(08:58): "The combination of baking soda and super glue to create a super hard compound is fascinating! Does this method hold up under heat or prolonged stress? What other creative uses have you discovered for this mixture?
Repairing the fan blades in this way will cause the rotation of the fan blades to become unbalanced. The shaft will oscillate and vibrate. Eventually, the shaft bearings and sockets will come loose much faster than normal.
you can re-balance the fan using hot-glue. First, try to balance it on your fingertip, then if it tips to one side then put a blob of hot-glue on the tip of the blade on the opposite side until the fan is balanced. You don't need it to be perfect, just enough balance that the assembled-fan did not appear to vibrate when running.
Descordo um pouco com essas afirmações, porque o importante aí foi o encaixe na hora da colagem da peça , se foi tudo no ajuste , agora se ficar balançando no giro, aconselho trocar mesmo, porque as outras pás podem estar empenadas.
This video just saved me a fortune! I used this technique to repair one of the props on my twin engine airplane! Yes, I did balance it after the broken blade was repaired. I ran the engines at full throttle as it held like a charm. I’ll give it a test flight before I take any passengers but I’m sure it will hold!
Most people would just buy a new fan in this throw away society. Great to see someone doing repairs. That repair will last many years. If it vibrates just glue small amount of weight opposite blade root or blades for repair. The rpm is very slow, less than 1200 rpm so you probably will not notice any significant imbalance if no weight is added. Great video
Thanks today i learned a new thing about baking soda with glue 🎉 When you mix super glue (cyanoacrylate) with baking soda (sodium bicarbonate), it creates a rapid chemical reaction that results in a hard, solid bond. The baking soda acts as a filler or accelerator, causing the super glue to set much faster and form a stronger, thicker bond. This combination can be useful in certain situations, such as: Repairing small cracks or gaps: The baking soda can help fill in voids or cracks, and the super glue binds the materials together quickly. Creating a DIY "instant plastic": When applied in layers, the super glue and baking soda mixture can form a hardened mass that can be shaped or used for small repairs, like fixing plastic or ceramic items. However, it's important to be careful because the reaction generates heat and can cause the glue to set almost instantly, which might make it hard to work with if you're not prepared. Always apply it quickly and in small amounts, as needed.
El mayor peso en el aspa reparada ocasionará una vibración constante; lo cual a su vez dañará otras partes del sistema. Lo mejor y lo más económico es poner el aspa nueva.
I suggest anybody working with heat on plastic or glue to protect your eyes.. as to the screw part i didn't feel it was necessary..i think the welder head would work just fine .. keep it up 👏👏👏
Uma vez eu usei a malha de um cabo coaxial para unir a parte de plastico de um acabamento do carro, fiz igual ao video, colocando o ferro de solda em cima da malha até derreter e penetrar um pouco no plástico, também derreti pedaços de hellerman para reforçar, não usei cola, mas ficou bom e firme.
Hello! I tested it for about 2 weeks and it’s still good now! It’s running normally! Thanks for watching and leaving your comments! Wish you all the best!
I understand that many people will think that the blades will unbalanced and may cause wobbling. And the vibration may cause damage to some other part of the fan (motor, bearings and etc). I agree this is a legitimate worry, especially from a mechanical engineer's view point. However, I can tell from my actual experience that, if you turn on the fastest speed of the fan and don't feel so much of the vibration, it will be "safe" to use. But of course, you must have the mesh installed in case the blades break. I used to have a fan's blade dropped to ground and broken into several pieces. I just hot glue to glue then back have used the fan for many many years, and have many re-glue in between.
If you did not notice the fan blade that was put on the fan at the end had a silver round sticker on it and the one the was broken had a blue round sticker on its blade. Therefore it appears the repaired one was not the one put back on the fan.
The impact in the balance will be minimum -- if any, as the additional weight is close to the rotation center. Moreover, if some vibration appears, balancing is going to be prety simple. Much more likely is to have vibration due to the misalignment when positioning the blade.
