BMW N63 engine PCV valve replacement crankcase pressure valve 550i 650i 750i 750Li X5 X6 50i
Вставка
- Опубліковано 5 гру 2019
- Welcome to I.E. Euros.
Hi, I am Francisco.
We are a group of vehicle enthusiasts looking for Car meets, car shows, drag racing, roll racing, New cars, etc,..
We love performance vehicle
BMW MBZ AUDI ASTON MARTIN VOLKSWAGEN MINI FERRARI LAMBORGHINI LAND ROVER JAGUAR PORSCHE
DODGE TOYOTA NISSAN SUBARU CHEVY CADILLAC MITSUBISHI FORD HYUNDAI KIA LEXUS INFINITI
We are in the Inland Empire, CA ( Fontana, Ontario, Rancho cucamonga, Riverside, Colton, Bloomington, Rialto, San Bernardino, etc,... )
Subscribe to be part of the group and to get all the newest content we upload.
Want us to check your ride?
Email us
i.e.eurosforlife@gmail.com
follow us in instragram
/ francisco_amaya_youtube_ 🏎🏁🎞🎬
dod_noxid?igshi... 🎥📸🔊📼
check our channel for more videos
I.E. EUROS
/ @ieeuros
Check my other UA-cam channel
FranciscoAmaya
/ @franciscoamayayt
Vehicles in this video
2013 BMW X5 Xdrive50i M performance
This proces is going to be Similar to all bmw models with N63 engines
F01 F02 750i 750Li
E70 E71 X5 X6 XDRIVE50I
F06 F12 F13 650i
F07 F10 F11 550i
F15 F16 X5 X6 Xdrive50i
G11 G12 750i 750Li
G30 550i M550i
#IEEuros - Авто та транспорт
Great video Fransicso. I changed mine in a 2012 750li xdrive. A short time later I notice the plastic shattered and separated again. Instead of buying new pcv valves I removed the plastic hose from both ends of the connectors and replaced it with 5/8th heater hose I got from Autozone. I cut the hose down to size. I secured the hose onto the connectors with metal circular hose clamps that I got from Autozone as well. It's been quite a while and I'd say about 12k miles since I did this and no issues what so ever.
@@emmaomalley4582 definitely doesn't and especially here in Texas Forget bout it!!! 🥵🔥 my oil cap about 2 years ago on my 2011 550xi crumbled in my hand when I went to open... no lie like an ancient artifact like in the movies when hits the air lol
I replaced it with a mini copper hard rubber hose that’s from antrifreeze wit fits well you reckon it’ll work?
Hey bro I wanted to do this I’m just not familiar on how to. Do you have a cel number I can contact you?
Thanks, this helped me out a lot because the BMW dealership was trying to charge me $5,100. I watch all of your videos. I truly appreciate you
You’re good, you have finished the job. Lot of people will quit and complain about it. It doesn’t looks hard after all
Great video. I just completed this repair job. Fixed the problem and saved me a ton of money.
This is great video, very detailed. Thank you so much Francisco. You save me $900 from BMW dealer.
Excellent Video! Not many videos on here for the N63 engine on the E71 chasis! I'm ordering parts now to replace the Intake Vent Hose (PCV Valve), Plugs and O2, and this video helped tremendously, Thanks!
Why My suspension I'm filing veary hare my car is 2013 550i ???
Thanks for your help! I changed my PCV valve without taking it to the dealer and saved some money.
Where did you buy the PCV pipes ?
Ivan Quirino on Amazon. Honestly I had it on my wishlist for about a month before it became available. About $55 shipped. This solved my burning oil issue, I had people diagnose it as bad turbos or valve seals. To me it was worth a shot and I won.
Was it by Nova Parts Sale ?
I also have a burning oil problem and when I open my hood i have white smoke coming from these values because both sides are broken a bit. But I want to change this ASAP
My seal that your are replacing is broken . Could that cause a low boost from the turbos ?
Great video!
Thanks for this video…I was having the engine check light come on, was idling rough and engine missing, got worse over a couple of weeks and started showing drivetrain malfunctions and no power. Ran a scan tool, found multiple misfires, injectors shut down, running too lean and bad fume odor in the cabin from the vents…after watching a couple of your videos I thought it might be what you mentioned so took a look and both of my pcv hoses were broken completely. I replaced then both and now it’s running perfectly again…very happy I didn’t have to take it to the dealer…
I have this same issue, after inspecting both pcv they were both cracked, I am replacing them as we speak, I hope it fixes the check engine, misfire and burning oil im having at the moment
@@Canario52 Hope it works out for you, much cheaper fix than having to take it in...
