I did this for years for my 2000 navastar t444 I built a centrifugal from a washing machine worked great I pulled a 3 car trailer all over never gave me any problems also ran straight used trans fluid for fuel and used veggie oil truck had 575000 miles on it
Still mixing used motor oil, but now finding that half of what we mix does better with 5:1 ratio of used motor oil to gasoline. We are also now straining the oil before we put it in the plastic drum then adding the gasoline into the drum and stirring it. This thins the oil and it goes thru the filter much easier and quicker. There is less smoke and more power. You can safely go 4:1 or as high as 65/35%.
I think if someone is doing this for a diesel engine, make sure the fuel is thin enough. If it's too thick, it's hard on the fuel pump and harder on the injectors. This also causes issues in the winter months when it gets cold. I also mix my oil with gas. In the summer months, I run a 80:20 ratio. In the winter it's 60:40 ratio and sometimes 40:60 if it gets real cold and this isn't even for a regular diesel, this is for a multi-fuel engine in my M35A2.
He should be diluting with some gas cuz it gets a lot thiner, & if done right it’s almost just thicker than reg diesel. One key to using gas is you need to let it air out, & let the vapors dissipate. But as a diesel guy I have noticed a little more power w my mix than on straight diesel.
Are these kits still available anywhere? Would it hurt to run it through something like Amsoils filtering system and a centrifuge before hand or is it not necessary - just don't want to have to buy injectors or pumps. Also like the idea of gas mixing - sounds cheaper.
If fuel prices get real high then I do the gas oil mix method but when their at or under 3 bucks a gallon I simply filter 2 gallons of 5w/30 into a full tank of offroad diesel it make the fuel brown and it reduced the smoke output. I also do think it stops algie from growing in my fuel tank. Black diesel got me thru 2008 in my vintage 240D
ive gone through two sets of injectors now on a 2001 7.3, truck ran great but after about 5 k the internal orings would wear and fuel would add to my oil sump increasing the oil level and severe power loss, i think its because of the huei system and the thicker black diesel is harder to push out nozzle so pressure is higher causing blowby back to the actuation pressure side and damaged the orings. im gonna try it now with a 12 valve, i think the pintle injector should be ok. ratio ive been running is: 25 gallon 15w40, 20 gallons diesel, 5 gallons gas im mixing all at once, let it sit overnight, pump entire mixture except laste couple inches in 55gal drum, then circulate that mix for a few minutes and run it. note* im running about 100miles a day, so the remaining sits in the tank until the next use
Can do same thing with used cooking oil. Either way get oil hot before straining and filtering. Concerning using gas.. Be carefull. To much gasoline can cause too much heat and not enough engine lube. Best of luck.
Jon Smith was going to use in my 01 7.3 some guys said it’ll blow it up etc etc but they never could prove why ....what do you do to make it and what kinda tips do you have
We have been blending old engine oil with diesel for the past 10 months. Oil is centrifused and passed through 5 micron filter before blending. Have noticed that on some vehicles a black sludge appearing in the fuel system. Is it possible that the blending process is responsible for this sludge appearing?
Sorry Ronald for not keeping up. The pellets come from Matt Macek who has the youtube recyclematt. His phone number is 630-788-4091. They absorb moisture and acid. Rodney Jordan is doing it also and using another pellet that seems to work and is less expensive. His number is 317-902-5812. He also has a youtube channel but I forgot what it was. He has a real nice setup. Hope that helped.
Hi. I have been driving on black diesel for a while and recently quite going places very often. I’m driving on diesel again and switched my fuel filter today, it was still sort of black. How long before the oil is out of my cars system?
4:26 Because you closed the valve! Yet tried to cover up your smarts because "its too cold"! Otherwise, nice vid, you still deserve kudo's for trying to help mankind! Have to ask, do you think a used electric water heater would be sufficient enough heat the used oil before it meets the nozzle? I say this this because I don't believe I ever heard it mentioned and figure I can get one of you tech savvy youtubers to find out? I'm pretty techy myself but limited in my hoarding of anything that I could find useful in the future.
