Ok good video, put on filter now for some reason it gets air locked when it sets for a while..apply air pressure to tank,fires right up,no loop on hose,all down hill run for fuel,
Thank you. I was planning on pulling the studs, but confirming that inner cover had to come off and where the hidden screws were was the ticket I needed. And a good suggestion on adding the inline filter. Kudos.
Thanks for doing this video. My generator was suffering from hard starts and engine surging. The technique to remove the stud worked perfectly. I didn’t remove the air box or the second black cover. I removed the soft pliable rubber duct by pulling out of the air cleaner housing. The studs do pull out. They get hung up on the rear gasket, but once you pull the studs out, the carb will pop right out. A couple of things I discovered are that these little engines are very sensitive to improper spark gap (which is supposed to be .025” and the oil should be topped off or changed regularly. When they run, they run great!
Thanks for the comments. I have learned that if you run 30W oil (not 10W-30 but straight 30W) they do not burn any oil. I use 30W diesel oil from Walmart. If you look on my channel I have a 400 hour review video that I show the oil I use.
Good information. EDIT 2 WEEKS LATER ....Thanks. So i started doing what you suggested, and discovered rather quickly. if you take off the fuel cap, and then the rubber deflector that keeps gas out of the case, The gas tank is NOT ANCHORED BY ANYTHING BUT ECCENTRICS THAT POP INTO THE RAILS. You can take a screwdriver and put it under the tank and just pop it out. This makes doubling the nut unnecessary, and makes cleaning the tank easy.
Your video was dead on ! thanks for the carb stud trick, I left the linkage hooked up, filled the carb over pulled the float bowl, needle seat and just sprayed B12 carb and choke cleaner and blew it out clean. Only trick I would suggest is stuffing a shop rag behind the carb so when and if you drop that nut you don't go crazy.
I hate to go thru all that and not replace the needle and seat inside the bowl so appreciate your breakdown. I was gifted the Wen 2000. It held out ok for a day without power during hurricane Ian. Ran it dry afterwards and ran it once a month since. Always started right up. Last month ran it and it slowed down and sputtered off sounding like it was out of gas and now won't restart and small as it is I'm only good for about 10 pulls lol Can't see the spark from the plug grounded well to the case, that's the only thing that little pillar they got there is good for, to hold the plug onto the case and no sparkay so going swap that out and look for a carb kit. Keep on fixing!
Thaanks for posting this video.. i will be removing my carb in the next day or two. Getting ready for rolling winter blackouts here in Texas this winter.
I have answered this topic before. Yes you are correct there is SUPPOSED TO BE a little white filter that sits in the fuel inlet on the carburetor. This generator did not have one. I have done annual service on over 50 of these units now and it really is hit or miss if they have one or not. Out of the 50 or more I have done I would say less than 20 had those filters. If yours had one then you can count yourself as one of the lucky ones.
Sir thank you for the video I am going to install a filter as preventative maintenance and I will be calling my new generator the harbor freight Nonsense 2000 watt generator
No method is fool proof. I have gas jugs with filters on the pour spout and the tank has a screen. Yet I am still pulling a carb and cleaning a tank. I will say this though, I am far from a casual generator user. I have 5 Generators from 1000w to 6kw. I live off grid, and sometimes you just need AC this far south (near Texas Mexico border) or to charge the solar batteries. This 2kw i picked up used for 300$ a few years ago. Its just big enough to run 8 hours on just over a gallon, charge batteries and keep AC running. So it gets run to death.
I haven't gotten that far yet, but the video I was watching it was IN the carb itself. It's IN the hose barb. I'll probably find out for sure over the weekend.
Yes you are correct there is supposed to be a small white filter that goes into the fuel inlet on the carb. I am not sure why mine didn't have one. Thanks for pointing that out.
I love the video really good idea about the filter and the way you take the studs out thanks for the help
@@gerardobarajas4254 thankyou. I am glad it was useful.
Ok good video, put on filter now for some reason it gets air locked when it sets for a while..apply air pressure to tank,fires right up,no loop on hose,all down hill run for fuel,
@@patrickhall3878 could be the vent in the gas tank cap is blocked?
Thank you. I was planning on pulling the studs, but confirming that inner cover had to come off and where the hidden screws were was the ticket I needed. And a good suggestion on adding the inline filter. Kudos.
Thanks for doing this video. My generator was suffering from hard starts and engine surging. The technique to remove the stud worked perfectly. I didn’t remove the air box or the second black cover. I removed the soft pliable rubber duct by pulling out of the air cleaner housing. The studs do pull out. They get hung up on the rear gasket, but once you pull the studs out, the carb will pop right out.