Very good video, thank you, keep it up!!!!!
I have recently changed the pcv valve however I didn't changed the vent hose, not sure this cause an issue however after the change I am hearing some noise from the engine ua-cam.com/video/zAHutr5uP14/v-deo.html
can you advise me what can be?
Great Video very informative, man I wish you had video of changing the coolant lines over the alternator and underneath the the Turbos, these are fixed parts, but it would be damn nice to see someone actually do the job replace the lines and clean out all of the coolant leakage from behind the alternator
Great video!!! did you replace the PCV´s because you had a problem with some smoke in the tailpipe? or just because as you showed up, one of them was broken? Thanks!!!
Amazing video
Good job man. You make it look quite easy. Me gustaria saber donde esta tu shop para visitarte. Necesito un buen mecanico para mi F10 N63TU. Gracias.
Great Video. Just changed mine today. The pipe broke in 3 pieces after touching it a bit. And oil leaked out of the pipe motor entry. So that was necessary. I also need to remove other parts and need to take off the turbo charger intake you explained. You said you use a reusable aftermarket clamp. What exactly do I need to buy there? What do I need to take care of? And I have to get it before I start :) Thanks so much for an answer.
If you dig deep into some bimmer forums, specifically n63. These PCV hoses/check valve (the whole damn piece) is trash. It’s been recommended from a few n63 fellas to replace this yearly. Also saw a “upgraded” homemade modification for it with just a 3/4” rubber heater hose clamped on instead of that cheap plastic ribbed crap. Also lets it breath just a little more
Great Video!! Can u do a video on replacing the injectors on an n63 . Have looked everywhere online,but there aren't any good videos about it.
Yes, I am planning to do more videos like the one you want with all the detailed information. Just make sure to subscribe to get a notification every time I upload a new video.
Thanks
I was replacing my spark plugs today I notice one of the hoses cracked
I will be replacing both left and right
Good video, but it would be great to see how to replace the crankcase vent hoses that connect to the PCV valves. None for the N63 on UA-cam.
Would you be able to do a video installing a oil catch can for 2023 X5 M50i?
i had an issue with my 550i that was make a lot of exhaust when i stop and smelled lot of oil and also was leaking , finaly did change those pcv valve and all my problems where run away. no longer smoke or oil smell
thank you
Do you have a video on valve cover seal replacement on 2013 n63 750li
Thank You!!!!!
Excellent video. Just had the 2 PCV valves and plastic hoses replaced on my 2011 550i after I started smelling fumes in the cabin. The plastic hoses on the PCV valve assembly were so brittle you could crack and crumble it with your hands. What is interesting is that the problem with fumes in the cabin occurred right after I put in a can of Liqui Moly Jectron fuel injector cleaner in my fuel tank. Had never used that cleaner before. Previously just used Seafoam. Wondering if that Liqui Moly cleaner reacts with the plastic on this valve assembly. Yes this PCV valve assembly is a common issue needing replacement on these engines (really poor "German Engineering"...the turbo cooks this plastic PCV assembly over time). BUT, really wondering should I be hesitant to use Lidui Moly in the future due for fear it will break down the plastic on the crankcase valve assemblies? Anyone have any experienced insight on this?
hey i just seen a video about the liquid moly and they actually put it into their oil, maybe that’s why it had a smell because you had it in your gas tank instead. also i’m looking to get that exact same year and model you have anything i should look out for boss ? id love to hear back from you
i hope mine 2010 750i would be pcv valve instead of valve stem seal since i can smell oil burn in the car and some blue smoke, just wonder if it valve stem seal then u cant smell oil burn inside the car right?
Question it's possible the check engine light turn on if the PCV valve it's broken?
Good Evening, Another great video! Would adding a oil catch be beneficial to this engine?
If it is beneficial, would you need two oil catch cans?
Thanks for the video! I just saw that i have a crack in one of my hoses. Its also on the passanger side and i see some white smoke coming out of it. Can the oil consumption go up with this problem?
Yes, this can help with the oil consumption.
@@IEEuros thank u so much!
I have a replaced engine that consumes 1L/6000 km. Hope to decrease it even more with this fix!