I suggested this to a guy 30 years ago when i was 10 yrs old and i had started to work on diesel engines with an old machine operator down the street.... The idea came to me because of the way we mix 2 stroke.... And i thought if gasoline was that powerful wouldnt motor oil balance it out....he said it was a no way idea and the gas would blow the engine.... I was right
Back in the day there wasn’t such a thing as 2 cycle oil they used just motor and gas to run chainsaws and other 2cycle machines. I bought a old gas air compressor at a yard sale that had the mixing ratio labeled right on the tank
Could someone explain about effect if i mix biodiesel (B20) with olive oil? using 30ml olive oil for 50 litres biodiesel. Could it can increase performance?
This is easier to do with the older engines of the kind that is used in the video but it's probably not something you want to do on a newer engine It would be interesting to know how much the pellets cost and how much yield you get from them
What I’ve been doing for a while now, is since we live in a warm climate, & I used to run my 7.3 PSD on 25% waste oil. Everything was good until I got some Veg & it was down hill from there. Veg oil will ruin diesels if done improperly. Motor oil only needs to be diluted 25% w gas or less depending on thickness sometimes it’s already diluted from shops I get it at. I filter it through a 2 micron filter then my truck gets it. I’ve been running it on that for a while & all seems to be going well so far. When I got my 93 idi I had like 40 gallons of oil I had from a friend & used it pretty quickly. Then got some more which I quickly used up. Then got a new shop where I have been getting loads of 45gal each time. I’ve got 45gal of jerry cans. Between fuel storage & fuel savings Ive come almost even after I filled up my tanks & saved 100-$200. I’ll be getting a better pump so that’ll be changing.
Yeah any non all mechanical diesel should never touch this shit. My idi loves it as well is my previous PSD, but some engines don’t have enough heat to fully burn the extra energy in the oil completely & smoke mostly black.
I've been using lots of wmo too, but I put about 30gallons to 5-10 gallons of gas. I will use a pump and constantly pump it through a 100 micron sock filter and to mix the two better. Once this is done I pump it from one drum to another. A dirty drum to a clean drum. From the dirty to clean, I pump it through a 40 micron filter on the hose and then it goes through a 10 micron sock filter in the clean drum. Seems to work pretty good so far. I've been using this for my Deuce and a half.
From the video, it looked like activated carbon it's used commonly in water filter equipment. And commonly available in bulk for the aquarium industry. I'm, fairly certain there's some incorrect information in the video Out of respect to the channel owner for posting this video please don't take this information the wrong way. I'm only wishing to help profect your system. The system shown is filtered probably with a oil filter, it's probably too thick at this point for a water fuel separator filter. Then goes to mixing the activated carbon is like a sponge but it isn't effective in this manner. It will trap particals yet release them as easily. As far as changing the pH of the acid or filtering out water I have serious doubts. Water can flow through activated carbon easily. Which is one issue, second issue activated carbon rubs together and forms a fine black dust which is similar to a new water filter. One issue is this dust needs to be filtered out as well. I'd suggest Move the activated carbon into a canister filter before your oil is passed through the 10 micron filter. Smaller pump can be positive thing. Oil filters have a spring that allows oil to bypass a filter in the event of a clogged filter. Oil filter Manufacturers would rather feed a engine oil pump dirty oil then no oil. It's highly likely that pump it too high of flow for the cold oil being filtered likely the filter isn't pulling much out contamination. Mixing pump is still used to mix diesel I'd suggest a small glass bodied filter here if anything shows up in it you know earlier filtration has likely failed or you have dirty unfiltered diesel. Better to have a warning then not Before distribution it highly suggested a fuel water separator filter. The oil can easily be packed with water. As for the neutrilizing acid I maybe wrong here but I don't think activated carbon will filter out the acid or change the pH. Maybe if the acid compound is large enough activated carbon could filter it out but not effectively pumped around the tank
I don't worry about water. If I can't see water and oil separation in the tank, then it's not enough water to worry about. I just mix one quart of alcohol to every 20 gallons of oil that I filter. Allows the engine to safely burn any water in the system. The water mixed with alcohol turns into methanol and therefore won't rust or anything. It'll burn like low octane fuel.
kylie oliver polymer pellets are the pellets that are used in some planting mixes to absorb water. They look like little plastic beads. Some beads are used in floral shops. When they absorb water they become like a jelly bead.