It's best, that if you use to 3D printing, might aswell do it that way 👍🏼 And if has a restore & continued repair / restored method 👍🏼 that would be great / much better ( u know what i mean, when it partially medium to micro repairs 👍🏼 ) and re -cast of for optimal quantity quantum & quality 👍🏼
@@InventorSC thank's 👍🏼 keep up with the " old " tip's too, country with poor oil liquidity will needs it 👍🏼 edit : ua-cam.com/users/shortsLFvGCW4_o7w?si=E0RoDC3p01F0KTMg you can see in this one, nano inches of pure rubber is being sewing into a bag ( it's nearly 99% identical to an operator by production )
In India, it is not a problem to get the spares. Al Indian make fan blades are available and quite cheap. Replace them. Do not create imbalance and spend for the worn-out shaft. Even small imbalance causes reduction in speed.
Очень интересно .Известно,что универсальный клей и сода творят чудеса.Но в этом случае шов усилен шпильками.А потом еше раз проклеен и посыпан содой.Это замечательное решение!
This will cause unbalance So, it is recommended to rebalance it Try to put the same weight on the opposite side in the same location Rebalance will save your fan, bearing and gearbox from any damage over time 👍🏻
the bent wires were used.... look at 6:06. the balance can easily be fixed adding a small weight opposite to the repair. It would be tiny, just a few grams. It would be enough to weigh the wires then add that same weight on opposite side.
If super glue is compatible with the plastic it will make a very strong weld. Using a bolt as soldering iron tip makes no sense as using wire from a coaxial cable! Also, I doubt that the wire gives any extra strength to the blade.
You could use a big nail with a big head, instead of the bolt you got after a lot of work on it (but a plastic gun with all the metal pins to fix every crack in the platic costs about 18 eur) Anyway, using a hot glue gun does the job in a few seconds. Bye
naaahhhh....electric fan blades are readily available in eletronic supply stores or even at junkshops. It's safer and relaiable, and cheap. Fan blade holes are standard, except those for industrial use.
Hello! It’s not fake! I actually repaired it that way! Please try it at home and you will be amazed! Thanks for watching and sharing your feedbacks! Wish you all the best!
Anyone Can Do It! How To Make A Simple Welding Machine From SPARK PLUG At Home
ua-cam.com/video/b8SLi5Gz6Pc/v-deo.html
Super.
Merhaba o tuz neydi ne tuzu anlamadık?
What if the crack is in the midle of the fan blades not of the center joint corner sides
@@PukitaHarold it’s gonna wobble a bit until it cracks
(08:58):
"The combination of baking soda and super glue to create a super hard compound is fascinating! Does this method hold up under heat or prolonged stress? What other creative uses have you discovered for this mixture?
Repairing the fan blades in this way will cause the rotation of the fan blades to become unbalanced. The shaft will oscillate and vibrate. Eventually, the shaft bearings and sockets will come loose much faster than normal.
Hello! Thanks for watching and sharing your great experience! Wish you all the best!
Concordo. O barato sairá mais caro e perigoso.
you can re-balance the fan using hot-glue. First, try to balance it on your fingertip, then if it tips to one side then put a blob of hot-glue on the tip of the blade on the opposite side until the fan is balanced. You don't need it to be perfect, just enough balance that the assembled-fan did not appear to vibrate when running.
Descordo um pouco com essas afirmações, porque o importante aí foi o encaixe na hora da colagem da peça , se foi tudo no ajuste , agora se ficar balançando no giro, aconselho trocar mesmo, porque as outras pás podem estar empenadas.
@@msafwan3010 There are lots or various fan blades on the market in China and the retail price of a new 3~5 USD
This Guy really loves ❤️ this Fan.😊
Thanks for watching and leaving your comments! Have a nice day!
Have a good 👍 one.
..but not his safety!!! pls dont ever try it!!!
This video just saved me a fortune! I used this technique to repair one of the props on my twin engine airplane! Yes, I did balance it after the broken blade was repaired. I ran the engines at full throttle as it held like a charm. I’ll give it a test flight before I take any passengers but I’m sure it will hold!
Thanks for watching and sharing your great experience! Wish you all the best
😂😂
I'm sure you're an employee of Boeing
@@softpure Hysterical!
Most people would just buy a new fan in this throw away society. Great to see someone doing repairs. That repair will last many years. If it vibrates just glue small amount of weight opposite blade root or blades for repair. The rpm is very slow, less than 1200 rpm so you probably will not notice any significant imbalance if no weight is added. Great video
Hello! Glad to hear that! Thanks for watching and sharing your great experience! I would love to learn your methods! Wish you all the best!