Hi i have a bmw 750li f02 with the issue of exhaust gas smell in the car. do you know what it can come from? the exhaust manifold gaskets have been changed but the problem is still present
Hi Francisico,
I just came across your video. Excellent job.
Can the PCV valve cause the drivetrain transmission faliure with multiple missfire on driverside bank only
Curious to see if you found an answer. Everything on mine was fine until the pcv hose snapped in half, immediately went into limp mode with I’m sure the same message (not transmission message tho) and all cylinders on that side were misfiring, getting ready to replace the part, hopefully takes care of it all lol. I don’t see why not when it was working before the hose snapped.
Is the procedure the same with the TU?
hi,i have maxsimum drivetrain output not evelable,could be the reson pvc valve?thanks
@5:13 what is that hose? “Goes all the way down to the intake manifold” I broke a clip on that hose, but tbh I want to replace the hose anyways cuz it’s garbage
Would this cause a rich fuel mixture ?
Are those the oxygen sensors right in front of the mass air flow sensors you have to unplug from the filter housings? The other things with exposed wires coming out of them? There’s one on each side.
you can see the upstream wideband O2 sensors at 2:59. The two downstream ones that monitor emissions should be farther towards the back in the downpipes past the turbos.
Hi, I have 2012 550i and when i open the oil cap there is too much suction. Is that PCV valve?
Hi I have my broke from left and right side , this make Bmw Misfire?
Hola me podrias ayudar en Como cambio la manguera que va de pcv al maniful de lado del piloto no puedo acceder a ella tengo que quitar el neumático ? Porfavor ayuda !
My car starts smoking white every time when on idle more than 3-4 minutes, but i don't really see oil consumption. What is the easiest way to check if this pcv valve causing it?
This is my wife's car. Will these cause excessive smoke when really putting the gas down. It seems when the turbos spool up, it blowing a lot of smoke
I have a 2011 f01 750li xdrive and my fuel gauge doesnt work at all it stays at empty i changed the fuel level sensor in fuel tank and it still doesnt work do you know what could be causing this??
How do you take off the turbo pipes ? Mine won’t come off
Can the PCV valve make your engine light go on?
What is the part numbers for the PCV valves of 2010 X6M 4.4L S63?
Excellent!! I think there is a newer style of the PCV for this engine which connects the two PCV’s together with a hose.
these are the ones for N63TU engines, 2014>
@@michaelalbrandt3341 So it wont work for n63tu? 2014+
@@jayy7712 the work is kinda the same, its just u have a tube between both tubes, nothin special but u need to get the right part numbers for ur engine
Can you do the other side
Thanks for the videos! Do you know if you can access the pcv lower hose - (going to the manifold) by removing the wheel (and molding behind it) on the driver side? I can’t seem to unclip the hose from on top of the engine. It is a 2011 BMW X5 50i. Thanks so much! Julian
Hi, could you tell me how you removed it?
Any updates on the lower hoses and the best way to access them and replace them? It is so dam hard to get down to where they connect to the top of the oil pan.
Hi Francisco
Yo tengo una BMW X5 2013 y ya le cambié la válvula pvc la que va en la tapa de las punterías debido que se presentaba un ruido más bien un Zumbido como un silbido pero aún se presenta el mismo problema le podrás orientar oh mandarme una información adicional agradecería la retroalimentación soy fanatico de bmw y me gusta mucho el desempeño pero esta falla para mi es nueva
is the lower bolt @4:57 difficult to get to?
Do you have the website of where I can buy these ?
wondering whether you have ever done the PVC valves on an X5m E70?
How do we know its bad ? Oil in it ?
Is this same part for 2013 s63 x6m?
Don't pry the pipes out of the valve covers. They must be rotated towards the rear of the car about 30deg and extracted without prying. Otherwise you will break the plastic tabs and pieces will fall into the camshaft chamber. Not a huge deal, but a finer point.
You are completely correct, I enjoy the videos he creates but this step is critical - I hope people see your comment and get it right.
👍👍👍
Is this dsame for a 2010 bmw 750li
Do you have a shop need some work on my BMW
What are those seals down inside that he was talking about? I wanna do them as well on my 550i but don’t know what they are called
Oh yup I’m an idiot, commented too early. Thank you good sir
I just changed those tubes out last month on my wife’s 2015 750 li. Cost me $400. And that’s a Engineer defect because the plastic shatters after a while because of the heat.
Yes, that plastic is not very good. It has limited flexibility and that doesn't help too.
