Back in the day we used to have to pump the oil on to the bearings with a hydraulic type pump system ! I used to print on a huge 6 color hidelburg printing press built in the 30,s or 40,s and we had to hand pump the oil to all the bearings and it's still being used lol where there's a will there's a way to make it work !
Isn’t that a green nitrile o-ring on the piston? That would explain why the vacuum in the cylinder was maintained for so long. Ring gaps would’ve lost the pressure in a couple seconds.
Why not vertical like everyone does it? We want to contain 100 bar and you even have the wrong orientation on the main bearings? Going for a flat-2 in the end?? Those thin bolts may just rip off.
for precidse parts you need machining tools, however it is possible to make an engine using your hands, it just won't be as powerfull and could have small leaks or other problems
Sounds like it will have enough compression!
Because it’s sealed with a nitrile o-ring.
No lube to crank and ring how can it last? Good time not long time.
Back in the day we used to have to pump the oil on to the bearings with a hydraulic type pump system ! I used to print on a huge 6 color hidelburg printing press built in the 30,s or 40,s and we had to hand pump the oil to all the bearings and it's still being used lol where there's a will there's a way to make it work !
Isn’t that a green nitrile o-ring on the piston? That would explain why the vacuum in the cylinder was maintained for so long. Ring gaps would’ve lost the pressure in a couple seconds.
I thought the same. It really looks like it.
Altough it has good compression it would probably melt when it would start
Looks like HNBR o ring should be fine for a but
Good compression. But its sealed with a rubber ring. It would melt if you started the engine
Good job !
Is that a Honda GX50 crankshaft assembly? Or maybe from a Stihl chainsaw?
It has very good compression, good job!
Compression is very good!
В чем прикол этой якобы многообещающей музыки😂
The music sounds like "Delirium"
厉害👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻
good job
Why not vertical like everyone does it? We want to contain 100 bar and you even have the wrong orientation on the main bearings? Going for a flat-2 in the end?? Those thin bolts may just rip off.
Nice job, did you use any machining tools or completely diy with ready to use components
for precidse parts you need machining tools, however it is possible to make an engine using your hands, it just won't be as powerfull and could have small leaks or other problems
Это какая-то проблема.... Резиновые поршневые кольца😮
how do you lubricate it?
Your mum squats over it.
your turning it a deferent way,clockwise not counter clockwise, turn it clock wise
That's awesome how do u find spark timing
he will probably use a contact breaker
After all the other more important parts are done.
how can i make one?
Bel lavoro! Vuoi realizzare un motore Stirling?
😱I understand your message perfectly, be careful to make it work sin combustible solo con autocompresion
Parabéns amigo
❤❤❤❤❤❤❤❤❤❤
Компрессия лвл99999999😮
Just get a dirt bike
that is not compresion it is depresion
Vacuum, you mean?
І що???
NO cooling blades.
What? That’s what you noticed missing? Not the valvetrain, cam, oiling, intake, exhaust, ignition? Fan blades?!? 😂
This would be a 2 stroke
ICPE. INTAKE, COMPRESION, Etc Etc...unfinished but cool little piece of of machinery.
how can i make one?