How to Install a Sewage Ejector Pump
Вставка
- Опубліковано 6 бер 2015
- Sewage Pump: amzn.to/3pLCSZ3
Cheaper pump alternative: amzn.to/3h7WzDV
Check Valve: amzn.to/3Hz9oE5
2” PVC Ball Valve: amzn.to/2DdvM69
Tank Alarm: amzn.to/316JIfm
Pump and basin combo kit: amzn.to/2Bm85IJ
Lid w/ seals/grommets: amzn.to/3nH2qWy
Milwaukee Drill/Driver set: amzn.to/3auep1t
DeWalt Drill/Driver set: amzn.to/2PVXmM3
DeWalt Circular saw: amzn.to/3kZzmpv
The BEST Screwdriver: amzn.to/3qGdraD
The LAST pair of pliers you’ll ever buy that the PROS use: amzn.to/3aYacDk
AWESOME wrenches: amzn.to/3lioLq3
The BEST Hammer: amzn.to/3lUKFjw
Drill bit set/index: amzn.to/3kSj1Tu
In this video, I show how to plumb and install a sewage ejector pump.
Please like, comment, and subscribe. I'm also happy to answer any questions you may have regarding your repair or installation.
Check out my channel for other repair videos. - Навчання та стиль
A few things I would do differently:
1. install check valve & valve higher, gives more room when servicing pump (nothing better than hitting your head on a "crappy" pipe)
2. cut vent pipe at same height as check valve, and install a rubber coupling w/ hose clamps (for servicing)
3. ALWAYS use pressure PVC fittings on pump discharges, not standard DWV fittings
4. Use Zoeller or Gould pumps (I'm not a fan of the loose floats)
Side note: I recommend silent check valves. Regardless, (I don't know if you mentioned it) ALWAYS use check valves with rubber couplings, never the compression type with the big plastic nuts...
This is probably the best instructional video I've EVER seen on UA-cam. Right to the point...no horrible music bed... good solid steady video work without a bunch of zooming and effects....AND a great east coast accent, very refreshing here in the land of stoner surfers and valley girls.
Brett Weathersbee Thanks for the compliments and for taking the time to comment.
agree with you. the best tutorial video on the subject.
As I stated in my comment the likely reason for down votes is no weep hole which will cause future problems of air lock. I've seen pumps burn up prematurely because of this and have made quite a lot of money on people doing these things themselves and not reading the instructions or watching videos where this isn't mentioned. It seems very simple to install a pump and it really is however a small mistake can be costly. If you are going to do this read the instructions I'm pretty sure this is covered in them.
@@my2centz196 What are weep holes and air lock?
@@katie2920 if air gets trapped inside the pump it will continue to run non stop until the motor burns up. The weep hole allows the air a place to escape. A lot of pumps have them already drilled in the pump itself however they can get clogged up. It can get air locked even if the tank is full and after the pump has been working for years by a cyclone kinda like a tub it just sucks the air down. A check valve is installed so the pump doesn't continue to pump the same liquids over and over as the fall back down however without a weep hole when air gets trapped into the pump it can't escape.
7 yrs later this video keeps on giving. Thanks Zim!
💪🏻💪🏻…still going strong
Who would thumbs down this video?? That's moronic. It took a lot of effort time and patience to make this video and is EXTREMELY helpful. This guy is a perfectionist that does incredibly detailed high quality work. Thank you so much for your efforts! I appreciate any help I can get from contributors on the web. THANK YOU!!!
Eric Bjarnason Thanks for the comment, appreciate it. Haters are just trolls on here. I don't let them get to me.
Thumbs down must be from those who don't want you to be able to do it yourself thanks to helpful souls like Zim
A hater..lol.. because he is damn detailed
Around here that kind of pit is illegal. The pit he is using is made for gray water or what we call a sump pit. A sewage ejector pit is made specifically for sewage . It’s usually wider at the bottom and has to be manufactured with an air tight seal.
On top of that this is a sewerage pump, an ejector is pneumatic
Oh my gosh, thank you so much! Your trick about separating the two plugs and plugging in the pump without the switch was a lifesaver. I was looking at the pump and the pad and my shop vac thinking that vacuum was going in the garbage after this. I’m so grateful for that hack.
Glad it helped!
Great job on this, man. Nice to see an instructional vid on here that's very thorough, informative, and to the point.
