Great video man! Any exhaust you would recommend that flows good and quiet so I can drive around the neighborhood? I know it is kind of impossible to have a high flowing exhaust and at the same time quiet, maybe the regular expansion chamber with the silencer or muffler at the end is what I am thinking. Let me know of one if you can lol!
Yeah the mz65 clone with a 22mm moped silencer. Then use 1 inch inner diameter heater hose and 2 clamps to keep it all together. I just got the cr80 that’s gonna be super loud because it’s from a dirt bike
The V2 has my interest completely peaked!! I'm still waiting to find a video that someone does fully modify one that's so extreme that it sets the standard to the common question asked....... "but why?"
TBH your flow issue with the bofeng would likely be made less severe if your fuel line didn't twist and sit parallel with the ground. (don't get me wrong, I appreciate that your frame style and tank outlet are to blame in this case, not you). IMO the Bofeng was designed with top mounted conversion kit tanks in mind, as I noticed that setting a minimal length line with as much vertical drop as possible (especially near the carb intake for obvious reasons!) alleviated all flow issues and resulted in surprisingly great performance across the entire power band. (especially considering that I'm just running a not yet broken in China Doll unit). I appreciate that because you're running an integrated tank frame, the practicality of trying to achieve a vertical drop fuel line is...well, not that possible, at a glance. You seem to have the rare but enviable issue of having a good enough frame setup that the carb just isn't suited to it. Using a quad carb was a damn smart move, I might have to look into them myself, because I'll admit those bofeng jets are..kinda hilariously oversized, as you say, haha.
If you can't weld or don't have a welder. You can still make a nice all aluminum carb. intake, using propane/Mapp gas torch, clean stainless steel wire prep brush & those alumni-weld rods. That can weld small aluminum pieces together. Harbor ⚓ Freight sells em or you can order em online. If you can't get the hang of welding with them to make an air tight seal. You only have to weld it good enough to bond together. Then use JB weld to fill in the gaps & make it air tight.
@@keeganhache6667 Good Deal & good video. Some mineralli videos would be nice. At first I wanted to do a mineralli but now want a 4 stroke instead. I noticed many places stopped selling the 79cc 4 stroke kits. I did see a 100cc 4 stroke kit for $290 that looked decent (I think?) only 3.5hp but with upgrades can easily get 6 -9-12 hp. Or a 125cc pit bike engine with semi auto gearbox for similar price. My next build I wanna do a diy Phatmoto style bike with stronger steel frame. That's reliable, can climb hills & cruise along safely at 40mph for miles without overheating.
Big no it’s not well matched to that engine a g2 reed with a vm18 or a pz20 would do much better better yet park that with a mz65 pipe or a mx pipe and some light port work, 36tooth sprocket boom! Fast bike sometimes it’s simple not to mention tuning goes a long way
is a 62 jet on a 80cc with hp carb and a expansion pipe… too lean? if I got to a 65-70 is chugs on the top of throttle does that mean it’s running to rich or 4 stroking ?
Glad you like the vids. My Minarelli had to be honed out due to damage from a cheap piston. Going to see if I can hone it out enough to support a 47.6mm stage 6 Nikosil piston. Let's keep in touch and maybe make an action vid before it gets to cold. @@keeganhache6667
Best jeting is you have to look at the spark plug needs to be on a light brownish color for better performance. The samler the carb the better for low and meed power.
IV tried running a filter and it kills the power so bad . I'll take the chance of scratching the cylinder and stuff there cheap to replace and for me it's worth the extra power but I'm normally on clean pavement. But sometimes on dirt roads but I also put a half of a license plate on the seat tube to block the stuff getting kicked up from the tire works great in the rain doesn't suck up water and mix with the oil in the crankcase now
Like I said some people can get away with no running it and on something you don’t really care about sure it’s okay but on a engine with so much time into not worth getting dirt inside. Fenders to help to keep sole debris out
I just asked questions in a group past two days on all this..but nobody told me why I'm getting so much fuel blowing back into the air cleaner . I'm running a HP with a 65 jet. And I think I have a air leak on manifold. I'm redoing the surfaces so they mate better.
