16:40 Instead of trying to install the spring and the control arm at the same time, try the following: 1) Support the rear axle with jack 2) Disconnect both struts from the axle 3) Lower/raise axle as needed to install both lower control arms 4) Move the jack to one of the sides of the axle and raise it up - this will cause the other side to lower. When the other side is low enough, install the spring on that side. 5) Lower the jack so the other side will raise up, putting that spring into position. 6) Repeat the process on the other side with the jack, raise that side to lower the other side, and install the spring. 7) Move the jack back the diff, raise it as needed to reinstall the struts.
For the record: The rear spring pig tail ends are supposed to point towards the driver's quarter panel, both springs. Otherwise the car won't sit at the intended ride height. Great video brother, I've been subscribed for quite some time, hopefully you've picked up a couple of battery impacts & an 18" long 3/8's or 1/2" hand ratchet to make your life easier by now.
All 4 bolts in my lower control arms were seized to the inner sleeve. No amount of muscle, breaker bar or impact gun action was going to work. I used a recip saw with a diamond blade to cut the bolts out. Each cut took 20 minutes. Pretty sure my arms are still vibrating. Since the rubber bushing was pressed up against the mounting surface, this meant I was cutting somewhat through the rubber too. That made a huge mess - rubber everywhere - and because of the friction from the blade, burning rubber smoke and smell.
Yep. I know this is a year old but I'm going to comment anyway. I'm about to order NEW factory rear lower control arms for my foxbody. I've lived with these exact Maximum Motorsports arms for almost 20 years. They are incredibly harsh and squeaky. I know the guys at MM and they make great stuff. But when you add urethane and aluminum bushings to suspension parts it's not good for a non raced daily driver. I had factory arms/bushings for the first 10 years of this cars life and raced it every weekend with no trouble. Us old guys didn't have fancy parts at first with these cars. I bought mine new and still drive it. Going back to factory will hurt nothing. One thought....IF you could buy brand new rubber bushings for the MM arms like in this vid, I'd do that and keep them. But you can't. Excellent video nonetheless. Dude is good to listen to!
@@waynestinyworldI’m having problems with my current control arms right now, but they seem to be aftermarket, like a swivel/bearing instead of a bushing. I’m most likely going to replace them to a bushing control arm instead and maybe that fixes my problem. Do you recommend getting some like these, going oem, or getting the same type it has right now?
@notacarguy_ great. I was going to go with the adjustable ones but the guy at Maximum Motorsports said that we don't need to worry about pinion angle when lowering these cars.
Well, considering that I initially put them in backwards, it took me a couple days to figure some things out. I would definitely give yourself 4-6 hours. If you have a power angled socket wrench, that can save you a lot of time (I didn't have one).
Alright, alright! I still have it. I've been working on another couple videos, but I've been busy trying to pay the bills. The time will come. A sneak peak at what is to come is how I shredded my Nittos twice and how I fixed it.
16:40 Instead of trying to install the spring and the control arm at the same time, try the following: 1) Support the rear axle with jack 2) Disconnect both struts from the axle 3) Lower/raise axle as needed to install both lower control arms 4) Move the jack to one of the sides of the axle and raise it up - this will cause the other side to lower. When the other side is low enough, install the spring on that side. 5) Lower the jack so the other side will raise up, putting that spring into position. 6) Repeat the process on the other side with the jack, raise that side to lower the other side, and install the spring. 7) Move the jack back the diff, raise it as needed to reinstall the struts.
This is a great real-world install video! Its never as easy as the manufactures make it out to be.
Thank you! Nothing ever goes according to plan. lol.
Wow this is the best install video I’ve seen on these. Just got mine installed today
Thank you! These things are pretty awesome, congrats!
This guy deserves more views. Thanks for the upload man!
Thank you! Much appreciated.🙏
For the record: The rear spring pig tail ends are supposed to point towards the driver's quarter panel, both springs. Otherwise the car won't sit at the intended ride height.
Great video brother, I've been subscribed for quite some time, hopefully you've picked up a couple of battery impacts & an 18" long 3/8's or 1/2" hand ratchet to make your life easier by now.
Thanks for the tip! I haven't gotten those impacts yet, but you can guarantee if I did a job like this again, I will definitely be picking those up.
Good choice on control arms. Next get the panhard bar - you'll love it! And nice Rogue setup btw
Thank you! I'll add the panhard bar to the list. lol. And thank, the Rogue setup has been awesome!
All 4 bolts in my lower control arms were seized to the inner sleeve. No amount of muscle, breaker bar or impact gun action was going to work. I used a recip saw with a diamond blade to cut the bolts out. Each cut took 20 minutes. Pretty sure my arms are still vibrating. Since the rubber bushing was pressed up against the mounting surface, this meant I was cutting somewhat through the rubber too. That made a huge mess - rubber everywhere - and because of the friction from the blade, burning rubber smoke and smell.
You should have used four jack stands two to support the body of the car and two to support the rear axle this would have made your life a lot easier
Yeah, I didn't have 4 jack stands and unfortunately, this was my only car at the time. Once it goes up, I can't go anywhere to get other tools! ugh!
@notacarguy_ understandable
I installed these now I have a noise every time I drive over a street bump I don't know what to do
what kind of noise?
Yep. I know this is a year old but I'm going to comment anyway. I'm about to order NEW factory rear lower control arms for my foxbody. I've lived with these exact Maximum Motorsports arms for almost 20 years. They are incredibly harsh and squeaky. I know the guys at MM and they make great stuff. But when you add urethane and aluminum bushings to suspension parts it's not good for a non raced daily driver. I had factory arms/bushings for the first 10 years of this cars life and raced it every weekend with no trouble. Us old guys didn't have fancy parts at first with these cars. I bought mine new and still drive it. Going back to factory will hurt nothing. One thought....IF you could buy brand new rubber bushings for the MM arms like in this vid, I'd do that and keep them. But you can't. Excellent video nonetheless. Dude is good to listen to!
@@waynestinyworldI’m having problems with my current control arms right now, but they seem to be aftermarket, like a swivel/bearing instead of a bushing. I’m most likely going to replace them to a bushing control arm instead and maybe that fixes my problem. Do you recommend getting some like these, going oem, or getting the same type it has right now?
Need to invest in some power tools for sure like a Milwaukee battery ratchet
Ha! you might be right about that.
The amout of curse words I would have had for MM after seeing they had given the wrong directions after I installed it.
HA! Yeah, it was a lot of work to get that control arm in there backwards.
Did you put these after or before lowering your car?
I put these on after lowering the car.
@notacarguy_ great. I was going to go with the adjustable ones but the guy at Maximum Motorsports said that we don't need to worry about pinion angle when lowering these cars.
Thanks for the info. For somebody who's not a car guy, how long did this job take you?
Well, considering that I initially put them in backwards, it took me a couple days to figure some things out. I would definitely give yourself 4-6 hours. If you have a power angled socket wrench, that can save you a lot of time (I didn't have one).
Nice video! Looks like a headache
Thanks! It was, but it would be much less of a headache if I had to do it a second time.
Dude I hope you still have your stang. New content please!!!!
Alright, alright! I still have it. I've been working on another couple videos, but I've been busy trying to pay the bills. The time will come. A sneak peak at what is to come is how I shredded my Nittos twice and how I fixed it.