Yes, The Crosley was purchased in an auction from the Carswell Air Force Base in Fort Worth, TX in 1981. It was claimed to be General Eisenhower's 1946 Crosley Golf Car. President Eisenhowers"s 1951 Crosley Golf Car was built by the same man and donated to him when he became president. It is now in a museum. This one was the first. I have the sign that came with the car.
If you wish to use a center fuse, go to USfiltermaxx on youtube and meet Steve. His number is:904-334-2838. UA-cam Making Diesel fro WMO Waste Motor Oil Black Diesel Processor. Black Diesel is more powerful than today's diesel. Runs quieter, and if properly cleaned does not hurt your system.
We are having better performance without hurting the engine by mixing some of the fuel added at a rate of 5 gallons used oil to one gallon gasoline. More power, easier starts, less smoke. You can even go as high as 65% used oil to 35% gasoline.
Talk about amateur hour!!! Geezuz! So in all this long winded vid and frigging around, you mix dried and filtered WMO with Diesel. As complicated as that is, I think I got it.
you are professional,because much heavy mental oxide impurities in the used motor oil ,the filtration is not enough,our machine use the high temperature distillation machine technolgy,if you want to know more information,please contact me wechat/what;s app:+8615823899667
Nick Pappagiorgio actually yes there is moisture In oil and yes after engine oil has beeb used it becomes acidic and that’s why it isn’t safe to have on your hands etc it’ll irritate and soak in cause cancer or sickness etc but oh ok your an expert I forgot lmfao
This is NOT SMART at all. If the fuel is black it is black for a reason meaning it is so filled with contaminants that it is BLACK! When the contaminants are filtered out it would be gold colored or clear! Black diesel would be great for a heating unit but not to burn in you $10,000+ tractor! That's just stupid!
Used unfiltered oil does indeed have particals suspended in the oil that's why engine oil lab test can detect particales of lead and other metal alloys to detect engine wear without a engine tear down inspection. Although with proper filtration it should have a effect. The black is the carbon. And a centerfuge is the proper way to go
I did this for years for my 2000 navastar t444 I built a centrifugal from a washing machine worked great I pulled a 3 car trailer all over never gave me any problems also ran straight used trans fluid for fuel and used veggie oil truck had 575000 miles on it
Still mixing used motor oil, but now finding that half of what we mix does better with 5:1 ratio of used motor oil to gasoline. We are also now straining the oil before we put it in the plastic drum then adding the gasoline into the drum and stirring it. This thins the oil and it goes thru the filter much easier and quicker. There is less smoke and more power. You can safely go 4:1 or as high as 65/35%.
gasoline?
I would like to know about the pellets and where to get them? 2/2/2017
Please make another video on this subject. Video making was quite a bit different in 2014. Thanks
I think if someone is doing this for a diesel engine, make sure the fuel is thin enough. If it's too thick, it's hard on the fuel pump and harder on the injectors. This also causes issues in the winter months when it gets cold. I also mix my oil with gas. In the summer months, I run a 80:20 ratio. In the winter it's 60:40 ratio and sometimes 40:60 if it gets real cold and this isn't even for a regular diesel, this is for a multi-fuel engine in my M35A2.
He should be diluting with some gas cuz it gets a lot thiner, & if done right it’s almost just thicker than reg diesel. One key to using gas is you need to let it air out, & let the vapors dissipate.
But as a diesel guy I have noticed a little more power w my mix than on straight diesel.
I have never seen meth made like this
Ohhh wrong video
Are these kits still available anywhere? Would it hurt to run it through something like Amsoils filtering system and a centrifuge before hand or is it not necessary - just don't want to have to buy injectors or pumps. Also like the idea of gas mixing - sounds cheaper.