Going through this house we bought and fixing all the sloppy, failing "work" the previous owner did, (the plumbing & electrical are trades I have the least experience in) and now this issue came up...of course. And based off your solid info here, he didn't do that job even close to correct, and the damn lid wasn't even gasketed or fastened on!! Infuriating stuff! Not looking forward to this job, but you helped answer the small detail questions I had...so thank you!!!
Awesome video. Building a new home and engineers said we need one of these pumps; architect suggested a closet for it, and we wondered why. This video helped us picture the design. Thank you for posting.
I'm currently at the end-stage of building a house with a builder. 16 months of construction has been awful. I'm finally taking over and doing things myself. This helps so much. Thanks, man!
This is one of the best, most informative, DIY videos I have seen. I feel like I can absolutely do this job PROPERLY. Thanks for putting this together!
The best install video on YT. Straight to the point in formative. Filmed well. Excellent. Thank you!!!!
he even cut out the baby when it started crying at the ~7 min mark, lol
Thanks for the video. My pump has a VENT line all the way to the basin bottom submerged in water 90% of the time.
Your 3" max below the cover was the best information!!
Always nice to see a helpful UA-cam video!
You provided all of the information in a clear, concise, and chronological manner. Your explanations of the components, included "Where they are to be installed" ... "Why they need to be installed" ... "How they are correctly installed" ... and ... "How they operate."
The video also included helpful suggestions, wherever possible.
Your presentation takes the average DIY homeowner, from "Confused" to "Confident" in just 16 minutes.
Great job!
Much appreciated.
Thanks for taking the time to comment. Glad the video was helpful and informative.
Been watching YT vids since '05 and have left maybe five comments in that time. You, sir, did an amazing job here: great detail yet concise (tell us all we need to know in the fewest words needed), and you anticipate questions one might ask and answer them, then "tips" are gold. Six year old video but you've got another sub! Thank you!
Thanks a lot man, I appreciate that!
thanks man. Your suggestion to use just the pump plug worked for me, saving me a call to a plumber. I appreciate you taking the time to put the video together.
+Christopher Anderson Great, glad the video helped.
Thanks. It helped me understand a lot about what at pain it is to add a shower to an already finished 1/2 bath in the basement. A lot of stuff that could go wrong doing this on a house that was built in 1979. Its epoxied all over the top and also sealed with silicone.
This is GREAT!!! Detailed, informative, even decent camera work and narration. This video saved me a lot of money! Thank you so much.
It's 2020 and I just came across this video. Easily the best one on UA-cam for this topic. Thanks!
I really want to say thank you. Your advice about the float switch and the two plugs really just helped me determine that my pump is fine and to pump out the water and see what is wrong with the float. Thanks!
Same here. Thanks for the video!!!
Great explanation. Quick and to the point. My ejector stopped working and I was in a panic. In the beginning of the video you explained what the 2 plugs were. I unplugged and used the direct power line to empty the pit, plugged it all back in and it is now working great. Thank you!
Fantastic video... thanks much! It's clean, straight-forwared, direct to the point, and demos a high quality installation. The extras like the gasket inside the bolts, the anti-seize on bolts, very practical point about the pipe bends, (2x 45's instead of a 90, ball-flap valve... We don't often get clear concise practical videos without having to wade through all the music and production crap. This is awesome... very well done!
Thank you! I try to keep my videos simple and detail oriented. I’m not trying to entertain in them like others. It’s a how to video, probably best to stay with showing how to do things...lol
Absolutely perfect video. This guy is both a pro who knows all the ins and outs, and ALSO remembers the first one he installed because he answered all the questions a first-timer would have. Many thanks for making this video.
One thing he didn't mention is a weep hole. I've said this a few times so far but if you install one read the instructions! Make sure to drill a 3/8" hole around 6"-8" up the discharge line. Usually somewhere around the waterline. Edit if you do not do this you risk expensive future problems including prematurely burning out your pump!
Great instructions, no music in the background.
You get 5 ✋✋✋✋✋
Thank you so much for this.
Just a brief crying baby.