I believe this video is more regarding the bonding and how strong it is then how the fans are going to operate. Great video
Thanks for watching and sharing your feedbacks! Wish you all the best!
Wow, I had no idea plastic could be repaired so easily! This technique is definitely going to come in handy. Thanks for sharing!
Glad to hear that! Have a good day!
please dont try it!!!
I know a great idea when I see one. I ignore haters who think they're high and lofty
Glad to hear that! Thanks for watching and leaving your comments! Have a nice day!
Even if you're 50!! Thanks a lot.
Thanks for watching and leaving your comments! Wish you all the best!
blades weight will not balance any more. Where can use again. Even though can use, later motor also will have problem due to unbalanced wings
Thanks for watching and sharing your feedbacks! Wish you all the best!
Can be balance like another fan or blade.
This is such an incredible technique! I never realized plastic repair could be this simple. Thanks for sharing this amazing method!
Glad you liked it! Thanks for visiting the channel and leaving your comments! Have a good day!
มันใช้ไม่ได้แร้วมันขาดความสมดุลของมันแร้ว.ถึวแม้จะใส่กาวแร้วก็ตาม.ไปหาซื้อใบพัดใหม่ดีกว่าคับ
Thanks for watching and sharing your feedbacks! Wish you all the best!
Thanks today i learned a new thing about baking soda with glue 🎉
When you mix super glue (cyanoacrylate) with baking soda (sodium bicarbonate), it creates a rapid chemical reaction that results in a hard, solid bond. The baking soda acts as a filler or accelerator, causing the super glue to set much faster and form a stronger, thicker bond. This combination can be useful in certain situations, such as:
Repairing small cracks or gaps: The baking soda can help fill in voids or cracks, and the super glue binds the materials together quickly.
Creating a DIY "instant plastic": When applied in layers, the super glue and baking soda mixture can form a hardened mass that can be shaped or used for small repairs, like fixing plastic or ceramic items.
However, it's important to be careful because the reaction generates heat and can cause the glue to set almost instantly, which might make it hard to work with if you're not prepared. Always apply it quickly and in small amounts, as needed.
Have a nice day!
Very smart thanks sharing
Glad to hear that! Thanks for watching and leaving your comments! Have a nice day!
El mayor peso en el aspa reparada ocasionará una vibración constante; lo cual a su vez dañará otras partes del sistema. Lo mejor y lo más económico es poner el aspa nueva.
Hello! Thanks for watching and sharing your feedbacks! Can you share how you do it? I would love to learn your methods! Wish you all the best!
Very Good, Nice Work 👍🏻
Glad to hear that! Thanks for watching and leaving your comments! Have a nice day!
I suggest anybody working with heat on plastic or glue to protect your eyes.. as to the screw part i didn't feel it was necessary..i think the welder head would work just fine .. keep it up 👏👏👏
Hello! Thanks for watching and sharing your feedbacks! I appreciate that! Wishing you a great day!
Take it as an idea to repair something that cannot be bought or not available anymore 👍👍👍
Thanks for watching! Wishing you a great day!
Daaaamn!
Thanks for watching! Wishing you a great day!
Uma vez eu usei a malha de um cabo coaxial para unir a parte de plastico de um acabamento do carro, fiz igual ao video, colocando o ferro de solda em cima da malha até derreter e penetrar um pouco no plástico, também derreti pedaços de hellerman para reforçar, não usei cola, mas ficou bom e firme.
Hello! Thanks for watching and sharing your great experience! I would love to learn your methods! Wish you all the best!
Super! Thank you very much!
Glad you liked it! Thanks for watching! Have a nice day!
What about balancing?
Hello! I tested it for about 2 weeks and it’s still good now! It’s running normally! Thanks for watching and leaving your comments! Wish you all the best!
Add the same weight on every blade.
Add some sticker at other blade
God bless you
Thanks for watching and leaving your comments! Have a nice day!
Had a similar break in the same type of fan blade, 2part epoxy was used, lasted for months of 24/7 use
Thanks for watching and sharing your great experience! I would love to learn your methods! Wishing you a great day!