A couple of things I discovered are that these little engines are very sensitive to improper spark gap (which is supposed to be .025” and the oil should be topped off or changed regularly. When they run, they run great!
Thanks for the comments. I have learned that if you run 30W oil (not 10W-30 but straight 30W) they do not burn any oil. I use 30W diesel oil from Walmart. If you look on my channel I have a 400 hour review video that I show the oil I use.
Good information. EDIT 2 WEEKS LATER ....Thanks. So i started doing what you suggested, and discovered rather quickly. if you take off the fuel cap, and then the rubber deflector that keeps gas out of the case, The gas tank is NOT ANCHORED BY ANYTHING BUT ECCENTRICS THAT POP INTO THE RAILS. You can take a screwdriver and put it under the tank and just pop it out. This makes doubling the nut unnecessary, and makes cleaning the tank easy.
Good to know. Thanks 😁
Your video was dead on ! thanks for the carb stud trick, I left the linkage hooked up, filled the carb over pulled the float bowl, needle seat and just sprayed B12 carb and choke cleaner and blew it out clean.
Only trick I would suggest is stuffing a shop rag behind the carb so when and if you drop that nut you don't go crazy.
Will you plz show a video installing the fuel filter
I will make one in a few months when I do my next round of service on these generators.
I hate to go thru all that and not replace the needle and seat inside the bowl so appreciate your breakdown. I was gifted the Wen 2000. It held out ok for a day without power during hurricane Ian. Ran it dry afterwards and ran it once a month since. Always started right up. Last month ran it and it slowed down and sputtered off sounding like it was out of gas and now won't restart and small as it is I'm only good for about 10 pulls lol Can't see the spark from the plug grounded well to the case, that's the only thing that little pillar they got there is good for, to hold the plug onto the case and no sparkay so going swap that out and look for a carb kit. Keep on fixing!
Thaanks for posting this video.. i will be removing my carb in the next day or two. Getting ready for rolling winter blackouts here in Texas this winter.
Their is very small filter where fuel line hooks to carb it’s press in the metal line on carb remove it and clean it
Yes on some there is, on others it is not there.
That gas tank is super easy to remove
That's good. Some people may feel that they want to take the extra steps of removing it.
Fuel filter is in the end of the carburetor where the gas line slips on lol.
I have answered this topic before. Yes you are correct there is SUPPOSED TO BE a little white filter that sits in the fuel inlet on the carburetor. This generator did not have one. I have done annual service on over 50 of these units now and it really is hit or miss if they have one or not. Out of the 50 or more I have done I would say less than 20 had those filters. If yours had one then you can count yourself as one of the lucky ones.
Sir thank you for the video I am going to install a filter as preventative maintenance and I will be calling my new generator the harbor freight Nonsense 2000 watt generator
Haha lol 🤣🤣
I use cheese cloth, double it up. Place it the filler cap and pour through into the tank.
No method is fool proof. I have gas jugs with filters on the pour spout and the tank has a screen. Yet I am still pulling a carb and cleaning a tank. I will say this though, I am far from a casual generator user. I have 5 Generators from 1000w to 6kw. I live off grid, and sometimes you just need AC this far south (near Texas Mexico border) or to charge the solar batteries. This 2kw i picked up used for 300$ a few years ago. Its just big enough to run 8 hours on just over a gallon, charge batteries and keep AC running. So it gets run to death.
Good video man.
Just so you know there is a filter thats in the inlet on the carb where the gas line slides over its a tiny white plastic filter.
Must have been missing on mine then.
I haven't gotten that far yet, but the video I was watching it was IN the carb itself. It's IN the hose barb. I'll probably find out for sure over the weekend.
Yes you are correct there is supposed to be a small white filter that goes into the fuel inlet on the carb. I am not sure why mine didn't have one. Thanks for pointing that out.
Mines only runs in start mode will replace it will fix my problem? It always shuts off right away when I slowly try putting it on run
You just need to clean the carburetor. There is a small main jet that gets clogged. Clean the carb and it should run beautifully.
@@Bbernhardsr thanks! Ill get to it right away !! yesterday I just drain the gas out of the thank and carb but never did that step
@@htx5641 ua-cam.com/video/SHADFNhqaW8/v-deo.htmlsi=iXBYMr7TwcHoBepF
Click this video and fast forward to about 5:10
Had like 6 of these now. Can the carb come off if i just cut of the plastic bracket. Seems the only purpose is to block the carborator accessibility