You need to drill the whole 1 mm the case valum doesn’t have that much suction It will rev extremely fast but it will idle on certain bills I built 4 yd100 70 cc Zuma and a Nine port euro cylinder that cylinder got some fucking peep I do not recommend Jack shaft it lifts up every gear
@@keeganhache6667 no I'm not talking about seizing unless that's what it's called but it doesn't lock up it just dies for a second and starts back up at a lower rpm.
@@keeganhache6667well months later and I did the total opposite I bought a Athena Minarelli and it wasn’t cheap, so with that being said can you tell me what cdi and carb to use?
Your changing to 5mm size jets is brilliant. Yes it works. Thank You.
@@larrylclappjr yup it works great pilot jets are harder to find for these
Glad to see you post again, thought maybe High School preparation was taking all your time and money 😅!
No thats easy prep lol
Great video man! Any exhaust you would recommend that flows good and quiet so I can drive around the neighborhood? I know it is kind of impossible to have a high flowing exhaust and at the same time quiet, maybe the regular expansion chamber with the silencer or muffler at the end is what I am thinking. Let me know of one if you can lol!
Yeah the mz65 clone with a 22mm moped silencer. Then use 1 inch inner diameter heater hose and 2 clamps to keep it all together. I just got the cr80 that’s gonna be super loud because it’s from a dirt bike
@@keeganhache6667 Alright cool, Thanks man! Ignore that hater in the comments lol.
Good info and well presented. Answered most questions on these carbs
Appreciate it
The V2 has my interest completely peaked!! I'm still waiting to find a video that someone does fully modify one that's so extreme that it sets the standard to the common question asked....... "but why?"
V2 what? Phantom or bt100/ yd100 you gotta be more in depth
TBH your flow issue with the bofeng would likely be made less severe if your fuel line didn't twist and sit parallel with the ground. (don't get me wrong, I appreciate that your frame style and tank outlet are to blame in this case, not you).
IMO the Bofeng was designed with top mounted conversion kit tanks in mind, as I noticed that setting a minimal length line with as much vertical drop as possible (especially near the carb intake for obvious reasons!) alleviated all flow issues and resulted in surprisingly great performance across the entire power band. (especially considering that I'm just running a not yet broken in China Doll unit).
I appreciate that because you're running an integrated tank frame, the practicality of trying to achieve a vertical drop fuel line is...well, not that possible, at a glance. You seem to have the rare but enviable issue of having a good enough frame setup that the carb just isn't suited to it. Using a quad carb was a damn smart move, I might have to look into them myself, because I'll admit those bofeng jets are..kinda hilariously oversized, as you say, haha.
If you can't weld or don't have a welder. You can still make a nice all aluminum carb. intake, using propane/Mapp gas torch, clean stainless steel wire prep brush & those alumni-weld rods. That can weld small aluminum pieces together.
Harbor ⚓ Freight sells em or you can order em online.
If you can't get the hang of welding with them to make an air tight seal. You only have to weld it good enough to bond together. Then use JB weld to fill in the gaps & make it air tight.
Right on that’s my first time welding lol no pin holes I shined a flashlight and saw none
@@keeganhache6667 Good Deal & good video. Some mineralli videos would be nice. At first I wanted to do a mineralli but now want a 4 stroke instead.
I noticed many places stopped selling the 79cc 4 stroke kits. I did see a 100cc 4 stroke kit for $290 that looked decent (I think?) only 3.5hp but with upgrades can easily get 6 -9-12 hp. Or a 125cc pit bike engine with semi auto gearbox for similar price. My next build I wanna do a diy Phatmoto style bike with stronger steel frame. That's reliable, can climb hills & cruise along safely at 40mph for miles without overheating.
Thanks for the video 📹 great information 👍 😀. You the man!
Yessir you have been making awesome videos too!
@keeganhache6667 thank you so much! It's a great hobby and I enjoy the community 😊. Keep them coming. I'm always learning something new!
opinion on the Zeda 80cc performance kit with the dio reed valve and the oko shabang?
Big no it’s not well matched to that engine a g2 reed with a vm18 or a pz20 would do much better better yet park that with a mz65 pipe or a mx pipe and some light port work, 36tooth sprocket boom! Fast bike sometimes it’s simple not to mention tuning goes a long way
Thank you!!!!!!@@keeganhache6667
is a 62 jet on a 80cc with hp carb and a expansion pipe… too lean?
if I got to a 65-70 is chugs on the top of throttle does that mean it’s running to rich or 4 stroking ?