If fuel prices get real high then I do the gas oil mix method but when their at or under 3 bucks a gallon I simply filter 2 gallons of 5w/30 into a full tank of offroad diesel it make the fuel brown and it reduced the smoke output. I also do think it stops algie from growing in my fuel tank. Black diesel got me thru 2008 in my vintage 240D
Over $3 per liter here in nz. $3 a gallon is cheap as
ive gone through two sets of injectors now on a 2001 7.3, truck ran great but after about 5 k the internal orings would wear and fuel would add to my oil sump increasing the oil level and severe power loss, i think its because of the huei system and the thicker black diesel is harder to push out nozzle so pressure is higher causing blowby back to the actuation pressure side and damaged the orings. im gonna try it now with a 12 valve, i think the pintle injector should be ok. ratio ive been running is: 25 gallon 15w40, 20 gallons diesel, 5 gallons gas
im mixing all at once, let it sit overnight, pump entire mixture except laste couple inches in 55gal drum, then circulate that mix for a few minutes and run it. note* im running about 100miles a day, so the remaining sits in the tank until the next use
I'm more curious about the old white vehicle in the background, what is it?
Haha that's only reason I clicked this video haha his shit going in one ear an out the other
Can do same thing with used cooking oil. Either way get oil hot before straining and filtering. Concerning using gas.. Be carefull. To much gasoline can cause too much heat and not enough engine lube. Best of luck.
what happened to the 1 micron filter
This does work I used to do it in my 2000 7.3
Jon Smith was going to use in my 01 7.3 some guys said it’ll blow it up etc etc but they never could prove why ....what do you do to make it and what kinda tips do you have
Was fuel gritty or does fiter get rid of that oil grit
Heard the 7.3 can drink anything
Where do you get the pellets or what is the name of them
We have been blending old engine oil with diesel for the past 10 months. Oil is centrifused and passed through 5 micron filter before blending. Have noticed that on some vehicles a black sludge appearing in the fuel system. Is it possible that the blending process is responsible for this sludge appearing?
Centrifuge should take all the sludge out of the oil
so deluted 5 gallons deisle by adding 5 gallons oil?
WHAT are the PELLET BAGS ???
What is the white vehicle in the barn in the background? ??
Golf Buggy
Sorry Ronald for not keeping up. The pellets come from Matt Macek who
has the youtube recyclematt. His phone number is 630-788-4091. They
absorb moisture and acid. Rodney Jordan is doing it also and using
another pellet that seems to work and is less expensive. His number is
317-902-5812. He also has a youtube channel but I forgot what it was.
He has a real nice setup. Hope that helped.
Hi. I have been driving on black diesel for a while and recently quite going places very often. I’m driving on diesel again and switched my fuel filter today, it was still sort of black. How long before the oil is out of my cars system?
whats happening if you mix the synthetic oils?
Where u get them pellets? I want some
4:26 Because you closed the valve!
Yet tried to cover up your smarts because "its too cold"!
Otherwise, nice vid, you still deserve kudo's for trying to help mankind!
Have to ask, do you think a used electric water heater would be sufficient enough heat the used oil before it meets the nozzle?
I say this this because I don't believe I ever heard it mentioned and figure I can get one of you tech savvy youtubers to find out?
I'm pretty techy myself but limited in my hoarding of anything that I could find useful in the future.
I suggested this to a guy 30 years ago when i was 10 yrs old and i had started to work on diesel engines with an old machine operator down the street....
The idea came to me because of the way we mix 2 stroke....
And i thought if gasoline was that powerful wouldnt motor oil balance it out....he said it was a no way idea and the gas would blow the engine....
I was right
Back in the day there wasn’t such a thing as 2 cycle oil they used just motor and gas to run chainsaws and other 2cycle machines. I bought a old gas air compressor at a yard sale that had the mixing ratio labeled right on the tank
I dont know why it dont wanna flow???
Maybe cause the flow valve is off
Thanks
Could someone explain about effect if i mix biodiesel (B20) with olive oil? using 30ml olive oil for 50 litres biodiesel. Could it can increase performance?
Olive oil?! That's very expensive in my country.
Brilliant video thank you 👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍, 😎😃👏
This is easier to do with the older engines of the kind that is used in the video but it's probably not something you want to do on a newer engine
It would be interesting to know how much the pellets cost and how much yield you get from them
What I’ve been doing for a while now, is since we live in a warm climate, & I used to run my 7.3 PSD on 25% waste oil. Everything was good until I got some Veg & it was down hill from there. Veg oil will ruin diesels if done improperly.