Thank you so much! It's 11:30 p.m. on a weekend and I thought I had a real plumbing emergency. The basement toilet stopped flushing and there was water mixed with other "juices" coming from the pit. As with all household emergencies, of course I went straight to UA-cam. When you mentioned that there may be separate plugs for the float switch and the pump, I immediately looked for that and found out that the pump still works and the switch is the issue. I think you may have saved me a few bucks. I still need to open everything up and check the float, but that's nothing. My pump is about 10 years old, so maybe I'll have to look into replacement, but at least your video helped me for now. But after viewing your video, I think replacing it myself may be possible. Thanks again!
Dude! You saved me a ton of money and time within the first 3 minutes of this video. Found out my pump still works, just need to see why the float valve is not functioning. Almost called a plumber, but decided to get dirty and tackle it myself. Now I can spend the extra money I would have spent on a plumber, on something for my motorcycle or a new gun...LOL!
LOL, I love it man! Enjoy and thanks for the comment!!
Perfect! .. My pump quit this weekend and this video made it look easy for sure. I'm going to replace the pump myself and save about $350. ... Nice work!
fivefootsixtriumph Thanks, glad the video helped.
I just had HEP Plumbing in Chattanooga come out and diagnose that my pump was bad and it would be almost $7000 to replace it. So I started watching videos. Saw the tip about the pump plugged into the float valve, so I went downstairs and directly plugged in the pump and the pump worked! So I have a bad or stuck float valve, something I might be able to handle myself. At the very least, I now know how to get that gross tank empty before taking the lid off of the tank. Thank you!!!!
Fantastic video! No point repeating what other are saying below. You are an excellent teacher. Thanks!!
Excellent, informative, easy to understand video done very well. Thank you, it really helped me understand what was going on before I replaced my sewage ejector pump at our cabin. I feel like I owe you a beer!!
Mark Tucker great man, glad to hear the video helped. Thanks for the comment.
Thank you so much for this video. It is amazing, I got a house that has absolutely the same setup and the problem is that it smells sometimes and I have to fix all this by myself.
Actually, the lid of the basin is absolutely disconnected and it is patched with some insulation and I also suspect that the vent pipe is bad too.
So thank you for showing me all the steps. Greatly appreciated.
You're welcome. Get that lid sealed and socked down. It will most certainly solve your problem
Thanks for the bit on the power plugs. I unpluged the double-plug and plugged-in the pump cord and it worked. I found this video informative and well-done. Thanks.
You're welcome. Thanks for the comment!
I am a two-year apprentice I took on a side job replacing a sewer ejector pump in Nassau County Long Island I would love to say you save my life thank you
Love this video, I have a sewage pump in my basement that flows to the septic system. No issues with it so far this video just shows that you can change the pump yourself if needs be without calling a plumber save yourself money 💰
Absolutely! Such an easy job and you can save hundreds doing it yourself. I’ve seen guys charge people over 1200 to change a pump out.
Perfect..no BS.video!! made an easy job fool proof! thanks!
Thanks for the compliment!
The tip about bypassing the float saved me hundreds in a service call.
Many thanks
PERFECT !
I will do this to my basement bathroom . I learn almost everything from your video about "How to Install a Sewage Ejector Pump". VERY helpful video.
thanks a lot.
Glad it helped. Good luck with the job
Hey man congratulations that's the best and explained video I ever seen keep the good job 👍👍👍
Great video! Thanks for uploading this, I saved $2,500. My plumber suggested I change my sewer system with a new one. I saw your video, changed the float switch and the lid and the problem was solved. Total expense $75 only!
That's great!...glad the video helped you save some coin. Thanks for watching!
Haha yea plumbers always want the recipe. ThT 2500 was a deal to haha cash only
Appreciate you taking the time to make this video. New (to me) house with an ejector pump in the basement that is leaking at the inlet. Great video, so I know the mechanics of this to see what my problem really is and if it’s more than just a minor leak. Thank you very much!
Thanks for sharing you knowledge. Amazing human being you are. My best friend was a plumber. He always said “ two heads are better than one! “
Excellent video. I wish working on these was ever this clean and non-gross.
Scary to see this type of installation in a basement. We've had a pump outside our home for 20 years and have witnessed many failure modes. The worst problem is if the float switch fails to start the pump, which often and easily happens, then sewage will overflow the pit and flood the basement with sewage. Our 1st pump was 24 years old before it failed. It was a Goulds. The replacement was a Zoeller and lasted 3 years before its integrated float switch failed.
Its amazing how these systems are not designed to be very reliable yet they consequences are very bad if they fail.