I understand that many people will think that the blades will unbalanced and may cause wobbling. And the vibration may cause damage to some other part of the fan (motor, bearings and etc). I agree this is a legitimate worry, especially from a mechanical engineer's view point. However, I can tell from my actual experience that, if you turn on the fastest speed of the fan and don't feel so much of the vibration, it will be "safe" to use. But of course, you must have the mesh installed in case the blades break. I used to have a fan's blade dropped to ground and broken into several pieces. I just hot glue to glue then back have used the fan for many many years, and have many re-glue in between.
Hello! Thanks for watching and sharing your great experience! I appreciate that! Wish you all the best!
If you did not notice the fan blade that was put on the fan at the end had a silver round sticker on it and the one the was broken had a blue round sticker on its blade. Therefore it appears the repaired one was not the one put back on the fan.
Hello! Thanks for watching and sharing your feedbacks! I would love to learn your methods! Wish you all the best!
You must be color blind! That is the same fan blade...no question!
There are lots of various fan blades on the market in China and the retail price of a new 3~5 USD
Hello! Thanks for watching and sharing your feedbacks! Wishing you a great day!
Would have to do the same with all fan blades to make the fan balenced without effecting the barring
Hello! Thanks for watching and sharing your feedbacks! I would love to learn your methods! Wish you all the best!
Yes. A small issue with the blades causes the bearing to wear frequently. I have experienced this myself.
Wow
Thanks for watching and leaving your comments! Have a nice day!
The impact in the balance will be minimum -- if any, as the additional weight is close to the rotation center. Moreover, if some vibration appears, balancing is going to be prety simple.
Much more likely is to have vibration due to the misalignment when positioning the blade.
Hello! Thanks for watching and sharing your feedbacks! Can you share how you do it? I would love to learn your methods! Wish you all the best!
vey good
Glad to hear that! Thanks for watching and leaving your comments! Have a nice day!
Я так пластик клеил на мотоцикле, очень надёжно получается 👍
Thanks for watching and leaving your comments! Have a nice day!
Not bad like the quick response
Thanks for watching and sharing your feedbacks! Wishing you a great day!
Đắt hơn giá mua cái mới
Hello! Thanks for leaving your comments! Have a nice day!
It's best, that if you use to 3D printing, might aswell do it that way 👍🏼
And if has a restore & continued repair / restored method 👍🏼 that would be great / much better
( u know what i mean, when it partially medium to micro repairs 👍🏼 ) and re -cast of for optimal quantity quantum & quality 👍🏼
Thanks for watching! Wishing you a great day!
@@InventorSC thank's 👍🏼
keep up with the " old " tip's too, country with poor oil liquidity will needs it
👍🏼 edit : ua-cam.com/users/shortsLFvGCW4_o7w?si=E0RoDC3p01F0KTMg
you can see in this one, nano inches of pure rubber is being sewing into a bag ( it's nearly 99% identical to an operator by production )
Best buy a new one. Safer 👌
Thanks for watching and sharing your feedbacks! Wish you all the best!
In India, it is not a problem to get the spares. Al Indian make fan blades are available and quite cheap. Replace them. Do not create imbalance and spend for the worn-out shaft. Even small imbalance causes reduction in speed.
Thanks for watching and sharing your feedbacks! Wish you all the best!
Its better buy a new one .❤❤❤
Thanks for watching and sharing your feedbacks! Wish you all the best!
I used fishing line to stitch the broken blade. Use gorilla tape patch to balance the blades.
Wow! Thanks for watching and sharing your great experience! I would love to learn your methods! Wish you all the best!
Nope. Buy a new fan blade.
Thanks for watching! Wishing you a great day!
Se você não se importar com a aparência pode usar só algodão e cola. Fica bem forte.
Hello! Thanks for watching and sharing your great experience! I would love to learn your method! Wish you all the best!
Wouldn't just some methylene chloride work on ABS to do a solvent bonding that melts the cracks together
Thanks for watching and sharing your great experience! Wishing you a great day!
The point of the video isn't how to repair fan blades, it's how to repair plastic.
Thanks for watching and sharing your feedbacks! Wish you all the best!
Superglue and baking soda.
Yeah! Thanks for watching and leaving your comments! Have a nice day!
Очень интересно .Известно,что универсальный клей и сода творят чудеса.Но в этом случае шов усилен шпильками.А потом еше раз проклеен и посыпан содой.Это замечательное решение!
Hello! Glad you liked it! Thanks for watching and sharing your feedbacks! Wish you all the best!