Motor oil only needs to be diluted 25% w gas or less depending on thickness sometimes it’s already diluted from shops I get it at.
I filter it through a 2 micron filter then my truck gets it. I’ve been running it on that for a while & all seems to be going well so far.
When I got my 93 idi I had like 40 gallons of oil I had from a friend & used it pretty quickly.
Then got some more which I quickly used up.
Then got a new shop where I have been getting loads of 45gal each time. I’ve got 45gal of jerry cans.
Between fuel storage & fuel savings Ive come almost even after I filled up my tanks & saved 100-$200.
I’ll be getting a better pump so that’ll be changing.
Yeah any non all mechanical diesel should never touch this shit.
My idi loves it as well is my previous PSD, but some engines don’t have enough heat to fully burn the extra energy in the oil completely & smoke mostly black.
I've been using lots of wmo too, but I put about 30gallons to 5-10 gallons of gas. I will use a pump and constantly pump it through a 100 micron sock filter and to mix the two better. Once this is done I pump it from one drum to another. A dirty drum to a clean drum. From the dirty to clean, I pump it through a 40 micron filter on the hose and then it goes through a 10 micron sock filter in the clean drum. Seems to work pretty good so far. I've been using this for my Deuce and a half.
working hours to produce a 5 minute run for the car behind
What are and where do you get the pellets?
+Joe Holiday Nope! Still a mystery ~
From the video, it looked like activated carbon it's used commonly in water filter equipment. And commonly available in bulk for the aquarium industry.
I'm, fairly certain there's some incorrect information in the video
Out of respect to the channel owner for posting this video please don't take this information the wrong way. I'm only wishing to help profect your system.
The system shown is filtered probably with a oil filter, it's probably too thick at this point for a water fuel separator filter.
Then goes to mixing the activated carbon is like a sponge but it isn't effective in this manner. It will trap particals yet release them as easily.
As far as changing the pH of the acid or filtering out water I have serious doubts. Water can flow through activated carbon easily.
Which is one issue, second issue activated carbon rubs together and forms a fine black dust which is similar to a new water filter. One issue is this dust needs to be filtered out as well.
I'd suggest
Move the activated carbon into a canister filter before your oil is passed through the 10 micron filter. Smaller pump can be positive thing. Oil filters have a spring that allows oil to bypass a filter in the event of a clogged filter. Oil filter Manufacturers would rather feed a engine oil pump dirty oil then no oil. It's highly likely that pump it too high of flow for the cold oil being filtered likely the filter isn't pulling much out contamination. Mixing pump is still used to mix diesel I'd suggest a small glass bodied filter here if anything shows up in it you know earlier filtration has likely failed or you have dirty unfiltered diesel. Better to have a warning then not
Before distribution it highly suggested a fuel water separator filter. The oil can easily be packed with water.
As for the neutrilizing acid I maybe wrong here but I don't think activated carbon will filter out the acid or change the pH. Maybe if the acid compound is large enough activated carbon could filter it out but not effectively pumped around the tank
I think you can use the pellets that pull moisture from a room you know they come in a net bag and hang it up in a basement or something.
I don't worry about water. If I can't see water and oil separation in the tank, then it's not enough water to worry about. I just mix one quart of alcohol to every 20 gallons of oil that I filter. Allows the engine to safely burn any water in the system. The water mixed with alcohol turns into methanol and therefore won't rust or anything. It'll burn like low octane fuel.
You know your on the right path when your driving a ranger as a grown man
where can i get some of the beads to get rid of the water and bad stuff cheers
Hobby Lobby.
Critical Mass what are they?
I'm joking brother.
kylie oliver polymer pellets are the pellets that are used in some planting mixes to absorb water. They look like little plastic beads. Some beads are used in floral shops. When they absorb water they become like a jelly bead.
Damn birds
That fly got trapped in the container lmao
Backyard engineering. You don't just change viscousity and BTU content of a fuel without damaging the "all-in engineering."
The one thing i know is make sure theres no synthetic....petroleum based oil only
Is the Crosley still there?