There was no testing to see if the system was working at all. Would be an awful time to find out the pump is defective. Or find out that the float switch is getting hung up on a cable or pipe.
Float switches only last a few years. The way you may find out its failed is when it overflows.
Even if the float switch is still good, toilet paper can weight it down and prevent it from starting the pump.
If or when the pump fails, replacing the pump will be an exciting challenge with all the solvent joined plumbing blocking access to the pit.
Even if its just toilet paper preventing the float or needing to replace the float switch in 2-3 years, its hard to imagine how to do it with all the plumbing solvent joined in place.
- There should be an easier way to remove plumbing attached to the pump, such as having a union on sewage and vent sides.
- There should be an overflow alarm wired in to alert when level gets too high indicating pump or switch failure.
- Mechanical float switches last only a few years best case. Electronic switches are available which are much more reliable. Look at Hydrocheck. Built in float switches are the worst. At least the Everbilt has an external switch so you can replace the switch without having to replace the pump.
I have both lift station on my septic field and basement sewage ejector pump. My experience with Zoeller is that despite their reputation, their pump only last 3 years. Yup, the float switch fails just about in 2 to 3 years. This is really bad design from Zoeller and I've learned this by using them for over 20 years. Do not use Zoeller pumps. You would think the Zoeller would notice this and fix it in their pump but they are not for whatever reason.
As to this basement sewage ejection system goes, there must be a better design. When the pump fails sewage just floods the basement floor. Perhaps have an alarm system in place and design the pump to be placed outside the pit or something....
Excellent instruction
Thank you!
Thx Zim!
Awesome tips ( 45° elbows and bolt anti corrosion treatment). perfect instructions ..thank you
Thanks for taking the time to make a very detailed video. Our new home has this exact pit and we’ve noticed serious sewer gas every time the wife does laundry. Following your instructions we find no seal on lid of any kind. I’ve ordered a jackal seal kit and hopefully this will solve our problem. Thanks!
Good Video. I'm on my way to finishing my basement. I have had mutiple contractor give me a 5K quote to install a grinder pump. Just bought one from Amazon and doing it my self. Saving me $4000.
That Tech Guy Excellent! Hope the job went well
good video man. I am a plumbing apprentice and trying to learn everything I can.
Journeyman yet?
@@andrew3453 yes
@@ronnienoneyabusiness2844 Glad you made it!!! 💪🏼
@@andrew3453 thanks brother it was God for sure. in spite of myself he still does awesome things
Want to say thanks, flapper was stuck and your video helped educate me and prevent a repair call. Subscribed! -Greg
Very well done. I searched as many videos as I could till I reached yours. I have to replace mine as a first time homeowner. I feel much better doing this now.
Great, glad I could help. It's an easy job if you don't mind getting your hands dirty.
when I do these, I always drill a hole to insert the electrode for a water alarm and seal it with silicone. Just a precautionary measure. I also add a GFI with built in alarm (GFI is code in my area for any sump). So if the GFI gets tripped, it will set off a sound so you wont get a messy surprise.
Drill a hole near the connection point at the base of the PVC where it connects to the pump so that it sprays the float to keep it clean and also drains the I remeaning water under the check valve.
Not on these pumps.
Very good video Zimmsjeep. Finally someone doing a video who knows what they are doing and very informative. Others have responded about vent holes and electrical needs and you nailed it by saying read the instructions from the pump system you are buying, these if followed will allow for a great installation. I just bought an old 1940's house in Missoula Montana and this closet application looks almost exactly as mine will be, and yes the Home Depot Everbilt is fine for all applications, as are other manufacturer such as Zoeller. Really a great video, thank you
Gary Sisk Thanks. Yes everyone quick to assume and point the finger on UA-cam. All good. Glad you found the video helpful!
3:11 this part helps! I'm about to call a plumber. Watched this video and tried the trick you said. It works! It saves me lots of money and without any mess on floor and wall. Thank you again!
Pretty good video but a few key points overlooked. First, discharge line fittings should be rated for pressure. This is code in a lot of areas. Secondly, if you use a check value, a air bleed hole should be created to prevent air lock. Also, make sure the voltage on your circuit matches the pump.