I.E. Euros have you ever changed out a heads-up display on a 750 li?
Yes, I have.
What is going on with yours?
I.E. Euros mine is not working and I need to replace it, but idk how. I’ve heard it’s a pain because the dash has to be taken apart.
@@dmarco5396
Have you check you fuses?
Is this a tu?
What should I do if the clips on the hose at 5:12 are already broken and have been held together by zip-ties? I looked at mine and that’s what the last person to do this did to hold them together
What did you end up doing here? I broke a clip on that same line.
Mine ended up being fine held by zipties and then I sold my car about 9 months ago. Replacing them doesn’t seem too hard if you have the tools and the time
Would a cracked / broken PCV valve line cause a smell to enter the interior compartment when accelerating hard ?
Exhaust smell? I just replaced my turbo to downpipe seals ($25ea) yesterday, that got rid of my smell, but I did do some work with the downpipes and they are one-time-use seals so skipping their replacement led to me inhaling exhaust fumes inside the car until I replaced them
@@invincibearofficial did u get that smell when accelerating hard?
Can you tell if they were clogged or not? What was the reason for changing them? excessive oil consumption?
They break usually.
The little valve gets stuck sometimes.
I.E. Euros hi after changing them both how long should it take the car to stop smoking?
Its a damn shame BMW would engineer the PVC parts out of that brittle plastic that only last a few years because of the heat. Anyone know of better after market parts that won’t crack
I just subscribed to your channel. I have the same car. I recently started having problems & check engine light. First one was Dmtl fuel pump leak. After driving for 2 days. I did a burnout fresh tires I got then after it went into limp mode & start to show drive train malfunction in the engine. I drove it for a little to park it and start smoking from the engine but the car wasn’t overheating. Put the computer on it the error codes were running a code saying running lean & all cylinders misfire. It starts back up without a issue but it goes back into limp mode & sometimes shut off on its own. However I noticed a air seeping sound from the engine when it’s being rev. Please can someone help me find out what could be the issue here
I have had my Xdrive50i n63 Xdrive50i in bmw for 6+ months . Tryin to eliminate the issue too .
So much has been replaced -
- first it was the injectors, $6000
- map sensor & throttle body
PCV valve & hoses replaced
Then more hoses
- now it’s the intake manifold that has pin size holes - they want $1600 to fix 1 (think left side )
@@stopcorruptioninozqoa2030 Same vehicle same issues, they never stop. If I had BMW fix the issues I'd be broke.
Yet another VICTIM to BMW's intentional bad design right here folks. I had serious misfiring, loss of power, and thicker smoke coming from my exhaust. Turned out my PCV breather hose was broken in two. I believe BMW engineer their parts to last the duration of its original warranties...then they begin to fail, keeping owners spending money on their parts and repairs. I ordered new hoses for both banks, but it was going to be about a week before I would be able to pick them up. So what I did in the mean while was, I went to Lowes and bought a 1/2" × 2' copper tube; a role of heater hose; and 2 hose clamps. I removed the crinkled part of the hose COMPLETELY. Before doing so, I measured the length of the crinkled section and cut a portion of the heater hose the same length. I then cut the copper tubing around 1 1/2" shorter than the heater hose. I then lubed the copper tubing with lithium grease and pushed the copper tube into the heater hose to where it was centered. I then loosely slid the hose clamps onto the hose and then attached the hose onto the two end sections of the PCV hose...then tightened the clamps at each end. The purpose of the copper tubing is to prevent the heater hose from becoming soft from heat and caving in due to the vacuum. THIS WORKED GREAT!!! As a matter of fact, I TRULY believe it's better than the OE. I plan to not use the hoses I purchased unless I HAVE TO. But with this fix, I don't see why I will. So I'll just hold onto them. I don't see why BMW couldn't do this to begin with.
Exactly
Well said
I have the same problem .
But with major oil consumption.
And a bad smell inside the car like rotten eggs well maybe burning oil 🤷🏾♂️.
Everyone Is saying bad valve seals or bad or broken piston or piston ring .
Bmw changed valve seals 50k miles before. So I’m saying does this mean every 50k miles I need to change seals 🤦🏾♂️.
The only reason I can’t figure out my problem is because bmw want to charge $1800 to diagnose , talking about leak down and compression Test.
I brought my car to a one guy shop who claim he was so competent in fixing bmw’s…this joker said to me. He put a camera in my engine and there was whole lot of oil in the engine and he don’t have the shop to do the work …
And charged $125 .