Yes, The Crosley was purchased in an auction from the Carswell Air Force Base in Fort Worth, TX in 1981. It was claimed to be General Eisenhower's 1946 Crosley Golf Car. President Eisenhowers"s 1951 Crosley Golf Car was built by the same man and donated to him when he became president. It is now in a museum. This one was the first. I have the sign that came with the car.
Is it for sale and what's the other cat
Where can you buy that used motor oil???
Free on Craigslist. Or ask automotive shops for it
If you wish to use a center fuse, go to USfiltermaxx on youtube and meet Steve. His number is:904-334-2838. UA-cam Making Diesel fro WMO Waste Motor Oil Black Diesel Processor. Black Diesel is more powerful than today's diesel. Runs quieter, and if properly cleaned does not hurt your system.
Charles be careful
Co verging used motor oil to diesel mix.
We are having better performance without hurting the engine by mixing some of the fuel added at a rate of 5 gallons used oil to one gallon gasoline. More power, easier starts, less smoke. You can even go as high as 65% used oil to 35% gasoline.
making up words here "co verging" lmao yeee hawwww
Can I use new pressure oil for diesel
Pressure oil? Never heard of it
Wow this worked great for my tesla
🤣🤣🤣
Gay
hi where can i buy the beds i want to make diesel with filted motor oil for my Diesel mercedes
Who is Charles your front teeth are very nice
if I were mixing any kind of fuel to run in a vehicle and making a video on top of it, I would get everything out of the dirt,,,,just saying.
An its recycling
Too much work
Buy a electric centrifuges, build a system around it and clean 40 gallons at a time.
Less work no extra explosive materials needed.
This man is a danger to the environment and a danger to the ozone layer 🤣 I'm kidding
if theres water in your oil, you need to check head gaskets.
No. All used motor oil has water in it from combustion, Some has quite a bit, other old oil almost none.
People are dumb af not like there is a cup of water in your oil but there is moisture picked up along with metal shavings etc etc etc 😂😂🤷🏻♂️🤷🏻♂️🙄🙄🙄🙄
Check out their website, such a scammer, buyer beware lmao
Talk about amateur hour!!! Geezuz!
So in all this long winded vid and frigging around, you mix dried and filtered WMO with Diesel.
As complicated as that is, I think I got it.
I could discern that within 90 seconds. And when the big one hits....everything will be amateur hour for awhile.
One micron filtration is not enough not even close
you are professional,because much heavy mental oxide impurities in the used motor oil ,the filtration is not enough,our machine use the high temperature distillation machine technolgy,if you want to know more information,please contact me wechat/what;s app:+8615823899667
you have 10 mq filter and then you say it cleans down to 1 mq ,, you dont even know what you talking about ;)
Try this in the new emission tractors and you'll be sorry.
Computers screw everything up. They want a socialist controlled world.
blah blah blah
too fkn complicated. There's not a bunch of acid and water in my oil so why would I bother cleaning it?
Nick Pappagiorgio actually yes there is moisture In oil and yes after engine oil has beeb used it becomes acidic and that’s why it isn’t safe to have on your hands etc it’ll irritate and soak in cause cancer or sickness etc but oh ok your an expert I forgot lmfao
I hear loud chirping birds over whispering talk. Can't understand any of it. Goodbye!!!
Try turning your hearing aids on. If they're already on just simply turn them up. Sometimes people forget they even have hearing aids.
@@phillipbenson7624 Sorry Philip, did you say something? :)
@@keithrawls5606 lol
This is NOT SMART at all. If the fuel is black it is black for a reason meaning it is so filled with contaminants that it is BLACK! When the contaminants are filtered out it would be gold colored or clear! Black diesel would be great for a heating unit but not to burn in you $10,000+ tractor! That's just stupid!
Not good! Used motor oil has metal particles in it which is why it turns black. Putting these particles into the atmosphere is bad.
bainsk8 oil turns black from the carbon deposit at the piston rings not from metal.
Used unfiltered oil does indeed have particals suspended in the oil that's why engine oil lab test can detect particales of lead and other metal alloys to detect engine wear without a engine tear down inspection. Although with proper filtration it should have a effect.
The black is the carbon. And a centerfuge is the proper way to go
Centrifuge