@@InventorSC Thank you very much!
fan bLade price is....PhP 35! so I won't waste this much time & effort..
Thanks for watching! Wishing you a great day!
Much easier and safe to buy fan blade at repair shops, its available there.
Thanks for watching! Wishing you a great day!
Does the weight of the wire mess with the balance?
I think it’s ok! It's not too much heavier than the original! Thanks for watching and leaving your comments! Have a nice day!
Nice Repair. Unfortunately a repair like that comprises the Blades integrity.
Hello! Thanks for watching and sharing your feedbacks! Wish you all the best!
In the civilized world we are living in, we rank product safety highly. We do not necessarily fix something like this.
Thanks for watching and sharing your feedbacks! Wishing you a great day!
This will cause unbalance
So, it is recommended to rebalance it
Try to put the same weight on the opposite side in the same location
Rebalance will save your fan, bearing and gearbox from any damage over time
👍🏻
Hello! Thanks for watching and sharing your great experience! I would love to learn your methods! Wish you all the best!
This can be done by reversing the rod from its wide end.
Hello! Nice to meet you! Thanks for visiting the channel and leaving your comments! Have a nice day!
Can I use T50 staples?
Yes, of course! I think it’s also really good!
Should be a lot lighter so the balance should be fine with a little wobble
Why did you bend the pieces of wire and not use them. And as pointed out in previous comments the blade assembly is likely to be unbalanced.
Hello! Thanks for sharing your feedbacks! Wish you all the best!
the bent wires were used.... look at 6:06. the balance can easily be fixed adding a small weight opposite to the repair. It would be tiny, just a few grams. It would be enough to weigh the wires then add that same weight on opposite side.
هى ريشة المروحة غالية قوى
Hello! Thanks for watching and sharing your feedbacks! Wish you all the best!
ซื้อใหม่เถอะไม่แพง😂😂
Thanks for watching! Wishing you a great day!
How long can it last? Maybe few days.
Hello! It still works normally after a month! Thanks for watching and sharing your feedbacks! Wish you all the best!
That will repair the propeller but the added weight will make it spin oit of balance.
Hello! Thanks for watching and sharing your feedbacks! Can you share how you do it? I would love to learn your methods! Wish you all the best!
Well,the only way to correct it is to put weights on other blades as counter balance and it will work fine.
Thanks for your great experience! Have a good day!
Time killer
Thanks for watching! Wishing you a great day!
I think staple wires is just as effective
Yeah, I think so! Thanks for watching and sharing your feedbacks! Wishing you a great day!
it is much better to buy a replacement fan blade than doing that repair. 😊
Thanks for watching and sharing your feedbacks! Wish you all the best!
If super glue is compatible with the plastic it will make a very strong weld. Using a bolt as soldering iron tip makes no sense as using wire from a coaxial cable! Also, I doubt that the wire gives any extra strength to the blade.
Hello! Thanks for watching and sharing your feedbacks! Can you share how you do it? I would love to learn your methods! Wish you all the best!
Hello! Thanks for watching and leaving your comments! Have a nice day!
Waste of time!!! Just buy a new one that's cheaper & less effort...
Thanks for watching and sharing your feedbacks! Wish you all the best!
Technique can work on many similar repairs.
Não dá certo porque fica desbalanceado o tempo que gastou paga comprar uma hélice nova balanceada.
Hello! Thanks for watching and sharing your feedbacks! Can you share how you do it? I would love to learn your methods! Wish you all the best!
He took so long and added weight so the fan will not run evenly. Just weld the plastic with the soldering and some cable ties. Simple.
Thanks for watching and sharing your great experience! I would love to learn your methds! Wish you all the best!
no problem with balance here
Thanks for watching! Wishing you a great day!
Залепил скобами, руки оторвать. На мыло!
Thanks for watching! Wishing you a great day!
Better buy a new fan blade, it is cheap and to avoid danger fixing that broken fan blade
Thanks for watching! Wishing you a great day!
What does 50 years of age have to do with this repair ???😮😮😮
Thanks for watching! Wishing you a great day!
the music is so bad can't you find another tune
Yes of course! Thanks for watching and sharing your feedbacks! Wish you all the best!
You fix the blade? What aboit the balance elise? Im sure its out of balance afyer you fix it,
Hello! Thanks for watching and sharing your feedbacks! Can you share how you do it? I would love to learn your methods! Wish you all the best!
