Splitting the Engine : Yamaha TTR125 Part Four
Вставка
- Опубліковано 22 сер 2024
- I get the engine completely apart and decide what parts to change.
Tom's Tinkering and Adventures would like to thank you for joining me in my adventures! Comment, Subscribe, and most of all, be inspired to live your own adventure when the time is right!
HELP SUPPORT THIS CHANNEL:
I hope you enjoy the material that I offer, if you would like to support my channel there is a link below. Take note that it actually goes to my wife's account! She supports me in my adventures. Bless that woman!
DONATIONS: www.paypal.me/...
FOLLOW ME!
If I'm on a motorcycle adventure, I take my Spot-X GPS tracker with me. It allows my family and friends to keep up on my progress and see where I'm at. The link below will be updated every time I get ready to go on a trip.
share.findmesp...
Thank you for making this series of videos! I just picked up a ttr 125 that has a grinding noise in the case. It will be a great project to tackle with my kids
I wish you good luck with your rebuild, should be a good experience to share with your family.
Good stuff. Luv the Don Henley :). Hope you and family have a blessed Christmas!
Gregor Miller gracias, Merry Christmas to you and yours!
Solid Videos thank you for sharing
greeneman99710 hopefully it helps you work on your bike.
I'm having the same issue getting the crank apart, where you paused the camera and rejoined the video, and it was apart. What is holding it after you get it about 1/2 to 3/4 inches apart and how did you get past it?
A tip for them case screws would be to use an impact driver. I have yet to strip a screw, removing or tightening.
And ensure you are using a JIS bit!
Ya always use the proper bit lol but I do like how you point out the difference in the 2 types.
Tom, Just bought the flywheel puller you recommended in the video from Harbor Freight. Can you confirm you put a socket over the bolt on the shaft for the puller to push on? What size socket did you use if you used one. Thanks!
I don’t remember if I did, I guess if I show it on the video then I did! I cannot remember what size it would be....
Hi Tom,
I need to remove the gears on the input shaft to replace the second pinion gear but the first gear won't slide off easily there isn't any cir-clips holding it on to my knowledge, do I just need to give it a pull with a gear puller or am I missing something? Don't really want to go yanking on it if thats not the way to do it.
Matthew Hughes I’m sorry, don’t remember. Some of the gears do have clips. I am always hesitant to start using force but sometimes you have to. Let me know how it turns out.
@@TomsTinkeringandAdventures I just heated it up a little and got a bearing puller on it with an impact and it slowly pulled off. Not sure how it's going to go back on at the moment though, maybe try sweating it back on like a bearing
Matthew Hughes maybe put the gear in the oven at 200 degrees or so for a while? Done that with motorcycle engine cases when installing main bearings...don’t tell my wife!
Hey Tom, Got my second wind after dinner. Went back to the garage to split the engine and ended up stripping the shift star bolt. Can you confirm that it has to be removed to split the engine? You sounded like you were not 100% certain in your video. Thanks!
I’m sure the manual says it has to come off, but you might be able to try to keep all of the transmission in the right side case when you split it. Worst case, you have to figure out how to get the stripped bolt out.
@@TomsTinkeringandAdventures Thanks. Yea, stripped bolts really hurt moral! I will let you know what I find inside. Again, great videos!
And do I need to buy new gaskets once I open it or can I use the same ones and put them back after I open it
Always order new gaskets, best to replace them.
Do I have to tear both sides open to get to the crankshaft because mine is sized and I bought a new one
Yes, both sides will need to be opened up and parts removed in order to get the crankshaft removed
Just got one tore down with a bad rod bearing, how do I split the crank to replace?
You have to bring it to a machine shop, or buy a new crank with a rod.
Hey Tom I have a ttr 125 with the kick start jamming any idea
Pull the side cover, make sure everything is set up correctly with the kick start gear/spring/etc. They are a bit tricky to get right.
Hi tom when I pulled my fly wheel off there is no idler gear behind it I have an 05 ttr125 I believe… what is the year of the one in this vid!
I don’t remember the year. Is yours electric start? If not, it wouldn’t have the idler gear
@@TomsTinkeringandAdventures thank you so much that’s what I was thinking just not sure .. and then the bigger gear behind your flywheel? Would not have the either?
@@TomsTinkeringandAdventures thanks a lot man
@@damianlakes3463 yes, without electric start it wouldn’t have that either. Hope your repairs go well.
@@TomsTinkeringandAdventures with me going off your videos it should no problem 😌🙏 thanks again buddy . And the response time. Was the best part of it all have a good day sir
does this engine have a crank seal. mine runs lean when hot
Thomas Bryce I don’t remember, but a crank seal on a four stroke won’t affect that. I would look into jetting.