Hey bud great informational vid. Where was this vid when I had my huge OKO carb on my china doll? And going nowhere quick or should I say slow...
I saw your videos the bikes go fast my man you got any vertical Minnarelli top ends kicking around?
Glad you like the vids. My Minarelli had to be honed out due to damage from a cheap piston. Going to see if I can hone it out enough to support a 47.6mm stage 6 Nikosil piston. Let's keep in touch and maybe make an action vid before it gets to cold. @@keeganhache6667
@@jmrides777 yeah man hit me up on Facebook messenger
Any plans to fabricate modifications to bikeberry's new V2 100cc iron sleved engine?
Nope
Very informative. Thanks !!
Thanks
Best jeting is you have to look at the spark plug needs to be on a light brownish color for better performance. The samler the carb the better for low and meed power.
IV tried running a filter and it kills the power so bad . I'll take the chance of scratching the cylinder and stuff there cheap to replace and for me it's worth the extra power but I'm normally on clean pavement. But sometimes on dirt roads but I also put a half of a license plate on the seat tube to block the stuff getting kicked up from the tire works great in the rain doesn't suck up water and mix with the oil in the crankcase now
Like I said some people can get away with no running it and on something you don’t really care about sure it’s okay but on a engine with so much time into not worth getting dirt inside. Fenders to help to keep sole debris out
Listen this guy he hnow what he talking about congrast and you said nice advice
I just asked questions in a group past two days on all this..but nobody told me why I'm getting so much fuel blowing back into the air cleaner . I'm running a HP with a 65 jet. And I think I have a air leak on manifold. I'm redoing the surfaces so they mate better.
Shouldn’t really have to do with a air leak sounds like you have a stock piston port setup and a little amont is very normal
@@keeganhache6667 yeah it's all stock except carb and aluminum head and exhaust. Just gonna spray out filter with carb cleaner. Thanks for answering.
KEEGAN. going to eat pizza and watch this video.
Yes man gotta be eating while watching UA-cam videos it’s a given
Nice work bro
Thanks little evil ride safe
Thanks Keegan
No problem bro
I installed the cnc intake and have noticed a big drop in speed and power. What are your thoughts on this?
Cool vid bro💯
Thanks boss 💪
Which part of Nova Scotia you in bud? I'm in New Glasgow?
Bridgewater
i have a 69cc skyhawk build. upgraded cdi, compression cnc head, big boost chamber exhaust, etc. do you think it could handle the PWK21?
Try a pz19
Nice viddeo and the jet people need is depend the altitude you city
Thou shall not hold the Gate Shut , Horizontal sounds Nice, Set them Free 👽👍🏻✨
Lol true words brother I hate guys who hate keep and don’t help others
The guys that say run no air filter are the same one that lick windows 😂
They’re spare parts bud
Nice 👍🏾 job
Thanks
Do you run rag joint sprocket on the minarelli??
No the wheel has a built in hub for sprocket
@@keeganhache6667 ohh thats a gemini?
@@damnthiccassboye7138 just a bbr rim
With my bofeng card n how I'm ported I run a 75 may check how 80 runs
Nice video
It’s a good carb for the case reed
Thanks bud
You need to drill the whole 1 mm the case valum doesn’t have that much suction It will rev extremely fast but it will idle on certain bills I built 4 yd100 70 cc Zuma and a Nine port euro cylinder that cylinder got some fucking peep I do not recommend Jack shaft it lifts up every gear
I can never find a 32mm boot or intake manafold
What do you mean lean out. Does that mean it died at top end
Mine has never cold seized but some guys use really small carbs on minnarelli builds and seize the top end
@@keeganhache6667 no I'm not talking about seizing unless that's what it's called but it doesn't lock up it just dies for a second and starts back up at a lower rpm.
go to two stroke stuffing haha his videos are worth watching... a lean mix means more air than fuel@@joshuamoon8442
I fixed that HP carb I just started drilling holes
The thing i hate about this engine is you cant find an exhaust without welding it and i cant weld....
Well then your probably not experienced yet to build one they are very picky about tuning
@@keeganhache6667well months later and I did the total opposite I bought a Athena Minarelli and it wasn’t cheap, so with that being said can you tell me what cdi and carb to use?
hellow i am brazilian