Thanks for the comment. This pump doesn't call for an air bleed hole as the pump itself releases the vacuum. I believe the NEC calls for a dedicated 20 amp circuit for en ejector pump in which case my install has. I wasn't aware of using sch 40 on the pump discharge. Makes sense but then again the pump isn't putting that much pressure into the line. All the installs I've ever seen have used DWV PVC as I have used. Thanks again for the comment.
MIke H professional
@@fixitwithzim What is an air bleed hole?
@@katie2920 is about a 3/16 hole drilled into section of pipe connected to pump maybe about 12” above pump connection to relieve any air in pipe that might cause air lock if pump is running and not pumping this could be the cause fixed several pumps with this simple addition
imagine being a new pump your like yaaaaaa gunna get installed woohoo time to work.. wait wait wait whats that smell sniff sniff oh god nooo noo gurrgleee gurrrgleeee blaahhh pukeee.... no no nooooooo what the hell ahh not again.. 20 years later i giveup
I’ve known nothing about this install but I’m a hands on type guy. This video is fantastic! I won’t be installing this lift pump any time soon but I’m sure with the aid of this video, I will be more confident in doing it myself. Thanks a lot buddy!
Thank you for a highly informative instructional video. My pump has failed. I was afraid to DIY before watching the video but am now reasonably confident that I can do the repair!
Great, glad I could help. Good luck!
Sewage Pump: amzn.to/3pLCSZ3
Cheaper pump alternative: amzn.to/3h7WzDV
Check Valve: amzn.to/3Hz9oE5
2” PVC Ball Valve: amzn.to/2DdvM69
Tank Alarm: amzn.to/316JIfm
Pump and basin combo kit: amzn.to/2Bm85IJ
Lid w/ seals/grommets: amzn.to/3nH2qWy
Milwaukee Drill/Driver set: amzn.to/3auep1t
DeWalt Drill/Driver set: amzn.to/2PVXmM3
DeWalt Circular saw: amzn.to/3kZzmpv
The BEST Screwdriver: amzn.to/3qGdraD
The LAST pair of pliers you’ll ever buy that the PROS use: amzn.to/3aYacDk
AWESOME wrenches: amzn.to/3lioLq3
The BEST Hammer: amzn.to/3lUKFjw
Drill bit set/index: amzn.to/3kSj1Tu
This is exactly what the doctor ordered. Thanks so much for a great description
Thank you. Best video ever. Had issues with my pump not working and learned how to fix it. Saved me tons of money and now have the confidence to tackle this with all the parts and knowledge to deal with all the what ifs
Would of never thought of checking float switch, upon watching I removed the float plug, water immediately sucked up. Cleaned and removed hair and such from float was all it needed. Thank You
Jan Dangora You're welcome...happy to help!
Great video! I didn't know what the two plugs were for and that really helped me out. Saved me a call to the plumber.
Thanks!
Great to hear! Glad the video helped you out.
Well done video. Thanks for putting this together. Several things I didn't think of that you pointed out. Makes the prospect of adding a basement bathroom sound less intimidating.
Chad Portenga It’s actually not that hard a process adding a basement bath. Check out my other video. I go over the entire install of a full basement bathroom
Thanks so much for this! Ours is set up the same way, (though to a septic tank, not a sewer line) and I feel pretty confident I can change out our check point and pump now.
Rachel Brunscheon Yup, easy job once you know the ins and outs of it. Good luck and thanks for watching!
A little trick I learned over the years is to drill a 1/4 " hole in the side of the discharge pipe about 6" blow the cover .... This will prevent the discharge from getting AIR BOUND ..... That problem drove me crazy years ago ....An old timer plumber showed me that trick & never had a problem since ....Great video !!!
Bless you! I did the unplugging and it cleared out the water and now it’s running ! Thank you sooo much
That’s great!! Glad you got it running again 👍🏻
This guy knows his stuff and explains it very well real class act thank u i enjoyed this video
Excellent video - very well done. Like Terry Sutherland I have the same approach to failed systems. When I checked the pump, it worked. The float switch needed replacement [$31.00 at Home Depot] - about 30 minutes from start to finish to remover and replace failed float switch [including clean up]. Thanks for the video suggestion about testing the pump by plugging the power cord directly to the outlet. You saved me hundreds of dollars. Thanks!!
You’re welcome!! Glad you got it fixed on the cheap!
You just saved me a whole lot of aggravation with your explanation regarding the float switch! Thanks for your excellent video!!!