Come on. Buy a new blade. So cheap
Thanks for watching and sharing your feedbacks! Wish you all the best!
It's not about buying the blade, its about learning the technique for other stuff
@irvinglechuga2067 need to balance those blades after repair. Not worth it
Yeah it will apply not at this thing but also a lot
Where?
You could use a big nail with a big head, instead of the bolt you got after a lot of work on it (but a plastic gun with all the metal pins to fix every crack in the platic costs about 18 eur)
Anyway, using a hot glue gun does the job in a few seconds.
Bye
Hello! Thanks for watching and sharing your great experience! I would love to learn your methods! Wish you all the best!
Waste of time.new is available at cheap rate.
Hello! Thanks for watching and sharing your feedbacks! Wish you all the best!
Now u have one unbalanced pos fan made of brittle plastic. Go online and buy an aluminum fan, last forever
Thanks for watching and sharing your feedbacks! Wish you all the best!
And all that equipment. Who the fudge has got that c'mon
Thanks for watching and sharing your feedbacks! Wish you all the best!
..or you just order a new one online 😂
Thanks for watching and sharing your feedbacks! Wish you all the best!
This will not make the blade balance then the bushing will be damaged then overheat the motor
Hello! Thanks for watching and sharing your feedbacks! Can you share how you do it? I would love to learn your methods! Wish you all the best!
Super glue and baking soda would have done the trick.
Thanks for watching and leaving your comments! Have a nice day!
naaahhhh....electric fan blades are readily available in eletronic supply stores or even at junkshops. It's safer and relaiable, and cheap. Fan blade holes are standard, except those for industrial use.
Thanks for watching and sharing your great experience! Wish you all the best!
10÷10
Hello! Thanks for watching and leaving your comments! Have a nice day!
làm mất công mất việc ra mua 15k là sài
Thanks for watching! Wishing you a great day!
And if you are 60, then you don't need to know, ok i don't care then😁, thanks i am relaxed now
Thanks for watching! Wish you all the best!
Jitna time aur paisa yahan kharch ho raha uss se kam mein Naya blade aajayega.
Thanks for watching and sharing your feedbacks! Wish you all the best!
What about five years old?
Thanks for watching and sharing your feedbacks! Wish you all the best!
Crap, I'm 75. Now what do I do?
Hello! Thanks for watching and sharing your feedbacks! Can you share how you do it? I would love to learn your methods! Wish you all the best!
Just buy a dam new fan blade..... 😊
Thanks for watching and sharing your feedbacks! Wish you all the best!
Where? Chinese product🤡🤡🤡🤡
FAKE VIDEO. The repaired fan has a different sticker than the fan it runs in the end.
Hello! It’s not fake! I actually repaired it that way! Please try it at home and you will be amazed! Thanks for watching and sharing your feedbacks! Wish you all the best!
How come there is always people being negative. However they watch and you make $$
Not balance anymore😢
Hello! Thanks for watching and sharing your feedbacks! Can you share how you do it? I would love to learn your methods! Wish you all the best!
Buy a new fan throw the old one away!
Thanks for watching! Have a nice day!
а снять оплетку с кабеля и вплавить ее вместо онанизма с кусочками провода?
Thanks for watching! Wishing you a great day!
Waste of time. Centrifugal force will act along line of straight splints. So they achieve very little.
Thanks for watching! Wishing you a great day!
God is good all the time!
Thanks for watching! Have a good day!
And now your blade is QUITE UNBALANCED! HOOOOORRRAAAYYY!!!
Hello! Thanks for watching and sharing your feedbacks! Can you share how you do it? I would love to learn your methods! Wish you all the best!
Così si sbilancia e vibra. Non va bene
Hello! Thanks for watching and sharing your great experience! Can you share how you do it? I would love to learn your methods! Wish you all the best!
The effort is not worth it. Fan blades are cheap
Hello! Thanks for watching and sharing your feedbacks! Wish you all the best!
Nah.. I'll just go and buy new blade 😂
Thanks for watching and sharing your feedbacks! Wish you all the best!
真费劲，剪一块易拉罐的铁皮粘上也就是了，若显得不美观就在外面贴点红纸。
Thanks for watching! Wishing you a great day!
É só pedir outra hélice ao fabricante
Thanks for watching! Wishing you a great day!