would appreciate it !
Just put an air line with a rag in the place of the gas cap and if it starts .....you got the problem
I think this rusted tank would drain itself 😂 this one wouldn’t make a good pressure vessel
If it doesn’t start the fuel pump the culprit..especially on electric fuel pump..I was told bang the gas tank underneath few times with a shovel..😂😂I tried it and it started..funny ford cars..
yup that will get you home or to the shop most times. same with a bad starter. tap tap
Any ideas what would cause intermittent no start on a crown vic. Now it has no check engine light and no communication. No crank no start
What checks have been done so far? No communication? How was this determined
@@robinsonsauto plugged a scanner in it said no communication. If you put power to the wire from the fuse box to the starter it will crank it cut off going down the road
@@jacobdykes6736 I’d probably Grab a schematic and find the easiest place to check ignition voltage as a starting point. Run through Power/grounds and what not.
Has this been done?
@@robinsonsauto no not yet
If there is 12 volts at the switch does that mean it's bad
Mine is having the exact same problem but not my battery is fully dead so now it will not even crank up
Hello I got the same problem right now. I have a 2003 mustang GT 46 motor. All the fuses are good. I replaced the brain underneath the passenger fender thank God I didn't have to remove the fender I just dropped the splash shield and I got to it. I replaced that I also replaced the fuel pressure sensor on the rail. I replaced the throttle positioning sensor. I replaced the cam sensor right beside the AC compressor which was a pain but quite easy. The inertia switch in the back. I tested that that's good I tested the tank red and black wire. Which was good ignition on it lit up nice ignition off it shut down. Here's where it gets tricky I dropped the gas tank. I went and I bought a brand new fuel pump. Lifetime warranty is called precision for the 203 mustang GT. I installed it plugged everything in. And I still have no fuel pressure. The pump does not turn on doesn't click. Do you have any suggestions. I'm thinking I got it effective fuel pump even though it was brand new. I normally do not give out my email address. But I would really appreciate it if you wrote me back. Course let me know who you are hopefully I want to talk to you the one doing this video. I would really appreciate your help. Now I did notice on the precision pump the wire colors were different from the original fuel pump. I was wondering if that made a difference or could make a difference. I think I have suspicions that the wires might be in the wrong place.it might be a hangover rebuild or whoever put the fuel pump together didn't know what they were doing. But it looks like I got to pull this tank again. Anyway please email me as soon as you can. It's August 26th 2022 on a Saturday my email address is actordanielunger@yahoo.com.
Same problem, did you find the problem
👍🏻👍🏻👍🏻
Grasias
I pulled the hot post no good
So what was wrong with it?????
He don’t know 😂😂
Mines is doin this now it’s a v6 3.8 94 help!
What did you find out??
Fiul pump ded
Check for spark and if the fuel pump is pumping fuel...if not check ign fuse and fuel pump fuse... If good... It's the ECU
In the passenger foot kick panel. The ECU is bad
Thanks Will I appreciate u using your time to educate Cheers
Your welcome Anthony. It’s my pleasure! Truly enjoy it cheers 🍻