Excellent video. I’m tackling this project this winter. Thanks for your video!
This video was super informative and straight-to-the-point. Thank you 🙏 !
Outstanding video - concise and practical. Thanks for all the "insider" information.
Great video! Took a complicated task and made it simple...huge help, thanks
Sir, I think you created a great video that is down to earth and easy for the everyday joe to understand. Thank you!
One simple note though, remember, two 45s equal a 90 so it is still making a 90 degree turn in terms of resistance to surface. Absolutely no disrespect intended!
Great video!
Thank you. You were very helpful. I think i got lucky. My pump worked for 14 years. But did not have major use. Something else to do today. Add it to the list. Lol. Thanks again great video!
Thanks so much for this step by step video where you really get into the details. I’ve been looking for something like this (and your rough in plumbing video) for a while. Hopefully can start my project soon!
Yes that rough in video was great, just came from there. About to start jack hammering today. 😮
Great job - no nonsense video. My pump burned out today so this really helps to explain my system, thanks.
You're welcome, glad the video helped.
Excellent video. Thanks for taking the time to make it. You've saved me a big plumbing bill.
Great, thanks for the comment!
These are the best videos on the topic by a Longshot! Thanks!
Thank you!
Perfect explanation. Thank you for taking the time.
Nice job. Very clear instructions. I just bought a house and might put a bathroom in the basement. This will help. Thanks.
Best video ive seen yet. Really appreciate it brother!
No questions , thank you !
You are welcome!
This is EXCELLENT...Thank You so much for doing this
I appreciate the video. I was able to troubleshoot a problem, and it was my check valve
I see others agree. One of the best videos of its kind!
Thank you!
You my man save me a LOT of headachessss. Your the beast and for that you gained a new subscriber thank you again.
Wow very detailed information, best how to video I have watched.
Thanks a lot for sharing.
My big take away is the 45 degree elbows as opposed to 90 degree also the shut off valve, I had the check valve however, I never thought about the shut off valve.
Thanks again.
great tips - awesome video. Thanks!! to the point but thorough - which I love.
I'm a school teacher watching your video with my husband. You are a great plumber and teacher!
Thanks, I have a few teachers in my family. Guess I learned a thing or two from them. Glad you found the video helpful.
Excellent video! Very thorough.
Thank you so much for this video. Very informative. Nicely done !
Excellent and much needed video. I am going to be doing this same install soon and I know now how to do it thanks to you. Thank you for taking the time to teach all of us. God bless.
You're welcome. Good luck with your job.
You are an excellent super thorough instructor. By far the best how to vid on UA-cam. I love love love the details u gave on every section of this install. Thank you so much sir. God bless. 🙇
You're welcome, thank you!
Great video! thank you for making a complete, very helpful video. one of the top DIY videos out there!
Thank you for the kind works!
Thank you for this very simple installation video. This was very helpful
Great video! Really appreciate you making this.
Nice work. Thanks for a clear and straightforward video!
You're welcome, thanks for the comment!
Thank you, excellent instructions!
Absolutely fantastic, informative video.
Family member new home (to her) has smell. I looked and saw 2 pumps. A sump pump 4ft down in a caged/wired gravel pit and 30inch deep plastic basin with what appears to be your videoed sewage pump installation.
Head scratcher but your video is helping our research.
FarFromN0thing yeah, that’s an odd install. Anyway hope the video helped solve your problem. Thanks for the comment
Thanks for the video you did a great job with it. My basement office is in a room next to my sewage pump. I've dealt with a smell for the past three years. I hope that your weather-stripping tip will do the trick to better seal the smell. I chalked around the gaskets at both pipes and it didn't remove the smell. I was thinking of adding an inline fan on the vent to hopefully fix but I'll try the weather-stripping first.
Nick Thanks, the weather stripping will solve your problem. Then reseal around the cord, vent, and pump gaskets. Also doesn’t hurt to run a bead around the lid when you get it reinstalled as well.
I just installed this exact same pump. I hope it lasts. Replacing the dead one was no fun! Nice work in your install here. I'd throw a union on that vent pipe, myself, to make future service easier. Thanks for the video!
Thanks for the comment. When the time comes for pump replacement, I can cut the vent and put a no hub coupler on.
+zimsjeep cool. Thanks again for taking the time to make the video!