NO SHIT Sherlock--- who wouldn’t guess there was oil in the engine . Where the fuck is the diagnosis . Like u know
The cause of the problem .? 🤦🏾♂️
I tried to harass bmw about why the fuck is they trying to charge me $1800 to tell me what’s wrong with my car ,when a diagnosis is $150.
If it’s this compression and leak down bullshit costing so much. Then leave that out and go to the top list of potential issues.
Because what if my problem is a $1000 fix.
I just spent close to 3 grand for what .? What do people fart and money come out.?
So They refused to back down even after i called corporate.
They intentionally let every warranty run out on me. Because my car was in the shop before warranty ran out .
I had brought it in for diag when they said to me it would cost $1800 to go further
I’m just stuck with a car that is parked in my yard, I’m still paying the loan & insurance for and I can’t figure out what the fuck is it’s damn problem.!
Now I came across these videos and starting to think maybe my problem is one of these pcv valve things.
That would be such a blessing ,
That I don’t have to think about big money cracking open engine fixes .
I pray so hard 🙏
Is this PCV valve help
To fix the white smoke 💨
Yes, that could be a cause
I have a 2011 bmw x5 xdrive50i twin turbo E70 and in having a misfire could it be caused by the pcv valve . I changed all the spark plugs all the ignition coils and 2 new injectors because I was getting a code on cylinder 4 and 8 misfire but since I changed everything I am still getting the same codes 4 and 8 P0304 P0308
Probably you have carbon in the intake valves. Buy a intake valve cleaner to add it with the engine running , One or two if it needed. Clean the codes and start the engine
@@IEEuros thank you for replying i will do that im going to go ahead and replace the pcv valves i saw that they also cause a misfire .good job on the video.
I.E. Euros My issue right now and I think I have a bad RFM module :/. Fucking bmw’s...
@@IEEuros how do I clean the intake valves do you have a video on how to do it
The update I replaced the 2 pcv valves and it still doing the same I get the same misfire code
Same replaced throttle body. & map sensor & PVC HOSES & valves - now they say it’s the intake manifold needs replacement
For PCv valve
hello , i have n63tu engine rebuild it 15k km ago and it started smoking , on cold it has missfires when it warms up missfires goes away, could it be pcv valves cloged up ?
Yes, that could be the cause.
Would a broken pcv valve possibly cause rodknock?
no buddy sorry. you spun a bearing. Thats what happens when you buy a N63. and then proceed to run it low on oil. :)
I just went through this same process. Engine now runs smooth with no codes. However, i now have excessive vacume in the crankcase. The CCV hoses i pulled out came out in pieces so they were obviously cracked. Now that it is sealed i have so much vacume that it is sucking in air from the rear main seal (i think) and makes a squeeling noise. The oil cap is very difficult to remove. Once removed, the noise goes away. Not sure what to look at next perhaps oil separators?
have you figured this problem out ? really wish i knew the answer
@@jshifty9618 it turned out, after many hours and a lot of $ in parts I didn't need to replace, I had defective CCV hoses from Rein. I installed OEMs and the issue went away instantly.
@@paulsandgren8625 glad it turned out into you favor ! i’m looking to get a 550 also 2011 but i’m scared i’ll be spending more on maintenance then what i originally paid for. the dealership is very legit so that kindof makes me think they won’t sell a shit car but then again i know nothing about cars until i look up what i need to know smh
@@jshifty9618 try to.find out if the car had the timing chain and Valve stem seals service done. I went to my local dealer and the service gal looked it up for me. Those are the 2 main problems with that engine
If you're not comfortable wrenching on your own car and have to worry about the cost of service, then this car is probably not for you.
I changed both stem valve seals on my 07 750Li and still had black smoke only when standing in line in the drive-through. dont know what to do next. The oil level is not dropping at least from what I can see. Any advice?
Did you replace the PCV?
@@IEEuros Yes two of them and I took the vale guide and clean it pretty good. My thing is, I did add two bottles of Foam not at the same time and considering both seals were bad maybe the engine is getting rid of what leaked inside and hope it will stop after a while.
Never replace just PCV valve.
Replace rest of the hoses too.
90% of them are clocked
Why can’t I find the part? What is the part number
It is on the video the part number.
What is the year and model of your bmw
Another question. How hard is it to replace the oil return lines in the front of the car?
13:45